Search Documents

By W Y. Kim, Y B. Kang, Y J. Park

The phase equilibria in the Al2O3–TiOx system were investigated in wide ranges of temperature and oxygen partial pressure: 1300~1600°C and 10-16.6~10-8 atm, respectively. The equilibrium phases and their compositions were identified using X-ray diffraction (XRD) and electron probe microanalysis (EPMA), respectively. Most noticeably, a wide range of pseudobrookite solid solution was found in equilibrium with almost pure alumina. At each temperature, the cationic ratio expressed as RTi = nTi/(nAl + nTi)) of the pseudobrookite solid solution showed a noteworthy dependency on the oxygen partial pressure. This resulted in the formation of a broad range of pseudobrookite solid solutions, ranging from Al2TiO5 (RTi = 1/3) to Ti3O5 (RTi = 1.0). Complete miscibility within the pseudobrookite solid solution was observed at 1600°C, with only a minor miscibility gap becoming evident below 1500°C. Based on the results obtained in the present study, the behaviours of Al2TiO5 pseudobrookite have implications in two key domains: (1) understanding changes in the physical properties of the materials, and (2) elucidating the evolution of Al–Ti complex oxide inclusions in liquid steel which can deteriorate the steel cleanliness.

Aug 21, 2024

Process mineralogy is an inter-discipline in the fields of mineralogy and mineral processing. As a predicting and trouble-shooting tool, process mineralogy helps address all mineralogical issues and problems related to mineral processing. It provides useful information on process design and optimisation, flow sheet development and cost reduction. As more and more complex and refractory ores are being discovered and processed, it is believed that process mineralogy will gain more attention and play a more important role in process design and optimisation. This paper will first discuss the scope of process mineralogy and mineralogical factors that may affect mineral processing of various ores, and then focuses on the application of process mineralogy in process design and optimisation through case studies.

Jan 1, 2008

By A B. Bayooke, A C. Robertson

In terms of underground tunnelling in metres advance per capita, Australasia compares well with the best world performers. This is because of the large number of metalliferous mines, coalmines and civil tunnelling projects, with the Australian tunnel advance for civil and mining projects exceeding 625?km/a. In terms of hard rock quarry extraction, Australia produces approximately 200?Mt/a of aggregates, roadbase, fill material and specialist rock products from its quarries, which equates to approximately 8?t/capita. Australian mining and tunnelling contractors are also of world standard and are used to excavating in a variable range of ground conditions in a competitive environment. One author has been involved in tunnel and underground space planning and quarrying in Australia for the past 25 years and predicts that, over the next 20 years, there will be a major swing towards underground space for commercial uses. This paper identifies the potential uses of underground commercial excavation and the planning and geotechnical challenges for the future. Underground quarrying creates new opportunities to extend existing quarries within their urban footprint with minimum impact on the surrounding community. Investigations by the authors reveal that there are very few cities in the world that actually incorporate underground space planning in their city plans. However, cities such as Helsinki have been planned in detail to utilise the rock resources beneath them. Brisbane is used as a case study for a practical application of commercial underground space and underground quarrying in Australia.CITATION:Bayooke, A B and Robertson, A C, 2014. Geotechnical challenges for underground commercial space and quarrying in Australia, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 317–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M I. Pownceby, N A. S Webster, J R. Manuel, J M. F Clout, E Donskoi, N A. Ware

The relative influences of sinter mineralogy, sintering temperature, solid and pore macro- and microstructure on iron ore sinter physical strength are not yet fully understood. Whilst a range of analysis techniques have been used by researchers to evaluate sinter physical properties and sinter mineralogy, none have been able to directly link sinter mineralogy and physical strength under controlled conditions. CSIRO has developed a unique laboratory method to study the fundamental melting properties of fine iron ores in a laboratory furnace under a controlled temperature and gas atmosphere environment designed to simulate the industrial sintering process. Compacted tablet samples for a 0.41 per cent and a 2.5 per cent Al2O3 series were fired in a tube furnace at various temperatures, cooled, then tumbled using a modified Bond abrasion test apparatus to determine a relative tumble index (TI) at each temperature. Quantitative XRD (QXRD) analysis was then carried out on the tumbled samples and optical image analysis (OIA) was conducted on polished sections of a separately fired compact in each case. The amount of total SFCA was found to decrease with increasing firing temperature for both alumina series with the total amount of SFCA higher in the 2.5 per cent Al2O3 series compared to 0.41 per cent Al2O3 series samples. The increase in the amount of magnetite and hematite with increasing firing temperature was largely at the expense of a decrease in total SFCA. Overall, there was good agreement between the quantitative mineralogy determined from QXRD versus OIA for SFCA, hematite and magnetite. Qualitative analysis of high magnification images of the sinter correlated with both the OIA and QXRD results.

Sep 18, 2023

By J Seppelt

The Kanmantoo Copper Project is owned and operated by Hillgrove Resources Limited and is situated in the Adelaide Hills region in South Australia. Mining in the area has taken place off and on over the last 140 years to recover metal from both copper and lead-zinc ores. This paper focuses on the commissioning, ramp up and future outlook for the copper concentrator at the Kanmantoo Copper Project with major focus on issues encountered and operating performance achieved to date.CITATION:Seppelt, J, 2012. Commissioning of the Kanmantoo Copper Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 127-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By S Mitra, D O’Dea, N Barrett, S, T Honey, M M. Hoque

The steel industry is currently exploring hydrogen-enriched blast furnace operations as a means to reduce the greenhouse gas emissions. However, there is a need to investigate the gas permeability behaviour of mixed burdens comprising of lump and sinter as the current knowledge regarding their behaviour is limited, particularly with regards to hydrogen enrichment. In the present study, a series of interrupted softening and melting (S&M) under load tests were carried out in a hydrogen rich gas environment (~15 per cent) in the temperature range from 1000 to 1300°C by placing different types of ferrous ore layer including Newman Blend Lump (NBLL), sinter and sinter-NBLL mixed burden in between two coke layers. X-ray computed tomography (CT) was then used to scan the interrupted test samples. Scanned images were first analysed using an image processing workflow implemented in ImageJ and the material simulator GeoDict (v2022) to segment different phases such as coke, ferrous and void based on their grey scale values. A quantitative analysis was then performed on the segmented images to estimate the phase volume fraction as well as bed permeability. Bed void fraction thus obtained agreed well with the bed contraction data obtained from the S&M test. It was further noted that both ferrous layer void fraction and bed permeability decreased linearly with increasing temperature for all ore samples. The mixed burden voidage changed in a similar fashion to the sinter, demonstrating a high temperature interaction between the two materials

Sep 18, 2023

By M E. Webb

Safety is a key value in most leading mining companies. Despite years of effort, and significant expense in ‘programs’, operating sites seem to have been left with no real improvement in either the elimination of fatalities or sustained reduction in injuries.Safety systems and processes have grown and evolved, often to the point where they have become overly complicated and marginally useful.MMG Limited, following the consolidation of its Australian operations under a single management structure, undertook a program to effect real and sustained change in its approach to managing safety. The program aimed at improving safety by better engaging its workforce and by making safety processes simple, useful and effective. It defined the role of the supervisor in creating safe work, the role of the people doing work and the role of safe work methods.A safety diagnostic tool was developed to assess site against safety-critical mindsets, behaviours, cultures and systems. The outcome of the diagnostic is considered by the organisation to be the true lead indicator of safety performance.While still a work-in-progress, the program at the Australian Operations of MMG Limited shows that challenging common paradigms in safety management can create real change in safety performance.CITATION:Webb, M E, 2016. Making safety simple, useful and effective, in Proceedings International Mine Management Conference, pp 217-223 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By S Benson

Staurolite is one of the major contaminant minerals contained in the Tiwest Cooljarloo orebodies. Approximately 80 per cent of staurolite in mined ore, reports to the heavy mineral concentrate that is supplied to the Dry Mill. Staurolite in heavy mineral concentrate is typically five per cent by weight and has no significant effect in the Dry Mill other than to occupy equipment space, reporting as a tailing, that requires transportation and disposal back to the mine site. Staurolite is an aluminosilicate with a MohÆs hardness of 7.5. It is known to have potential as an abrasive blast agent and it is produced in substantial quantities in the USA for that purpose. Research indicated that there was potentially a market for staurolite within Australia, as a replacement for some of the lower grade abrasives as well as a material of choice. A small tonnage of staurolite product was manufactured through a simple circuit within the Dry Mill in December 1998. This was subjected to industrial scale tests by external companies specialising in sand blasting. The most significant batch of tests were conducted at the Tiwest Chandala site on plant and equipment undergoing corrosion repairs. Staurolite was tested against three other commercially available abrasives and compared very well with respect to surface profile, surface texture, coating adhesive strength and dust generation. As part of a due diligence study, free silica, radiation and heavy metals contents of spent abrasive and dust was investigated. This information was needed to seek approval from the appropriate Western Australian statutory authorities to sell staurolite as a product. Approval was received in November 1999. Tiwest has since installed a production circuit in the Dry Mill capable of producing 20 000 tpa of Staurolite.

Jan 1, 2001

By R Bertuzzi

"This paper presents preliminary results of ongoing research being carried out at the University of New South Wales Australia (UNSW) into improved methods for estimating rock mass strength. In this paper the rock mass strength of Hawkesbury Sandstone is assessed. An estimate is first made based on an extensive database of intact rock strength data being collated by the author and the assumption that rock mass strength can be determined following the geological strength-index (GSI) approach. The resulting strength envelope is then compared with nine documented case studies where stress induced failure has occurred in tunnels excavated within Hawkesbury Sandstone. The case studies cover a range of conditions: construction dates from 1880s to 2006 spans from 3.2 to 12.5 m depths from 17 to 124 m excavation methods of drill and blast, roadheader and tunnel boring machine (TBM).Finite element modelling is used to assess the likely magnitudes of the principal stresses that were present at the time of the failures. The finite element models are interrogated to provide the values of major and minor principal stresses in and around the mapped failure zones. Failure and stable points are then compared to the proposed strength envelope(s) of Hawkesbury Sandstone derived using the Hoek-Brown and the spalling criteria. The ability of the Hoek-Brown rock mass strength criterion to differentiate between the ‘failed’ and ‘stable’ zones is considered to be remarkable.CITATION:Bertuzzi, R, 2014. Estimating the rock mass strength of Hawkesbury Sandstone, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 417–424 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By T D. H McGrath, R Byleveld, W P. Staunton, J J. Eksteen

"The Gold Technology Group at Curtin University through the AMIRA P420 series of projects has recently developed the integrated liberation leach model (ILLM) for optimisation of gold plants. The model encompasses recovery by both gravity (batch centrifugal concentrators or BCCs) and leach adsorption (CIP/CIL) circuits. The ILLM essentially combines the Group’s well-known standalone models (ie gravity and SIMCIL) to create a robust simulation package.The ILLM process model provides a tool for sites to determine optimum set points for operations to optimise recovery (eg target grind size). It can also be used to predict the effect on gravity recovery, leach recovery and overall recovery when changes are made to circuit design, either temporarily (eg a leach tank taken off-line for maintenance) or as part of a circuit expansion (eg expanded gravity circuit capacity, or addition of leach tank capacity).This paper discusses the capability of the ILLM process model by highlighting a recent case study. The paper also addresses the test work and plant data required as model inputs, as well as limitations and the application of the ILLM to greenfield projects.Citation:McGrath, T D H, Staunton, W P, Eksteen, J J and Byleveld, R, 2016. Application of an Integrated Liberation Leach Model for Process Optimisation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 173–178 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S M. Gover

Estimating the probability of failure for embankments is not intuitive. It requires not only an appreciation of the strength of the embankment, but an understanding of the variability and uncertainty in the strength parameters as well. These additional aspects are, in themselves, relatively new to most practicing engineers, and therefore require some discussion.This paper discusses the concepts of probability and uncertainty, and presents a reliability-based numerical experiment, together with a literary study and collation of some of the author’s historical slope stability analyses, to investigate whether a direct relationship between safety factors and probabilities of failure exists for certain levels of uncertainty in strength parameters. In doing so, a useful tool is presented whereby knowing the safety factor of a simple slope or embankment with a consistent level of uncertainty, one can infer an approximate probability of failure.CITATION:Gover, S M, 2018. Linking safety factor to probability of failure, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 384–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By T A. Carter

In 2010 Agnew Gold Mine (AGM) struggled to produce the required tonnages from its stopes. The longhole rises used to create void in stopes were unreliable and often failed to gain the designed rise height. The number of firings per stope was having an adverse impact on the ground conditions at the stope brows, impeding stope productivity.Through practical experimentation with longhole drill rigs, box hole rigs and development drill rigs as well as trialling new methods in conjunction with reviewing drill hole data, drill hole accuracy was observed to be an issue on-site. Innovative dragging methods such as the reverse drag, combined with a slope instead of a vertical face on the rear of stopes, have improved dragging and a reduction of firings per stope, enabling larger production blasts.The methods trialled and subsequently implemented at AGM have facilitated the mine achieving budgeted targets for six consecutive quarters. This paper documents the use of these methods in a key lode of AGM’s operations to improve drill and blast practices in order to achieve production targets.CITATION:Carter, T A, 2014. Improving production drilling and blasting in the Kim South orebody at Agnew Gold Mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 251–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By K Tanguturi, B Belle, R Balusu

Management of high rates of goaf gas emissions between 4000 and 6000 L/s of methane gas in longwall panels is a challenging issue, particularly in start-up areas of the panels. There is a need for investigation of the effect of various goaf gas drainage concepts and techniques, and development of effective gas drainage strategies for management of high goaf gas emissions in start-up areas of the longwall panels. This paper presents the results of various computational fluid dynamics (CFD) simulations that were carried out to investigate the effect of different goaf gas drainage strategies and combinations for gas management in the start-up area of the longwall panels. Results indicated that the gas (methane) concentration in goaf holes on the tailgate (TG) side vary between 50 and 75 per cent under the simulated field conditions with flat coal seam gradients. The results also indicated that operation of more goaf holes for draining the goaf gas on the TG side results in high ingress of oxygen and further reduction in gas concentration in goaf gas drainage holes. The simulations also included scenarios with goaf gas drainage holes on the maingate (MG) side, TG cut-through seal and near the start-up area. This paper presents the results of various goaf gas drainage strategies and discusses the effect of various combinations in order to develop effective goaf gas drainage strategies for gas management in start-up areas of the longwall panels.CITATION:Tanguturi, K, Balusu, R and Belle, B, 2015. Development of goaf gas drainage strategies for start-up areas of highly gassy longwall panels, in Proceedings The Australian Mine Ventilation Conference, pp 251–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J Jackson, K Nguyen, A Nguyen, E Manlapig

"With the recent advancement in drill core imaging systems, a large volume of high resolution drill core images can now be rapidly collected and mineralogically classified. This paper introduces a novel semi-automated method for rapid prediction of process engineering parameters from this type of image. The aim is to allow for a rapid and low-cost assessment of the ore processing variability within a mineral deposit with a reduced amount of metallurgical test work. This method will see its application primarily in the project evaluation phase, where proper evaluation of the processing variability of the orebody normally requires a prolonged and costly metallurgical test work program. Applying this image-based texture analysis method on the mineralogical classified drill core images, the ores are classified according to their textures. For each engineering parameter, a small number of physical test work is required to produce a data set for training and testing of the predictive model. The paper also presents a case study in which this method has been applied to predict the A*b parameter used in mineral process plant design.CITATION:Nguyen, A, Jackson, J, Nguyen. K and Manlapig, E, 2016. A New Semi-automated Method to Rapidly Evaluate the Processing Variability of the Orebody, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 145–152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By A Clarkson

Cannington Mine is an underground silver lead zinc operation located in north-west Queensland which has been in production since 1997. Ore is primarily moved through an underground material handling system comprised of a crusher, conveyor and hoisting shaft. The Fowler Shaft was constructed in 1997 using a strip and line method with the intent for it to provide a means to hoist ore from the loading station 600 m below surface. The shaft also serves as the route of key services including high voltage power, mine dewatering and fresh air. Despite the adherence to a mining exclusion zone, large-scale change in geotechnical conditions around the shaft were first observed in 2015. Ongoing ground movement around the shaft lead to cracking and delamination of the concrete liner. Shaft management required the on-site team to measure deformation rates and magnitudes, forecast change, manage rockfall risk and deforming pipework, and ultimately, hoisting skip clearance. Monitoring techniques to observe and measure deformation were required to evolve with the magnitude of movement. Some techniques leveraged off modern technology while some of the most useful techniques were based on logic and first principles. All shaft deformation management strategies relied on the co-operation and alignment between Cannington’s Infrastructure Maintenance, Survey and Geotechnical Departments.

Mar 29, 2023

Vertical retreat open stoping (VROS) is a variation of sublevel open stoping (SLOS) that has been introduced at Cannington to minimise the influence of subvertical geological structures during stope extraction. The first application of VROS is described, where structures within the stope resulted in a change in firing sequence and the extraction of two complete sublevels in a single blast. The use of electronic detonators is critical to the success of VROS and their application is described. Numerous benefits of using VROS have been identified and are described. To date, eight stopes have been successfully mined using VROS. In addition to the first application of VROS, two further case studies are described.

Jan 1, 2005

This paper presents a rationale for selecting appropriate support elements which combine to form a support system to maintain stability in mines subjected to both strainburst and the shaking that occurs from fault slip. The overall approach was developed during the 'case for safety' study undertaken to allow the then Beaconsfield Gold mine (now Tasmania mine) to resume development and production after the 25 April 2006 ground-fall and fatality that received worldwide publicity. Issues of the sometimes competing requirements of support element performance during dynamic loading are discussed and the need for support flexibility is contrasted with the usual high support element stiffness required when these are used to reinforce rock masses. An example is presented to show the steps and technical details required to design each component of a support system to counter the de-stabilising effects of seismicity.

Nov 25, 2010

By T P. Medhurst

In many cases mine design is the most important driver of the profitability of a mining project, however to reach an æoptimumÆ mine plan many compromises have to be made. Some of the fundamental profit (and loss) drivers relate to stoping methods and stope design parameters. Inevitably trade-offs have to be made between the stability of underground openings, ground support costs and production efficiency. This paper looks at the role of geomechanics in the mine planning and design process. The concepts of æcontrollable lossesÆ and æuncontrollable lossesÆ are developed as a means of partitioning ground control costs. A stope design example is given which provides a method of examining mining costs, and includes a decision making element in order to quantify geotechnical impacts and select stope dimensions. The method also provides a general framework as a means of balancing ground control costs against maximising returns from an underground mining project.

Jan 1, 2000

By M Darvall

Magnetite ore blending has yielded signifi cant performance improvements in OneSteel’s magnetite concentrator. The magnetite concentrator beneficiates magnetite ore from the Iron Magnet Deposit and produces concentrate, which is pelletised, then fed to the OneSteel Whyalla blast furnace. Concentrator feed variability severely detracts from the concentrator’s performance, affecting both concentrate yield and grade, which impacts on all downstream processing costs.A coordinated approach has integrated mine planning, geological modelling and grade control, to minimise concentrator feed variability, through effective ore blending throughout the mining and stockpiling process.Mine planning personnel design shots that extend the full width of the orebody and hence across the stratigraphic profi le. Based on geological information contained in block-outs and in consultation with Geology, the Grade Control team allocates material to each primary stockpile, potentially from every stratigraphic domane in the orebody. This ensures primary stockpiles are designed with maximum practical homogeneity and consistency.Using only primary movement, the allocated ore is stockpiled in a layer-cake fashion. The ore is pimple dumped across the width of the stockpile footprint and on completion of a layer, it is dozed flat with an access ramp that allows dumping to commence on the next lift. The primary stockpiles are reclaimed normal to build direction and the magnetite is crushed, all in, to a concentrator feed stockpile.The ore is sampled at the crusher from a falling stream cut. These assay data, are used for benchmarking and control charting the grade and variability of concentrator feed stockpiles. The concentrator feed stockpiles have demonstrated a statistically signifi cant reduction of within pile variation, between pile variation and pile to pile variation, primarily attributable to the development of ore blending. The concentrator has seen sustained, improved performance as a direct result, which translates into lower concentrate cost per tonne and improved yield and quality.

Jul 11, 2011

By J P. van Dyk

A new crude ilmenite beneficiation process was recently proposed that allowed for the preparation of a smelter grade ilmenite from ilmenite with elevated chromium content. Magnetising roasting was not utilised in the process. As part of this circuit an ilmenite low susceptible reject stream was produced that had a low magnetic susceptibility. In this article a magnetising roasting process was investigated to beneficiate this material. Tests were conducted on material produced by pilot scale simulations on a typical South African East Coast heavy mineral reserve. The results obtained were compared to those published in literature for crude ilmenite. The small-scale experiments were used to define approximate operational limits for the oxidising roasting of a low susceptible ilmenite low susceptible reject stream, although industrial roasting conditions may differ significantly from those obtained in laboratory units. In a next phase these results will be confirmed on pilot plant scale.

Jan 1, 2001