Search Documents

By Milawarma E, Cusack C

The Sapan Dalam coal deposit of Indonesia consists of ten steeply dipping seams with thicknesses varying between 0.1 and 3.5 m and split by shale, clay, silt and sandstone. The area contains four faults dipping about 75¦ with four to 85 m vertical displacements. The complex nature of the deposit coupled with limited 27 exploration drillholes at an average spacing of 200 m made it difficult to create a realistic geological model. A three-dimensional gridded seam model gave a fair representation of the deposit. Attempt to create an optimum pit using the WHITTLE 3D pit optimiser proved unsuccessful since the pit optimiser is restricted to standard regular or fixed blocks. The gridded seam model was converted to a fixed block model prior to the optimum pit design. Smoothing and pit base controlling were also introduced to obtain a smoother pit. A mining scenario produced 3.6 million tonnes of coal, 28.4 million bcm of waste and US$18.1 million revenue.

Jan 1, 1995

Western Mining Corporation began shaft sinking operations at it's Foster orebody, south of Kambalda, on the 20th June, 1984. The top levels of the orebody are currently being mined via a decline some 1.5km away.Long term plans require the shaft and decline to combine and produce 400,000 tonnes of nickel ore per annum. Eventually all of the ore produced will be hauled up the shaft.The shaft is 4.5m in diameter and the target depth is 760m. Ground conditions to date suggest there will be no further need for concrete lining beyond the oxidised zone. As such, the sink is an open-shaft development in competent basalt rock. Shaft furniture will be installed on completion of the excavation to the target depth.This paper summarises the experience in the project to date, along with comparisons to conventional shaft sinking methods employed in previous years at Kambalda Nickel Operations.

Jan 1, 1985

The Honeymoon Well nickel sulphide deposits are located in the Agnew-Wiluna greenstone belt, about 45 km south of Wiluna. Both disseminated and massive sulphide nickel deposits are hosted by komatiitic rocks within the deformed and metamorphosed Honeymoon Well ultramafic complex. Fresh ultramafic bedrock is covered by up to 50 m of highly conductive transported material which greatly hampers both exploration and understanding of the bedrock geology. In the early-1970s, mineralisation was discovered by diamond drilling geochemical anomalies defined by wide-spaced percussion drilling over ultramafics that had been outlined by ground magnetics. Subsequent drilling has defined a resource of 158 Mt at 0.71 per cent nickel (based on 0.4 per cent nickel cut-off, 300 m below surface, December 1995) in four deposits. Over the life of the project a wide range of geophysical techniques have been used including airborne and ground magnetics, time domain clectromagnetics (EM), induced polarisation (IP)/resistivity, gravity and downhole techniques including EM, IP and physical property Measurements.

Jan 1, 1996

By Eggins SM, Crawford AJ, Wallace ME, Falloon TJ

The Earth's Upper Mantle is dominantly peridotitic but in convergent margin regions, such as the S.W. Pacific, subduction of oceanic crust gives greater chemical and petrological diversity to upper mantle petrology and petrogenesis. Examination of currently active, Quaternary and Tertiary volcanism in the S.W. Pacific, particularly seeking information from ocean floor sampling to characterize the basement to island arcs and to investigate active spreading centres, consistently points to parental magmas of basaltic to picritic character. However, these parental magmas are chemically diverse and it is not possible to designate a characteristic 'island arc' or 'convergent margin' petrogenesis in the sense of a characteristic mantle source composition and a charactistic partial melting regime. In this respect, magma genesis at convergent margins contrasts with that at oceanic spreading centres. Our studies emphasize the importance of source peridotite ranging from 'fertile lherzolite' (i.e. compositions with 3-4% CaO, A12O3, 0.3-0.5% Na2O) to refractory harzburgite (

Jan 1, 1987

The Mt Leyshon Volcanic Complex lies 24 kilometres south-west of Charters Towers and is part of a major continental volcano-plutonic province of Permo-Carboniferous age in north-east Queensland.The volcanic complex is located on the contact between Cape River Beds of Cambrian age and the Ordovician Ravenswood Granodiorite Complex. The emplacement of the complex appears to have been structurally controlled and is at the intersection of major north-east and minor north-west trending lineaments. The gold mineralisation occurs in the form of cavity coatings, matrix replacement, disseminations, and vein and fracture fillings containing quartz, chlorite, carbonate, pyrite, sphalerite, chalcopyrite and galena in various volcanic breccias and rhyolitic intrusives. The current published mineable ore reserves, calculated by Noranda Australia Limited, are 6.3 million tonnes of 1.8 grams per tonne gold and 4.8 grams per tonne silver. The orebody is open at depth, and in all directions except north where it abuts the granodiorite.

Jan 1, 1986

By Walton M. C

A combination of flotation and smelting technologies is proposed as a cost-effective means to maximise the revenue of base metal operations. The proposed treatment route breaks the grade - recovery nexus associated with the treatment of ores exhibiting difficult mineralogy in conventional plants. Aspects of the two technologies are reviewed and typical capital and operating costs presented. A significant improvement in revenue is demonstrated in a worked example, where a copper-lead-zinc operation is examined in terms of the conventional and proposed treatment options. For the selected ore, the net smelter return per tonne of mill feed improved 57 per cent, from US$89.70 to US$141.10 with the proposed treatment option. This represents an additional US$51.4 million in annual revenue. Metallurgical operating costs increased by US$20.12 per tonne of mill feed for an incremental capital requirement of US$30.3 million for an existing operation.

Jan 1, 1992

By Offler R, Lau J, Lea J. F

The stratiform and vein-type pyritic silver-Iead-zinc-copper sulphide deposits of Sunny Corner, NSW are hosted by acid volcanic and clastic sedimentary rocks of Middle Silurian to Early Devonian age. The rocks have been subjected to low-grade regional metamorphism (prehnite-pumpellyite facies) and three phases of folding and four faulting events are recognised. Pyrite is intensely fractured, indicating brittle deformation. Chalcopyrite and galena exhibit deformation twins and slip planes indicating ductile deformation; sphalerite and chalcopyrite show straight and curved grain boundaries and dihedral angles of 120° as evidence of annealing recryslallisation. Sulphur isotope ratios for 22 samples from five deposits range from 1.7 to 10.7 per mil and average 7.4 per mil. Sulphur isotope data are similar to those from other stratiform sulphide deposits in acid volcanic rocks of Late Silurian age in the eastern Lachlan Fold Belt, especially Woodlawn and Captains Flat and together with other features of the mineralisation, suggest a volcanic exhalative origin for the Sunny Corner deposits.

Jan 1, 1984

Laboratory studies of batch and continuous screening of ferrous sinter mixtures (4-0.5 mm) are described. The results are analysed by an equation derived from the first-order rate law for the condition of decreasing screen residue.The results of the studies show that the two screening operations are comparable in all respects if deck length in continuous screening and time in batch screening are interchanged.It is shown that the general screening process is determined by the numerical values of the screening rate constants of each of the particle sizes in the feed mixture and that the relationship between these constants and the particle size/screen aperture ratios is related to the appropriate probability function of the same ratios.It is also shown that the screening rates decrease exponentially with the amount of near-mesh material present in the feed and that oversize particles can increase these screening rates for some screen motions and decrease them for others.

Jan 1, 1985

The Vertical Crater Retreat (VCR) mining method was used to mine two rib pillars at New Broken Hill Consolidated Limited (NEHC) mine at Broken Hill. Experience gained in a trial VCR pillar stope was applied to the design of Panel 3CN pillar (P3CN). Restricted access and a central sandfilled plug in this pillar necessitated the use of angled blastholes and blasting of the stope in two sections. Borehole surveys and close charging supervision were necessary to block, charge and stem the spherical charges in the correct position. The laver sections of the VCR stope with rock walls attained an average slice advance of 2.2 m whereas the higher section of the st.ope between cemented fill walls attained an average slice advance of 3.4 m. Achieved fragmentation was extremely fine. External dilution was assessed at less than 10 per cent. A cement consolidated sandfill exposure of approximately 1300 m2 stood vertically with no significant slumping.

Jan 1, 1983

By Rashad MZ

The evaluation of ore deposits consumes much effort, cost and time, hence research work must aim to minimize these inputs with no loss of accuracy. The present study is devoted to assess the optimum conditions and methods of calculations which give minimum costs of ore exploration. An area of (a x a) where "a" is the zone of influence of the semi-variogram, i.e. (2800 x 2800 square metres) located within the Abu Tartur plateau is the subject of the intensive study. The distances between boreholes are varied ie. a/4, a/6, a/8 and a/ 10 respectively. The average ore grade (G), thickness (t) and relative ore reserves (tG) are calculated by four methods. The results indicate that at a distance equal to a/5, the inverse distance squared method gives the best results. These parameters save about 50 percent of the cost of exploration with a map accuracy greater than 90 Percent.

Jan 1, 1987

The paper highlights the conceptual developments in rock mechanics applied to quantify the effect of bolts in the stabilization of joints and yielding soft rocks. NOTATION Aa = stress change after excavation Eä EE, Eä = moduli of intact rock, single joint and jointed rock Eb = elastic modulus of the bolt k, = normal stiffness of joint Ab = cross section area of the bolt A, = area of influence per bolt ab = axial bolt stress e, = axial strain of the bolt eä e,, ej, = strains of intact rock, joint and jointed rock Ai = area of the joint ,r+ = shearing resistance of the bolt (at the joint) a = normal stress at the joint plane aäa3 = major and minor principal stresses c;, 4i; = cohesion and friction angle of the joint 0 = angle between the bolt and the joint a = inclination of the joint to the vertical axis P = bolt density parameter u, = convergence of unsupported tunnel section u, = convergence of bolted tunnel

Jan 1, 1992

Major exploration companies can have a problem with what to do with small precious metal ore bodies located through exploration programmes. Low tonnage, but high grade, ore bodies too small to justify in-house development.1.2 Ban Ban Mining is a Sunshine Coast based partnership with considerable expertise in mining and earthmoving which specializes in the mining of small/medium size ore bodies on behalf of the tenement holder on a profit sharing or royalty basis.1.3 The partnership's first successful venture has been the mining and vat leaching of a small 40,000 tonne ore body with a head grade of 5 gm/tonne gold and 32 gms/tonne silver, situated near Ban Ban Springs in southeast Queensland.1.4 This paper looks at the low cost vat leaching method of treatment, as an alternative to CIP and CIL in the processing of low tonnage/high grade precious metal ore bodies.

Jan 1, 1990

By Elford H. S, Hughes J. F

The object of this paper is to bring before Members of the lnstitute the very important and much discussed question of scientifically prospecting for ores, oil, coal, etc.The paper is divided into three sections:SECTION l - Description of Geophysical Prospecting methods.(1) Sound-Vibration.(2) Magnetic.(3) Gravitometric.(4) Electrical.(a) Equipotential.(b) Electro-magnetic.(c) Schlumberger.(d) General.SECTION II - General discussion of Cicophysical Prospecting.SECTION III - Appendices.(1) Systematic summary of methods of survey.(2) Table of electrical conductivities.(3) Bibliography.SECTION I - DESCRIPTION O:F GEOPHYSICAL PROSPECTING METHODS.(1) SOUND-VIBRATION.THE transmission of sound waves or vibrations underground will depend on at least three factors: (a) Type of Rock. - Hard, dense rocks wiII transmit sound waves much more quickly than softer, more porous rocks. In the former the speed may be eight times that of the latter.(2) Uniformity of Rock. - Any variation in the texture, hardness, etc, wiII have an effect on and direction of transmission of the waves.

Jan 1, 1927

By Hendrix JL, Nelson JH

Three ores (sulfidic, oxidized and carbonaceous) were analyzed to determine the effects of leaching time, ore depth, and ore mineralogy on cyanide species concentration. NaCN solutions were percolated through opaque columns filled with milled ore. Column design made liquid sample collection possible from various depths at specific times. The concentrations of weak acid dissociable(WAD) and total cyanide, Fe(CN)63 , Fe(CN)64 , SCN , and Cu(CN)43 were determined for each sample. Extended percolation time led to increases in WAD cyanide concentra- tions and decreased SCN and Cu(CN)43 concentrations regardless of ore depth. WAD cyanide concentration decreased while Fe(CN)64 concentra- tion increased with ore depth. Highest concentrations of Fe(CN)64- SCN and Cu(CN)43 were found in the sulfidic ore, with expected low WAD cyanide concentrations. Lowest concentrations of Fe(CN)64 , SCN 3 and Cu(CN)4 were found in the oxidized ore. Intermediate concentra

Jan 1, 1988

By R Milton, D Hake, H Sprague

The North Western Sewer tunnel extends over 11.5 km in the North Western suburbs of Melbourne.The $253 million tunnel project provides a critical link in the Melbourne Sewer Network. The existing sewers fail to service the increasing demands of the growing population of the North West regions of Melbourne. This project will protect the environment and improve the standards of service of the existing system. This paper concentrates on Section three of this project, consisting of the final 4 km of the Contract, three access shafts and a cut and cover section of tunnel.Transfield Tunnelling as Head Contractor constructed the tunnel for Melbourne Water Corporation, with Enetech Streamline, formally Streamline Australia, a trading arm of Melbourne Water acting as Superintendent.Excavation of Section three of this project commenced in September 1994 and project completion is scheduled for October 1998. The tunnel passes below the residential suburb of Essendon, through some of the most challenging ground conditions ever attempted to be tunnelled in Australia.

Jan 1, 1999

By Hosking IA, Mirkov P

Among the solutions currently being considered for improving traffic flow in Sydney are the construction of major road tunnels, principally the Eastern Distributor Tunnels, leading from the end of the Cahill Expressway to Drivers Triangle and South of Taylor Square and the Sydney Harbour Tunnel, which incorporates sections of driven tunnel at the northern and southern sides of the harbour. The Eastern Distributor Tunnels, known as Stages 2 and 3 of the Eastern Distributor Scheme comprise: Stage 2 - A south bound two lane tunnel from north of William Street to Driver's Triangle. The southern end includes two Y junctions (locally 3 to 4 lane widths) with exits into South Dowling Street, Anzac Parade and Moore Park Road. Stage 3 - A north bound, two lane tunnel from Taylor Square to Palmer Street just north of William Street. Further details of the Eastern Distributor Tunnels are given in the paper by Baxter, Chappel and Fishburn (1986) which is included in this conference.

Jan 1, 1987

The Copper Concentrator at Mount Isa Mines Limited treats approximately 6 Mt of chalcopyrite ore annually. The ore is currently sourced from the 1100 and 3000 orebodies at Mount Isa. Chalcopyrite is the only significant copper bearing mineral, with pyrite, quartz and dolomite being major gangue minerals. Ore is typically 10% chalcopyrite, 11% iron sulphides and 79% non-sulphide gangue. Copper ore is treated through two autogenous mills, two ball mills and a flotation circuit. The autogenous mills replaced a crushing plant, two rod mills and two primary ball mills during 1991. For routine analysis of concentrator performance, composite samples of mill feed, final concentrate and tailings are generated every 4 week period. All samples are sized and size fractions are assayed. Recovery of mineral species to the concentrate are then calculated for each size fraction. Sometimes liberation analysis was also performed by QEM*SEM (Quantitative Evaluation of Material by Scanning Electron Microscope).

Jan 1, 1990

Any project carries a number of challenges and risks. Inappropriate design, poor project management, time, industrial disputation and capital over runs are all areas which can impact on a project cash flows and return on investment. In the resource Industry you have the added complexity and risk of geology which is difficult to predict and sometimes unforgiving. The Dartbrook Mine was designed and constructed as a high output longwall mine and has overcome a number of hurdles to produce over 2.3 million tonnes for the first year of operation. A number of problems were encountered during construction which resulted in the inseam development being delayed for six months. Dartbrook people have demonstrated they can manage adversity and produce world class results. The mine has been through a very steep learning curve during 1997 and with this experience behind the mine is now producing at an annualised rate of 3.4 MTPA.

Jan 1, 1998

Polyacrylamide flocculating agent has been used in the Leaching Division of the Risdon Works of the Electrolytic Zinc Co. of Australasia Ltd since October, 1960. Since the introduction, the.: number of thickeners in use in the continu-ous thickening stage has been reduced from eight to three; there has been an increase of 25% in throughput and a reduc-tion of solids in.:thickener overflow from 3-4 gòpòl . solids to 0.5 g.p.l. solids. Reagent addition has been at the rate of 0.25. lb SEPARAN, NP10 per ton solids.Additionally there has been a gain of 3% in current efficiency as the direct result of the addition of SEPARAN NP10 to purified cadmium sulphate solution prior to electrolysis for cadmium metal. A smoother deposit has resulted and it has been possible to increase deposition time between strip-pings from 47 to 71 hours. However, there has been a slight increase the lead content of the cadmium-metal produced.

Jan 1, 1963

By S B. Martin, M P. Simpson, J L. Mauk

The Martha deposit in Waihi, New Zealand, is a giant adularia-sericite epithermal gold-silver deposit that formed 6.0 to 6.1 Ma, and has produced over 6.4 Moz gold and 39.9 Moz. Fluid inclusion analyses were undertaken on a limited number of vein samples from Martha. The results from this eight week student project are preliminary but agree with previous studies. There is little variation between primary and secondary inclusions and between different vein types, except that homogenisation temperatures of the inclusions in sphalerite grains are on average 20¦ to 30¦C higher than the average quartz vein values. Overall the temperatures of homogenisation ranged from 182¦ to 258¦C and final ice melting temperatures ranged from 0.0¦ to 2.8¦C. Unusual black inclusions were also found associated only with the ginguro bands. Some of these appear to be solid sulphide inclusions but others are not so clear.

Jan 1, 2007