Search Documents

By A Fern, A Hawkes, o, W Smith, K Mee

Serious Injury and Fatality (SIF) prevention remains a priority focus within high-risk industries sector. A major mining operation sought to strengthen their approach to the management of high-risk activities through an in-depth review of all historical incidents that had serious injury or fatality potential (SIFp) events (sometimes known as hi-potential events). The analysis found that the organisation invested a disproportionate level of resources, time and effort on low consequence incidents with a high proportion of SIFp incidents going under the radar. It was found that 76 per cent of SIFp incidents were rated in moderate or lower risk categories and conversely, almost half of those incidents with a ‘serious risk’ rating had little or no potential for a serious outcome. As a result of this project, the operation engaged in a renewed focus on critical risk management and enhanced its operating cadence in critical risk for the workforce. This included bow tie analysis, an update to critical risk standards and increased workforce engagement in the use of critical control verifications in the field. Data analytics with lead and lag indicators continue to provide senior leadership team and risk owners with an understanding of exposure for SIFp and control effectiveness. The audience will take away learnings from a real-world case study that provides data-driven insights of the human, local and organisational factors contributing to incidents with SIF potential. In addition, participants will understand the steps taken to categorise and analyse this incident data and the initiatives currently being implemented by the organisation as a result.

Apr 16, 2024

By D J. Williams

The majority of surface tailings storage facilities continue to employ sub-aerial tailings slurry deposition. Surface TSFs are typically sized and operated in a way to minimise the initial capital cost of the facility, driven largely by the net present value approach to accounting. This generally leads to too small a storage, too fast a rate of rise of the tailings, and difficulties in managing supernatant water. In turn, this results in wet and soft tailings deposits of high moisture content and low density, and the need for frequent and costly tailings dam raises. Further, such tailings deposits often do not facilitate closure and rehabilitation of the facility. Globally, there are on average over two failures annually of such tailings dams, resulting in loss of life, damage to infrastructure and environmental impact downstream, and the loss of company shareholder value and reputation. Recent high profile tailings dam failures are threatening the mining industry’s financial and social licence to operate.Among the physical processes that tailings undergo on sub-aerial deposition are beaching, hydraulic sorting down the beach according to particle size and specific gravity, settling, consolidation, and desiccation on exposure to the sun and wind. Beaching and hydraulic sorting have proved difficult to test at laboratory scale and difficult to model, and are best assessed in the field. Settling, consolidation and desiccation may be assessed at laboratory scale, but to date there has been an absence of tests to form the basis for the design and management of tailings deposition, and ultimate closure and rehabilitation. The paper describes recent advances in tailings testing methods, including a purpose-built slurry consolidometer that tests the settling and consolidation of tailings from a slurry consistency, simulating increasing tailings depth to about 50 m; and a purpose-built instrumented column that tests the settling, self-weight consolidation and desiccation of a surface layer of tailings, also from a slurry consistency. Selected test results from these two apparatus are presented in the paper, together with brief descriptions of how they may be used to better design tailings slurry deposition. In addition, planned further advances in tailings testing methods are briefly described.CITATION:Williams, D J, 2018. Recent advances in tailings testing methods, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 8–37 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

A poured slag bottom is universally considered to be the best type bottom for copper reverberatory furnaces. It is impervious to molten matte and ready for immediate use.When molten slag is not available a monolithic silica bottom is the second best; such a bottom has been adopted at Mount Morgan. The laying of such a bottom is a phase of smelter construction on which so little real information is obtainable that a day to day record of such a recent example as Mt. Morgan's 19 ft. x 40 ft. reverberatory may be of interest. The work was done under the direction of E. Pesout, of McGill Smelter, Nevada. PREPARATION OF THE BOTTOMA 26-inch bed of closely packed firebrick with sand-filled joints was first laid on the clean, dry concrete foundation and the whole dried out by small fires maintained on the brickwork for several days. Ninety tons of silica sand was meantime thoroughly dried and stored in clean drums. This sand must be low in FeO and CaO and contain about 95% Si02 , the majority of which should be present as tridymite. This form of silica shows little expansion at high temperatures, for it is the form stable between 870° and 1470° C.Its presence thus minimises disturbance to the bottom by the expansion which, during the burning in, would mark the transformation of quartz to tridymite.

Jan 1, 1939

Metana Minerals commenced life in 1970 and graduated to a mining company in 1981 with the opening of a small alluvial tin-tantalite mine at Wodgina (W.A.) The present board of directors assumed control of the company in 1978 and established the exploration and development philosophies that have guided the company's expansion to its present status as an emerging diversified miner. An ability and willingness to raise equity capital when required has been a feature of the company. Company activities include exploration for gold, diamonds, heavy mineral sands, polymetallic (base and precious metals) deposits, strategic minerals, rare earths, oil and gas in a geographical distribution covering the entire Australian mainland Metana owns and/or operates four gold mines (Reedy, Mt Magnet, Youanmi and Howley) and at the time of writing is developing a fifth gold mine - its first underground mine - at Rothsay. In contrast to many similar or larger sized companies, Metana undertakes most activities itself rather than through the use of consultants or contractors. In-house services include: analytical and metallurgical laboratories, plant engineering design and construction, drilling and mining (earthmoving) Metana Minerals has established an enviable reputation for technical excellence and this expertise has placed the company in a sound position to continue its growth pattern into the future. This growth will be achieved through a combination of low cost and successful exploration and acquisition of suitable mines either directly or through corporate activity.

Jan 1, 1989

By K Peters, C McKenzie

New Zealand has an established history of gold production beginning with the gold rushes of the 19th century in the Coromandel, Nelson/Marlborough, West Coast and Otago regions. Despite this, the number of significant modern hard rock gold operations has been limited in recent years due to a lack of sustained exploration capital and not limited geological prospectivity.The New Zealand Government is actively encouraging explorers to invest in New Zealand through a series of targeted promotional visits, more importantly through the acquisition of precompetitive regional geophysical data. Data collection has been completed over the prospective Northland epithermal district and a large portion of the South IslandÆs west coast that is prospective for both orogenic gold and intrusive related gold.Analysis of new data has been an important component in aiding the generation of exploration targets from prospectivity modelling. Determining the prospectivity of an area involves reviewing all the available data and analysing it with respect to the most up-to-date mineral system model for the mineralisation style of interest. Using the weights of evidence modelling approach, the most prospective areas for epithermal gold-silver, orogenic gold and intrusion-related gold have been identified. The key exploration parameters relevant to each mineral system are first represented spatially and then statistically combined into a single prospectivity map. New potentially economic deposits could be found by focusing exploration on targets identified from these models. The prospectivity modelling approach can greatly reduce the risk involved in mineral exploration.CITATION:Peters, K and McKenzie, C, 2013. New Zealand gold potential - using mineral prospectivity modelling to evaluate gold-bearing mineral systems in an underexplored country, in Proceedings World Gold 2013 , pp 479-486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Effect of Spacer Chain Length on the Flotation of Kaolinite and Quartz by Using Gemini Surfactants as Collector

Sep 13, 2010

By N B. McCaffrey, V Glenn, C Johns, P D. Erskine, A T. Fletcher

"Underground coal mining is the dominant method of extracting thermal and coking coal in the southern and western coalfields of New South Wales. Monitoring mining-related subsidence forms an important component of environmental impact assessments and subsidence management plans, particularly when there are conflicts between the interests and requirements of mining and environment and community groups. However, there are few specific guidelines for monitoring the impacts of subsidence on terrestrial and aquatic ecosystems, leading to inconsistent policy approaches and highly variable abilities of monitoring programs to accurately detect biological change.This paper highlights the use of a conceptual framework to guide the development of a long-term ecological monitoring program at an underground coalmine in the Western Blue Mountains, New South Wales. Two pilot studies are described: determining the level of observer agreement to assess the condition of a vulnerable tree species (Capertee Stringybark) comparing field sampling methods for detecting a rare heath shrub, Epacris muelleri, using a power analysis to determine sampling intensity requirements.These examples demonstrate that investment in initial pilot studies to test different monitoring approaches can have long-term benefits for stakeholders by more confidently being able to detect potential impacts.CITATION:McCaffrey, N?B,?Glenn, V, Erskine, P?D, Johns,?C?and Fletcher, A?T, 2014. Detecting long-term ecological impacts of subsidence from underground coal mining – a tale of two pilot tests, in Proceedings Life-of-Mine 2014, pp 139–152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 16, 2014

One of the most important goals of the experiments is to determine deformation and strength of the rock specimen under applying triaxial load, the status of failure condition is one of the subjects which can be used in soil mechanic and foundation engineering applications. To investigate the effect of confining pressure on the triaxial test, the rock has been considered as bonded-particles method and has been simulated by particle flow code three dimensions (PFC3D). This model, does not have pre-existing microcracks and all the particles have the same size (2 mm diameter), equal to the real specimen shape. To compare the mechanical behavior and failure pattern of the numerical and experimental results at uniaxial and triaxial tests at the same conditions, the Young's modulus, Possion's ratio as well as maximum axial stress have been considered. On the other hand, the microcracks growth and change of failure pattern at the modelling of the uniaxial and triaxial tests with different confining pressures up to failure point were reported. According to the experimental work, the number density of microcracks decreases from starting value and remains almost constant up to the failure beyond that point. The comparison of the numerical and experimental results of maximum axial stress and the Possion's ratio revealed good accordance. The initial number density of microcracks at the model was zero and increased while microcracking. Also, the sudden increment around the maximum stress was observed which is because of unstable growing of microcracks near the maximum stress. In all uniaxial and triaxial tests with different confining stresses, the number density of microcracks during the failure remains almost constant which can be considered as a proof of failure occurring in the model. The experimental results indicate the similar trend as well.

Nov 25, 2010

By S F. Simmons

At Broadlands-Ohaaki geothermal system, TVZ, mineral distribution patterns in geothermal wells are analogous to those in epithermal veins. Fluid flow through geothermal wells is focused over vertical intervals >500 m with discharge at rates up to 90 l/s. Focused flow at similar rates also occurs in natural systems where hydrothermal eruption vents provide enhanced vertical permeability. These vents are commonly aligned with the tectonic fabric, indicating fault control at depth. We suggest that host rock strength and structural context exert significant control on the hydrological regime conducive to epithermal mineralisation.

Jan 1, 2005

By R G. Barker, A B. Christie

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. More than 11 Moz of Au and 50 Moz of Ag have been produced from epithermal deposits in New Zealand, almost entirely from 50 deposits in the Hauraki goldfield. Since the 1980s, new deposits have been discovered at Waihi (Favona, Trio, Correnso) and nearby at Golden Cross. Feasibility studies into reopening the Talisman mine at Karangahake are continuing, and advanced projects with preliminary inferred resource estimates are reported at Wharekirauponga, Neavesville and Muirs. In the Taupo Volcanic Zone, 11 prospects have been drilled, resulting in the definition of large but low-grade Au-Ag resources at Ohakuri. In Northland, several Au, Ag and/or Hg prospects are known, and small quantities of Ag and Hg have been mined. Six prospects have had some drilling, with the most advanced exploration at Puhipuhi. The application of Taupo Volcanic Zone geothermal systems research to the modelling of former hydrothermal mineralising processes in some epithermal prospects has enabled better targeting of exploration.CITATION:Christie, A B and Barker, R G, 2015. Exploration for epithermal gold deposits in New Zealand, in Proceedings PACRIM 2015 Congress, pp 533–540 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Recovery of Fine Gold Particles from Philippine Gold Deposits by Enhanced Gravity Concentration and Flotation The objective of the study is to determine the applicability of enhanced gravity concentration (EGC) and flotation for gold recovery. While gravity concentration methods have long been applied to gold ores, especially to free-milling types that requires minimal beneficiation, flotation for gold recovery has not yet taken hold as a major operation in the Philippine setting. In this study, the application of EGC and flotation for gold is applied and compared to the existing methods for gold recovery. Two samples, with assays of 7.315 and 5.333 g Au/MT (samples 1 and 2, respectively) are used for this study. These samples are subjected to mineralogical studies and is found to have a gold-particle size ranging 10 to 200 microns. To verify the separation size, the mesh-of-grind (MOG) is used as the primary parameter for experimentation. Initially, the samples are stage-crushed, ground, and subjected to EGC using a Falcon SB40 Concentrator. Based on the results, the two samples showed that recovery increases with a finer MOG. The ratio of concentration (K) decreases with a finer MOG. This shows that there should be sufficient liberation of the gold values for EGC to be effective. The effect of the enhancement is to pronounce the difference in specific gravity of the minerals, promoting better separation. This is validated by the high recovery values of 86.97 per cent and 98.73 per cent exhibited respectively for samples 1 and 2 (at 54 microns). For the flotation runs, sample 2 with an average particle size of 80 per cent passing 74 microns is examined using thiocarbamate-based collectors for roughing and subsequently exhibited a recovery of 96.32 per cent. At this point, the concentration ratio (K) is noted as an important efficiency indicator for flotation process since it yielded a very low-mass and high-metal content concentrate.

Sep 13, 2010

By K R. Vining, T E. Norgate

A study was carried out to compare the environmental impacts of the two major iron ore agglomeration processes, sintering and pelletising, using life cycle assessment (LCA) methodology. The following agglomeration processing routes, with the fuel options shown, were investigated:sintering with combined natural gas/coke breeze or charcoal as fuel, grate-kiln pelletising with combined natural gas/coke breeze as fuel, and straight-grate pelletising with combined natural gas/coke breeze as fuel. Inventory data for each process derived from the literature, and in some instances supplemented by additional simulations and calculations, were used in the study and the environmental impact categories considered were gross energy requirement (GER), global warming potential (GWP) and acidification potential (AP). The results of the study showed that the GER, GWP and AP for a sinter plant are higher than those for a pellet plant for the same amount of metallic iron in the agglomerated products. These results are partly due to higher consumption of solid fuel and flux in the sintering process. However, it should be pointed out that the study only compared substantially fluxed sinters with acid pellets that may require additional flux (and hence potentially more greenhouse gases emissions) to be a balanced blast furnace feedstock. Extending the LCA to the blast furnace process stage was beyond the scope of the current study. Within the sinter plant, the sintering stage itself is the largest contributor to the GER, GWP and AP. In the case of pellet plant, the pellet induration stage is the largest contributor to the various environmental impacts. The GER and GWP of a straight-grate pellet plant are marginally higher than those of a grate-kiln pellet plant due to the higher electrical power required by the straight grate system. The substitution of coke breeze with charcoal in the sintering process results in an increase in GER but a decrease in GWP. However, a substantial proportion of the GER is derived from renewable sources (wood), resulting in a decrease in the non-renewable components of this environmental impact. Given the source of the inventory data and the assumptions and approximations made in carrying out the LCAs, it is emphasised that the results presented in this paper should be considered as indicative rather than as definitive results for the two iron ore agglomeration processing routes considered.

Jan 1, 2006

The theme of the conference this year is diversification. One way to diversify is through acquisition. The principle underlying the winner's curse is that in competitive bidding situations where the value of the asset bid for is uncertain the winning bid will overstate the true value of the asset. The successful bidder is blessed with the winner's curse. What this paper will explore is to what extent this is true; how acquirers can avoid being blessed with the winners curse; and show how joint venture deal structures are used within the mining industry to avoid the winners curse.

Jan 1, 1996

By S H. Son, M K. Wang, H K. Jeong, B K. Cho, J I. Park

The utilisation of low-grade raw materials such as fine iron ore and semi-soft coking coal, and reduction of CO2 emissions are important issues in the ironmaking process. To solve these issues, a new process called PosPRA (POSCO prereduced agglomeration process) has been developing at POSCO. It focuses on the reduction of carbon composite iron ore briquette in travelling grate. In this study, the possibility of manufacturing the prereduced agglomerate (PRA) under oxidising atmosphere with travelling grate and the optimum manufacturing conditions of carbon composite iron ore briquette are investigated. The results have shown that controlling the temperature and oxygen potential in the range from 1100 to 1200°C and below 10 vol per cent respectively is very important to increase the reduction efficiency of briquette in travelling grate. High quality properties of the green briquette and PRA could be manufactured by using the briquette mixed with 20 wt per cent of coal under 0.1 mm in size under compacting pressure in the range from 3 to 7 t/cm. Adding 1 wt per cent water as a binder is proper under the condition of high compacting pressure. In a pot grate test, the compressive strength and metallisation degree of PRA are achieved over 150 kgf/p and about 55 per cent respectively, at bed temperature 1150°C and oxygen potential of 10 vol per cent when 20 wt per cent of coal is mixed in the briquette.CITATION:Wang, M K, Son, S H, Park, J I, Jeong, H K and Cho, B K, 2017. Development of prereduced agglomeration process using carbon composite iron ore briquette in travelling grate, in Proceedings Iron Ore 2017, pp 111–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The addition of cement to underground backfill at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited, Broken Hill commenced in 1967. A deterioration in metallurgical performance at each concentrator occurred as a result, with increased loss of lead and zinc to residues. Investigations to determine the reasons for this problem and methods to counteract it have been undertaken. This paper outlines the effects of cement on lead-zinc beneficiation at Broken Hill and presents an interim report on attempts to overcome the metallurgical deterioration.

Jan 1, 1971

The usual metallurgical, engineering and administrative activities associated with the handling and smelting of ores, and the subsequent handling and treatment of the products of smelting, present also problems of hygiene that engage the earnest attention of executives in all well-managed concerns.Again, associated with the employment of any considerable number of men, there is always present the problem of accident prevention.INDUSTRIAL HYGIENE.In the earliest records of lead min.ing and smelting there are references to the injurious effects of lead oh the health of the employees, and, with the advancement of medical science, lead poisoning has been the subject of many works by various authorities in many countries.Moreover, in practically every civilised country, there are laws governing the conduct of the lead industry, and in most cases these laws stipulate that employees shall receive compensation for disability caused by lead poisoning.This provision gives the problem an economic aspect. Apart from the legal and the economic aspects, however, there is the humanitarian aspect, which implies that the...

Jan 1, 1937

By H Jones

Closure cost estimates may be generated at any stage of a mining operationÆs life; commencing with the initial prefeasibility studies and continuing through to the final decommissioning cost estimates. However, not all mine closure cost estimates are necessarily the same. Cost estimates will vary depending on the purpose for which they are prepared, the organisations requiring or undertaking the estimate and the stage of the mining operation. Different organisations can legitimately arrive at disparate cost estimates for closing the same mine because the organisations have different reasons for requiring the estimates. Another, equally valid, reason for potentially wide variations in cost estimates by different organisations on the same mine site is the different definitions of æclosure costsÆ used by different estimators. This paper considers the different approaches by different organisations including operating companies, government authorities and financial organisations and uses a hypothetical example based on practical experience to illustrate some of these differences in estimation methods.The paper suggest that a more consistent approach to closure cost estimating in the Australian mining industry would assist mining companies, governments, the accounting industry and the broader community to better understand this complex component of mine planning. One possible approach to closure cost estimating is briefly outlined.CITATION:Jones, H, 2012. Closure cost estimation - All things to all men?, in Proceedings International Mine Management 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By B Morey, J Gordon, P Mackenzie

Mount Tom Price Mine is peerless amongst Rio Tinto iron ore resources around the world. It has provided Hamersley Iron with premium quality, high lump yield haematite ore over the last four decades. The Brockman type bedded ore, containing bands of haematite and shale of varying thicknesses has been traditionally bulk mined to either high-grade or low-grade based on alumina cut-off grades. As open pit mining has progressed deeper into the orebody approaching the keels of the megastructure, increased structural complexity, chemical and physical variations in the ore, unfavourable ore presentation and reduced blending options have become an issue for grade control and may have serious impacts on product stockpiles. The grade blocks and boundaries must be accurately defined according to geological contacts and where identified, selective mining may be applied. Therefore in-pit geological mapping is the definite and ultimate guide to achieve target grades and grade predictions. Under this scenario, it is absolutely vital that the mine geology team ensures this geological knowledge is passed onto the related departments including mining crews as well as to the short- and long-term planners.

Jan 1, 2002

By P Vass, C Butler, J Condon, B Hooper

DeGrussa Copper Mine, resource status 10.2 Mt at 5.7 per cent Cu, 2.1 g/t Au (Sandfire Resources, 2013), commenced concentrate production through its 1.5 Mt/a conventional copper flotation processing plant in September 2012. Geometallurgical assessment during the feasibility study identified potential process-critical ore factors that required further investigation to determine potential impact on processing. Ore characterisation and metallurgical processing performance test work of ore types ensued and subsequently, the first quantitative DeGrussa geometallurgy model was born. Now one year into steady state production, the geometallurgical program has evolved significantly from its infancy and provides valuable insight into ore characterisation and behaviour in the processing plant. This paper details geometallurgical investigations undertaken at DeGrussa to date; from feasibility metallurgical test work through to geometallurgical modelling and management practices, as well as reconciliation between observations at feasibility study level and subsequent observations in production.CITATION:Condon, J, Butler, C, Hooper, B and Vass, P, 2013. DeGrussa Copper Mine, Western Australia - feasibility to first production: a case study in developing a working geometallurgy model from first principles, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 59-66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

This paper provides an update to a paper by the author on an overseas explorer's perception of New Zealand, presented at the 1997 New Zealand Minerals & Mining Conference. New Zealand has one of the most open and internationally competitive economies in the world. The petroleum exploration industry in New Zealand is booming with a record number of wells planned for 2000. New Zealand is keen to encourage investment in mineral exploration to develop its natural resources. A study of the geological potential of New Zealand estimated the value of known and potential resources of metals at $86 billion. Gold has the greatest potential, with a total resource estimated at $33.5 billion. The price of gold has averaged NZ$554 since the beginning of 1998, and NZ$593 in the last year, which is very competitive with other countries. An assessment of country risk compared New Zealand with twenty other countries in ten risk categories: sovereign risk, land access, environmental issues, land claims, mining legislation, social risk, infrastructure, civil unrest, natural disasters and workforce. New Zealand ranked fifth, showing it has low country risk. This provides a high degree of certainty for investment, which is important for the perception of New Zealand as an exploration destination. Corruption was considered separately, and New Zealand ranked third out of ninety countries, showing it is one of the least corrupt countries in the world. New Zealand has a favourable business environment, good geological potential, low country risk and no corruption. Despite this, New Zealand has not registered on the radar screens of overseas mineral explorers, and the positive factors appear to have been overlooked. New Zealand has considerable undeveloped mineral potential, and with the current rise in commodity prices, it is hoped New Zealand can participate in a resurgence in mineral exploration.

Jan 1, 2000