Search Documents

By R. A. Pallanch

Sodium sulfite as a zinc retarding agent in the selective Hotation of complex lead-zinc sulfide ores was discovered by the writer in the summer of 1919 in the testing laboratory of the U. S. Smelting, Refining & Mining Co.'s gravity concentrator at Midvalc. Utah. It proved to be the first reagent to give consistently good results in the laboratory on the cornpanj's Bingham ore. In December, 1919, C. A Lemke, concentrator superintendent, recommended that a flotation unit be added to the existing gravity mill to handle the mill slimes, using sodium sulfite as the zinc depressant Owing to the poor lead and zinc markets and the unfavorable royalty schedules offered by the Minerals Separation Co., the project fell through at this time. In 1921, a number of laboratory tests were made at Midvale. on other ores, among them ore from the Sunnyside mine at Eureka, Chlo. Both sodium and calcium sulfites were used with succcss on this ore. Early in 1923, further tests were made at Eureka, shortly after the Sunnyside company had resumed operations after a two-year shutdown. AS a consequence sodium sulfite was given a trial in the mill. The results showcd sufficient improvement over previous work as to warrant continuous use of this reagent in the lead circuit Exeept for a week or so in 1926 and for several weeks in April, 1927, when sodium cyanide and zinc sulfate were given trial runs in this mill. sodium sulfite has been used ever sinee.. Sodium sulfite was chosen rather than the calcim sulfite brcauscl of its gre1ater sollubility, making it possitdr. to introduee the reagent as a solutiun. This Solution is introdueed into the Marry ball mills along with the original feed of ore,. The consumption of sodium sulfite in the Sunnyside mill varies from 1/4 to 12 lb per ton of ore, the smaller amount probably being nearer the average. In February, 1924, laboratory work at Midvale demonstratcd conclusivcly that good results could be obtaincd on the company's Bingham ore and on most of the custom ores tested by using sodiuin sulfite as the zinc depressant, xanthate as the lead enhancer in the lcad circuit, followed by copper sulfate and additional xanthate to float the zinc Sodium sulfide was used to float the iron pyrite after the lead and

Jan 1, 1928

By Lucien Eaton

VENTILATION in the iron mines of the Lake Superior region in nearly all cases is natural; that is, it is induced by the difference in elevation between different outlets in the mine and by the difference in temperature of the air in the mine and that outside. This difference in temperature is frequently augmented by placing a steampipe in the upcast shaft; but aside from this, artificial aids to ventilation have been rare until - recent years. In some of the older mines, as at the Cliffs Shaft mine at Ishpeming, Mich., in the 80's, fans have been used when there was only one opening to surface, but their use was abandoned as soon as a natural circulation of air started. In recent years, the Newport mine at Ironwood, Mich., was the first to use positive mechanical ventilation. The installation was not large enough, however, to give definite results, reliance being placed largely on natural ventilation. With the coming of warm weather in the spring of 1914, the necessity of positive mechanical ventilation at the Lake mine of the Cleveland-Cliffs Iron Co. at Ishpeming, Mich., became evident. The workings of the Lake mine are under the bed of old Lake Angeline, which was pumped out in 1894, and the mine had been in operation for 6 years prior to that date making a total of 26 years of continuous operation. The total production, up to 1914, amounted to over 8,000,000 tons. The ore was first mined by square-set rooms and pillars, but this was later changed to top slicing and caving. Both methods required the use of large amounts of timber, probably 80,000,000 board feet in all, practically all of which remained in the timber mat. The slow oxidation of this timber was one of the principal causes leading to the installation of mechanical ventilation. The mine was served by only one working shaft, called No. 4, a second outlet being provided by a raise to the surface from the old workings on the south side of the mine. This raise was the "down cast;" but it was very small and the drifts and raises leading to it were too small and crooked to permit an adequate amount of air to enter the mine, especially during the warmer weather. Measure-

Jan 8, 1920

By Valentin R. Garfias

The production of petroleum in the Mexican fields during 1931 followed the downward trend of the past nine years, with a decline of close to 6,600,000 bbl., or about 17 per cent from the 1930 total. The output was close to 32,964,000 bbl., the Tampico-Tuxpam fields showing the largest actual and proportional decline, while the production of the fields in the Isthmus of Tehuantepec remained practically unchanged. Wildcatting along the international border was carried on more actively than in previous years, the only successful completion being the Alberca No. 1 well located about eight miles from the international boundary, across from Roma, Tex. This well, completed at a depth of 2015 ft. and plugged back to 1550, is rated at about 6,000,000 cu. ft. of gas per day from a horizon between 1330 to 1540 ft., and is now connected to the gas line from the Jennings gas field, Texas, supplying the city of Monterrey. Favorable oil indications have been encountered in other exploratory wells along the border and drilling will probably continue as these lands are largely held under government concessions which require continuous development work in order to retain title. Development in the Isthmus of Tehuantepec has progressed in a systematic manner, the number of successful completions during the year being considerably larger than in the South or Northern fields. The oil pipe line from the south fields to Mexico City has been completed and its operation and that of the Azcapotzalco refinery is expected to begin early in 1932. The construction of this line will Tevolutionize the transportation of petroleum and its products from the fields to the high plateau and seriously affect the revenues of the government-owned railroads. General conditions in the oil industry were reflected in Mexican operations. Low prices and the imminent threat of an American oil tariff discouraged development work necessary to maintain or increase production, and the curtailment of activities resulted in considerable reductions in personnel by all companies. Early in 1932 the Mexican Government announced its intention to create a surface tax or yearly rental on oil lands equivalent to about 31/4 U. S. cents per acre. Such additional burden on this already harassed industry will not only create little or no

Jan 1, 1932

By George W. Small

The ore, as it is raised from the mine, has all average assay-value of $11 per ton, chiefly in the form of free gold. All the ore goes directly to the stamp-mills, of which there are two. The older and larger mill contains sixteen batteries of five stamps each, with one Frue vanner to each battery. The new mill has eight batteries of five stamps and two Frues to each battery. The large mill is driven by Leffel turbine wheels, with a pressure of eighty feet, and a consumption of 600 miners' inches of water. The smaller mill is driven by "hurdy-gurdy" wheels with a pressure of about 550 feet and a consumption of 150 inches of water. At both mills the tailings from the stamps pass over about 20 feet of plates on their way to the Frues. In each set of plates the first or upper one is copper, the rest are so-called silver plates. The bullion from the stamps is about 800 fine in gold and 200 in silver. The concentrates from the Frues average from 11/4 to 1 ; per cent. of the ore stamped. They very rarely exceed 2 per cent. I was unable to get the exact assay-value of the concentrates, but it is said to vary between $100 and $200 per ton. The concentrates are treated at the chlorination works at the rate of one hundred tons per month. The capacity of the works is somewhat greater than this, but as the supply of concentrates is limited it is not deemed advisable to work them up any faster. Care is taken to keep the concentrates always damp until they are put into the roasting furnace. If this is not done, a decomposition of the pyrites begins, forming lumps which do not roast, and which consequently cause a loss of gold in the residues from leaching. A Fortschaufelungsofen is used for roasting. Its dimensions, incloding fire-box, are 12' X 80'. The hearth is one continuous plane, but the charges, of which there are three in the furnace at one time, are kept entirely separate. The furnace-men call the three compartments, the "drying," the " burning," and the " cooking" compartments. In the middle, or "burning" compartment, the ore is spread

Jan 1, 1887

By Geo. H. Ashley

THE year 1923 saw a decline in the production of crude oil and a strong advance in the production of natural gas. The production of petroleum in Pennsylvania has been remarkably uniform for many years, but with a slight average decline. Until 1918, production was maintained above 7,500,000 bbl. Four of the six years from 1918 to 1923, inclusive, saw a yield of between 7,400,000 and 7,500,000 bbl.; 1923 gave only 7,253,000 bbl. The production of natural gas in Pennsylvania has been variable, reaching a maximum of 138,000,000,000 cu. ft. in 1906 and nearly reaching that figure again in 1907 and 1917. In 1921 production dropped to 86,000,000,000 cu. ft., and it seemed that a rapid decline had set in. Prices were raised by most of the gas companies, and -these raises sustained by the Public Service Commission. Possibly as a result of this and the better prices realized, drilling in the gas fields has been active. The year 1923 has not been prolific in large oil wells. The largest single well was drilled by the Manufacturers Light & Heat Co. on the William Auld farm near Prosperity, Morris township, Washington County. This well started at 225 bbl, but quickly dropped to 60 bbl. A 100-bbl. well was struck in September in Springhill township, Greene County. Three wells in the Tidioute pool started at 50 bbl. or better, and a well near the 28th Ward, Pittsburgh, came in at 60 bbl. One well in Washington County started at 50 bbl., but all of the other wells started at less than 20 bbl. The Tidioute pool, which was the sensation of 1922, had by Jan. 1, 1923, dropped in daily total production to 1430 bbl., by Feb. 1 to 1040 bbl., and by May 1 to 700 bbl. At that time, most of the wells were still flowing naturally, though, as the gas pressure was rapidly decreasing, it was not anticipated that such a flow would long continue. As the wells in this pool started at from 500 to. 800 bbl.. a day, it is evident how rapidly they fell off. In August, 1922, the average production per well per day was 44 bbl. ; in February, 1923, 4 bbl.

Jan 3, 1924

By P. Barnes

(Read at the Philadelphia Meeting, February, 1878.) IT may be of interest, and perhaps of importance, to the members of the Institute that specific mention should be made in detail of the great value of this method of copying or photographing all kinds of tracings.* Several samples are laid upon the table which may serve as illustrations of the results obtained. Some of these show slight imperfections, depending upon the character of the tracing, and upon the length of the exposure to the light, but it may be clearly seen that even a faint copy would be quite available for actual use. The process is believed to be of French origin, and has been used for many years. Special attention seems to have been directed to it recently, and its great value to engineers appears likely to be fully recognized. The manipulations required are of the simplest possible kind, and are entirely within the skill and comprehension of any office boy who can be trusted to copy a letter in an ordinary press. These particulars may be summarized somewhat thus 1. Provide a flat board as. large as the tracing which is to be copied. 2. Lay on this board two or three thicknesses of common blanket, or its equivalent, to give a slightly yielding backing for the paper. 3. Lay on the blanket the prepared paper with the sensitive side uppermost. 4. Lay on this paper the tracing, smoothing it out as perfectly as possible so as to insure a perfect contact with the paper. 5. Lay on the tracing a plate of clear glass, which should be heavy enough to press the tracing close down upon the paper. Ordinary plate-glass of ill thickness is quite sufficient. 6. Expose the whole to a clear sunlight, by pushing it out on a shelf from an ordinary window, or in any other convenient way, for six to ten minutes. If a clear skylight only can be had, the exposure must be continued for thirty or forty-five minutes, and under a cloudy sky, sixty to ninety minutes may be needed. * The introduction of this process into the United States is due principally to Mr. A. L. Holley, who first drew the attention of American engineers to its simplicity and convenience. Mention was also made of the process at the meeting of the Institute in New York, in February, 1877, by Mr. Ogden Haight.

Jan 1, 1878

By J. T. Brown

AS far as could be ascertained, no one had previously investigated the creep strength of silicon poly-crystals. Literature has appeared showing evidence for plastic deformation in silicon single crystals and whiskers.*1"6 Also the fact that germanium, a material of similar crystal structure to silicon undergoes plastic deformation under stress at temperatures above about 60 pct of its melting temperature, has been known for some time.2"4'7 This investigation was performed for the purpose of determining the strength and ductility of silicon polycrystals under creep conditions that would give fairly long times to rupture. PROCEDURE The silicon specimen blanks were obtained by first placing granulated transitor grade silicon (99.999 + pct pure) in a silica crucible. The crucible was surrounded by a graphite susceptor, and induction heating was used for melting the silicon in a vacuum furnace. Blank specimens were formed by freezing molten silicon onto a polycrystalline seed of silicon in a vacuum furnace. The seed was attached to a motor driven revolving rod. As silicon solidified, this rod was gradually withdrawn from the melt. A shape with a contracted center section was obtained by varying the rate of withdrawal from the melt. Specimens for the creep-rupture tests were ground from these "pulled" blanks. Creep-rupture tests were performed in spring loaded machines under constant load at 1800" and 2000° F. RESULTS AND DISCUSSION A test specimen which was sectioned longitudinally is shown in the photomacrograph in Fig. 1. Very little deformation has taken place in the portion of the specimen shown, however, slip lines from several slip systems within the same grain, and deformation band formation was seen. The elongated appearance of the grains is due to the method of growing the specimens. One of the most interesting aspects of the results obtained from the creep-rupture tests was the high strength and the accompanying large amount of ductility. The data obtained is listed in Table I which shows the stress to rupture in 100 hr at 2000°F is between 8000 and 9000 psi. This indicates that silicon's strength at 2000°F is about equal to that of the best commercial super-alloys. It is important to mention that silicon has less than 1/3 the density of iron-, nickel-, and cobalt-base alloys. The usual type alloys for high-temperature applications

Jan 1, 1960

By P. P. Gregory

Natural petroleum gas occurring in the oil-bearing reservoirs is found to exist either as free gas associated with the oil and/or in solution in the oil. In some virgin fields practically no free gas is encountered under the reservoir conditions of pressure and temperature, although in other fields a considerable section of the "pay" horizon is occupied by free gas. In other words, a given oil field may or may not have a gas cap before the exploitation takes place. However, when the reservoir pressure is reduced to a point below the critical saturation pressure by withdrawals of fluids from the producing formation, the gas dissolved in the oil inevitably begins to come out of solution and becomes free gas. Under the controlled methods of production and drilling, a portion of this gas is produced with the oil to the surface and a portion of it remains within the reservoir to accumulate at higher structural levels toward which it migrates by virtue of its low specific gravity. The rate of growth of a gas cap in a given structure depends primarily upon the rate of decline in the reservoir pressure. If the rate of pressure decline is rapid, the gas cap likewise will grow rapidly. On the other hand, shrinkage in the gas-cap area was noted in some fields in which reservoir pressures wereincreasing. Determination of Gas-oil Contact and Thickness of Gas Cap The gas-oil contact can be conveniently located in the process of drilling a well and by electrical logging. However, very little can be found in the petroleum literature concerning methods of predetermining gas-oil contacts in producing reservoirs. Therefore, the writer feels justified in describing briefly a simple, workable, and inexpensive method of determining gas-oil contacts and outlining the limits of gas-cap areas in a field where such knowledge may be essential for efficient production and development operations. The method involves the determination of the following data: (I) Structural data, such as the depth or elevation of the top' of "pay" horizon; (2) reservoir pressures; (3) tubing and casing pressures at the well head; (4) static oil-pressure gradient; (5) static gas-pressure gradient. These data can be secured with a minimum of expense, inasmuch as the

Jan 1, 1938

By Howard B. Bradley, Charles F. Weinaug

The phase behavior of a naturally occurring hydrocarbon system whose critical temperature is near the reservoir temperature has been described. The same volume per cent liquid was observed for the firkt time at three different pressures for isotherms immediately below the critical temperature. The shapes of the isothermal equilibrium constant curves necessary to predict this phenomena are discussed and illustrated. INTRODUCTION The phase behavior of a number of hydrocarbon systems has been reported; however, very little data are available on natural occurring hydrocarbon systems whose critical temperature is near the reservoir temperature. This appeared to be the case for the fluid studied here; therefore the pressure-volume-temperature data for this system were determined for preqentation. METHOD The PVT data were obtained with equipment similar to hat described by Weinaug and Katz,1 consisting principally of a two-section, double-windowed gauge mounted in a conktant temperature air bath. The procedure followed was essentially that used by Katz and Kurata5 except that a cathetom-eter, reading direct to 0.01 cm, was used to determine the height of each extreme phase limit. The system studied was formed by recombining -.vapor and liquid samples from the first stage separator of the well. Portions of these samples were displaced with mercury into the cell which had previously been filled with mercury. A predetermined amount of the liquid sample was introduced, while an excess of vapor was admitted. The resulting mixture was brought to equilibrium at the condition of the separator during sampling. By adding mercury to maintain the pressure, enough vapor was displaced to give a gas/oil ratio within the cell equal to that produced by the separator at the time of sampling. The remaining material was then considered to be equivalent to the reservoir fluid. An analysis of material in the cell, computed from analysis of vapor and liquid samples and the separator gas/oil ratio. is given in Table I. Table I — Composition of Hydrocarbon System Component Mole Per Cent Carbon Dioxide 0.13 Nitrogen 0.76 Methane 53.91 Ethane 14.20 Propane 9.64 Iso Butane 1.25 Normal Butane 4.29 Iso Pentane 1.12 Normal Pentane 1.87 Hexane 2.72 Heptanes + 10.11 hloleculal. Weight of Heptanes + 178.50

Jan 1, 1951

By R. P. Rothwell

IN January last I published in the Engineering and Mining Journal a table giving, with a considerable degree of accuracy, the production of anthracite coal for the year 1874. At that time it was impossible to give any correct estimate of the production of bituminous coal, for the returns I had been able to secure from such distant and scattered districts were not always forwarded punctually, and the work of -obtaining anything like a true estimate of the coal mined in districts from which I was unable to obtain official returns was both laborious and tedious. As will be seen from the detailed reports furnished herewith, I have succeeded in obtaining tolerably accurate returns of 20,093,704 tons; and upon careful revision by numerous well-informed local authorities, my first estimate of the amount of coal not officially returned to me has grown very considerably; indeed, as I get more information on the subject I find that our bituminous coal production greatly exceeds the amount we have been accustomed to hear it placed at, aggregating as it does, 26,465,704 tons. Mr. Andrew Roy, State Inspector of Mines for Ohio, has reported the production of Ohio at 4,168,445 tons, while his first estimates were but 3,820,000 tons; and similarly, in other cases, the more full the returns direct from the mines the more incorrect do I find all previous reports. I am able now to furnish, not an accurate statement, indeed, but by far the most full and reliable one that has yet been published of our coal production. The amount of labor involved in obtaining this admittedly imperfect report has been simply enormous. In the following tabular statement it will be perceived that Pennsylvania produces nearly one-half of all the bituminous coal mined * Since this paper was read fuller reports from some of the States whose production had been "estimated" have modified the figures given. The most serious error is in California, which produces probably 200,000 tons less than these figures. Oregon and Washington territories also yield smaller amounts than here reported; but these reductions are probably fully compensated by fuller reports from other States that were here underestimated. The correct aggregate amount will not vary much from that here given. Early in 1876 I will be able to give a fuller and more accurate report for the year 1875.

Jan 1, 1875

By F. S. Buffington, Morris Cohen

THERE is little quantitative information available concerning the effect of applied stress, in both the elastic and plastic ranges, on diffusion kinetics. Accordingly, a program has been undertaken to determine the rate of self-diffusion in high purity iron, with the specimens subjected to stress during the course of diffusion. Results are reported here for body-centered cubic iron at a diffusion temperature of 890°C. The iron used was 99.97 pct Fe, the principal impurities being 0.002 pct C, 0.008 pct 0, and 0.02 pct Si. The surface-decrease method of self-diffusion analysis was employed, and Fe55 Mn x-radiation, 2.9 years half-life) was the tracer element. Details of specimen preparation and equipment are given elsewhere.' Disks of the high purity iron, % in. diam x 1/4 in. thick, were annealed at 890°C for 18 hr in dry hydrogen to produce large grains of a ferrite. The faces of the disks were then surface ground, and possible grinding stresses were relieved by annealing at 890 °C for 45 min in vacuum. A layer of radioactive iron 0.00186 cm thick was electroplated on one face of each disk. The self-diffusion coefficient was calculated from the ratio of the radiation intensities emanating from each of these faces, as measured before and after diffusion.' The heating was carried out in a vacuum furnace (10-5 mm Hg) controlled to ±1.5°C. The specimens were loaded in compression between two quartz disks during the diffusion runs by means of a lever system operating through a vacuum seal. Thus one quartz disk was pressed directly against the radioactive face of the specimen, minimizing the vapor loss of radioactive iron. Steady-state creep occurred in all instances where permanent deformation could be detected, but the specimens did not exhibit appreciable transverse barreling until natural strains of 0.2 to 0.3 were attained. Essentially, the diffusion took place under uniaxial stress. The plastic strain in each case was obtained at the diffusion zone by measuring the diameter d there before and after the run: e = 2 In — do Let Du equal the self-diffusion coefficient which would have prevailed at the given temperature if no stress had been applied. This was calculated from the temperature-dependence equation which had been previously determined: —59,800 D, = 6.2 exp ( I sq cm per sec* [I]

Jan 1, 1953

ASIDE from the John Fritz Medal, in which the Institute partici¬pates through its representation on the John Fritz Medal Board, the Institute itself has three major awards to make annually and one special prize for excellence in technical papers, as follows The Robert W. Hunt Medal and Prize, The J. E. Johnson, Jr , Award, the James Douglas Medal, and The Lewisohn Platinum Prize to senior members. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules¬ 1 The award shall consist of two prizes, first of a gold medal, second of a sum of money, a certificate to accompany each prize. The money prize shall not be awarded to -a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side m recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3 A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval.. , 4 The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5 The recipient of the award shall be designated "The Hunt Medallist " This prize is administered by the Iron and Steel Committee.

Jan 1, 1923

By P. Crowther, G. J. Lamprecht

The solubilities of silver, zinc, and cerium in liquid sodium, in the temperature ranges 100 to 270°C, 190° to 550°C, and 120" to 460°C, respectively, have been determined. From the solubility data the heat the entropy the partial molal enthalpy of mixing the excess entropy and the partial molal free energy of solution for the systems Nu-Ag and Na-Zn have been calculated. For the system Na-Ce the observed negative is discussed in terms of the solubility of the oxide Ce2O3. In an earlier publication the results obtained in the study of the solubility of tin' in liquid sodium are presented, as well as the detailed analytical procedures used. 1) REAGENTS Spectroscopically pure metals as supplied by Johnson Matthey and Co, were used to produce the following tracers: 253-day Ag110, 245-day zn65, and 325-day ce141. The tracers were prepared by irradiation in a thermal neutron flux of 4 x 10 13 neutrons cm-2 sek-1. To obtain a uniform amount of the required specific activity, needed for each solubility experiment, the radioactive metal was diluted with the corresponding inactive metal, by melting them together in an inert atmosphere. The liquid sodium used contained 11 ±2 ppm of O,1 determined by the vacuum distillation method.' The oxygen was assumed to be present as the oxide NaD. 2) THE SYSTEMS: SODIUM-SILVER AND SODIUM-ZINC Plots were made of the log of the mole fraction of silver, Fig. 1, and of zinc, Fig. 2, dissolved in the liquid sodium vs reciprocal absolute temperature. The equations for the solubilities, based on the least-squares fit to each plot, are: where Xi is the mole fraction metal dissolved in sodium, T is the absolute temperature, and s is the standard deviation in the value of log Xi. The heats and the entropies lution were calculated from the solubility data by In neither of the two cases was any intermetallic compound formed between sodium and the solute metal as was the case for tin.' Thus, for the silver and zinc systems the pure metal was taken as the reference phase. Since the solids in equilibrium with the liquid sodium were the pure metals, one can calculate the partial molal enthalpy of mixing and

Jan 1, 1969

By Max Roesler

W. L. CUMINGS,* Bethlehem, Pa. (communication to the Secretary+). -In this discussion of Mr. Roesler's paper, I shall follow Kemp in using the term "granite" to refer to the acid rock called syenite by Kimball. Diorite, as I understand it, is the dark basic rock invariably closely associated with the orebodies. The types of rock of intermediate composition, mainly intrusives, are not under discussion. It is difficult for me to conceive that this granite is the ore-bearing agent, for the following reasons: 1. No isolated orebodies in the granite are known. It would seem that if this rock is the mineralizer, some small bodies, or at least patches and small masses of ore so situated would exist. 2. In 1909 the writer conducted explorations on the Pequena and Grande claims about 1 mile north of West Mine No. 5. This work was done after a very careful magnetic survey had shown a large and uniform area of attraction. As exploration progressed, it became evident that in this case the magnetic attraction was due to disseminated magnetite. Much ore of 40 per cent. Fe was found, but very little commercial ore was shown up. This ore was entirely in the diorite and no granite outcrops are near. The occurrence could easily have been described as "ore formation but very little ore." I cannot conceive how a remote granite intrusion could impregnate a diorite mountain with 40 per cent. of Fe, and prefer to believe that this 40 per cent. of iron was in its real home, rather than in a sort of dioritic "boarding house" after having been evicted by granitic parents. 3. The Ocaña mine, which has produced nearly 500,000 tons, shows no evidence that the granite is the mineralizer. This is admitted by Mr. Roesler on p. 1827. 4. I believe it will not be disputed that all the iron-ore deposits extending along the south coast for 60 or 70 miles are of a similar origin. Evidence available at other points might properly be referred to in discussing the article under review. At the La Plata mines, about 60 miles west of Santiago, the writer has also made explorations. No granite is in evidence. At one point in the bed of a creek is a small body of magnetite about 10 ft. long, entirely surrounded by a hard fresh diorite. To me

Jan 3, 1917

By M. E. Straumanis, R. P. Shodhan

LATTICE parameters of molybdenum of various purities are summarized in Table I. The latter shows that the parameter fluctuates between 3.1467 and 3.1475A. The room-temperature expansion coefficient a is also not well-known as values from 4.90 to 5.20 x 10-6 can be found in the literature.=-' It, therefore, seemed appropriate to repeat the measurements under exactly controlled conditions, using high-purity Hilger molybdenum powder (containing 0.0015 wt pct of Fe, 0.005 of Si and traces of other elements) and a 99.95 pct pure Sylvania Electric preparation (containing Cr, Fe, Ni, Si, Sn, and C in amounts of 50 ppm of each and in still smaller amounts Cu, Pb, Mg, and Mn). Of course, both samples could have contained at least 0.01 pct of oxygen in form of a surface oxide. However, oxygen, because of its small solubility in molybdenum, does not influence its lattice constant.g The determinations were made in a cylindrical precision X-ray camera, 64 mm in diam, the temperature of which was controlled within *0.05"C, by inserting it into a special thermostat." To exclude the film shrinkage effect (after the development of the film), the asymmetric film placement method was used." Absorption corrections (e.g., by extrapolation)" were unnecessary because of the use of a thin Li-B-glass fiber (about 0.08 mm in diam) which was fastened to the sample holder of the camera and dusted with the fine molybdenum powder. Cum radiation of the wavelength 1.389350 kX was applied because it produced in 30 min the line (420) having a high Bragg angle of about 81.6 deg. The conversion factor of 1.00202 gave the results in angstroms. To obtain the expansion coefficient a, exposures were made at various temperatures t, see Fig. 1, on at least two films at each temperature. The films were measured with a componator and the lattice constants a were calculated. The expansion coefficient was found from: where a2s is the constant at 25°C and A is the change in a and t. The same equation (knowing a) was used to reduce all the constants obtained at various temperatures to that of 25"C, Table 11. The probable error S507p (at a 50 pct confidence limit) was calculated from the reduced constants:

Jan 1, 1969

By Thomas T. Read

Readjustment of the industrial world to a peace basis after more than 4 years of war will involve many fundamental and far-reaching changes that cannot as yet be clearly foreseen or definitely provided for. Such problems may be subdivided, in the vocabulary of war, into those involving material and those centering about personnel. Of the two, the latter group is the more difficult and obscure, as the factors involved are less clearly understood and the methods to be followed are not yet tested and standardized. When it is said that the market is weak, stocks large, and demand light, every business man understands clearly what is meant and what course he should adopt to adjust himself, so far as possible, to such conditions. But when it is said that the rapid spread of Bolshevism in Europe is a danger to industrial organization in this country, it is difficult to have any assured sense that all that the statement may mean is clearly understood or that the means to be followed to meet such a situation are definitely known. Since Bolshevism is primarily a mental phenomenon and since the rupture it brings about in industrial organization should be prevented, if possible, it is my purpose to restrict this discussion of the activities of the Committee on Industrial Organization to some of its mental aspects, as the chairmen of the sub-committees, from their special knowledge of their own fields, can best set forth recent progress in the lines with which they are especially concerned. The first requisites of success in industrial organization, as in the biological organism of which it is the social counterpart, are unity of purpose and coordinated activity. Typical good and bad examples of this' are the relative parts that the United States and Russia have played in the great war. These two factors are primarily mental, and it is not difficult to view the mental aspects of all problems of industrial organization as the most important ones. Unless we can attain unity of purpose and coordinated activity in industry, the provision of comfortable homes at reasonable rent, the assurance of steady work at good wages, the elimination of industrial accidents, and provision against want in old age or in case of disability will have brought us no nearer to our real goal.

Jan 1, 1919

By H. G. Botset

A KNOWLEDGE of the water content of producing sands is becoming of increasing importance to the petroleum industry. It is now a generally accepted fact that practically all oil sands contain some free water. Recent experiments1 have shown that an appreciable fraction of the pore space of a sand may be filled with water while oil production from this sand is water-free. Crowther and Haines,2 in experiments on electro-endosmosis in soils, reported that there was no endosmotic flow of water when the moisture content of the soil was 14 per cent or less, indicating that the moisture content of the soil below 14 per cent was held by dif-ferent forces than the water content above this value. This result is confirmed qualitatively by Dunlap,1 who found that "as the volume of water in the voids exceeds approximately 15 per cent of the pore volume, the permeability of the core to kerosene is markedly reduced." The author3 has also found in other experiments that the gas flow through a water-saturated sand reaches essentially 100 per cent when the pores of the sand still contain from 10 to 15 per cent water. The velocities of the flowing fluid in the experiments cited were comparatively high, so that in practice one may expect, at lower fluid velocities, an even higher moisture content of the sands with water-free oil or gas production. Thus a knowledge of the water content of oil-field sands becomes of con-siderable importance in estimating petroleum and gas reserves, and effi-ciency of fluid recoveries from depleted reservoirs. Rapid and reasonably accurate methods of measuring the water content of sand cores have not been described so far in any literature that has come to our attention.4 The method described below is devel-oped from methods that have been used for some time to measure the water content of alcohols.5,6,7 It is an application of the fact that in the presence of certain organic liquids such as kerosene, carbon tetrachloride, xylol, etc., water and alcohol are only partly miscible. This relation-ship has been used for some time in the study of gasoline-alcohol mixtures where the presence of small quantities of water affect the solubility of

Jan 1, 1938

By B. D. Cullity

GOLD and beryllium form an intermediate phase composed of the two metals in equal atomic proportions and having the formula AuBe. According to Winkler,1 this phase probably exists in two modifications: beta, stable below about 600°C, and alpha, stable between 600°C and the melting point, about 740°C. Only the low- temperature beta form will be considered in this paper. EXPERIMENTAL PROCEDURE The gold used had a fineness of 999.75 to 999.85, balance mainly silver, and the beryllium purity was better than 99.8 pct. AuBe was prepared by melting the constituents in a beryllia crucible in an evacuated induction furnace. After melting and thorough mixing, the alloy was allowed to solidify in the crucible. No difficulty was encountered in obtaining a homogeneous ingot. Both chemical analysis and microscopic examination of the ingot showed that the alloy was essentially one phase, containing 50 at. pct gold. The alloy was quite brittle and powder samples could easily be pre- pared by grinding in an agate mortar. The X-ray diffraction patterns were made with CuK-alpha radiation in a Debye-Scherrer powder camera 57.3 mm in diameter. The film was placed unsymmetrically in the camera in order to afford a basis for am-shrinkage corrections. A sample homogenized at 5o0°C gave the same diffraction pattern as a sample taken from the as-melted ingot. GENERAL RESULTS The diffraction pattern of AuBe was readily indexed on the basis of a simple cubic lattice with ao = 4.659 ± 0.001kX. If the unit cell is assumed to contain four AuBe "molecules," the calculated X-ray density is 13.46 grams per cc as compared with the measured density of 13.55 gm per cc. The only missing reflections in the dsraction pattern are (100) and (220) (see Table I). Since these missing reflections are not those characteristic of body or face centering, the lattice of AuBe must be simple cubic. To locate the positions of the atoms within the unit cell, two possibilities had to be considered: I. The structure was disordered and there were eight positions to be filled by an "average" gold-beryllium atom. That the structure was disordered seemed unlikely since the lattice parameter did not vary with composition in alloys containing some- what more and somewhat less than 50 at. pct gold, indicating a fixed composition for AuBe.

Jan 1, 1947

By B. D. Cullity

Gold and beryllium form an intermediate phase composed of the two metals in equal atomic proportions and having the formula AuBe. According to Winkler,' this phase probably exists in two modifications: beta, stable below about 600°C, and alpha, stable between 600°C and the melting point, about 740°C. Only the low-temperature beta form will be considered in this paper. Experimental Procedure The gold used had a fineness of 999.75 to 999.85, balance mainly silver, and the beryllium purity was better than 99.8 pct. AuBe was prepared by melting the constituents in a beryllia crucible in an evacuated induction furnace. After melting and thorough mixing, the alloy was allowed to solidify in the crucible. No difficulty was encountered in obtaining a homogeneous ingot. Both chemical analysis and microscopic examination of the ingot showed that the alloy was essentially one phase, containing 50 at. pct gold. The alloy was quite brittle and powder samples could easily be prepared by grinding in an agate mortar. The X-ray diffraction patterns were made with CuK-alpha radiation in a Debye-Scherrer powder camera 57.3 mm in diameter. The film was placed unsym-metrically in the camera in order to afford a basis for film-shrinkage corrections. A sample homogenized at 500°C gave the same diffraction pattern as a sample taken from the as-melted ingot. General Results The diffraction pattern of AuBe was readily indexed on the basis of a simple cubic lattice with ao = 4.659 + 0.001kX. If the unit cell is assumed to contain four AuBe "molecules," the calculated X-ray density is 13.46 grams per cc as compared with the measured density of 13.55 gm per cc. The only missing reflections in the diffraction pattern are (100) and (220) (see Table I). Since these missing reflections are not those characteristic of body or face centering, the lattice of AuBe must be simple cubic. To locate the positions of the atoms within the unit cell, two possibilities had to be considered: I. The structure was disordered and there were eight positions to be filled by an LCaverage" gold-beryllium atom. That the structure was disordered seemed unlikely since the lattice parameter did not vary with composition in alloys containing sornewhat more and somewhat less than so at' pet gold, indicating a fixed composition for AuBe.

Jan 1, 1947

By Raymond Mancha

TO determine the optimum inside dimension of an airshaft, it is necessary to strike the proper balance between the cost of power for air friction and turbulence losses within the airshaft, on the one hand, and the cost of sinking the airshaft, on the other. An airshaft larger than necessary is extravagant because the increased amortization rate exceeds the reduction in power cost. Conversely, an airshaft smaller than is needed wastes more power than can be justified by the corresponding reduction in amortization rate. The airshaft power is a function of the air volume Q cu. ft. per min. and the air-pressure drop p in. water gauge across the airshaft. † The airshaft pressure drop is calculated by the formula: R X l X O X Q2 P= 5-2 X A3 wherein R is the air-friction coefficient for the portion of the airshaft 1 ft. deep, 0 ft. in perimeter and A sq. ft. in area, when passing an air volume of Q cu. ft. per minute. The airpower w kw. dissipated within the airshaft is computed by the formula: w= 0.746Q X P 6345 With a combined over-all unit efficiency of the fan and drive of E per cent, the air-shaft power requirements become W = 100w There are 8760 hours per year, so with energy at I cent per kilowatt-hour the annual cost per kilowatt for continuous operation is $87.60; therefore, with energy at C¢ per kw-hr. the annual airshaft power cost MI dollars per year becomes: M1 = 87.60W X C which, expressed by the component parts, becomes: M1 V 5.2X4' / XQ Z 0.746 X 100 X 87.60 X C V 60 X E ) The amortization rate a dollars per year per dollar invested includes both depreciation and interest on the investment. These in turn involve the expected useful life of the airshaft and available molletary interest rate. For the purpose of this discussion the cost of airshaft sinking is assumed to comprise a fixed move-in charge Y dollars, which covers the cost of transporting, erecting and removing the shaft-sinking equipment and is independent of the air-shaft size. Also, it is assumed that the cost of shaft lining, if any, is fixed at $X per cu. yd. of lining material and that excava-

Jan 1, 1947