Search Documents

A new plant for grinding limestone was built at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited to meet increasing process demands expected to reach 150 tonne/day of ground limestone. Plant specifications included open- circuit wet grinding, a single ball mill, a feed sizing of minus 6 Tyler mesh, a product sizing of 100 per cent minus 200 and 95 per cent minus 325 Tyler mesh and for the plant to be unmanned during normal running. Main features of plant and equipment are described; grinding performances given, as well as operating experience since commission- ing of the plant in March, 1976.

Jan 1, 1977

By Rongqing Q, Tiancong Z, Yiyuan L

The influence of pulp density, ferric ion concentration and particle size on the tank bioleaching of two kinds of refractory gold concentrates are discussed. The chemistry and mechanism of the bioleaching process are also presented. The relationship between oxidation of sulphides, liberation of enclosed gold and gold cyanidation are discussed. The consumption of NaCN could be reduced by alkaline treatment of bioleached residues prior to Cyanidation.

Jan 1, 1992

The P49 Shaft, Hilton Mine, was sunk and equipped for Mount Ise Mines Limited by con- tractors Cementation - Thiess Joint Venture. The leached siltstones to a depth of 150m were known to contain large volumes of water. These siltstones were cored and tested in the laboratory. Field results confirmed that cement grouting was relatively ineffective but that chemical grouting was effective. The Sm diameter shaft was sunk to a depth of 1040m. Weak strata to the full depth re- quired continuous temporary support by rock bolts and mesh before the concrete lining was poured, and made sinking conditions difficult. After completion of the shaft sinking the headframe was redesigned and modified to allow shaft equipping as a combined service and hoisting shaft with seven compartments. The shaft steelwork was designed and fab- ricated for service with high speed conveyances operating under corrosive conditions. The steelwork, weighing approximately 1500 tonnes, was installed to a high degree of accuracy which required guides not to depart from true verticality by more than 2mm over any 5m, or 15mm over the full shaft depth.

Jan 1, 1976

By K Uchino, M Inoue

Self-potential anomalies are generated by fluid pressure gradient, by temperature gradient or by chemical gradient. On the basis of this principle, a new technique is proposed to locate the fire source of spontaneous combustion of coal by the self-potential method. In order to investigate whether this method can be applied to locate the spontaneous combustion of coal in practice, surveys of self-potential distributions were undertaken in a coal waste pile undergoing spontaneous combustion. The results showed that there is a negative centre of the electrical potential distribution in the measurement area. The potential in this centre is about 140 mV lower than that in the surrounding area. Moreover, the negative centre of electrical potential distribution almost overlaps with the high temperature zone. Therefore, it is concluded that it is possible to locate the heat source by the measurement of self-potential distribution.

Jan 1, 2005

By Carlie JC

Many low sulphidation epizonal gold and zinc-lead vein deposits within magmatic arcs are situated on basement highs, and post-date both the main volcanic episode and porphyry copper (gold) mineralization. These features are best explained by emplacement of a flat batholith a few kilometres beneath each mineral district, as recently demonstrated by geophysical data in the Baia Mare district of Romania. The batholith provides heat for the hydrothermal system, and results in extensional faulting both through up-doming of the overlying rocks, and in some arcs through incipient collapse of the thermally weakened crust under regional extensional stress. More water-rich magmas emplaced at greater depths could explain some deep epizonal and mesothermal gold deposits situated outside magmatic arcs.

Jan 1, 1995

Australian continental crust has accreted and consolidated by thirds: 1/3 during Archean time, 1/3 during Early to mid- Proterozoic time, and 1/3 during latest Precambrian to mostly Paleozoic time. The progression of orogenic systems and the crustal consolidations they represent seem not fundamentally different in basic orogenic processes from better known Mesozoic-Cenozoic examples in that accretionary, continental margin, collisional, and intraplate intracratonic inverted and/or reactivated systems are all recognizable in the tectonic evolution of Australia.

Jan 1, 1995

By Andrew R. L

The Kintyre uranium deposit was discovered in 1985 in the course of following up radio- metric anomalies generated in an earlier air- borne survey. The latter survey was conducted primarily to acquire aeromagnetic data for diamond exploration and the uranium discovery was made during a subsequent campaign of base- metal exploration. CRAE commitment to the Rudall area for a range of commodities over a period of 13 years made a significant contrib- ution to the discovery of Kintyre. Other con- tributing factors included CRAE's multicommod- ity approach to exploration, management support and continuity in the geological team. The Kintyre uranium deposit (Fig. 1) is located on the northern margin of the Rudall Metamorphic Complex, 60 kilometres south of Telfer and 260 kilometres north northeast of Newman, in the Paterson Province of northern Western Australia. It is 700 metres inside the northern boundary of the Rudall River National Park (15695 sq. km) and lies between the Great Sandy Desert and the Little Sandy Desert (Beard, 1969). Intense weathering since the Permian has produced a subdued landscape around the deposit. Resistant rock types still retain an older plateau surface but it is incised by more recent streams. Other Proterozoic and Permian rocks form low, sometimes rocky, areas largely covered by aeolian sand.

Jan 1, 1988

The Charters Towers 1:250 000 Gravity Data Set represents a new initiative of the Department of Resource Industries (DRI, formerly Queensland Department of Mines) to provide high quality regional gravity data over areas of the State that have high potential for new mineral discoveries. The Department has adopted a strategy to upgrade geophysical data to complement the ongoing Regional Geological Mapping Program (RGMP) of this Department and in areas where the data would be of most benefit to the mineral exploration industry. Part of this strategy is to ensure that these data are released within 6 months of data collection.The 1989 Charters Towers survey was completed as a joint project with the Bureau of Mineral Resources, Geology and Geophysics (BMR), and is the first regional geophysical data acquisition project undertaken by the DRI. Prior to this survey, the only gravity data in this area dates from the B MR regional surveys carried out between 1960 and 1967.

Jan 1, 1990

By Nash B. G W

In June 1976 a 600'tonne/day manganese ore sinter machine, with on-strand cooling, was commissioned at the plant of Tasmanian Electro Metallurgical Company Pty. Ltd. at Bell Bay, Tasmania. This machine was installed in order to utilize manganese lump ore screenings generated in the preparation of raw materials prior to charging to the electric smelting furnaces at Bell Bay. Since commissioning, trial sintering of a number of different grades of manganese ore fines from Groote Eylandt Mining Company Pty. Ltd, has been conducted and suitable sinter has been produced from these different grades. The sinter produced is used as part of the furnace burden in both ferro manganese production and silico manganese production. The inclusion of sinter as part of the charge in the production of ferro manganese has considerably improved furnace operating conditions and performance.

Jan 1, 1977

By Mansor A. N

Results are reported for the computer simulation of heap leaching of mixed copper oxide and sulphide ores. They resemble those obtained from testwork in terms of a substantial peak in the copper concentration of the pregnant solution, an initial period when no copper emerges and a lengthy period towards the end when the copper concentration and the daily increment in copper recovery are low. The simulation can be used to forecast process results before any column or similar testwork is performed. Potential applications of the simulation to process design, operating strategy and optimisation are discussed. Three modes of operation are identified that correspond to different performance patterns and dependencies on ore and process variables. The relative merits of different operating strategies for approaching the ideal performance are being investigated. For process design and development purposes, the simulation may be used with a limited testwork programme to achieve significant savings in time and resources.

Jan 1, 1989

By N J. Beukes, J Gutzmer, C Reinke, M Bau

In this study the light sparse phase search (SPL_Lt) mode on the Mineral Liberation Analyser (MLA) was successfully used to identify and quantify the abundance of rare earth element (REE) phosphates in Precambrian iron formations. Monazite (light REE phosphate) and xenotime (Y and heavy REE phosphate) are identified and data from the MLA combined with the mineral chemistry of the two minerals are used to calculate and model the expected REE concentration and distribution in these two REE phosphates. The REE phosphates account for up to 31 per cent of the REEs in the banded iron formations (BIFs) and excellent correspondence is observed between the modelled REE patterns and the whole rock geochemical data available for the same samples. Except for quantifying the mineral weights, the sparse phase search also allows for the localisation of REE phosphate grains and the observation of their association with other minerals using backscatter electron (BSE) imaging. These observations are used to conclude that the REE phosphates were most likely of diagenetic origin, with REEs and phosphate remobilised from primary chemical precipitates. It is demonstrated that automated mineralogical techniques can be used to qualitatively and quantitatively describe the influence of a rockÆs trace mineralogy on its geochemistry.

Jan 1, 2008

By Matthew I. G, Hall P. G

The Selective Precipitation (Basics) Process is a means of controlling impurities such as the ions of Mn, Mg, and Cl as well as sulphate and water, in an electrolytic zinc plant circuit. This is achieved by precipita- ting zinc selectively as a basic zinc sulphate from a portion of impure circuit solution. The impurities remain in the solution, which can be discarded, while the zinc, substantially free of impurities, is returned to the main circuit by using the precipitate as a neutral- ising reagent. A description of the process and its development to a full scale operating plant at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited is Presented.

Jan 1, 1977

A Devonian metallogenic province is extended northwards from central Queen- -sland to the Burdekin Basin in the Charters Towers Gold and Mineral Field. Devonian sediments of the Burdekin Basin are intruded by mineralised quartz felspar porphyry which occurs as pebbles in Upper Devonian conglomerate. A mineralised volcanic complex lies on the crest of an anticline in Devonian sediments.Red siltstone is slurried and reduced to pyritic hornfels over folded limestone.A thick wedge of volcanogenic conglomerate overlain by marine shale lies on the mineralised rim of an ocean which suffered cataclysmic changes during Late Devonian times.

Jan 1, 1987

By Proffett JM

Batu Hijau is a calc-alkaline, island arc porphyry copper-gold deposit located in the southwest corner of Sumbawa Island in the Banda archipelago of southern Indonesia. Proven and probable reserves are 913 million tonnes at an average grade of 0.53 per cent copper (10.631 billion pounds Cu) and 0.41 g/t gold (389 tonnes Au). Construction of the deposit infrastructure began in October 1996, and formal approval for the project mobilisation was granted by the Indonesian government in May 1997. Preoperational testing and start-up of the first grinding line is scheduled for mid-year 1999.Copper and gold mineralisation are genetically related to at least three tonalite porphyry dykes and small plugs which intrude a quartz diorite stock that was emplaced into andesitic to dacitic pyroclastic rocks and lava flows. Faults are uncommon, and where they occur they do not significantly displace hydrothermal alteration and mineralisation zones.

Jan 1, 1997

By Wiltshire PG

The process uses sodium hydroxide and sodium nitrate reagents as in conventional Harris refining plants, selectively removing the arsenic to the caustic phase at an operating temperature of 420-450¦C. A novel feature of the process concept is continuous treatment of loaded caustic slag for recovery of arsenic as a sandy crystal product suitable for further processing to arsenic trioxide. A large pilot plant was constructed and operated over a period of 3 years to develop materials handling techniques and equipment components and to prove the concept. Stable operations were achieved at equivalent capacities of 200 tonne/yr arsenic removal. The process is being considered in plans for expansion of bullion softening capacity at Port Pirie.

Jan 1, 1984

By Thompson IR

This paper describes a Client Consultant Relationship and shows how an engineering team created an environ- ment which fosters the development of good, economical and sometimes unique solutions. A major factor in establish- ing this environment was the Client's instruction to the Consultant to "propose solutions which, in the Consultant's considered opinion, best satisfy the needs of the project - not necessarily solutions which reproduce methods adopted elsewhere in the past." The Consultant's experience in other projects and disciplines outside mining has contributed by providing a cross- fertilisation of ideas. The team approach also allows the Client's expertise to be applied positively throughout the design process. These factors and the Client's foresight in providing adequate time for planning, allow the Client-Consultant Team to apply sound fundamental engineering in developing effective solutions.

Jan 1, 1975

Every step on the path from the mine to the smelter invites a comparison between material inputs on one side and outputs plus accumulation on the other. Or put simply, between what you think you have produced with what you find you have at hand. The discrepancy between these sets of comparisons is the error. Following that error in a systematic and objective manner is a way to improve the mineÆs measurement systems, that in turn leads to more accurate accounting for ores, metals and concentrates. Because the control of production is so tightly coupled with the accounting of materials, any lasting improvements in materials accounting will benefit the predictions of materials movements and quality. This translates to more reliable planning and scheduling in stockpile management, logistics, shipping and marketing. The statistical tools described are direct adaptations from the long-standing methods used to maintain the quality of manufactured product in the discrete parts industries. Their use in the process industries, of which mining is one, requires some care owing to the continuous nature of ore extraction and its variable properties. The tools can be used for problem diagnostics and as early warning systems. In common practice many professional staff, in attempting to get a perfect reconciliation between expected and observed results, try to explain away the error or bury it completely. The methodology advocated here requires a different mindset because the error must be given pre-eminence for lasting improvement to be realised.

Jan 1, 2002

By E Kozan

The paper presents new developments of the methodology of open pit coal production scheduling optimisation. They deal with the specific features of the exploitation of single coal seam and utilisation of truck-shovel and dragline systems. A production scheduling optimisation model is developed as a linear programming problem. The objective function maximises the net present value of the mining project under the technological constraints for meeting the demand function of the coal processing plant and effective utilisation of the available production equipment. Both principles of mine planning, coal quality optimisation and waste deferment are incorporated in the model. Results of a case study are provided to illustrate the applicability of the optimisation model.

Jan 1, 2003

By Duncan B

Shortwall continuous mining as first introduced at Burwood colliery, and currently being used at John Darling, Lambton, and Corrimal collieries, is a method of coal winning which was pioneered in the Newcastle district. The system uses individual hydraulic self-advancing chocks for roof support and the coal winning operation is by continuous miners and shuttle cars. Where physical conditions are suitable the system provides a safe, efficient and economically viable basis for pillar extraction. Shortwall operations have been conducted successfully in the Victoria and Dudley seam, near the coastal fringe of the Newcastle district and are now being tried out in the more difficult conditions of the Bulli seam in the Illawarra district.

Jan 1, 1972

By Lightfoot BW, Bultitude-Paull J

The Sirosmelt top submerged lancing system has many applications in the smelting of base metal and complex materials. It has particular advantages for smaller scale smelting and the treatment of recycle materials in smelters where its low capital and operating costs and its operational flexibility are of immediate benefit. The system can be fueled by oil, gas or coal, as well as by mixtures of fuels. For many applications, the use of coal as a fuel has operating cost advantages over oil and gas, but conventional pulverised coal feeding systems entail very large capital expenditure and this militates against the use of coal. The methods available for improving on conventional technology for coal firing of Sirosmelt systems are discussed and operating experience with alternative systems are outlined. The use of coal as a reductant in the Sirosmelt system is also discussed.

Jan 1, 1987