Search Documents

By E. L. Anders

The Mile Six pool is located on the La Brea-Parinas Cullcession of International Petroleum Co., Ltd., in northwestern Peru on the west coast of South America. The reservoir pressure in this pool has been maintained within 200 psi of its initial value throughout its history, and gravity drainage has played an important role in the production behavior. It has now produced 95 per cent of its estimated ultimate recovery. It is estimated that this interesting oil pool will ultimately produce 67 per cent of the initial oil in place and that the resulting residual oil saturation may be as low as 19 per cent of the pore volume (29 per cent of the hydrocarbon pore volume). An evaluation of reservoir rock and fluid characteristics and ultimate oil recovery is presented. INTRODUCTION This study of Mile Six pool was made to evaluate its performance according to latest available information. The production performance of this pool has been discussed in various articles in the past. and the reported behavior has been used as an example for application of computation procedures for gravity drainage depletion' and as an illustration of field behavior under gravity drainage or expanding gas cap drive. There have been wide variations in reported values of initial oil in place, reservoir oil volume factor. connate-water sauration, volume of effective sand, and ultimate recovery because of the paucity of reliable basic data. These various factors have been determined as accurately as practicable with the latest available information, and this evaluation is presented herein. The production history of Mile Six is an excellent example of gravity drainage depleion with effective pressure maintenance by gar injection. GENERAL Mile Six pool was discovered by cable-tool drilling in November. 1927. when well 1996 was completed in the Parinas sand. After slow development with cable tools and sporadic production. the pool was opened to continuous pro(iuction in November. 1933. and develpment was completed with rotary rigs. Pressure maintenance was started in December, 1933. by returning gas to upstructure wells. Most of the development was 'completed by 1937, but some additional wells were drilled in the period 1939-1947. and several old wells were deepened. A total of 46 oil and gas wells and 4 dry holes were drilled on approximately 7-acre spacing. Of the producers. 21 are now flowing. 2 are pumping. 44 are gas input wells. 3 are abandoned. I is a gas well shut in. and 15 are shut in because of non-commercial production or high gas-oil ratio. The locations of all wells are shown on the map of Fig. I. Total oil production on Dec. 31. 1952, was 30,867,373 bbl: cumulative gas production was 22,023,777 Mcf; and 26,410,946 Mcf of gas had been returned to the reservoir. These figures do not include oil and gas lost ill a blowout in January. 1940. GEOLOGICAL DESCRIPTION Mile Six pool is located on the northern end of a structural spur projecting from the La Brea-Negritos uplift.' The spur is probably a reflection of a basement structure. It plunges gently to the north, i broken into a complex series of fault blocks. and contain.; the Verdun Alto. Section Sixteen. and Mile Six pools. The Parinas handstone (lower Eocene!. which is the producing formation in Mile Six. occurs at an average depth of 2,200 ft in the pool and dips north and east at from 15' to 20". The pool covers an area of approximately 350 acres. Mile Six is downfaulted about 600 ft from Section Sixteen pool to the soutb. and a major fault forms its western boundarv. The north and east boundaries are formed by the intersection of the sand top with the water-oil contact which occurs at approximately 2.440 ft subsea. An original gas-oil contact probably existed at about 1.875 ft subsea. Fig. 1 presents the latest structural interpretation of the pool. and Fig. 2 is an isopach map showing thickness of the total Parinas formation above the original water-oil contact. The heavy lints of Fig. 1 are contours on the sand top, and the fine lines are contours on the fault planes. This type of straight-line structural map was developed 1)) International's geologists to reflect structural conditions where the bedding planes dip and have no curvature. 'The La Brea-Parinas Concession is highly faulted by normal fault.. The beds are flat wherever exposed. The Parinas formation is approximately 635 ft thick. and it is etimated that 62 percent II the formation is effective sand. The original oil zone was about 565 ft thick. Fig. 211 presents an electric log showing typical Parinas sand development ill Mile Six pool. The Parinas band in Mile Six i. a well-sorted. medium- to-coal-se-grained. cross-bedded sand with minor lenses of shale and small lenses and pockets of pebble conglomerate. The sand grains are subangular to rounded and consist chiefly of quartz with feldspars. biotite hornblende, and augite as accessory minerals. Because of faulting of the Parinas- formation to the east and north of the pool. there is probably l possibility of a significant, natural water drive in Mile six. The faults within the pool. as indicated in Figs. 1 and 2. are of smaller disI,laceInent and seem to act only , partial barriers to fluid movement within the reservoir. RESERVOIR CHARACTERISTICS Core analysis data are available from five wells. The data were obtained from three wells (Nos. 3401. 3586 and 3719) at the time of their completion and from well 1996 when the original liner was sidetracked and the well was deepened ill 1946. Data from well 2779 were obtained in 1943 from old cores taken when the well was deepened in 1934. From these core analyses. the average porosity was estimated to be 22.6 per cent. and the average permeability to dry ail. was estimated to be 780 and Measured productility indices varied from 3.1 to 71.4 B/D per psi differential. Specific productivity indices varied approximately from 0.1 to 0.3 B./D per psi per ft of sand.

Jan 1, 1953

By Milton R. Pickus, Earl R. Parker

THE modern theories of creep¹-4 in general have been based upon the concept of generation and migration of dislocations, with the generation process normally assumed to be rate controlling. The theories are generally deficient in that they fail to take into account many factors that are known to influence creep. The influence of the state of the surface of the test specimen has been almost completely overlooked; yet the present report shows that the nature of the surface may, in certain cases, govern the creep characteristics of a specimen. In the period since Taylor" applied the concept of dislocations to a study of metals, a school of thought has developed that closely relates the plastic deformation of metals to the generation and migration of dislocations through the crystal lattice. It might be expected that the thermal energy required for the generation of a dislocation would be different from that for migration of the dislocation through the lattice. Furthermore, the activation energy for generation would be expected to vary for different parts of the solid metal. It has been predicted that dislocations would be generated most easily at external surfaces, but could also be activated at certain internal surfaces such as grain or phase boundaries. Within the body of the metal a range of values for the activation energy might be expected because of different degrees of disorder at such regions as grain boundaries, impurities, and second-phase particles. The particular value of the activation energy that was rate determining could then depend on the specific conditions of a test. If, for example, the surface atoms were by some means constrained, the generation of dislocations in the body of the metal might become the important factor. On the other hand, other conditions may favor generation at the surface. It is possible then that the creep behavior may not be completely determined by the inherent properties of the metal. Even the environment in which a test is carried out could have a significant effect. In fact it is conceivable that in order to obtain the maximum creep resistance from a given alloy, the surface atoms must be so constrained that the activation energy for generating dislocations on the surface is at least equal to that required for generation in the body of the metal. On the basis of such considerations, and in view of the limited number of publications discussing this subject, it seemed that an investigation of the influence of the state of the surface on creep might yield information of both theoretical and engineering interest. Experiments on single crystals, demonstrating a variation in the mechanical properties due to alterations in the surface layer, have been reported by several investigators.6-13 he results of these experiments have been briefly summarized;14 consequently, the earlier work will not be reviewed here. As an example of these findings the observations of Cottrell and Gibbons may be cited. They reported the critical shear stress of a lightly oxidized cadmium single crystal is greater by a factor of 2½ than a specimen with a clean surface. Materials and Methods Single crystals M in. in diam and 8 in. long were prepared from Horse Head Special zinc, melted under an atmosphere of helium in a large pyrex test tube, and drawn up into a long ½ in. diam pyrex tube by means of a vacuum pump. The cast zinc rods thus produced were cut into convenient lengths and sealed in evacuated pyrex tubes. Single crystals were grown by gradual solidification of the remelted rods. Cleaving the ends of the single crystal specimens chilled by liquid nitrogen proved a simple method for determining orientations from the exposed basal plane from the markings left on the cleaved surface that gave the slip directions with sufficient accuracy for the experimental work. The specimens chosen for the experiments were those having the angle between the basal plane and the specimen axis within the range of 15" to 65". Since zinc single crystals are quite delicate, it was necessary to devise an appropriate method of gripping the specimens in order to suspend them in the furnace and apply the load. Stainless steel collars were prepared having an inside taper, the smaller end of the taper being of such a size that the specimen could just pass through freely. The tapered hole did not extend the full length of the collar; a sufficient thickness of metal remained so that a hook could be attached to provide a means of applying the load and suspending the specimen. One of the collars was slipped over the upper end of a specimen which was supported vertically in a steel jig. The collar was then heated electrically until the end of the crystal melted and filled the collar with molten zinc. At this point the application of heat was discontinued, whereupon the molten zinc quickly solidified, due to the chilling effect of the jig. The specimen was then inverted and the second collar applied in a similar manner. The jig served several purposes: limiting the length of specimen that was melted, providing excellent alignment of the collars with respect to the specimen axis, and protecting the specimen from mechanical damage. Once the specimen was suspended in the furnace and loaded, it was desired to accomplish the surface treatment with a minimum of disturbance of the specimen. Around the specimen was a long pyrex tube, the upper portion of which was approximately 1 in. in diam, and in it was a copper coil of such a diameter to fit snugly against the tube. A specimen, approximately ½ in. in diam and 4 in. long, was suspended by means of a stainless steel rod so that it hung within the copper coil. The lower portion of the glass tube was approximately ¼ in. in diarn, and passing through it was a 5/32 in. diam stainless steel rod which hung from the lower specimen collar. This portion of the glass tube and the stainless steel rod extended through the bottom of the furnace. A T-connector, with suitable packing, was attached to the lower end of the stainless rod to provide a water-

Jan 1, 1952

By A. L. Bailey, B. A. Landry

W. W. ANDERSON and G. E. KELLER*—We want to compliment the authors on this very thorough paper. It gives information which the coal industry has needed for some time. We hope that the additional information which the authors are collecting will he available shortly. The mixing and riffling procedure that was followed for experimental purposes is obviously not practical in routine float-and-sink testing because of the particle size degradation which would result in handling the sample so many times. It is important to obtain our tloat-and-sink fractions with a minimum amount of handling of material. A statement is made in the paper (p. 80) that "the variable most likely to affect the size of sample required to meet a given preassigned accuracy would be the state or degree of mixing of the coal." We agree that this is a large factor, but do not believe it is the most important factor. Our own opinion is that the most important single factor governing the total gross weight of sample that must be collected is the percentage of the weight of material in the smallest fraction that results from the screening and float-and-\ink operations. In other words, size of sample is governed by the total number of fractionations that must he made, and the distribution of material within the fractions. We can imagine a coal with perfect mixing, but with such a small amount of material in some float-and-sink fraction in one of the coarse sizes that a much larger sample would have to be taken than would be the case with very poorly mixed material, but with a large percentage of coarse material more evenly distributed in all float-and-sink fractions. Our own observation of many float-and-sink tests that we have run in our own organization on many types of coal is that the size of sample that must be used on fine size float and sink is governed more by the requirements for weight of material to be used for analysis in the laboratory than by weight of material necessary to obtain accurate float and sink percentage of weight values. In other words, it is our opinion that very small samples can be used for float-and-sink fractionation in the fine sizes, but that accurate analysis of the fractions will depend on a larger weight of sample being pulverized for the laboratory than is necessary to establish the float-and-sink distribution with respect to weight. A. L. BAILEY and B. A. LANDRY (authors' reply)—The authors thank Messrs. Anderson and Keller for their comments based on long experience. It is agreed that the involved mixing and riming technique used may be disadvantageous from the standpoint of degradation. Fortunately, the paper does point out that the extended riming was unrewarding in causing further mixing. Two large unknowns remain, however: (1) how much of the mixing from the presumed highly unmixed state in the bed was achieved toward the random state during blasting, loading, transportation, screening, and further transportation to the point where the gross sample was taken, and (2) how much of the mixing took place during the preparation described preceding riming. As has been pointed out by one of the authors.6 the degree of mixing has a very large effect on the size of sample required and there are still too few experimental data to show at what stage of coal handling most of the mixing occurs. The discussion states that the weight of material in a screened fraction, or in a float-and-sink fraction, is more important than the mixing factor. We do not believe that these factors are comparable in this instance inasmuch as our purpose was to give minimum sampling requirements to achieve a preassigned accuracy in the percentages of float, middlings, or sink, and nothing more. The gross sample had already been screened and no further division by screening was made or contemplated; also, it was not intended that the middlings and sink fractions would necessarily be adequate for percentage ash or other determination. In other words, the sample obtained by the method outlined is not intended for washability studies but only for preparation plant control. Further experimental work has been done, since the paper was prepared, to investigate the effect of increasingly larger top and bottom sizes on the variability of float, etc., of a double-screened coal from Western Pennsylvania. Results will be published and eventually attention is to be given to the preparation of sampling specifications. E. H. M. BADGER*—I should like the authors to explain more fully the fundamental assumptions on which their Eq 4 is based. The equation is of the form s2 = p(l - p) which is the usual expression for the (standard deviation)2 when the chance of finding a particular kind of particle in the sample is proportional to the number fraetion, p. But instead of the number fraction, the authors have used the weight fraction, WF/W. The chance of finding a particular kind of particle in the sample can only be proportional to the weight fraction, if the average ?eig?ts of all kinds of particles, that is, float, midlings, or sink, are the same. Surely a much more justifiable assumption would be that the average volumes of the particles are the same, and, if this is so, Eq 4 would not be true. This may be demonstrated as follows: Let be the weight fraction of float, middlings, or sink, dl the density of this fraction, and d2 the density of the rest of the coal. Then assuming that the average volumes of the pieces in the three classes are the same, the number fraction, p, is given by ? P = d1/l-?/d2 + ?/d1 = ?d2/d1 + ?(d2-d1) The weight fraction, w, in terms of p is given by ? = pd1/(l-p)d2 + pd1 = pd1/d2 + p(d1-d2) _____ [61

Jan 1, 1950

By C. S. Barrett, D. B. Masson

Martensitic transformations have been found in AgCd both upon cold-working at room temperature and cooling to lower temperatures. The crystal structures of the transformation products were found to be close-packed hexagonal in the first case and or-thorhombic in the latter. The transformation characteristics also were studied. Similar treatment of AuZn alloys failed to yield any transformation. THE literature on martensitic transformations of body-centered cubic metals and alloys indicates widespread instability of this structure at low temperatures, a tendency which merits further study. The body-centered cubic ß-phase of CuZn, for example, when it contained less than 42 wt pct Zn, was found by Greninger and Mooradian' and others' to transform on cooling to subzero temperatures to a phase that was tentatively considered to be tetragonal. Further work by Massalski and Barrett" demonstrated that cold work at low temperatures causes a partial transformation of ß CuZn of higher Zn content. The structures of the strain-induced transformation products were found to be different from those induced by simple cooling. Another well-known martensitic transformation among body-centered cubic phases is that of ß AuCd, first studied with X-rays by Olander,' then very thoroughly by Chang and Read.5,6 Here again transformation was found to occur both as a result of cooling and of strain. The alkali metals Li and Na, as well as certain Li-Mg alloys, also undergo transformation from their normal body-centered cubic structure, both on cooling and on cold-working. The phase AgCd, the subject of the present report, should be expected to behave quite similarly to CuZn for a number of reasons. It is the chemical analogue of CuZn, silver being directly below copper and cadmium directly below zinc in the periodic table. The size factors (percent difference in size) of the atoms, possibly a consideration in the stability of the ß-phases, are +3.1 in AgCd and + 4.2 in CuZn. Likewise the relative electronegativities of the two pairs of metals are about the same, CuZn possessing an electronegativity difference of 1.0 and AgCd one of 0.8. These values are from a table of electronegativities given by Darken and Gurry." The phase diagrams of the two systems around 50 atomic percent are similar, both possessing a disordered body-centered cubic phase, ß, at high temperatures and an ordered bcc phase, ß, at room temperature; however, the ß and ß' phases of AgCd are separated by a hexagonal phase, [, stable in the range 220-440oC, which has no analogue in CuZn. There has been confusion in the literature as to the structures of the ß' and [-phases. The phase diagram in the ASM handbook'" has the structures of the two phases interchanged; however, Hansen" reports the correct relative positions and Muldawer" verified that ß', the low-temperature phase, is body-centered cubic. Work by the present authors also

Jan 1, 1959

By G. G. Brown

Enthalpy-entropy diagrams are presented for natural gases of 0.6, 0.7, 0.8, 0.9, and 1.0 gravity over the pressure range of 5 to 10,000 Ib. per sq. in. and temperature range of 32º to 700°F. The charts indicate directly the work requirement and temperature rise for adiabatic compression or temperature change for free emansion of natural eases. Computation and Uses of Charts The Mollier diagram (Fig. 4), in which the enthalpy (heat content) is plotted against the entropy with lines of constant temperature, pressure,, and in some cases volume, has been found most convenient when dealing with the compression, expansion, and flow of fluids. In dealing with the flow of fluids, the sum of the increase in the enthalpy, AH, plus the increase in kinetic energy, AM —, plus the increase in potential energy, ?MZ, representing the total increase in energy of the fluid in flow, is equal to the sum of the heat q, and work added, —w, to the fluid while flowing between the entrance and exit of the flow system. AH + AM— + ?MZ = q-w [1] In cases where there is no significant change in potential energy or in kinetic energy (velocity), it follows that the increase in enthalpy is equal to the total energy supplied to the fluid. Under such conditions' the changes in the property of the fluid as it flows through a throttling valve, choke, or any other similar arrangement, may be read directly from the enthalpy-entropy diagram by following a horizolltal line between the known pressures' When compressing Or expanding a gas by means of a Or or engine in which no heat is added to or subtracted from the gas, but only work done, the changes in the properties of the gas may be determined along a vertical line of constant entropy between the entering and exit pressures. The power required for the compression of the gas may be readily determined by converting the increase in enthalpy into the desired units. The enthalpy-entropy diagram for natural gases is to the gas engineer what the steam diagram is to the steam-power engineer. For this reason it would be extremely convenient if a reasonably satisfactory enthalpy-entropy diagram could be prepared as a function of the gravity of the gas. A careful study of the known properties of natural gas indicate that this is possible. The effect of temperature upon the enthalpy at constant pressure is expressed as the "heat capacity" or "specific heat" of the gas. The best available data for natural and petroleum refinery gases indicates the relationship shown in Fig. I. From this it is clear that the specific heat of natural gases is a function only of the gas gravity and the temperature at atmospheric pressure. The effect of pressure on the enthalpy of natural gases is dependent upon the pressure-volume-temperature relationships,

Jan 1, 1945

By Margaret G. Scroger, Luke L. Y. Chang, Bert Phillips

Using the sealed-system technique, isothermal sections at 1000°, 1400°, and 1700°C for the system Co-W-O hare been determined. The equilibrium data were obtained by microscopic and X-ray diffraction examination of samples winch had been equilibrated in pellet form fit sealed capsules and subsequcelly quenched. The only ternary phase in the system is CoWO, which mells congruentlly at approximately 1280°C. At 1000°C, this ternary phase exists in equilihrinm with all the allows and oxide compounds in the hounding binary systems. At 1400°C, liquid forms in thin oxygen-rick region near the CoWO4 composition and only one phase assemblage in the system (W + WO2 + H'5CV7) contains no In order for tungsten to be used to its full potential as a refractory metal. it is necessary that coatings be developed which will preclude oxidation of the metal. It is true that coatings now in use do protect tungsten for short periods at temperatures near 1700 °C. but no coating has been developed which protects adequately at or above this temperature where the use of tungsten is most required. This situation exists despite the great effort in recent years to develop such coatings. and it has become evident that success in this area can be achieved only after a more fundamental knowledge of the thermochemical and therrnophysical propertics of tungsten oxidation and tungsten -metal oxidation is obtained. In our 1aboratories. a project liclrriel. At 1700°C, tungsten is the ouly solid phase which is stctble, and a large range of compositions melt to two liquids, one metallic and one oxidie. The sealed-system method of etjuilibra lion prevents the determination of the partial pressure of oxygen and the total gas pressure orer the condensed phases at equilibrium. This data is not available and can be obtained only by some other method. We can generalize on these unknowns and indicate that both partial pressure of oxygen and total pressure of the gas phase must increase as compositions change from the W-Co binary toward the oxygen apex and as temperatures increase. has been initiated which is directed at providing some of this fundamental information through a study of metal-tungsten-oxygen reactions and equilibria and the properties of any intermediate phases which result. This paper is based on a part of this program in which the system Co-W-O was studied between 1000° and 1700°C. I) RELEVANT INFORMATION FROM THE LITERATURE A) The Notable Lack of High-Temperature Work on Metal-Tungsten-Oxygen Systems. It should be pointed out that there has been no published report (of which we are aware) which deals with the study of a metal-metal-oxygen system at 1700°C. Also, there has been no report on a complete metal-luugsten-oxgen system at any temperature. As a matter of fact. before this program started. The

Jan 1, 1965

By J. W. H. Clare

An equilibrium isotherm at 550°C is given for ternary alloys rich in aluminum containing 0 to 15 wt pct Cr and 0 to 20 wt pct Mn. Phases encountered are: aluminum solid solution; stable temary compound G; and MnAl8,. In addition, a limited number of alloys were annealed at 450°C to check for differences from the 550°C isotherm. These experiments limited the composition of the G phase at 550°C and further experiments established that the G Dhase is not stable above 590 ± 1 °C. RAYNOR and Little1 established several equilibrium isotherms using aluminum-rich alloys containing up to 5 pct of the elements chromium and manganese. These isotherms showed that, in addition to an a solid solution and the two binary intermediate compounds 8 and MnAl6, a stable ternary compound ex-isted in the system. This phase was called the G phase because of its ghostly appearance in micro-sections. Little, Raynor, and Hume-Rothery2 found a similar phase in binary aluminum-manganese alloys and, as a result of their experiments, concluded that the G phase was a metastable phase existing in the aluminum-manganese system. This phase was stabilized by the addition of chromium. The constitutional work of Raynor and Little,' although showing the existence of the G phase in the aluminum-chromium-manganese system, did not establish precisely the composition limits of the phase or the temperature above which the phase became unstable and disappeared from the system. The work described in this paper was undertaken to provide this information. An examination of the previous work' showed that an isotherm at 550°C would provide the required data regarding composition in the shortest possible time, as the (a + G) phase field narrows considerably at higher temperatures. The same work showed that the G phase ceased to exist between 580° and 595°C. A more precise estimate of the transformation temperature would therefore be obtained by annealing selected alloys at successively higher temperatures beginning at 580°C. EXPERIMENTAL PROCEDURE 1) Materials Used—The experimental alloys were prepared from four master alloys containing 15.00 w pct Cr, 15.28 wt pct Cr, 19.80 wt pct Mn, and 19.38 wt pct Mn which were made from super-purity aluminum, electrolytic chromium, and electrolytic manganese. The aluminum was of 99.996 pct purity, the principal impurities being copper, iron, and silicon. The chromium and manganese were 99.9 pct pure, the principal impurities being antimony, calcium, and magnesium. 2) Preparation of the Experimental Alloys—The alloys were prepared in 20-g quantities by melting together the requisite amounts of master alloy and aluminum in an alumina-lined crucible and, after thorough stirring with an alumina rod, cast into a cold copper mold to give ingots 1/4 in. in diam and 3 in. in length.

Jan 1, 1960

By L. F. Coffin

Monotonic tension and controlled cyclic-strain tests have been conducted on an annealed steel at various strain rates and temperatures in the weep range. Evidence of a strain-induced precipitate reaction abozle 500°C was determined from pronounced cyclic-hardening effects, increase inflow stress, inter granular fracture, drastic decrease in low-cycle fatigue resistance, and loss in tensile fracture ductility, as well as through electron-microscopy examination. It was found that strain rate as well as temperature had a pronounced effect on these observations. A parameter of the form P = T(7.95 - log ip) was determined, which was directly related to the ductility, defined either as the true strain at fracture in the case of simple tension, or as 2N 1/2 ? E p in the case of cyclic plastic strain. A highly satisfactory comparison of the cyclic life as measured and as computed from the ductility predicted by this parameter was obtained for a range of temperatures from 400° to 650°C and for crosshead speeds of 0.002 to 0.2 in. per min. MANY metals subjected to sustained loading at elevated temperatures derive resistance to creep from solid-state reactions of various alloying constituents. These reactions can be many and varied, and occur as a consequence of time and temperature according to reaction-rate principles. Strong evidence exists that many of these reactions are influenced by plastic strain, the argument being put forth that dislocations act as sites for nucleation and growth for the new phase.' Many examples can be cited where plastic strain during transformation influences the structure, and as a consequence affects the properties.2 The low-alloy steels serve as particularly good examples for investigating the effect which aging reactions have on resulting properties. Alloying elements such as carbon and nitrogen, and carbide formers such as manganese, chromium, molybdenum, and so forth, can, by the particular aging reaction which occurs, produce strengthening effects at various temperatures, and so endow strength to the alloy over a broad range of temperatures. These effects have been systematically studied by Glen both during creep3 and for constant strain-rate tension testing.4,5 The work of Glen is of considerable interest in connection with the present study, particularly in regard to the effect of various alloying additions on the true stress-strain curve and on fracture ductility at various elevated temperatures. He has shown that strain-age hardening occurred during plastic straining, which was quite specific both to the temperature of the test and to the alloying element involved. When strain-age hardening was noted at a particular temperature, a .minimum in reduction of area was also obtained. Provided the temperature for the minimum reduction of area exceeded 300°C, all minimum ductility fractures were found to be inter-crystalline in nature. For carbon steels containing molybdenum, two minima in reduction of area were noted, one occurring at 200° to 250°C, the precise temperature depending on the percentage of molyb-

Jan 1, 1964

By Jerome F. Kuzmick

Many investigations have been made on the effect of the variables of pressure, sintering temperature and sintering time on the physical and microstructural charactcristics of metal-powder compacts. Severa1 such investigations have indicatcd that pressure is the least important of these three factors in an attempt to secure a dense. strong compact by a simple coltl-pressing and sintering procedure. However, it was felt that a further study of the effect of pressure on pressed and sintered metal powder compacts might prove interesting, for the following reasons: In work done in the past on the effect of pressure, temperature. arid time, the, metal-powder compacts were subjected to long sintering periods, and temperatures right up to the melting point of the metal were applied. It was thought that pressure might exert a more profound effect under short-time simtering and within narrower ranges of temperature. such as normally would be applied in large-scale production of metal-powder parts. 2. It was hoped that something further might be learned of the nature of the bond in pressed and sintered metal-powder compacts. 3. It was thought that interesting infor mation concerning the work-hardening effect of pressure on the crystal structure. of sintered metal-powder compacts would be obtained. Procedure Rectangular bars, 2 by 1/2 by 1/4 in. were molded from the following metal powders: Atomizcd till powder, 325-mesh Atomized aluminum powder, 325-mesh Reduced copper powder, 100-mesh Electrolytic iron powder, 100-mesh Atomized 70-30 brass powder, l00-mesh The, till powder was molded at various pressures up to 40 tolls per sq. in. This was the maximum, because at higher molding pressures there was considerable extrusion of tin into the die wall, jamming the die plungers. The tin specimens were not -in tered, as this phase of the work was- done merely to see how much a very sold metal could be compressed. The aluminum powder was compressed at various pressures up to 50 lons per sq in. Higher pressures could not be used because of extrusion into the die wall The compacts were sintered one hour at 000 in pure dry hydrogen. The copper powder was molded at vari-ous pressures up to 96 tons per sq. in. One set was sintered at 750°C., another at 050 C. for one hour in pure dry hydrogen. The electrolytic iron powder was molded at various pressures up to 00 tons per sq. in. and sintered, one set at Soo°C and one set at 1300°C for one hour in pure dry hydrogen. Extra 325-mesh specimens were also prepared to study the effect of reduced particle size on grain structure. The brass powder was molded at various pressures up to 96 tolls per sq. in. and silltered for one hour. one set at 65o°C. and one set at 800°C, in pure dry hydrogeu.

Jan 1, 1945

By J. Mizrahi, A. M. Baniel, A. Mitzmager, S. Star

This article gives an account of the latest developments in the use of TBE for sink-float separation of silicate minerals. A number of minerals for which the process has been tested and found suitable are reviewed. Specific examples are discussed in relation to the particular problems of sink-float separation and recovery of TBE as compared with non-silicate minerals. The economic aspects are outlined. Silica and silicates comprise the most common and abundant group of minerals, and since they are present in variable amounts in most ores, they constitute an appropriate subject for the review and discussion of the recent developments in the use of TBE for mineral concentration. The silicates considered as a group have an extremely wide range of chemical and physical properties. Some of these properties, which are common to all minerals, are of importance to concentration by TBE and are discussed in some detail in this paper, as well as the development of methods and apparatus for concentration and recovery of TBE and several examples of concentration of silicates. PROPERTIES OF MINERALS WITH RESPECT TO CONCENTRATION BY TBE The properties considered as most important to concentration by TBE are specific gravity, structure, surface and shape. The specific gravity of a mineral is a fundamental property and is constant between very close limits for the same species of different sources if particles are pure and free from cavities or cracks. In many species, however, solid inclusions and changes in chemical composition due to replacement of elements cause variations in the specific gravity. The plagio-clase series of feldspars between albite and anorthite illustrate this point (specific gravity from 2.60 to 2.77). Fig. 1 shows the specific gravity distribution of some of the common silicate minerals.' The highest specific gravity is about 4.7 (zircon) and the lowest is 2.0 (sepiolite), with most of them ranging between 2.6 and 3.5. Although most of the silicates given in Fig. 1 are found as constituents of rocks, those generally considered as rock making minerals are comparatively few. They include quartz, feldspars, nephelite, sodalite, leucite, mica, pyroxenes, amphiboles, chrysolite, kaolin, talc and serpentine. These minerals may appear in igneous rocks as coarse crystals in granites, syenites and diorites or as very fine grained dispersions in basalt and felsite. When the latter rocks occur in an ore, their specific gravities depend on the minerals present and structure. The same is true for the sedimentary and metamorphic rocks (sandstones, shales, gneiss, slate, schists). A comparison of specific gravities for the minerals listed in Fig. 1 with that of TBE (see Table I) shows that the important rock-forming minerals, with the exception of pyroxenes, amphiboles and chrysolite (olivine), lie in the specific gravity range of less than 2.96 and can therefore be separated by TBE. The ore structure is important both in determining the apparent specific gravity and the efficiency of TBE recovery. The structure can be compact (as in

Jan 1, 1963

By R. J. Stevens

THE Roan Antelope Smelter commenced operations in October, 1931. As originally designed, its equipment consisted of one reverberatory furnace, 120 X 25 ft, two Peirce-Smith converters 12 X 20 ft, and one straight line casting machine. Since that time the following additions have been made: One reverberatory furnace 120 ft X 28 ft (1934) One reverberatory furnace 95 ft X 28 ft (1943) Two 12 X 20 ft Peirce-Smith converters (1934 and 1938) One 13 X 30 ft holding furnace 6 (1938) One straight line casting machine and 2 ladle tilting quadrants (1934) The metallurgy of the smelting process is comparatively simple. However, there are several features of operation which are uncommon to most copper smelters: (1) The high grade of concentrate treated; this has always been about 50 pct copper. (2) The high flux burden on the charge. This is necessary because of the deficiency of bases'in the concentrate and the high alumina content of the concentrate. (3) The frequent necessity of adding coal to the furnace charge to control the matte grade. (4) The high grade of matte produced. This has led' to unusual converter problems. From the commencement of operations, the ore mined has come from the Roan Basin orebody. The concentrate produced from this ore consists mainly of chalcocite and shale with small proportions of other copper minerals. As mining operations extend to the Roan Extension orebody, the proportions of bornite and chalcopyrite in the concentrate will increase with a corresponding decrease in the copper content of the concentrate. Because of the concentrate grade the capacity of the reverberatory . furnaces in terms of tons of copper produced per ton of coal burned is high.. This ratio is usually over 2.2, and on especially favourable runs has reached 2.6. Reference to Table , shows that the iron content of the concentrate is unusually low. Only part of this iron is available for slag formation, the balance going to the matte. To make up this deficiency in bases, limerock is added to the furnace charge. This flux ensures a slag that is of the correct silicate degree, is sufficiently fluid, of low specific gravity, and it counteracts the thickening effect of the alumina present. An ample supply of flux is obtainable from Ndola, 2 2 miles distant by rail. Although the reverberatory slag has a high copper content, the slag fall is low and the copper loss in the slag now rarely exceeds 1.0 pct of the total copper charged. The blister copper shipped is of such purity that only one fire refining operation has been necessary to produce a wirebar with properties comparable to electrolytic copper. Bismuth has always been the most troublesome impurity and consequently the problem of its control in the finished product has been of prime importance. Practically none is removed in the reverberatory furnace. The bulk of the elimina-

Jan 1, 1947

By C. W. Spencer, F. G. Hochgraf, R. F. Cheney

Columnar grained specimens of nickel, containing 0.25 pct Si and 0.22 pct Mn, have been exposed to liquid bismuth in the temperature range 670° to 1050°C. Under isothermal conditions the liquid penetration rate is constant. The activation energy for the process is 22,000 cal per g-atom. Small amounts of plastic deformation, introduced into specimens prior to exposure, increase the penetration rate. The slou. step in liquid film penetration is associated with a reaction which occurs at or near the leading edge of the film. Either transfer of nickel across the liquid-solid inteqace or diffusion in the grain boundary ahead of the liquid film is suggested. Aliquid metal, if brought into contact with the surface of an unstrained solid metal, will usually penetrate to some extent into the grain boundaries of the solid. Under isothermal conditions the extent of penetration after any particular time of exposure is related to the relative magnitudes of the interfacial tensions concerned.1,2 If the liquid-solid interfacial tension is less than one-half the grain boundary tension the liquid may penetrate at a relatively rapid rate for an indefinite distance into the grain boundary surfaces. If the liquid-solid interfacial tension is greater than one-half the grain boundary energy, liquid penetration occurs at a continually decreasing rate so that after the liquid has penetrated to a relatively short distance below the surface the process essentially ceases.3 Many observations of a qualitative nature concerning inter crystalline attack by liquid metals have been reported, for example, liquid bismuth upon copper,' liquid mercury upon brass,4 and liquid mercury upon nickel.' Scheil and Schessl determined the rate of penetration of liquid bismuth into the grain boundaries of hot rolled copper rod? At constant temperature, penetration rate was found to be independent of the depth penetrated, the rate in- creasing with increasing temperature corresponding to an activation energy of 20,000 cal per g-atom for the process. It was suggested that at lower temperatures the liquid travelled mainly along lines of three grain intersections while at temperatures greater than 1000°C essentially all grain boundary surfaces were covered. Recently, in a study of copper bicrystals having a common [loo] axis it was found that at 649°C bismuth penetrated 22, 25, and 63 deg boundaries while it did not penetrate 2, 12, 15, and 72 deg boundaries.' Elbaum reported that liquid gallium penetrates aluminum grain boundaries to a depth of 0.6 cm after 11 hr at 27°c.8 Assuming that the rate controlling step in the process was diffusion down the liquid film to the specimen surface, a diffusion coefficient of 10-5 cm2 per sec was calculated. This paper reports a study of the penetration of bismuth-nickel liquids into the grain boundaries of a nickel alloy, containing 0.25 pct Si and 0.22 pct Mn as principal alloying elements. The phase diagram

Jan 1, 1962

By E. I. Radzinovsky, D. W. Dareing

This paper presents theory which is used to predict rock-bit bearing life reduction due to simple harmonic variations in bit forces. The theory is based on the premise that if a constant load acts for a certain fraction of the life which the bearing would have if that constant load were applied for its entire life, then the same fraction of thelife of the bearing is consumed. Total bearing life is related to simple harmonic variations in bearing life associated with instantaneous bearing loads. The results show that rock bit bearing life is not affected appreciably by forces commonly impressed upon a bit, but it is affecied appreciably by relatively large dynamic bit forces occasionally encountered during drilling. In addition, the results show that the life of sealed bearings is more sensitive to bit force variations than is the life of unsealed bearings. INTRODUCTION Roller bearings are important components in roller cone rock bits because they transmit a large portion of the drill collar weight to the formation being drilled. Unfortunately, they have a relatively short life under down-hole drilling conditions. Roller bearings are usually the first bit components to fail, and their failure leads immediately to failure of the entire bit. Short roller bearing life, and thus short bit life, is due mainly to high unit loads transmitted by the bit and to the adverse environment in which the bearings operate. The results of the study discussed in this report show how dynamic bit forces also affect roller bearing life. The purpose of this paper is to discuss theory developed to predict the effect of different magnitudes of periodic bit forces on roller bearing life. Theoretical results are used to compare the life of rock bit roller bearings subjected to steady forces to the life of rock bit roller bearings subjected to unsteady forces similar to the type of unsteady forces measured at the bit with a special downhole recording instrument. BACKGROUND AIanufacturers of bearings have conducted laboratory tests which show how bearing life is affected by steady bearing load. 1 The well-known empirical equation which defines bearing life follows from bearing test data. It is: where L = bearing life, hr P = bearing load, Ib C = constant q = exponent (constant). The effect of environment on bearing performance is manifested through the exponent q and the constant, C. King,2 in similar tests conducted on roller bearings used in rock bits, showed that, in addition to the load, the environment (abrasive materials, chemical components, etc.) greatly affects bearing life. His data, which show how the life of roller bearings in a 7-7/8-in. W7R bit rotating at 60 rpm is affected by bit weight and fluid environment, are displayed on a log-log plot by broken lines made up of straight line segments. Each broken line corresponds to a given environment. One segment (q = 1.4) of the broken line corresponding to a fluid environment of barite mud is shown in Fig. 1 along

Jan 1, 1966

By A. W. H. Morris, E. A. Steigerwald

The jatzgue beizazriov oj Mietal matrix co))zpos~tes in tension -lensiom loading has been imestigated as a junction of Dolume fraclion veinfovcelnent using the model systems of a silver matrix reinforced with contlnuous or dzscontztinuous aligned tungsten jilamenls and continuous aligned steel filamenls. Appreciable impvocetnents in fatigue strength were obseved in all syslems inzvesLigated, the degree of sl renglhenng-increasing with increasing volume fraclion of reinforcement. The mode of fatigue failure was found to be a function of colutrre jp-actiotz and was also noted to be controlled by the relative fatigue and strength characlerislics of the matrix and reinforcemenl. THE advantages to be gained by suitably incorporating high-strength filaments or whiskers into metallic matrices are well-recognized.' To date emphasis has been placed on the experimental determination of tensile strengths and elastic moduli of metal matrix composites measured parallel to unidirectionally aligned filaments. Several attempts have been made to relate experimentally measured tensile properties to theoretical values calculated from the properties of the components on the basis of the relatively simple "rule of mixtures" analysis. However, relatively few data have been reported in the literature on the fatigue behavior and mechanism of fatigue failure of metal matrix composites. In a study of fatigue crack propagation in aluminum plus steel wires and aluminum plus tungsten wires, Forsyth et a1.2 found that the incorporation of small numbers of filaments suitably dispersed were capable of substantially reducing the rate of fatigue crack propagation. For this purpose, the strength of the filaments appeared to be more important than the aspect ratio and the authors reported that parallel filaments were not the most favorable orientation for increased strength. In a basic study of the fiber reinforcement of metals, Williams and 0'brien3 report preliminary results which indicate a considerable improvement in fatigue strength in reversed bending fatigue of a steel wire-reinforced aluminum alloy composite. In a study of the influence of interfacial bonding on fatigue behavior, Baker4 has also reported improved fatigue properties in stainless steel-reinforced aluminum composites. In contrast, Ham and place5 report that, although tensile properties are improved greatly by filament reinforcement, the reinforcement of copper with continuous, brittle tungsten wires up to 23 vol pct was comparatively ineffective against fatigue. The authors attribute the poor fatigue properties of the composite to fatigue hardening of the matrix at the tips of cracks which can build up stress concentrations sufficiently large to fracture proximate filaments. Baker and cratchley6 failed to find marked improvements in the reversed-bending fatigue properties of silica-reinforced aluminum. The study was complicated by the complex behavior in a composite during the compres-sive half-cycles imposed in this type of loading. This was manifested in the failure of the composites by de-lamination, a contributing factor being the presence of aluminum oxide at the matrix-filament interface. Prior to the general acceptance of filament-rein-

Jan 1, 1968

By W. A. Dickinson, H. F. Hendershot

THIS paper is a brief discussion of the past and present methods employed by the Huntington Works of The International Nickel Co., Inc., in the production of nickel and high nickel alloy seamless tubing. The various operations for both hot and cold processing will be considered in their natural sequence, together with the processing characteristics of the high nickel alloys and some descriptions of the equipment used. The tools and lubricants currently in use will be described. This discussion will relate primarily to nickel, Monel,† and Inconel,† since these are the most common of the many alloys processed into tubing at the Huntington Works. The nominal compositions of the materials are shown in Table I. CONVERSION FROM SOLID BILLETS TO TUBE SHELLS History The commercial production of seamless nickel and high nickel alloy tube shells is a comparatively recent development, the first nickel shells having been produced in 1922, Monel in 1930, and Inconel in 1931 on rotary-type piercing mills. Rolled or forged billets, ranging from 3 ½ - to 7 ½ in. diam, were pierced to produce shells ranging' in size from 4 3/8 in. OD X 0.180 in. wall to 8 3/8 in. OD X 1.0 in. wall. After piercing, the shells. were further processed by hot rolling, reeling, and sizing. Subsequent to these operations the shells were either supplied to the trade as "hot finished" tubes, or were processed by cold drawing to smaller sizes at the Huntington Works of the International Nickel Co. The extrusion of nickel and high nickel alloys also may be classed as a relative newcomer to the field of hot-forming methods, for it was not until 1928 that the commercial extrusion of these alloys was begun on a 600 long ton vertical extrusion press installed at Zenith Works of Henry Wiggin and Co., Ltd., Glasgow, Scotland. This press did considerable pioneer work and the results were so favorable that in 1937 a -2200 long ton horizontal press was installed. The quality of the inside surface of the tubing produced on this press was superior to that produced by piercing on a rotary-type mill and, as a result of this experience, a 4000 ton horizontal extrusion press was installed at the Huntington Works in 1943. Billet Preparation The first step in the extrusion, process is the selection of ingots with good hot malleability, as indicated by the test described by Martin and Bieber.1 Ingots then are forged into rough rounds which are machined to the desired billet diameter on a "bar peeler." This machine consists of a rotary head which carries the cutting tools and is driven by a 200 hp, dc motor. The feed mechanism consists of hydraulically driven input and output carriages on the respective sides of the cutter head. The diameter of the forgings used and the machined size or "billet diameter" that corresponds to the four different sizes of

Jan 1, 1951

By B. M. Larsen

Attempting to review the fundamental aspects of segregation in steel ingots of all types in a paper of reasonable length, we encounter two difficulties: (I) the fact that a large number of different physical and chemical effects are involved, and (2) rather incomplete and confusing evidence on certain aspects of detail and mechanism in the freezing process in which the segregation effect is involved. The best solution seemed to be to link together most of the underlying factors into a simplified theoretical picture that appears to the writer to explain most of the observed data, in the hope that this will serve as a reasonably good target for discussion and criticism. Segregation effects, especially in steel ingots or castings, are often divided into " microscopic" and "macroscopic," depending on whether the variations in concentration of solutes or dissolved elements in the iron occur as: (I) a periodic variation over the small distances between the nuclei and the surfaces of the primary grains, or (2) as a larger scale effect involving concentration gradients over distances of the order of several inches, more or less. The reason for this somewhat artificial division is, of course, that it is only the macroscopic scale effect that has much practical importance. About the only effect of practical importance that results from microscopic segregation is the banded structure often left in rolled sections, and even this is relatively harmless in most cases. However, the causes of microscopic segregation also untlerly the larger scale effect, so we must first consider matters such as the formation and growth of crystal nuclei, selective freezing and diffusion, and others that are fundamental to all sepregation effects. Undercooling and Nuclei Formation It is probable that although the degree of undercooling is small in iron, as in metals in general, a certain amount of it takes place, and also that the number of crystal nuclei increases very rapidly with increased undercooling below the liquidus temperature. In practical terms this means that the nuclei number illcreases very rapidly with increased cooling or freezing rate, thus being dependent on the rate of heat flow out from the zone of crystallization. Temperature Gradients and Heat Dissipation during Freezing Each pound of steel evolves about 100 B.t.u. when freezing. In addition to this, the temperature gradient in the solidified portion (required to dissipate the heat as freezing progresses into the axis) necessitates a loss of heat required to cool the solid metal below its freezing range, which is equivalent to an amount of not so much less in magnitude. In a 5-ton ingot, the total would include about one million B.t.u. for freezing alone and about 0.4 to 0.5 million B.t.u. for the gradient, up to the end of the freezing period. Thus the rate of freezing depends primarily on the rate of heat dissipation. In the ordinary ingot shapes, the axial rate of growth of the solid

Jan 1, 1945

By N. A. Tiner

A study was made of the effects of temperature, type of loading, and electric polarization on the fracturing behavior of copper and zinc coated with mercury. Copper showed an em-brittlement only in cyclic loading, whereas zinc showed an em-brittlenzent in both static and cyclic loading. The embrittle-ment of zinc in static loading was prevented by sub-zero cooling to a temperatzcre of about -70°F. The emhrittlement of both metals was sliglztly reduced by cathodic polarization of mercury. The basic processes involved in fracturing were discussed in the light of these observations. When a solid metal is in contact with certain liquid metals possessing high wetting characteristics, a weakening effect is produced, and the solid metal fractures in brittle manner at a relatively low stress. This lowering of the fracture stress generally is considered different from the stress cracking caused by a corrosive liquid environment and is attributed to the lowering of the solid-liquid interface tension at the grain boundaries.1-4 The purpose of this paper is to describe a number of observations on the special features of fracturing of copper and zinc coated with a liquid mercury film, and to analyze the basic processes involved in fracturing in the light of these observations. EXPERIMENTAL OBSERVATIONS I) Effect of Type of Loading—The evidence appears to indicate that in static loading, metals usually fracture by the initiation of microcracks in the interior preferentially at the grain boundaries or at the intersection of slip bands.' In cyclic loading, cracks develop on the surface within the active slip zones, and gradually propagate with increasing num- ber of cycles.6'7 Because of this difference in the manner of initiation of cracks, a series of bare and mercury coated copper and zinc specimens was subjected to static and cyclic loading, and their fracturing behavior was examined. The specimens were machined to 0.25 in. in diam and 1 in. in length from a high-purity commercial bar stock, and annealed at an appropriate temperature. Mercury was applied to the surface of the specimens by rubbing with cotton wool soaked in a saturated solution of HgCl2 or by etching with a dilute solution of HC1 and rubbing with purified mercury and by washing in water. The static tension load-extension curves were obtained by means of a Riele Screw Power Universal Testing Machine. The room-temperature load-extension curves for copper and zinc are shown in Fig. 1. The deformation behavior of copper, as judged from the general configuration of the load-extension curve, was not affected by mercury coating. The maximum load to fracture and the elongation at the maximum load were practically the same for both specimens. The mercury coated copper, however, showed somewhat less localized necking and had smaller reduction of area than the uncoated metal. The behavior of mercury coated zinc was radically different from the behavior of uncoated metal. The load-extension curves were the same at the

Jan 1, 1962

By J. J. Gilman

THEORIES of fracture in metals have been based primarily on the dependence of fracture strength on grain size. This dependence was first observed by Masing and Polanyi.l These workers, as well as 0rowan12 and Davidenkov and Wittman,' thought the grain size could be equated with the crack size in the Griffith condition for crack propagation.4 In this way they could account for the observed proportionality between fracture stress and the reciprocal square root of the grain size. The chief results of recent investigations of the fracture strength of polycrystals are summarized in Fig. 1. Low for iron,5 Petch for iron,' Greenwood and Quarrel for zinc, Petch and Zein for zinc,' and Hauser, Landon, and Dorn for magnesium'' have all found that the fracture stress of a polycrystal is proportional to the reciprocal square root of the grain size. Also, they find that, for large grain sizes, the fracture stress lies near the extrapolation of the yield-stress curve determined at small grain sizes; where measurable plastic strain precedes fracture. Low9 has gone a step further and shown that, in Range 1, the fracture stress in tension is almost identical to the yield stress in compression for a given grain size. Homes and Gouzou, 10 and Low also have shown that, in Range 2 of Fig. 1, microcracks form when the yield stress is reached, but they do not cause failure until the stress reaches a much higher value. The fact that yielding always precedes fracture suggests that fracture is induced by plastic flow. A mechanism by which this might occur was first proposed by Zener.11 He pointed out that blocked dislocations would cause stress concentrations which might cause fracture. The blocking would be caused by grain boundaries. This idea has been developed by Eshelby, Frank, and Nabarro,12 by Koehler,13 and by Stroh.14 By means of etchpits blocked dislocations have been observed in brass by Jacquet,15 in zinc by Gilman,16 and in lithium fluoride by Gilman and johnston. The blocked-dislocation theory and the experiments that bear on it have been summarized by Mott.18 One of the strong points of the blocked-dislocation theory is that it can explain the grain-size dependence of the fracture stress in a natural way. However, Low9 has pointed out that the theory is not satisfying when it is considered quantitatively. Gilman10 also has criticized the theory and presented an alternative interpretation of the relation between fracture stress and grain size. Since the blocked-dislocation theory is not the only theory that can explain in the grain-size effect, it is necessary to find other evidence either to support or deny it. In this investigation the following points were studied: 1) If blocked dislocations normally cause fracture, then the fracture stress ought to be very high in the absence of plastic glide. Is it? 2) If dislocations must be blocked in order for metals to fracture, then certain types of grain

Jan 1, 1959

By Nicholas J. Grant, William H. Ferguson, Bill C. Giessen

Ta-lr alloys have been examined over the complete range of compositions using metallographic and X-ray techniques. The terminal solid-solubility limits, solidus temperatures, and intermediate phases were determined. There are four inter-mediate phases: o, tetragonal, analogous to a (Fe-Cr); 0,. orthorhombic; az, tetragonal; and a TaZr,, cubic, AuCu, structure. Of these, o and a, melt peritecticaLly, a, decomposes peritectoidally, and a TaIrs has a congruent melting point. Three peri-tectic and one eutectic reactions occur. 1 HE Ta-Ir phase diagram has not been treated in the literature. Intermetallic phases and terminal solid solubilities have been described and estimated.'-4 The previous findings have been confirmed in this work. A complete diagram with additional phases and solidus curves is presented. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by the National Research Corp., Cambridge, Mass., and iridium powder of 99.9 pct purity, supplied by the Bishop Co., Malvern, Pa. Both powders were -200 mesh. Table I lists the analyses as given by the suppliers. A standard procedure was employed in making the alloy buttons, which was described in detail in Refs. 5 and 6, and which included repeated arc-melting of powder compacts and determination of the composition by the weight-balance method. This is especially justifiable due to the similar vapor pressures of tantalum and iridium. In the critical parts of the diagram, a spacing of 1/2 at. pct was used, based on premelted master alloy material. The observed structures and X-ray spectra were consistent with the composition sequence of the alloys. Table II lists the final alloy atomic percentages with the calculated percent error of composition. Cross sections representative in grain size and composition were selected for the study, as described in Ref. 5. Based on prior experience, no contamination from the tungsten electrode was considered. Temperature measurements were obtained using a Leeds and Northrup optical pyrometer and have been described extensively in Refs. 5 and 6. All heat treatments were made in the high-vacuum tantalum tube furnace mentioned in Ref. 5. Samples annealed in tantalum containers cooled from 1800" to 1000"~ in 5 sec; those annealed in ceramic crucibles cooled over the same range in 15 to 30 sec. The thermal treatments are listed in Table 111. All specimens were homogenized at 1735°C for 24 hr. Tantalum-rich compositions were treated in tantalum buckets. Iridium-rich compositions were annealed in tantalum buckets below the eutectic temperature of 1950°C; up to 2200°C, tungsten-lined tantalum baskets were used; and above 2200°C thoria crucibles were used. It was found that refractory oxides (in early stages of the investigation alumina crucibles were used up to 1800°C and thoria crucibles were used to 2400"~) give off minute amounts of oxygen and thereby influence the microstructure considerably, or react directly with the alloys.

Jan 1, 1963

By B. M. Larsen

ATTEMPTING to review the fundamental aspects of segregation in steel ingots of all types in a paper of reasonable length, we encounter two difficulties: (I) the fact that a large number of different physical and chemical effects are involved, and (2) rather incomplete and confusing evidence on certain aspects of detail and mechanism in the freezing process in which the segregation effect is involved. The best solution seemed to be to link together most of the underlying factors into a simplified theoretical picture that appears to the writer to explain most of the observed data, in the hope that this will serve as a reasonably good target for discussion and criticism. Segregation effects, especially in steel ingots or castings, are often divided into " microscopic " and " macroscopic," depending on whether the variations in concentration of solutes? or dissolved elements in the iron occur as: (I) a periodic variation over the small distances between the nuclei and the surfaces of the primary grains, or (2) as a larger scale effect involving concentration gradients over distances of the order of several inches, more or less. The reason for this somewhat artificial division is, of course, that it is only the macroscopic scale effect that has much practical importance. About the only effect of practical importance that results from microscopic segregation is the banded structure often left in rolled sections, and even this is relatively harmless in most cases. However, the causes of microscopic segregation also underly the larger scale effect, so we must first consider matters such as the formation and growth of crystal nuclei, selective freezing and diffusion, and others that are fundamental to all segregation effects. UNDERCOOLING AND NUCLEI FORMATION It is probable that although the degree of undercooling is small in iron, as in metals in general, a certain amount of it takes place, and also that the number of crystal nuclei increases very rapidly with increased undercooling below the liquidus tempera¬ture. In practical terms this means that the nuclei number increases very rapidly with increased cooling or freezing rate, thus being dependent on the rate of heat flow out from the zone of crystallization. TEMPERATURE GRADIENTS AND HEAT DISSIPATION DURING FREEZING Each pound of steel evolves about 100 B.t.u. when freezing. In addition to this, the temperature gradient in the solidified portion (required to dissipate the heat as freezing progresses into the axis) necessitates a loss of heat required to cool the solid metal below its freezing range, which is equivalent to an amount of not so much less in magnitude. In a 5-ton ingot, the total would include about one million B.t.u. for freezing alone and about 0.4 to 0.5 million B.t.u. for the gradient, up to the end of the freezing period: Thus the rate of freezing depends primarily on the rate of heat dissipation. In the ordinary ingot shapes, the axial rate of growth of the solid

Jan 1, 1944