Search Documents

By T. Guan, G. Fu, X. Zhou, L. Deng

"Currently, tailings water is required to be recycled in minerals processing plants. When the flotation tailings water of complex copper-sulfur-tungsten polymetallic ore is reused to the flotation of copper-sulfur ore, a portion of tungsten would be lost in copper concentrate or sulfur concentrate due to the addition of the collectors used for oxidized ore which are also effective for the sulfide minerals in the process of tungsten flotation. At the same time, the technical index of copper concentrate and sulfur concentrate would be seriously affected by tailings water. Our experimental researches of many years show that the copper concentrate with a grade of 18.36% Cu at a recovery of 76.67% is obtained for the raw ore containing 0.60% Cu, 18.99% S, 0.16% WO3 in small locked cycle test using recycled water, through simple pretreatment of the tailings water from tungsten flotation and adding special regulator CW and new tungsten collector TM. The result is close to the performance without using tailings water. And, in the continuous pilot experiment which was continuously conducted for 4 days with the same technology, the following results was obtained: the copper concentrate with a grade of 21.74% Cu, the recovery was 71.55%; the sulfur concentrate with a grade of 45.16% S, the recovery was 80.10%; the tungsten concentrate with a grade of 42.63% WO3, the recovery was 54.62% relative to raw ore (the recovery relative to scheelite was 76.47%). The throughput of the continuous pilot experiment is 1.0~1.2 t/d, and the raw ore contains 0.56% Cu, 18.80% S, 0.14% WO3 on average.INTRODUCTIONMining industry is one of the most important developing fields, it supplies raw materials for industrial production as well as discharges much waste water. Tailings water is the main source of beneficiation waste water, it would result in severe environmental pollution if discharged directly. Generally, the tailings water would bring undesirable effect on flotation index after simple pretreatment by lime (Kalin, Fyson, & Wheeler, 2006). On the other hand, the treatment of tailings water through ion-exchange (Cui & Liu, 2015) before recycling is of high cost. Generally, in the flotation of Cu-S-W polymetallic ore, when the tailings water from tungsten flotation is treated simply by lime and recycled to the flotation of sulfide minerals, the flotation index of sulfide minerals decreases, and a portion of oxide mineral would be lost in the sulfide concentrate. As a result, the recycle rate of this kind of tailings water is relatively low, some of the tailings water is discharged after simple treatment and then environmental pollution is caused subsequently. One of the effective ways to improve beneficiation performance and increase the recycle rate of tailings water is to conduct research on developing recycle technology for flotation tailings water of complex copper-sulfur-tungsten polymetallic ore."

Jan 1, 2016

By Bahaa Hussein

Considerable number of methods and procedures has been introduced for trending and progress reporting of engineering, procurement and construction projects. This paper introduces a novel method, designed to augment the set of indices for measuring schedule performance. The concept behind the developed method is to provide early warning by dynamically evaluating the schedule cumulative impact of construction projects. The proposed method is designed to highlight the gradual deterioration in schedule status resulting in a cumulative impact due to the aggregation of small delays encountered during the execution of non-critical activities, and can be used as an add-on utility to existing software systems that perform CPM scheduling. The proposed method is based on a developed formulation for quantification of the Schedule Compression Index, which takes into consideration the remaining project activities durations. The index is developed based on periodic comparisons of ?Current Schedules? and the project ?Baseline Schedule? using the summation of the remaining activities durations. A numerical example is presented to demonstrate the application and capabilities of the developed method. It is expected that the developed index together with other schedule performance indices would be of value to decision makers and members of project teams.

Aug 1, 2013

By L. Juteau

"""The north coast of the St. Lawrence River will be the scene of an industrial development during the coming decades"". The facts which underlie this statement are the occurrences of iron and titanium ore, the abundance of hydro-power and the availability of deep-water ports in this region. Havre St-Pierre, Sept-Iles, Port Cartier and Baie Corneau already exist as major ports and urban centers. The huge quartz deposit at Baie Comeau will be a decisive contributing factor in the development of a metallurgical plant in this area. Due to its purity, it lends itself, first of all, to the manufacture of glass of different kinds, being comparable to the quartz sands now used by the plate glass and glass container industries in the Montreal area, Moncton, N.B., Trois-Rivieres and - in the future - at Bécancour, Quebec. However, its high quality will also make it possible to use it as one of the main basic materials for the production of silicon carbide and ferrosilicon, and as a flux in metallurgical processes. It is intended, in this report, to offer conclusive proof of the economical importance of this large quartz deposit by presenting the results of the studies made to date."

Jan 1, 1971

By Tyler J. Irving

"In June, 2018 Lalor Mine experienced a catastrophic blade failure of its No. 2 main exhaust fan. Over the following weeks several key changes were made to the auxiliary ventilation system to allow for continued production while the exhaust fans were repaired. Issues encountered during the period of reduced ventilation, and how they were addressed, are analyzed. The suspected causes of the exhaust fan blade failure and how risk was mitigated during the reconstruction are discussed. Key findings and lessons learned are summarized.INTRODUCTIONLalor Mine, owned and operated by Hudbay is an underground zinc, gold, and copper mine located in northern Manitoba. The mine workings extend to a depth of 1090 metres below surface and is ventilated using a push-pull system. The mine exhausts through the main exhaust raise; equipped with two, 2,500 HP fans and upcasts through a portal located at the neighboring mine, Chisel North. Air is supplied to Lalor Mine through four intake fans: The Production Shaft Downcast (two, 250 HP), Lalor Downcast (one, 400 HP), and Chisel Downcast (one, 600 HP) fans (Figure 1). In June 2018, Lalor was scheduled to produce approximately 4,000 tpd.On June 20, 2018 at 2:52 pm Lalor Mine experienced a fault on the Variable Frequency Drive (VFD) for Exhaust Fan No. 1. Time would be needed to complete the necessary repairs. The No. 2 exhaust fan was ramped up from 525 rpm to 800 rpm, 90% of its capacity, in order to maintain underground ventilation. At 4:46 pm, approximately two hours after the rpm was increased, exhaust fan No. 2 experienced a catastrophic blade failure. The forces from the blade failure resulted in the top half of the fan housing being thrown 50 metres from where it was installed; with several large sections of fan blade being thrown further (Figure 2)."

Jan 1, 2019

By N. Aslin, R. Clark, G. Heferen

The methods of harvesting copper from stainless steel mother plates has been investigated from fundamental and operational experience perspectives. At least five different harvesting techniques have been identified that have different effects on product quality, current efficiency, current distribution, growth morphology and ease of stripping. Each method is examined from fundamental principles to understand what occurs during the harvesting process and why the particular effects are manifested. Experience from plants operating the harvesting method is provided to show that the fundamental understanding is relevant. Best practice harvesting method and harvesting management are described.

Jan 1, 2014

By O. A. Carson

"IntroductionTHE ZINC-BASE die casting alloys in common usage contain approximately 4 per cent aluminum as the major alloy element. In addition, they contain about 0.05 per cent Mg .and may• have a small amount .of copper. These are usually the only •elements intentionally present.Small amounts of some impurities have been shown to have a deleterious effect on the properties of these alloys and therefore the impurities are kept low by starting with '99.99%' zinc.The reasons for holding the aluminum content at 4 per cent are not clear. Some statements appear in the literature that higher aluminum increases the brittleness, but probably the chief reason was the relative price of zinc and of aluminum when 4% alloys became firmly established. At that time, aluminum was three to four times the price •of zinc on a weight •basis. Recent prices, roughly equivalent per lb., make aluminum considerably cheaper than zinc on a volume basis and suggest that increased aluminum content would result in a decrease in the cost per piece due to the lower density of the alloy.Little information could be found in the literature and, therefore, it was decided to determine some physical properties of the higher aluminum zinc-base alloys made from high-purity zinc."

Jan 1, 1953

By W. A. Green

Introduction While pilot-mill operations were being carried on at Flin Flon, as described by R. E. Phelan (1), a detailed topographic map was being made of the area in the vicinity of the ore-body for later use in laying out plans for the final plant. The area covered by this survey was 6,600 feet by 6,600 feet, with contours on 2-foot intervals. As mentioned by Mr. Phelan, it was definitely decided at the end of November, 1927, to take up the option on the Flin Flon property and to proceed immediately with the plans for construction of a metallurgical plant at Flin Flon to treat 3,000 tons of ore per day, and of a hydro-electric power plant at Island Falls, Saskatchewan, to supply power for the future operations at Flin Flon. Railway Built From The Pas to Flin Flon Just as soon as the decision was made to go ahead with the construction work and opening-up of the property, it was of course essential to give immediate attention to the building of a railway to the mine. Many years previously, a preliminary survey had been made for a railway to branch off the Hudson Bay railway at a point 4.7 miles northeast of The Pas, and, during certain negotiations in 1925, the Provincial Government of Manitoba had agreed to guarantee the railway bonds necessary to finance the building of the line, so that it was possible to organize for this work immediately. A contract was let by the newly organized Manitoba Northern Railway Company to the Dominion Construction Company, Ltd., and Tomlinson, for the building of the railway to the mine, a distance of approximately 87 miles (see Figure 1). The Manitoba Northern railway is a subsidiary to the Canadian National railway, and all engineering and supervision of the contractors was done by the Canadian National engineers. Actual construction work was started in January, 1928. The first 52 miles of the railway from The Pas to Cranberry Portage is over fairly level, although slightly rolling, country, and a considerable portion of the route is over muskeg area. Rails were laid on top of the frozen muskegs. Gravel deposits were opened-up along the line and, before warm weather; sufficient ballast .was distributed in the muskeg areas to prevent thawing under the track, and thus give the necessary support to allow uninterrupted transportation over the line.

Jan 1, 1935

By Peter N. Calder

The orientation of planes of inherent weakness (joints) with reference to an excavation in rock is the critical factor determining stability. The purely frictional 'residual' strength remaining following the breakdown of initial cohesion is the only strength which can be counted on to resist sliding for the long term. A simple method of resolving driving and resisting forces in three dimensions along joint intersections 'undercut' by the excavation is presented. Contrary to the case of slope failure in soils, it is shown how significant changes in the slope angle sometimes have no effect on the degree of stability pre-sent in rock slopes. Wall control by reorientation of the slope, the use of cable bolts and water diversion are briefly discussed.

Jan 1, 1970

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983

By B. N. Nandi

This paper is a study of the application of the science of coal petrology to the use of coal in the iron and steel industry. The petrography of coal is given the most attention, with some mention of coal palynology. The history of the petrographical analysis of coal is first out-lined, with a description of the various coal entities, and then the apparatus and experimental techniques employed for coal evaluation are discussed. The coke stability factor and the relation of coke strength to petrographical data are also covered, and some space is given to the new science of coke microscopy, in particular its use in following the oxidation of coals.

Jan 1, 1966

By E. Landry, W. Naudts

"The amenability theory was developed by Alex Naudts and considers grouting operations as continuous permeability tests where Newtonian test fluid water, is replaced by a cementitious or solution grout. It utilizes hydraulic conductivity and grouting data to establish the amenability coefficient of a particular grout zone. The amenability coefficient reflects the quantity of apertures or voids accessible to the selected grout, divided by the number of apertures accessible to water, in the zone intersected by the grout hole. By calculating, in real time, the effectiveness of a particular grout at the start of a grouting operation, the most appropriate grout to match design criteria can be targeted. By incorporating the amenability theory in every grouting operation, schedule savings and an increase in productivity are typically achieved. Three short case studies illustrate different enhancements in productivity: At an underground mine during the construction of declines, a cement based suspension grouting program was highly ineffective and did not appear to affect the inflow into the mine workings. The amenability theory was utilized to evaluate the grouting program and based on this evaluation, changes to the grouting program were made which allowed the grouting to meet the project’s objectives. On another project, a pre-excavation grouting program implemented during shaft sinking operations utilized the amenability theory to select the most suitable grout for the program. Schedule constraints also influenced the selection of the grout. In the third case history presented, the amenability theory was used to select the grouting sequence of every individual grout hole for a grouting project in a highly heterogeneous soil formation. INTRODUCTION The amenability of a given soil, civil structure or rock formation for a particular grout formulation is a measure of the ability of that grout to permeate the pores, fissures and apertures water will flow through. The amenability coefficient of a particular grout for a specific zone equals the percentage of apertures, pores and fissures accessible by water that are also accessible by grout. Grouting should be viewed as a continuous permeability test, where the apparent in-situ hydraulic conductivity value for a particular grout zone is continuously evaluated, using grout instead of water as test fluid."

Jan 1, 2019

By S. A. Scott

In 1913, potash mineralization was recognized at a depth of over 7,000 feet in an oil-well hole (Norcanol's Radville No. 1 well) drilled near the town of Raddlle, Saskatchewan. Although, at this depth, potash is not considered mineable by conventional underground mining methods, this discovery shed the first light on the potash deposits of Saskatchewan in much the same manner as oil-well drilling was responsible for the first discovery of potash in the Carlsbad Basin of New Mexico in 19:25. The discovery near Radville alerted the oil-well geologists and, as a result potash mineralization was recognized in the Verbata No. 2 well, near Unity, Saskatchewan, in 1946. The mineralization, which was at a depth ?of 3,466 feet, graded more than 20 per cent K20 over a thickness of eleven feet. This discovery, as its depth, thickness and grade were all amenable to mining,

Jan 1, 1963

By R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. This paper presents the findings of on-going testing of various sizes and shapes of grinding media. Plant observations combined with estimated breakage rates demonstrate the importance of appropriate selection of media sizes on the milling operation.IntroductionBrunswick Mining and Smelting is located near Bathurst, New Brunswick, and operates one of the world's largest lead and zinc mines. The ore mineralogy and processing flowsheet have been described elsewhere (Petruk and Schnarr, 1981; Shannon et 01., 1993). Despite the 25 years' milling experience, there has been considerable disagreement as to the required grind size (Grant et 01., 1991). Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37 um) and averaged slightly above 71% in 1992. Results from mineralogical analysis (Petruk and Schnarr, 1981), laboratory and pilot plant experiments, as well as plant sampling (Grant et al., 1991; Hendriks and Ounpuu, 1985; Shannon et al., 1993) indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15 urn to 25 um range.This paper shows the results obtained so far from the evaluation of the effect of grinding media size and shape on grinding mill efficiency. The problem of finding optimum grinding media size, shape and composition has been recogrtized since the early 19405. The main criterion for the selection of media size is the size of the material to be ground (Bond, 1958). Although several relationships have been proposed to assist in the selection of grinding media size, none of them are entirely satisfactory (Wills, 1988). Other approaches using the breakage rates and process simulators were developed to help in the selection of grinding media size (Austin et al., 1976; Lo and Herbst, 1986; Concha et 01., 1992; Samskog et al., 1990; Martinovic et al., 1990). Although considerable effort was put into the analysis of grinding media size, very little information is available on the effect of grinding media shape (Norman and Decker, 1985, p. 3C-4). Norris (1952), Kelsall et al. (1973) and Herbst and Lo (1989) have shown that balls are more efficient than other shapes of grinding media including truncated cones and cubes."

Jan 1, 1994

By L. M. Pidgeon

Introduction The production of magnesium by direct reduction of the oxide has far passed the experimental stage and was responsible for 30 per cent of the recent wartime production of 246,000 tons per annum. This paper describes the small-scale experiments which culminated in a number of the wartime plants. The paper traces the author's early experiments on various direct reduction reactions leading to his choice of the ferrosilicon reduction of dolomite and the realization that this reaction would proceed at a satisfactory rate at temperatures obtainable in metal apparatus. MgO has a standard heat of formation of 146,100 cal. and is therefore one of the most difficult oxides to reduce. However, if advantage is taken of the relative volatility of magnesium metal, thermally unfavourable reactions may be utilized. In reaction MgO + X = XO+ Mg . . . . . . . . . . . . . (1) the removal of Mg as a gas at high temperatures displaces the equilibrium to the right in the face of the unfavourable thermo-chemistry which is inevitable with any X other than calcium metal. If X is carbon, not only is the reaction highly endothermic, but CO is gaseous. A temperature of l,864°C. is required to produce a pressure of one atmosphere of Mg. Between l,900°C. and perhaps 400°C., the back reaction takes place readily and special shock cooling devices are required to recover magnesium from the gaseous mixture. This reaction does not lend itself to small-scale experiments and was not examined by the author. If, in reaction, carbon is replaced by a relatively pan-volatile metal, the oxide of which is also non-volatile and possesses a fairly high heat of formation, a reduction reaction is offered which is free from the difficulties associated with carbon. The typical case of silicon will serve as an example: 2MgO + Si = SiO2 + 2Mg (g) . . . . . . . . . . . . . . . . . . . . . . (2) At temperatures above l,000°C., a positive pressure of magnesium will exist over the system. Removal of the magnesium vapour will displace the reaction to the right in the face .of an unfavourable thermal balance. Since magnesium is the only volatile component at this temperature, it may be evolved and condensed, using attractively simple distillation technique.

Jan 1, 1946

By B. A. Strathdee

An arsenical ore containing both pyrite and arsenopyrite was heated to a temperature at which decomposition and distillation took place. The condensate consisted of metallic arsenic and arsenic disulphide, although the analysis of the ore showed that volatile arsenic and sulphur were present in proportion to produce a condensate of arsenic trisulphide and sulphur. Distillation tests on the mineral arsenopyrite also produced a condensate of metallic arsenic and arsenic disulphide. This arsenic sulphide gave a distinct x-ray diffraction pattern which was not listed in the A.S.T.M. data file. This same sulphide can be produced by heating a mixture of arsenic and sulphur in vacuo. Its chemical analysis corresponds to As2S2. The dissociation pressures of arsenopyrite and the vapour pressures of arsenic disulphide and arsenic metal were measured, using a quartz "spoon" gauge. The dissociation pressures of arsenopyrite were compared with the published data for the dissociation pressures of pyrite to account

Jan 1, 1961

By R. Poulin, M. R. Samis

Real options valuation is an alternative net present value framework that is able to incorporate both management flexibility and dynamic project risks. In this paper, management is considering the development of a satellite low-grade zone while operations in a developed high-grade zone continue. If the lowgrade zone is developed prior to high-grade zone exhaustion, mine capacity must be expanded before additional production from the low-grade zone can be processed. This expansion can be avoided only if low-grade zone development is delayed until the high-grade zone is exhausted. The real option model presented here allows the development and capacity expansion decisions to be reconsidered on a discrete half-year basis. It delineates price regions, for given levels of high-grade zone reserves, in which it is optimal to develop the low-grade zone, defer low-grade zone development and abandon the mine irrevocably.

Jan 1, 2006

By D. Hu, L. Matzar, J. Hampton, M. Gutierrez

Nanodarcy permeability is common in many oil- and gas-bearing formations requiring unconventional stimulation technologies, such as hydraulic fracturing (HF), which can connect the isolated hydrocarbon-rich pores with a wellbore through induced fracture networks. Even though a dense induced fracture network is capable of accessing economic amounts of hydrocarbons, much of the rock between and very close to the fracture network is still un-accessed and contains extremely low permeability. Inducing fracture networks into brittle rock can create large amounts of micro failures in surrounding regions that are not connected to the wellbore, as can be seen in Fig. 1(a) from the very wide acoustic emissions (AEs) cloud associated with a narrow fracture generation. It is possible in certain types of rock to increase the effective matrix permeability in localized regions based on the damage associated with the surrounding hydraulic fractures and subsequent high stress concentrations along localized pre-existing potential failure zones. To study this problem, laboratory HF tests were performed at true-triaxial stress state in brittle crystalline rock while monitoring AEs. The AE associated with HF was analyzed for source parameters using the moment tensor inversion method called Simplified Green’s Functions for Moment Tensor Analysis (SiGMA). Using the moment tensor for each individual AE event, the mode of failure was determined. Crack slip directions and crack face normal directions were also found, along with the relative volume of individual micro failures as well as a damage parameter. The associated source parameters were used to classify differing regions of damage in the sample induced from HF and correlate these regions of differing damage to the effective drainage region. Shown in Fig. 1(b) is a near-wellbore (NWB) region that contained three times larger average relative volumetric deformation of individual tensile AE events than the average tensile AE event volume from the entire sample. Because of the large difference in micro fracture volumetric deformation for the NWB region compared to the entire sample, predictions of HF induced damage must be included in reservoir drainage predictions.

Jan 1, 2015

By J. A. Chamberlain

DURING a recent trip across Canada and parts of the northern United States, the. writer examined some forty mine models. Construction -details and the uses to which the models were being put were outlined in a report to Eldorado Mining and Refining, Limited, and a specific model was proposed on the basis of the Company's particular needs at their Beaverlodge operation. It was felt, however, that portions of the report would be of some value to anyone contemplating building a mine model. For this reason, a synopsis of some of the more important aspects of the problem is presented here, together with a suggested model type that appears to have wide application. Thanks are due not only to Eldorado for permission to publish the following material, but also to the many mine personnel across Canada who allowed the writer to examine their models and gave freely of their time in discussion.

Jan 1, 1958

By Norman B. Davis

THE ceramic group of industries is comprised of those engaged in the manufacture of cement, glass, artificial abrasives, whiteware, including earthenware, stoneware, porcelain tableware, porcelain sanitary ware, electrical porcelain, floor and wall tile, porcelain enamel on metals, refractories of all kinds, sewer-pipe and structural clay products, such as terra cotta, brick, and hollow tile. The various sub-divisions of the industry produce a wide range of articles on which we depend for our creature comforts from day to day, perhaps to a greater extent than we generally realize. The industry, in turn, depends on a great number of minerals, and chemical products derived from minerals, and it is the object of this brief paper to present a list of these with notes indicating the particular applications. In order to bring home the importance of the industry to your daily life, stop and consider the many things around you accepted as a matter of course. Cement provides the smooth surfaces of many of our highways, city streets, and sidewalks. It enters into nearly all types of construction, alone or in combination with other clay products. Glass we hardly appreciate because we can see through it so easily, but it is there to serve us in windows, doors, and other light-transmitting structures. Glass is the universal means of transporting liquids and beverages, our beverages are usually served in it, and, with the recent development in fine spun glass textiles, there is a possibility of glass clothing in the future. Chinaware, a general term for table dishes, may be earthenware (not vitrified), semi-porcelain, or bone china, but it is before us three or more times a day ?and we seldom think of the minerals that have made these products possible. Floor tile, wall tile, and other ceramic specialties for interior and exterior use and decoration please the eye and provide sanitary surroundings.

Jan 1, 1938

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983