Search Documents

By W. E. Davies

"This paper is the sequel to that on Developments in Sintering Efficiency delivered by Davies and Mitchell at the International Ore Dressing Congress, Stockholm, 1957. Attention is drawn to the fundamental concept of sintering as a heat transfer process, in which the ignition heat is continually transferred onward through the bed as a heat wave. By its passage, this heat initiates endothermic 'changes, such as carbonate decomposition, whose energy requirements are supplied by the combustion of the fuel contained in the bed.Ideally, the heat wave should be generated by the ignition hood followed by the pre-heating of the incoming air. The fuel content of the bed should be no more than the theoretical quantity needed to balance the endothermic changes. In practice, the heat wave is seriously short of energy and this is offset by excess fuel in the bed. As a result, sinter quality suffers, more return .fines are produced, and fuel is wasted, a loss of efficiency which could be avoided if the fundamentals of correct ignition were more widely appreciated.Sintering speed, otherwise heat wave velocity, is a function of the rate at which the incoming air acquires .heat from the cooling sinter and imparts it to the unburned feed below the combustion zone. It is thus a function of rate of air flow and so depends on bed permeability>. Ways of• improving and maintaining permeability at the maximum consistent with thorough sintering are discussed, particular reference being made to taconite concentrates. The possibilities of recrystallizing refractory ores into forms more amenable to physical concentration techniques by sintering are visualised, very little expenditure on heat energy being required when the process is operated near the ideal conditions."

Jan 1, 1960

By Peter A. Eshun

This paper studies two methods that account for risks associated with gold mining projects such as mineral risks and country risks. The first method is sensitivity analysis, which investigates the effects of a change in any economic parameter such as operating cost, capital investment, gold price or taxes on the viability of the project. The second method is Monte Carlo Simulation technique, which takes into consideration the simultaneous random variation of the economic parameters on the project's viability. An automated simulation cash flow model has been developed as part of this paper. Sensitivity analysis and the simulation model have been used to investigate the economic viability of the Dokrupe Gold Project (DGP) serving as a test case. It is concluded that, the Monte Carlo Simulation technique gives a more realistic judgement of the economic viability of gold mining projects.

May 1, 2004

By A Walker

The presence of high noise levels in many industries, together with the fact that countries are becoming increasingly concerned with the health of its citizens, has contributed to the importance of the problem of hearing loss. This problem has become the focus of scientific research, law and medicine, and the object of this thesis is to present the means whereby noise may be detected, with its resulting effects and possible means of control, in mining operations. 0BJECTIONABLE noise is a particularly prevalent by-product of the mining industry, and, al-though a dangerous noise level has been recognized, it is believed that at no time now, or in the future, will it be possible to enumerate a single over-all decibel figure at which hearing impairment will oc-cur. Individual susceptibility must be recognized in any study of occupational loss of hearing aimed at the setting of standards and criteria for industrial noise control.

Jan 1, 1963

By P. Massi

"Wholly owned by the Coniagas Mining Company, the oldest continuously listed mining company on the Toronto Stock Exchange, St. Andrew Goldfields is located on Hwy. 101 approximately 30 miles east of downtown Timmins, Ontario. Geographically situated on the Porcupine-Destor Fault, the mine and mill in Stock township is positioned in the heart of Northeastern Ontario's goldmining communities.In July 1988, a 600 ft. shaft, hoist, and compressors were already in place when construction started on a 500 T.P.D. capacity C.I.P. mill and crushing plant.By June 15, 1989 the mill was commissioned and attained the design capacity by August of that same year. Since then, changes to the circuit have increased throughput to 900 T.P.D. from two significantly different ore sources.Meeting the Ministry of the Environment's guidelines is an ongoing commitment utilizing the Inca S02 process in line between the tailings pond and secondary polishing pond.INTRODUCTIONExploration on what is now known as St Andrew Goldfields' Stock Township Mine was carried out ln the early l960 1 s by Hollinger Mines Ltd. The property was acquired by Quebec Sturgeon River Mines 1n 1973 and the main shaft was started ill 1979.When St Andrew Goldfields was incorporated 1n 1983, exploration and development commenced to identify the ore body. The company decided 1n 1987 to bring the Stock township property into production after an extensive feasibility study and testwork at Lakefield Research in Toronto. Leslie Engineering was contracted to design, engineer and procure al 1. equipment from the coarse ore bin to the tailings distribution system and backfill plant"

Jan 1, 1992

By J. J. Crowder, A. L. Coulson

Ground support is a significant component of underground mining costs. The rehabilitation of failed support, however, is often much more expensive than the initial installation. This paper investigates whether the right type and length of support can be designed correctly the first time, through forward modelling of the support and the mining process. Back analyses demonstrate how high-quality instrumentation and monitoring can help with the estimation of the post-peak (post-failure) rock mass parameters required for a comprehensive analysis. A hybrid modelling approach combines a three-dimensional mine-wide boundary element model with a non-linear finite element model to allow for the failure process in the rock mass. The back analyses demonstrate that, for the case study site, the post-peak Generalized Hoek-Brown value of mr must be reduced significantly in order to properly simulate displacements observed in instrumentation data. High-quality instrumentation data is the key to post-peak rock mass parameter calibration. The procedures outlined in the paper highlight the need for a new hybrid numerical modelling package that can use the influence of three-dimensional mining-induced stresses to predict displacements in, and potential failure of, rock masses surrounding mining infrastructure in order to radically alter strategic and tactical mine design.

Jan 1, 2007

By Fred V. Seibert

The Functions and the Responsibilities of the Institute The Canadian Institute of Mining and Metallurgy is unique. ln addition to the welfare of its members, it has a real interest in the welfare and promotion of one of Canada's largest and most important basic industries. It is because of this that the membership is composed of both individual and corporate members. The individual members are both technical and non-technical (Members and Associates). Both Members and Associates have the same status in the Institute and all are interested in the welfare of the mineral industry. The aims and objects of the Institute 11re twofold. The education and welfare of its individual members and the sound promotion and welfare of the mineral industry. Perhaps it might be well if we reviewed these aims and objects as stated in our Constitution: "First - To promote the arts and sciences connected with the economical production of valuable minerals and metals, by means of meetings for the reading and discu11ion of technical papers, and the subsequent distribution of such information as may be gained throo.gh the medium of publications". It cannot be denied that we have do ne a good job in this particular phase of our work. Nevertheless, there is still room for improvement. It has been suggested that we might have more discussion and, on occasions, more criticism of our papers and programmes. This can best be done if the authors will have their papers prepared in sufficient time to permit of preprints being made availa1ble before the meeting at which they are to be presented.

Jan 1, 1950

By G. Bridgstock, S. S. Forbes, E. M. Elkin

"OPERATIONS at Canadian Cop-per Refiners Limited, since the refinery was established in 1931, have been described in previous papers ( 1,2). Since then the refinery has treated the entire copper output of Noranda Mines Limited and Hudson Bay Mining & Smelting Company Limited. With the commencement of production in 1956 at Gaspe Copper Mines Limited, this copper has also been refined. From the start of operations to the end of 1958, the following had been refined: copper, silver, gold, selenium and tellurium.Construction of new buildings and additions to other buildings have been needed to handle increased receipts. The refining capacity has been increased from 112,000 tons of copper per year to a total of 236,000 tons per year.The refinery is located at Mont-real East, Quebec, close to railway and highway facilities. Incoming materials and shipments, with some small exceptions, are handled by rail. Some finished products are sl1ipped by industrial flatcar to the adjoining plants of Canada Wire & Cable Company Limited and Noranda Copper & Brass Limited."

Jan 1, 1960

Burr Mineral Resource has: ?Grade / Thickness / Tonnage ?Dry Caprock ?Low Carnallite ?Low Clay / Insolubles ?Flat & Continuous Deposit ?Proper depth

May 1, 2009

By F. E. Patton

"IntroductionAT NORANDA, the strength of the ore and wall-rocks per-mitted mining in large open stopes. While some of the orebodies were small and could be mined out in one stope, in most cases their size was such that it was essential that ore pillars be left during the first stage of mining. In these cases, backfilling has been necessary for ground control and to facilitate the later recovery of the ore in these pillars.This paper discusses the development of the •backfill and •its use in pillar recovery.GeologyThe ore bodies at Noranda occur as replacement deposits in a block of rhyolite flows and breccias, bounded on the north by the Horne Creek fault and on the south by the Noranda Andesite fault. Mineralization consists of pyrite, pyrrhotite, magnetite, chalcopyrite, sphalerite, gold, and various tellurides.The main orebody is a massive sulphide deposit designated the 'H' orebody. It is elliptical in plan, measuring roughly 400 feet by 800 feet, and is divided into two zones -Upper H, extending from surface to the 1,500-foot level, and Lower H, from the 1 ,500-foot level to just below the 3,000-foot level.Mining MethodsOpen stope mining in both Upper H and Lower H zones has been fully described in previous publications (1). A brief review only of the mining methods will be given here."

Jan 1, 1952

By N. Melnyk, H W. Habgood

The conventional low temperature process for extracting' helium from natural gas involves liquefying the whole gas stream in order to remove the relatively small fraction of helium. A process based on the selective diffusion of helium through a semi-permeable barrier is, in principle, more economical and flexible, particularly for the treatment of small re-serves and low concentrations. The well-known permeability of glass to helium offers the possibility of such a diffusion process and McAfee of the Bell telephone Laboratories showed in 1958 that practical separations could be achieved by passing natural gas over bundles of fine capillary glass tubing. Developmental studies have been carried out involving larger units and more extended field tests than those of McAfee. Fine capillary tubing of Pyrex glass 0.0035 in. diameter was prepared by drawing ordinary 6 mm. laboratory tubing in a furnace. Extraction units were pre-pared containing about 10,000 such tubes, 4 ft. long and cemented inside

Jan 1, 1961

By Robin Sheremeta

Fording Greenhills first acquired GPS (Global Positioning System) technology with the commissioning of a GPS-based dispatch system in December 1994. The second exposure to satellite technology came with the conversion of the conventional optical survey system to a high-resolution GPS system in June 1995. In September 1995,a GPS-based grade control system was tested on the largest shovel (Marion 301 — 58 cubic yard).In January 1996, the system was added to all of the cable shovels (2 P&H 2800s). All three applications of GPS at Greenhills are fully operational and producing positive results. This paper will focus on the practical application of GPS in a mining environment and the effect that GPS technology has had on the Greenhills Mine.

Jan 1, 1996

By Luis A. Tondo

The Paracatu Expansion Project III in Brazil was implemented between 2006 and 2008 to increase the existing capacity from 20 to 61 Million tons per year of gold ore treatment. This expansion led the Brazilian subsidiary of the Canadian Kinross Gold Corporation to become the single largest gold producer in Brazil and the largest single gold concentrator in the world, with a nominal capacity to treat around 167,000 tons per day of ore. This paper describes the Project Development areas for the Paracatu Expansion, using the approach proposed by the Project Management Institute (PMI) and the methodology included in the PMBOK (Project Management Book of Knowledge). The author has more than 20 years of experience in the gold mining industry, having worked as a plant metallurgist, mill superintendent and development manager for RPM until he took the position as the Project Manager of the Paracatu Expansion III in 2005. Luis Tondo has a BSc in Mining Engineering from UFRGS-Brazil, an MScEng from the University of Queensland - Australia and an MBA degree from FDC-Brazil. Luis is currently based in Santiago-Chile, acting as the Project Director for developing projects in Latin America for the Kinross Gold Corporation.

May 1, 2009

By Roe-Hoan Yoon

"Industrial flotation columns often suffer from low recoveries and high maintenance requirements because of poorly-designed air spargers. The MicrocelTM bubble generators were developed at Virginia Tech to overcome these problems. In this system, small air bubbles are generated by circulating a portion of the flotation pulp through a set of static in-line mixers. The small bubbles improve flotation kinetics and allow a higher recovery (or capacity) to be achieved. Other advantages of the system include reduced air consumption, plug-free operation and on-line maintenance. This article discusses the advantages of the MicrocelTM bubble generators and presents examples of successful in-plant demonstrations.IntroductionColumn cells are widely accepted in industry for cleaner operations because they are more selective than mechanically-agitated conventional cells. The improved selectivity can be attributed to the use of wash water which minimizes the entrainment of fine gangue particles into the froth product. Columns may also produce higher recoveries if the air sparging system is properly designed and steps are taken to minimize back-mixing. Furthermore, the quiescent conditions afforded by column cells may be beneficial for recovering coarse particles that are readily detached from bubbles under more turbulent conditions. Also, properly-designed columns offer advantages in terms of savings in floor space, reduced operating and capital costs, and simplified circuitry.It is unfortunate, however, that some of the advantages of columns are not fully realized in industrial practice. Some column circuits are unable to achieve their design capacity, while others require extensive maintenance programs. These shortcomings can usually be attributed to deficiencies associated with the design, scale-up and operation of the air-sparging system. In this article, some of the basic problems associated with commercial air sparging systems are discussed and alternatives are suggested."

Jan 1, 1994

By J. A. Russell

IT IS the purpose of this paper to show how the design of the larger slope hoists in use in the mines of the Dominion Steel and Coal Corporation has tended to evolve ta suit the particular conditions of operation. These hoists are all used for hauling coal in trains or trips of pit tubs up the mine slopes, which usually follow the dip of the seam . As the mine is developed to the dip and the slope grows in length, the length of the rope and the size of the hoist required to handle it rends to become extremely cumbersome. It has been found that the best economic conditions of hoisting are obtained when the length of the slope is limited to about seven or eight thousand feet. Beyond this length it is necessary to offset to one side of the line of slope and start a second or auxiliary slope, which will be served by its own hoist installed underground. With this hoisting distance as a basis, we find that we can economically hoist the outputs required, usually about 1,500 tans per eight hours per slope, by hoisting the coal in trips of about twenty boxes. This, on the grades obtaining, will require a rope of about l 1/4in. diameter, running at a speed of 1,200 ta 1,800 feet per minute, and requiring from 1,200 to 1,800 h.p. at the hoist shaft. The tendency is for the rope speeds of the surface hoists to be a little higher than the underground hoists which relay to them, so that the surface hoist has a small margin of time in hand. The oldest surface hoists were steam-driven, but, with few exceptions, these have given place to electric hoists. With the exception of one hoist, which was altered in design, the steam hoists have not had the opportunity of evolving in the same way as the electric hoists, and will not be mentioned any further.

Jan 1, 1944

By Rejean Gagnon, Fernand Rochefort

"Haulage costs, in most operations, represent a large portion of total cost. Quebec Cartier Mining Company came to the conclusion t hat an electric trolley assist providing more horsepower than available from dieselgenerator sets presented the best oppor tunity for improvement. Accordingly, a testing and development program was carried out which resulted in the design, installat ion and application of a practical system. This paper describes the development of the system, the equipment used as well as the actual operation. A projection is also made to indicate further improvement in productivity. A comparison is made of truck operating data before and after activation of the trolley assist system in order to determine its economic impact."

Jan 1, 1972

By Ernie Doell, Trung Nguyen

"In early 1995 Cluff Mining commissioned a newly constructed high density tailings thickener at its Cluff Lake uranium mill. The 85 ft diameter high density thickener is one of the first of its kind in North America, and incorporates the novel paste technology in its design to produce densified (in the range of 60 -65% solids) mill tailings suitable for stable deposition in the tailings management area. This paper discusses the impetus behind the installation of such an unconventional thickener, and the many trying experiences in making it operational.IntroductionCluff Mining, a wholly owned subsidiary of Cogema Resources Inc., is the operator of a uranium mine and mill complex at Cluff Lake which is located in northern Saskatchewan. Since 1980, the company has developed and mined out several different ore bodies within the Cluff Lake region for the production of uranium concentrates, commonly known as yellow cake. Based on the known ore reserves, the Cluff Lake operations are projected to last till the early 2000's.Tailings from the Cluff Lake mill have been discharged to a tailings management area consisting of a tailings pond and two facilities for primary and secondary treatment systems. The tailings pond has an impervious bentonite lined dam, and it is divided into a solids and a liquids holding areas. Until the beginning of 1995, the mill tailings were discharged in two separate lines to the solids pond; one line carried the slurry residue of 45-50% solids (w/w) from the CCD circuit, and the other discharged raffinate tails containing less than 1 % (w/w) gypsum precipitate. Supernatant in the solids pond is treated in the primary treatment system prior to discharging to the liquids pond. Figure 1 shows the site plan of Cluff Lake tailings management area.It has been estimated that by the end of 1995 the solids pond would be filled to about 60% of its design capacity, and probably would be full before the year 2000. Therefore, Cluff Mining had to consider a more efficient tailings disposal method that could extend the service life of the existing Cluff Lake tailings management area. A high density tailings thickener was believed to be the most practical and economical system for tailings disposal at Cluff Lake mine."

Jan 1, 1996

By G. A. Kosick, G. S. Dobby, O. Matwijenko

"A 100 kg/hr portable flotation pilot plant has been operated at Kidd Creek Mines with the objectives of:(a) determining performance expected by column flotation circuits on primary zinc and copper cleaning, and (b) evaluating column flotation circuit configurations.The self-supporting pilot plant, owned by Minnovex Technologies Inc. and operated by Minnovex and the University of Toronto, consisted of three 16 cm diameter by 6.5 m high columns and a bank of four Denver No. 7 cells. It was configurable to any arrangement using these four (or fewer) units. The columns were controlled through the use of multiple pressure transducer measurements. This paper presents the approach to testing and the results of more than 70 circuit tests. INTRODUCTIONThe integration and retrofitting of flotation columns within existing mechanical cell flotation circuits is becoming a common occurrence. The correct approach to this integration, however, is often difficult to define, due to a scarcity of previous experience and the difficulty in predicting column circuit performance. In most cases, the effect of column implementation has been experimentally assessed using a single pilot column, with the consequence that selection of an appropriate circuit to implement is difficult. Important considerations are the impact that column water addition will have on the existing operations, and the differences between mechanical cell and column performance in integrated cleaning circuits.To address the problem of circuit selection a portable flotation pilot plant, consisting of both columns and mechanical cells, was designed and constructed by Minnovex Technologies. The pilot plant was structured for complete flexibility of circuit configuration, with the intent to provide a means by which both research and plant personnel could determine the best possible column circuit configuration for a given application."

Jan 1, 1990

By L. Drisdelle, S. Gendron

"Survival in today's business climate requires participation of all employees in a Total Quality Management Program encompassing everything - ""safety, quality of products, quality ofet1ch and every job done, and of course production "". We all know what needs to be accomplished, but struggle with how to do it, especially in an industry which has not always experienced management/union cooperation, and mistrust is still present.This paper describes a process to improve team work and employee involvement in Inco's nickel carbonyl refinery at Copper Cliff The process involves facilitatorship training for all employees, and a system for reinforcing and accomplishing the required behavioural change. The system is described in detail and a number of examples are presented. At the refinery, the staff is starting to understand as Max DePree recently wrote ""Without Quality Behaviour, you cannot have Quality Product"". IntroductionThe Copper Cliff Nickel Refinery (CCNR) is Inco's largest and most modern nickel refinery, which celebrated its twentieth year of successful operation in April 1993.The heart of the refinery is the Inco pressure carbonyl (IPq plant which produces high purity nickel pellets and specialty powders by refining an approximate 80% nickel granule feed. The carbonyl plant is a modem chemical plant with very special and demanding requirements for safety and environmental protection due to the toxic nature of the refining gas.Since 1987, there has been an emphasis at CCNR on a comprehensive Total Quality Improvement (TQI) Program which was designed based on recognizing customers' needs for improved systems for quality management. This program is customer oriented and comprises such elements as team organizational concepts, customer audits, process assessment and internal quality auditing.A detailed review of progress was made in early 1991 and it became apparent that the ""ownership"" of the TQI program was not broad based. In fact, the program was very much a staff driven effort and fell far short of total employee involvement and relentless continuous improvement that are now considered essential to remain competitive and stay in business.Inco staff has now come to regard that early phase of our TQI program as ""the technical aspects of total quality improvement"".The safety experience was also puzzling. Even though the safety statistics were good with an average lost time frequency of 1.6 for the last five years, the perfonnance improvement had plateaued and remained pretty much the same. Clearly a new approach was required if significant progress and continuous improvement was to be made."

Jan 1, 1994

By John L. Bonus

"WITHIN THE BROAD PARAMETERS implied by the title of my speech, I propose to deal more particularly this evening with a subject the many aspects of which have constituted the essential elements of one of the main thrusts undertaken by the MAC in the past two years, i.e., to create among Canadians a much greater awareness of the importance of mining and to demonstrate to them what are the many and varied benefits they derive from mining activities across their country. In other words, MINING - WHAT IT MEANS TO CANADA.I also intend to discuss some aspects of government-industry relationships.I am very conscious of the fact that I am speaking to an audience made u in large part of experts in several fields of mining and exploration activities. They will be familiar with many of the points I intend to discuss. However, without in any way suggesting that familiarity breeds contempt, might I emphasize that even in this particular forum there is justification for reiterating some of our basic philosophies and suggesting ways whereby they might be better understood and promoted.Let us first summarize the present dimensions of the Canadian mining industry."

Jan 1, 1971

By Kevin Bell

About Beltek Inc. For more than a decade Beltek, Inc. has been working with national and international organizations to harness and deliver solutions which gain real ebusiness advantages in today's world. Our objectives are to partner with our customers to achieve maximum results, while reducing costs. At Beltek, we provide a commitment to you and your organization's needs. Whether that be delivered by ensuring our services and products are state of the art or by providing a level of personalized service, which makes you feel like the center of attention, Beltek is about adding value to every job we work on. The individuals who work at Beltek quickly become your friends because we share your passion and enthusiasm for the business we are in. That's why every person is a leader in his or her respective fields. Having these individuals as apart of our business ensures you get the best out of our equipment, receive the very latest in advise, problem solving and support. We also pride ourselves on our ability to remain flexible at all times because we know deadlines and schedules can change quickly, so we always go the extra mile to deliver exactly what you need.

May 1, 2004