Search Documents

By W. E. Lockley

This paper will attempt to answer a number of questions which are important to the safe and continued operation of an electric power system. 1. WHY should electrical protective devices be tested? 2. WHAT devices should be tested ? 3. WHEN should they be tested ? 4. HOW should they be tested? 5. WHO should test them ?

Jan 1, 1977

By E. J. Fuller, J. C. Monette

"Gold and silver cyanide complexes are presently desorbed from activated carbon by means of hot caustic elutions. These solutions may or may not contain additional sodium cyanide. There are several parameters which affect the rate of stripping. Some of these include pH, ionic strength, and temperature. (1) Stripping is conducted in recirculating (ZADRA) or once through (AARL) circuits.This paper describes the development of a new chemical eluant which significantly increases the rate of stripping of both gold and silver cyanide complexes from activated carbon. Two case history applications are also described.INTRODUCTIONAdditional cyanide is used in strip circuits in order to prevent its depletion which could lead to precipitation of base metals or lead to a change in the nature of the gold cyanide complex to one which does not strip as easily. (2)The strip circuits that are able to function efficiently without the use of cyanide are mostly those where the carbon is acid-cleaned after stripping.Once the minimum cyanide requirement to maintain the complexes in their proper state are fullfilled, any futher incremental increase in the level of cyanide will have no bearing on the rate of stripping. (3)DEVELOPMENT OF THE NEW ELUANTGeneral DiscussionVarious carboxylated materials were investigated including octanoic acid, polycarboxylic acid (various molecular weights), salicylic acid, polymaleic acid, acetic acid. benzoic acid, terephthalic acid, 4, bi-phenyl carboxylic acid, phosphoric acid and stearic acid.The initial work was done on medium activiiy, non acid-cleaned carbon. The silver to gold ratio on the carbon varied greatly.Two different blanks were used. The first was an elution using a 2% caustic and 0.4% cyanide solution while the second was a 2% caustic elution."

Jan 1, 1992

By Martin Junker

This Notwithstanding all the debates on climate change and renewable energy, coal remains the world's no.1 primary energy source even in the 21st century. In 2011 alone, total output rose from 420 million t to around 6.6 billion t. Similar growth rates are also expected for the next few years. In order to meet demand, new seams are being tapped and others mined far more extensively. In most cases, this means a move from open-cast to deep mining, and extracting coal from ever greater depths. At the same time, extraction processes such as the room and pillar method are being replaced by longwall mining, which significantly increases seam yield and therefore output. The depth of extraction with new, modified mining methods is increasing rapidly around the world - in most countries, much more rapidly than the corresponding expertise. A trade in mining expertise has therefore developed alongside the coal trade proper. Germany relies on coal imports, but can export mining industry services and advanced mining equipment. Geological conditions in the Ruhr and Saar coalfields forced Germany to drive forward development of deep working for hard coal years ago. For 30 years now, Germany has been mining hard coal at depths of over 1,000 m, and excavation is now at depths up to 1,600 m. Deeper extraction and more extensive excavation posed new challenges for both miners and equipment. Intelligent logistics, modern roadway development methods and longwall mining with ploughs or shearers combined with optimised process coordination offered pioneering solutions - solutions to enable costeffective coal extraction in the long term without compromising safety. Countries such as Russia, the Ukraine, China and the Czech Republic, where extraction is now reaching similar depths, can now benefit from this experience: they do not need to go through the same process of trial and development, but can draw on Germany's findings and ultimately save on costs. Now, Germany is offering this knowledge and experience on the international market on a client- and deposit-specific basis to continue providing mining countries with safe and cost-effective coal mining solutions and secure the energy supply. The presentation gives a number of examples of how international mining companies have used expertise from Germany to better meet the challenges of deep mining.

Aug 1, 2013

By John F. Gartner

"Traditionally, the geologists of Canada have been occupied with the tasks of finding new mineral bodies, locating gas and oil fields or hunting for economic deposits of industrial minerals. A very minor percentage of graduate geologists have applied their skills to solution of the ""urban blight"" or employing their understanding of ""Nature"" for the optimum use of land by mankind. However, things are changing quickly. The role of the geologist in the planning process is being established. It is an exciting time! Geologists are now being consulted on a wide range of urban planning problems. These vary, tor example, from assessment of the geological environment for the new communities of Erin Mills and Meadowvale, which will have total populations in excess of 100,000 people (truly a satellite city), to a complete geological/ geohydrological assessment of the new sanitary landfill for the city of Guelph.Use of geologic techniques and methods for urban studies must be enhanced with certain skills not taught, in the past, to the geologist. These include airphoto interpretation, soil mechanics, geohydrology, municipal engineering and highway engineering to mention a few. The geologist has the unique training to assess the natural environment and to discover, warn and explain the implications of man's attempt to command his environment."

Jan 1, 1972

By A. G. Roach

Introduction This paper deals with the operations and plant of the Craigmont Corundum Project, formerly of Wartime Metals Corporation but now under the Mines Section of the Resources Development Branch of the Department of Reconstruction and Supply. Corundum is recovered by the re-treatment of an old tailing deposit at Craigmont, Ontario. Crude concentrates so produced are shipped to the plant of the American Abrasives Company, Inc., at Westfield, Mass., for final processing and distribution to the abrasive industry. The plant was recently described in a paper entitled Craigmont Corundum which was presented by the writer before the Chicago meeting of the A.I .M.E. in February, 1946. General The Project is located on? lots 4 and 5, concession XVIII, township of Raglan, Renfrew county, Ontario, near the village of Combermere, which is on Highway 62. The property is about 135 miles from Ottawa. The general area enjoys a pleasant climate with moderate summer temperatures, though the winters are rather severe, the mercury frequently falling to - 35 deg. F. The excellent boating, fishing, and hunting have made the district a favourite resort for tourists. Lumbering is the main industry. Some farming is carried on, but the soil is poor and much of the land is hilly and rocky. There are no other operating mines in the immediate vicinity, though several 'industrial minerals', including mica, feldspar, nepheline, beryl, socialite, and others have been produced in the area. The district is drained by the York and Madawaska rivers and is generously dotted with large and small lakes. The general elevation is about 1,000 feet above sea level, though numerous hills rising several hundred feet give a rolling appearance to the landscape.

Jan 1, 1946

By Ursula M. Franklin

Old iron nails are one of the most common objects which entice the general public to ask questions about the history of metallurgy. There is a lot of history in old nails - history of the manufacturing industry, and social and economic history. Nails, therefore, are fine teaching tools; whether students have to acquire metallurgical skills or explore the structure and properties of wrought iron, whether they want to look into the history of inventions and the development of machinery, studying nails tells a story better than any teacher or any book. I have used this approach often and the following note is based on several student projects, particularly the work of Carmina Herrero and Vicky Marchant. Nails, those essential metallic fasteners, have long been with us. Their size, shape and design is basically a compromise between the makers' ability to control and manipulate material and the demands of the intended application. There were copper and bronze nails in antiquity, but in this paper I want to deal only with iron nails. In Rome, iron nails were common, and Cleere carried out the fine metallographic investigations on a large stock of nails recovered from a Roman fort site in Scotland. Those nails were hand forged; sorting them at the site on the basis of length, shape of head and shape of shank (in cross section) indicated that there seemed to have been some nail standardization. It appears that the Roman smiths used a series of heading dies starting with a 1/s-in. size. Each successive size increased by approximately 1/16-in. The metallographic inspection of the microstructures of the nails showed that the smaller nails were made in the one operation; i.e. both the tapering and the formation were accomplished on the heated rod without reheating. However, in the case of the larger nails, the nail had to be reheated for the tapering after the head had been forged. Most nails were tapered on all four sides of the shank and the shanks were square in cross section; only one group had rounded shanks. Most heads were flat disks, but in one group the heads were pyramids and another group had conic heads. Figure 1 shows the procedure used to produce the pyramidal heads. Obviously, Roman nail making was sophisticated and each nail design was meant for a particular use.

Jan 1, 1999

By G. Scott Zimmer

Mine planning at Cassiar consists of an annual cycle of projection, control, evaluation and revision following completion of annual diamond drilling during the summer months . The inherent difficulty in evaluating fibre grade and distribution, combined with a high-wall phase or push-back mining system, requires continuous modification to designs and schedules based on a cumulative evaluation of equipment performance and prediction versus production. To expedite the planning sequence, a mini-computer system has been introduced which allows emphasis to be placed on optimizing designs, exempting personnel from manual calculations and tabulations.

Jan 1, 1978

By A. E. Lehmberg

"IT IS KNOWN that some ores of sulphide type, such as pyrite, chalcopyrite, and bornite have an electrical conductivity comparable to that of metals, and accordingly much higher than the conductivity of any unmineralized rock. This physical property has long been used for the detection of orebodies of this kind by means of electrical measurements made at the surface of the ground.The present paper will deal with a new electromagnetic instrument for the investigation of subsurface conductors, which has been recently introduced into field practice and has already led to successful results in Canada.The principle of the instrument will be described. How it operates, and how the observations made can be interpreted will be explained. Field examples will •be shown to illustrate its application.Description of Instrument and of Operating TechniqueThe equipment (1) includes a low-frequency alternating current generator. The a.c. is supplied to a transmitter coil and generates a primary field which induces eddy currents in the ground, the intensity of which is proportional to the ground conductivity."

Jan 1, 1952

By G. De Gregoriis, G. E. da Mota, H. P. Dias, J. E. M. Blasques

In recent years, like many other smelters around the world, Albras has been increasing line current. The necessary adjustments to the work practices and process variables need to be made on all potlines, which in this case means on 960 cells at the same time. It was a challenging task to adjust the process parameters to the new amperage. In July 2003 potlines 2, 3 and 4 were running at 1 73 kA and the goal at that time was to reach 180 kA. Preliminary trials with 180 kA were performed on a group of 10 boosted cells on potline 3 in order to investigate possible operational problems. It was decided to increase the amperage in three steps accompanied by continual evaluation of the state of the process. In July 2004 the target of 180 kA was achieved with good operational results. This paper presents the overall results, the parameter adjustments made during the amperage increase in the booster group and how the increase was implemented on the other potlines.

Jan 1, 2006

By M. Sakata, H. Hata, K. Haiki

"Most of the secondary ZnO contains fluorine (F) in large quantities. Serious troubles at the zinc electrowinning are occurred by the cathode corrosion caused by F, therefore we developed iron compounds as F-adsorbents used in zinc sulfate solution. The iron compounds can be reused repeatedly as F-adsorbents because they can adsorb/desorb F alternatively depending on the pH. Moreover, if the adsorptive capacity decreases, we can dissolve and re-synthesize them easily. In this paper, results of the experimental process which consists of five steps (leaching, F removal, Cl removal, purification and electrowinning) to produce high purity electrolytic zinc from the secondary ZnO are reported. INTRODUCTIONThe recycle material for zinc, secondary ZnO, contains large amounts of fluorine (F) and chlorine (Cl) which are halogen elements, compared with calcine obtained by roasting of zinc sulfide concentrate. The halogen elements cause adverse effects in the zinc electrowinning process and particularly F causes corrosion of aluminum cathode plates and eventually sticking of electrodeposited zinc and therefore, F concentration in the electrolyte is controlled to less than approximately 20 mg/L. There are several methods to remove F from secondary ZnO, such as leaching with Na2CO3 or NaOH solution [1-2], vaporizing in a rotary kiln by roasting at 1000 to 1200 degrees C [3-4]. However, up to the moment, there has been no effective method for the removal of F from zinc electrolyte and it has been a big obstacle in treatment of secondary ZnO in electrowining of zinc.The authors, therefore, developed an iron compound used as an adsorbent of F in the zinc sulfate solution [5-8]. This iron compound is Akaganeite that has a crystalline structure of ß-FeOOH. Akaganeite is synthesized by neutralization of FeCl3 solution containing a small amount of SO4 2- with Na2CO3. When this iron compound is immersed into weak acidified zinc sulfate solution, F in the solution is adsorbed. F adsorbed in the iron compound is removed by immersing in weak alkaline solution and the iron compound can be reused as F adsorbent."

Jan 1, 2012

By K. Woo

The increasing move to block cave mining methods (including sublevel and panel caving) to access deeper and lower grade ore deposits as near surface sources become exhausted raises questions as to the extent and magnitudes of caving-induced subsidence as it may affect strain-sensitive infrastructure on surface. Predicting these surface deformations is difficult as they tend to be discontinuous and asymmetric due to large movements around the cave controlled by geologic structures, rock mass heterogeneity and topographic effects. Of further impediment is the sparse number of case histories available, in which actual subsidence measurements are reported to provide guidance and empirical constraints for subsidence calculations. This study reports the development of an exhaustive and comprehensive database of available (i.e. public domain) subsidence data from block cave mining operations from around the world.

May 1, 2009

By R. J. R. Welwood, F. J. Grebenc

"Brunswick Mining and Smelting Corporation Ltd. (controlled by Noranda Mines Limited) operates two lead-zinccopper- silver mines approximately 20 miles inland from Bathurst, N.B. The principal No. 12 orebody is mined by underground methods; the second, the No. 6 orebody (6 miles away), is recovered by open-pit mining. No. 12 underground operations ar•e in two parallel massive sulphide orebodies about 400 ft apart, dipping at 75 to 80 degrees and plunging almost vertically. The initial mining phase involved longhole open stoping from the 1550 level to the crown pillar, with main levels at 150-ft intervals and sub-levels between at 75 ft. Stope dimensions average 120 ft long, 100 ft wide and 400 ft high, with alternate rib pillars as well as sill and crown pillars. Initially, ore was transferred through scram drifts below each stope by means of 125-hp electric slushers and 72-in. folding scrapers, being delivered to gravity ore-pass collection •systems feeding a primary jaw crusher below. Later, track and trackless drawpoints were utilized below most longhole open stopes and pillars. Rib pillars were recovered by longhole methods, with large blasts into a central slot and undercut, after adjacent stopes had been filled. Waste-rock stripping from No. 6 open pit has been supplied to No. 12 stopes as backfill, by means of gravityfill raises.In 1968, the decision was made to mine the remaining ore zones by mechanized cut-and-fill methods, utilizing Load-Haul-Dump equipment. Currently, approximately 60 per cent of No. 12 mine production comes from mechanized cut-and-fill mining. As before, backfill is supplied from No. 6 open pit stripping waste rock, which has been crushed to minus 6 in. The ultimate objective is to supply virtually all production requirements by mechanized cut-and-fill techniques. The No. 6 open pit, which commenced production in 1966, covers an area of 1,500 by 1,200 ft, equivalent to 41 acres approximately. Ramp roads are graded at 8.5 per cent. Each mining bench is 36 ft high and the ultimate pit will consist of 14 benches for a final pit depth of 504 ft. Present depth is 180 ft."

Jan 1, 1971

By Jos. Kalbhenn

PART of the plan of re-allocation evolved by the engineers of the Dominion Steel and Coal Corporation in 1932 to retard the rapid advance of the submarine workings seawards was the opening of Dominion No. 20 Colliery, in the Harbour seam, by a pair of cross-measure tunnels from the workings of an older mine working the Phelan seam, which lies 430 feet below the Harbour seam. The tunnels, 8 ft. by 13 ft. in size, were started away from the old workings of Dominion No. 2 at a point 1.5 miles beyond the shore line and were driven on a rising grade of 1 per cent for a distance of 5,335 feet, tapping the Harbour seam at a point 2 ¼ miles off-shore. For transportation and ventilation, shafts and roadways already existing in the Phelan seam were made use of during the stages of development and up to the present time. One of the two tunnels served as a main haulage road and an intake airway, and the other as a return airway and travelling road. However, as the workings of this new colliery expanded, the need for additional airways arose as was anticipated when the plans for the development were formulated. To meet this need, work was started on October 1st, 1942, to establish a new opening between Nos. 2 and 20 Collieries in the form of a vertical shaft to provide a passageway for the ventilating air current of some 250,000 cubic feet per minute on its return to the upcast shafts in No. 2 Colliery, thus making both tunnels available for intake airways. In the interest of safety, speed, and economy, the shaft was raised from the Phelan to the Harbour seam. It is 20 ft. by 12 ft. in size and, with the exception of three timbered compartments across the narrow end, is untimbered. One of the three timbered compartments housed the ventilating tubing and pipe lines, the centre one served as a cage-way for hoisting men and material during the operation of raising, and the third one contained a ladder way. The rest of the shaft was filled with debris during the period of shaft raising.

Jan 1, 1944

By B. G. Cousins, L. Racine, R. S. MacPhail

"FLEX 31 is a chemically enhanced sodium isopropyl xanthate that has shown improved collection properties over SIPX for copper-bearing and copper-activated minerals. Characteristics such as improvement of recoveries with lower dosages and high pyrite and pyrrhotite rejection capabilities have all been exhibited by FLEX 31.The most improved results have been seen insphalerite flotation. Plant trial work carried out in the zinc circuit at the Louvicourt Concentratorin northern Quebec has produced data showing superior grade and recoveries from rougher concentrates that previously had not been attain-able with other reagents effectively. The improvement over SIPX adds up to an almost$1,000,000 annual improvement on the mine’s bottom line at present zinc prices.IntroductionSodium Isopropyl Xanthate (SIPX) is one of the most popular flotation chemicals on the market today. Somewhat more specific than amyl xanthates, SIPX is used in a variety of ores like copper/zinc, lead/zinc, arsenopyrite/pyrite, and many others (Melis et al., 1991). An investigation carried out by Tennants Research Technology Applications (TRTA), a division of Charles Tennant & Co. (Canada) Ltd., produced a chemically enhanced SIPX that has shown all the advantages of normal SIPX along with improved recoveries of copper and copper activated minerals. The new product has been named FLEX 31. Currently, FLEX 31 is manufactured at the Prospec Chemicals, another division of Charles Tennant & Co. (Canada) Ltd.A large amount of laboratory testing pro-grams have been carried out with FLEX 31 todate (MacPhail and Cousins, 1995; Cousins and MacPhail, 1996). One of the minerals that has a defnite affinity to improved fotation is sphalerite (ZnS). Once activated with copper sulphate, sphalerite has produced some of the most spectacular test work when FLEX 31 is compared directly to SIPX. Plant trials of FLEX31 at Aur Louvicourt Inc. carried out in 1995show that FLEX 31 is far superior to SIPX for activated sphalerite flotation."

Jan 1, 1997

By S. L. Chen

The Kumera Technology Center developed a unique type of steam dryer for drying copper concentrate in the mid 1990s. The dryer has been chosen in several copper smelter projects since 1999. To expand production capacities, the Norddeutsche Affinerie smelter, the Pirdop smelter of Cumerio, the Toyo smelter of Sumitomo Metal Mining and the Tamano smelter of Hibi Kyodo Smelting have carried out projects in which Kumera Steam Dryers were installed. The capacity of a single steam dryer varies from 70 t/h to 160 t/h. This article summarizes the latest operation results of the Kumera Steam Dryers in these smelters and introduces the progress of the ongoing projects in Yanggu Xiangguang Copper, Guixi smelter of Jiangxi Copper, Jinlong Copper, Boliden Harjavalta, and Onsan smelter of LS-Nikko Copper.

Jan 1, 2007

By John Loui Porathur

Highwall Mining has been recently introduced in India. The first Continuous Highwall Mining extraction in India started operating at Ramagundem Opencast Project-II (OC-II) of Singareni Collieries Company Ltd. (SCCL) in December 2010. A new hybrid empirical and numerical modelling approach has been devised to design web pillars for the initial Highwall Mining sites in India, considering the complex geology, such as existence of thick seams and multiple seams in close proximity. This paper gives the scientific elucidation of a comprehensive design methodology adopted for the above mentioned Indian Highwall Mining sites. The design technology includes web pillar design for multiple seams using hybrid empirical and numerical methods, slope stability assessment, ground movement monitoring, and recommendations for conducting blasting operations in the vicinity of Highwall Mining extractions.

Aug 1, 2013

By F. A. Auld

"Traditionally deep shaft sinking from the ground surface was carried out using drill and blast methods. Although large diameter blind shaft drilling has been carried out successfully on numerous occasions previously, including as early as 1852 in Germany (Auld, 1995), little attempt has been made until more recently to mechanise the shaft sinking excavation process using down-the-hole machines. This paper reviews the development of deep shaft sinking machines from the early 1970’s up to the present day. INTRODUCTION Mechanical excavation methods can significantly improve excavation performance, in order to access natural resources faster, and labour safety is increased compared to drill and blast operations. However, shaft sinking machines need to be capable of accommodating all the basic requirements for deep shaft sinking, namely: 1. Excavation and muck removal 2. Ground stability control 3. Groundwater ingress control 4. Temporary lining installation 5. Permanent lining installation and watertight sealing 6. Ventilation 7. Secondary means of egress for personnel In addition, how the machine operates in the shaft is an important factor, either slung on ropes from a surface headgear or on its own in the bottom of the shaft. An all-embracing machine which can deal with all of the above conditions is impossible but many of these requirements can be incorporated into a single machine. Deep shaft sinking also differs greatly from normal tunnel construction which employs the use of either a roadheader arm installed within a shield or a full-face tunnelling machine for excavation. Hydrostatic pressure and ground stability problems increase with depth, whereas in tunnelling the depth is normally relatively shallow and the aforementioned factors remain approximately constant along the tunnel length. DEEP SHAFT SINKING MACHINES All the shaft sinking carried out previously in the UK was by the traditional method of drill and blast. Elsewhere, in other parts of the world, attempts have been made to mechanise the process."

Jan 1, 2019

By Luke Meers

Roadway development rates in Australian underground coal mines are failing to keep pace with modern longwall systems and are unlikely to sustain further improvements in longwall productivity into the future unless step change improvements to roadway development equipment and practices are made. Bottlenecks which limit and constrain improved production and impact the safety of operators have been identified through a series of industry surveys, with the manual installation of strata support materials, consumables delivery, coal haulage and monorail installation being highlighted as major areas to improve development performance. This paper looks at research being carried out at the University of Wollongong in designing an integrated system approach for the fully automated handling and installing of development consumables, and the systems required to support these activities. A series of hard automation manipulation devices have been demonstrated in surface trials and the results indicate that rapid roadway development can be achieved.

Aug 1, 2013

By L. T. Pasiechnyk

After a brief review of the various hydrocarbon storage methods currently being utilized and statistics on underground hydrocarbon storage, this paper will briefly describe the technology involved in solution mining salt to create caverns of engineered shape and size and briefly discuss the economical and environmental advantages of hydrocarbon storage in solution-mined salt caverns. Other possible uses of salt caverns will be mentioned.

Jan 1, 1978

By Sepulvedam Jaime E., Levi Guzmán Rivera

"Grinding media consumption rates and their dependence on key operating conditions in semiautogenous grinding mills is analyzed on the basis of a detailed mathematical model recently developed by Moly-Cop´s specialists which describes and takes into account the three primary media consumption mechanisms, namely: abrasion/corrosion, surface spalling and impact ball breakage. The influence of key mill operating conditions – such as ball filling, discharge grate opening, mill speed, lifter profile, and ball quality – on their corresponding grinding media consumption rates is explored via a variety of model simulations, discussing in every case the independent contribution of each of the indicated consumption mechanisms to the estimated total ball consumption rate.INTRODUCTIONA thorough understanding of the independent contribution of each grinding media wear mechanism is extremely important, especially in semi-autogenous grinding (SAG) operations where macrowear (spalling) and ball breakage cannot be ignored or neglected. The high impact conditions imposed in modern SAG milling environments has created serious challenges for grinding media manufacturers since their products must be able to perform with minimal breakage and surface spalling.GRINDING MEDIA WEAR MECHANISMFor SAG milling operations, at least 3 different mechanisms have been identified as the main contributors to the observed overall grinding media consumption, here referred to as: abrasion / corrosion, ball breakage and surface spalling.Wear by Abrasion/CorrosionThe abrasive/corrosive wear mechanism has been discussed in depth in previous publications (Benavente Hector, 2007; Guzman Levi, 2014; Sepulveda and Morrow, 2014). The most widely accepted approach to mathematically characterize the consumption (wear) kinetics of grinding media in rotary tumbling mills is known as the Linear Wear Theory (Prentice, 1943; Norquist, 1950; Sepulveda, 2004) which claims that—at each instant 't' after a grinding body enters the mill load—the rate at which the body loses weight is directly proportional to its surface area exposed."

Jan 1, 2016