Search Documents

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. In order to clarify the failure mode, fracture surfaces after tensile tests were observed by scanning electron microscopy (SEM). The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles, lamellar structure elongated in the rolling direction contains lamellar boundaries was formed. With increasing the strain, mean spacing of lamellar boundaries decreased. Finally, continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. The tensile strength and hardness of the 6 cycle ARB processed 5083 aluminum alloy sheet increased about two and three times of the initial values, respectively. Results indicated conformity between mechanical evolutions and microstructural changes during ARB process. Fracture surfaces observations showed that failure mode in ARB processed aluminum is shear ductile rupture with elongated small dimples.

Oct 1, 2011

By R. Sage, N. Rillette, M. D. Everell, G. Herget

"CANMET has been operating as a Government Technology Centre for two years. Many of CANMET's programs involve long-term research and require special expertise, often available at Canadian universities. CANMET's involvement with universities ranges from research grants and contracts to exchanges of scientists and joint use of research facililies. Examples of CANMET - university cooperation in mining are presented. IntroductionIn the last two years or so CANMET has undergone a significant metamorphosis, resulting in greater emphasis on applied research to enhance Canada's industrial capability. CANMET's new mandate is reflected in the types of projects undertaken and their categorization, (Fig . I). Emphasis is being placed on two project categories: strategic R&D, to enable CANMET to serve the changing technological needs of the industry; and incrernental R&D, to serve the more immediate industry needs through modifications to existing technologies and knowledge. The balance of CANMET's e ffor t is devoted to providing Mandated and Specialized Services, and to Exploratory Research.CANMET interaction with universities can involve one of several available vehicles : contracts, research grants, exchanges of scientists , student employment and nomination of professors on CANMET's advisory council. Instances of key university technical support to CANMET mining projects are highlighted."

Jan 1, 1990

By K. O. J. Sidwell

STRATMAT LIMITED, through its subsidiary, the Strategic Manganese Corporation, controls two adjoining iron-manganese properties five miles west of Woodstock, New Brunswick. One is a staked property of 77 claims traversed by one trunk highway, several secondary roads, and a branch line of the Canadian National railway. The other property, a 20-square-mile Concession immediately to the north-east, is also traversed by an excellent network of roads. Both proper-ties are situated in gently rolling farmland. The deposits were discovered in 1836 by Dr. C. T. Jackson. The first attempt to exploit them was made in 1848 when a blast furnace was erected with a capacity of 7 tons per day. The ore was mined by a series of deep trenches that followed the folds of the enclosing slates. In the late years of operation, bog iron ore from Burton and Maugerville, in Sunbury county, was used in conjunction with the Wood-stock ore. An additional 5-ton furnace was erected in 1863 and mining was carried on intermittently until 1884. No further extensive work was done until 1953. During the period of activity, approximately 70,-000 tons of ore are said to have been smelted ( 1). During these earl y operations the Iron Ore Hill and Moody Hill deposits were partially opened, with the ?bulk of the furnace feed being mined from the Iron Ore Hill workings. The low tenor and apparently limited extent of the deposits, the high. ?content of phosphorus, and the increasing scarcity of fuel, were the chief factors that brought the enterprise to an end.

Jan 1, 1957

By James McMahon

Although doubt has been expressed many times as to who first brought self-contained breathing apparatus to this side of the Atlantic, there is none whatever that the first organized station was established at Glace Bay, N .S., by the Dominion Coal Company, in 1907. This station was started with 20 sets of 1907 "Draeger" apparatus and all necessary station equipment and supplies. After the fire at No. 1 pit, Sydney Mines, in 1908, the Nova Scotia Steel Company installed 15 sets of "Draeger" and sup-plies, which were housed in a rescue car (a converted pull-man.) In 1909 or '10 a fire occurred at the Back Pit, Stellarton, where the apparatus from Glace Bay was used, and subsequently the Acadia Company erected a station and in-stalled 10 sets of "Securitas" apparatus. In 1912 the station at New Waterford was opened and equipped with "Draeger," and the same year the station at Springhill was built and equipped with the same type. Sometime during past years the Nova Scotia Steel Company acquired a couple of "Proto" machines, and after the explosion at the Allan shaft in 1918 the Acadia Coal Company added some "Gibbs" to their station. From this it will be seen that when the coal-fields were organized under the British Empire Steel Corporation the equipment was rather mixed, therefore steps were taken by the executive to stanardize the whole of the rescue and recovery work.

Jan 1, 1924

By C. O. Stee

IN the October, 1936, issue of the Canadian Mining Journal there was published a series of very comprehensive and exccellently illustrated papers by Mr. C. O. Stee and members of his staff dealing with Siscoe operations and ore-bodies. These were, in the order in which they appeared: Geology of Siscoe Gold Mine, by O. L. BACKMAN Diesel Power at Siscoe Gold Mines, Ltd., by C. O. STEE andE. A. BLOMQUIST Mining at Siscoe, by L. T. POSTLE and W. F. Engineering and Surveying, Siscoe Milling Practice, Research and Testing Laboratory, Assaying of Mill Tails and Solutions, BROWN(6) by P. A. TEEPLE (7) by L. E. DJINGHEUZTAN by L. RIVETT (8) by G. IRWIN (9) The Editor of the Canadian Mining Journal cordially assented to our suggestion that these papers be reviewed at the 1937 Annual General Meeting of the Institute, and the authors very kindly accepted our invitation to present such reviews . Of these courtesies, full acknowledgment is here accorded. To our readers, we commend the original papers in the Canadian Mining Journal. The summaries presented at the meeting follow. EDITOR. THE GEOGLY OF THE SISCOE MINE The Siscoe gold deposits lie in and near a stock of granodiorite, related to the Bourlamaque batholith, which has intruded highly folded Keewatin volcanic rocks .. The volcanic rocks lie to the north of a belt of Timiskaming sediments.

Jan 1, 1937

By A. A. Brant

ONE of the reasons advanced for the decline in prospecting and discovery is that, as regards surficial examination, the law of diminishing returns is becoming applicable. Fewer surficially unprospected fields remain; therefore, fewer discoveries by such means result. Much in the nature of mineral resources remains to be unearthed, but even now, and more so in the future, will discovery depend on painstaking petrographic and structural mapping, aided, where necessary, by judicious applications of all the complementary scientific knowledge and devices (e.g., thin section microscopy, geophysics, and drilling) that experience proves effective in localizing a mineral deposit even beneath drift, lake, or muskeg. It is to be expected, then, that the rate of discovery will decrease, that the cost per discovery will greatly increase, and that the work of discovery will become more and more the careful, methodical assembling of field data, conscientiously interpreted on the basis of scientific knowledge by trained, experienced operatives. In view of these trends, the status of applied geophysics to Canadian mining exploration and development work might well be reviewed. The niche which geophysics may occupy relative to geological surveying and drilling has been clarified by the last twenty years' experience. The cloud of somewhat justifiable scepticism that followed the 'geophysical promotion' period of the late 1920's has lifted. Mining, exploration, and finance companies, in open-minded fashion, are seeking sound advice as to what are the scope and limitations of the geophysical methods at present practised. The purpose of this paper and the following one is, therefore, as far as lies within the author's power, to review briefly the geophysical methods at present in practice in Canada, and, at greater length, to joint out impartially and critically their scope, merits, shortcomings, an possible future development. The treatment will be non-technical, the hope being that an accurate statement of the present status of geophysics in Canada may do much to result in a sounder, saner growth of what, in the future, shall undoubted} y prove an increasingly useful tool in exploration and development work. ?

Jan 1, 1942

By M. F. Goudge

This paper is intended to call attention to the manifold uses of limestone in industry; to indicate the types of limestone desired by some of the large consuming industries; and to give some information on the resources of limestone in Canada, so that an idea may be obtained of the present and future possibilities for limestone production. The word limestone is used in the usual broad sense to include both high-calcium limestone and the highly magnesian variety known as dolomite, as well as all intermediate types. Lime is simply calcined limestone, and in this general paper its uses have been included with those of raw limestone. It is of interest, in dealing with this subject, to glance back over the early history of the utilization of limestone, for by so doing we see that limestone has been of importance to mankind since the beginning of civilization and has contributed in no small measure to the development of a number of the arts and sciences. One of the first uses, if not the first use, of limestone was in connection with the making of lime for plastering purposes. This use antedates civilization. In the day of the ancient Greeks and Romans, the art of plastering had been brought to a state of perfection that is not nearly approached by the modern artisan.

Jan 1, 1930

By T. W. Wlodek

Abstract A simplified method of fatigue testing full-dimension, as-rolled, non-machined, mining drill rods is very desirable to the mining and steel industries in the classification of steels available on the market, through the evaluation of their fatigue limits and endurance strength. In this paper one such simplified method is presented and analysed. The preliminary results show many advantages of this method, such as simplicity and constancy of loading. The type of loading applied more or less simulates the working conditions of the outside fibres of the mining drill rods. Additional advantages of this method are the possibility of testing under dry and wet conditions, its quietness, and its ease of operation. Specially designed adaptors and specially applied techniques of fixing and preparation of samples make possible the breaking of a quarter-octagon hollow drill rod in a free length of uniform section in a rotating beam machine. At first glance this seems to be difficult to achieve. In the first preliminary test three different lots of steel were used. S-N curves under dry conditions were determined. These curves permit of the classification of the drill rods on the basis of the fatigue limit and endurance strength of the outside fibres of the metal, which is dependent to a greater or lesser extent on the effect of surface decarburization, surface imperfections, and special surface treatments. The average slope of the S.N curve in the damaging zone, and the fatigue limit in equal tension-compression rotating bending, were determined for SAE 1080, chromium-molybdenum and nickel-chromium-molybdenum mining drill rods. INTRODUCTION The fatigue limit and the endurance strength of mining drill rod steels are of interest to both the mining and the steel industries. These industries are greatly interested in lowering the cost of mining by reducing the consumption of these steels per ton of ore exploited.

Jan 1, 1951

By Steven Hart

In September 2009, Newmont began the commissioning of a 3 stage crushing and milling circuit at its Boddington Gold Operation in Western Australia. The Boddington ore has been recognized as one of the hardest and most abrasive ores treated to date and this played a pivotal role in the selection of crushing and HPGR technology for this operation as opposed to the more conventional SABC circuit. This paper will examine the scale up from laboratory to pilot plant and full scale operation of the crushing circuit. There have been many challenges to overcome in the first 18 months of operation; however, the HPGRs have in general met design expectations and performance is expected to improve further with ongoing design changes

Jan 1, 2012

"10.1. IntroductionAs discussed by Westland (1981), the six platinum-group elements (PGE) belong to the Group VIII transition metals, to which iron, nickel and cobalt also belong. The chemical similarity between these nine metals accounts for the fact that they tend to be concentrated together as a result of geological processes. These processes started to effect the distribution of these metals at the very beginning of the earth's history.The first line in Table 1 gives the concentration of nickel and certain other Group VIII transition metals in carbonaceous chondrites, those meteorites with a composition that is believed to reflect best the composition of our planetary system apart from hydrogen and helium. The second line is the estimated concentration of the same elements in the earth as a whole. It is seen that these two estimates are quite similar, the earth being perhaps 2 to 3 times richer in these particular metals than the planetary system as a whole. The reason for this is not fully understood, but it may be due to the earth being formed by the accumulation and capture of a greater proportion of iron (and therefore siderophile-rich) than stoney (and therefore siderophile-poor) planetesimals than the planetary system itself.The third line in Table 1 is the average composition of the crust of the earth. With the exception of iron, all of the Group VIII transition elements are rare in the crust, present at concentrations of It tOO to Itt ,000 of that of the bulk earth. This is because the outstanding chemical characteristic of this group of elements is their siderophile nature; that is, their tendency to alloy with metallic iron. Because of this, once the earth became molten very early in its life history, these elements dissolved in the molten iron present at this stage and were removed from the outer accessible parts as this dense liquid sank to the centre of the earth to form the core. Although iron was the main instrument of concentration of the Group VIII metals, its much greater over-all abundance and its ability to combine with oxygen more easily than the others in the group means that significant amounts still remain in the oxidized portions of the earth.The fact that most of the Group VIII metals are available to use in workable concentrations at all is that they are 5 to 30 times more concentrated in the earth's mantle than the crust, as shown in line 4 of Table I. There has been a constant, if slow, interchange of matter between the mantle and the overlying crust throughout most of the earth's history and, under certain circumstances, this interchange has given rise to economic concentrations of metals."

Jan 1, 1979

By A J. Kyle

After a brief description of the shaft and surface facilities, this paper describes the planning for the mining operation, the selection of equipment the general method of mining and the sequence of operation. All of the major items of equipment are described, including the components of the power system. The detailed planning is reviewed -from the shaft sinking to the three-shift mining operation. Excavation and equipment changes, as well as long-range planning, are al o di cussed. Introduction THE successful completion of the Yarbo No. 1 shaft of International Minerals & Chemical Corporation (Canada) Limited in July, 1962, added a new type of mine to Canada&apos;s many producing operations. IMC Esterhazy is a unique mining operation in Canada; in fact, it is unique to potash mining in general. Not only is thi&apos;3 a trackless operation utilizing shuttle cars and belt conveyors in its material handling systems, but it excavates all of the ore with continuous boring machine<:;.

Jan 1, 1964

By G. D. Markland

"The Moose Mountain mine is located in a belt of Precambrian volcanic rocks situated 20 miles north of Sudbury, Ontario. It was the first iron mining operation in the Archean iron-formations of the Canadian Shield.The ore is believed to have been formed in an environment of active volcanism, being part of a pyroclastic and volcanic series where only the iron-formation and chert qualify as chemical sediments. The volcanic environment, subsequent regional tectonics and metamorphism produced orebodies which differ from the main sedimentary iron ranges of the world in such features as continuity, grade, structure and metallurgical characteristics. The orebodies occur as relatively small lenses which have been complexly folded, faulted and intruded by acidic and basic dykesAlthough the basic mining and beneficiation methods are simple, detailed geological control in exploration, planning and operation has been necessary to apply detailed selective techniques to the large-scale open-pit methods necessary in profitable iron mining.The milling and pelletizing processes are sensitive to minor variations in ore grade, grain size, fabric and mineralogy. Although detailed correlations of geological information and mill performance are still not entirely satisfactory, general working relationships have been determined with simple testing procedures. These are of in-creasing use in forecasting production and in ore-blending processes.The application of geology to mining and milling operations at Moose Mountain represents a departure from general practice in iron ore operations."

Jan 1, 1966

By G. D. Markland

The Moose Mountain mine is located in a belt of Precambrian volcanic rocks situated 20 miles north of Sudbury, Ontario. It was the first iron mining operation in the Archean iron-formations of the Canadian Shield. The ore is believed to have been formed in an environment of active volcanism, being part of a pyroclastic and volcanic series where only the iron-formation and chert qualify as chemical sediments. The volcanic environment, subsequent regional tectonics and metamorphism produced orebodies which differ from the main sedimentary iron ranges of the world in such features as continuity, grade, structure and metallurgical characteristics. The orebodies occur as relatively small lenses which have been complexly folded, faulted and intruded by acidic and basic dykes.

Feb 1, 1966

By Horace Freeman

The sulphur consumed in Canadian pulp mills and acid plants is worth approximately three million dollars annually and amounts to one hundred and fifty thousand long tons, all of which is imported from the United States. Concurrently with a decline in the value of newsprint there has been a gradual increase in the price of this raw material. Most pulp mills in Canada are situated within reasonable distance of domestic pyrite deposits; nevertheless it has not yet been found possible to mine these deposits and utilize the contained sulphur in competition with the imported material. It is the purpose of this paper to elucidate the reasons therefor, and to describe? a commercial-scale experiment undertaken with the object of introducing a native raw material into the Canadian pulp industry on the purely economic basis. Reasons for the Preferred use of Sulphur The known sulphur deposits in the United States are very large, so that at least a twenty-year supply of this material is assured. It is recovered cheaply and in pure condition. Although large deposits of pyrite are known in Canada, nothing has yet been developed to compare in size, cost of mining, or purity with the United States material. It has been necessary to handle and transport more than two tons of pyrite to equal a ton of sulphur.

Jan 1, 1930

By J. F. J. Thomas

"AbstractBoth the quantity and quality of waters available as raw materials are important to Canadian industry and to the national economy. The huge demands of many Canadian industries is illustrated by tabulated figures, based on the 1950 Canadian production of certain products, and on United States figures for the gallons of water required to produce a unit quantity of each product. It is suggested from comparison with American survey results and figures that Canadian industrial water consumption is 1 to 11/2 billion Imperial gallons per day. Since present information on Canadian usage is meagre and it is not certain that American survey results can be directly applied to Canadian industry, this estimate must await confirmation in future studies.The hydrologic cycle and the principal factors affecting the quantity and quality of water, namely, climate and season, topography, geology, vegetation, and human activities, are discussed and the principal salts dissolved in water which affect industrial use are enumerated.The present survey studies by the Mines Branch on water quality are outlined. Besides chemical analyses of municipal water supplies within a watershed, periodic sampling and analyses of major surface waters for a one-year period is being carried out. The importance of studies on seasonal variation in quality is stressed by comparing the dissolved salts in various river waters with river flow. Figures showing such relationships in the Rideau river and Ottawa river at Ottawa, the Columbia river at Trail, B.C., and the Battle river at Unwin, Sask., are presented. Different rivers show different quality changes with changing flow, and possibly only after long-term studies can the relationships be predicted.Quality studies on water may be as important as studies on many other raw materials. The quantity of the raw material, water, is not inexhaustible nor is the quality indestructible, and more realization of its importance, followed by conservation and intelligent use, is desirable."

Jan 1, 1952

By D. C. Reid

This paper describes the latest results in research and development currently being undertaken by the CSIRO Mining Technology Group to advance the automation capability of continuous mining equipment in underground coal mining operations. This research delivers enabling technologies that are essential in achieving increased roadway development rates as well as providing a safer working environment for underground mine personnel. Details are presented on technical developments and results of large-scale above-ground experiments conducted under field-realistic conditions. These experiments demonstrate the performance of the ?self-steering? capability which will enable a continuous miner (CM) to automatically maintain a given mining heading and mining horizon under production conditions. A primary technical requirement of this automated functionality is the means to accurately determine both the location and orientation of the CM in real-time. Test results of a high performance navigation system utilising vehicle motion aiding technologies are presented. This system combines high performance inertial sensors, and custom-developed radar to achieve a navigation-grade guidance system. Comprehensive performance evaluation has been conducted using a scale skid-steer mobility platform operating autonomously through a typical roadway development mining pattern with a total path length of 2700 m and mission duration of 112 min. Results from this evaluation demonstrate that the sustained accuracy of the navigation system exceeds the original project expectations and is well suited to the requirements for this underground mining application. There are presently no known alternative methods for providing a practical and accurate three-dimensional guidance solution in this application. This achievement represents a significant milestone in delivering a step change improvement in underground coal mining roadway development.

Aug 1, 2013

By A. S. Gendron

A brief description of Inco&apos;s ORC copper refinery tankhouse and the electrowinning tankhouse is followed by a comparison of the requirements for the production of the high-quality copper in both systems. The description will focus on both tankhouses, with emphasis on experience to date in the electrowinning tankhouse. Particular attention will be paid to sensitivities of each tankhouse to process upsets which can. significantly afject the quality of the product cathodes.

Jan 1, 1977

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of the overall study, a comprehensive description of physical and chemical characteristics of fine tailings generated by caustic and non-caustic processes was carried out. Ultimately, the influence of these fundamental properties on the compressibility, hydraulic conductivity and shear strength properties of the fine tailings was assessed. The characteristics of the fine tailings are presented in terms of index properties, mineralogy, specific surface area, water chemistry, liquid limits, particle size distribution and structure. A difference in water chemistry was concluded to be the cause of substantial differences in particle size distributions and degree of dispersion of the comparable caustic and non-caustic fine tailings. The degree of dispersion was consistent with predictions for dispersed clays established by the sodium adsorption ratio (SAR) values for these materials. A linear variation of increasing dispersion with increasing SAR up to a SAR value of about 40 has been suggested, above which fine tailings are completely dispersed. The observed dispersed or flocculated structures (viewed using a scanning electron microscope) supported the predictions based on SAR values.

Jan 1, 2010

By B. W. Smee

Glacial lake sediments or glaciolacustrine deposits form a significant portion of the Canadian, Scandinavian and Russian landscapes. Furthermore, 50 per cent of the Archean volcanic belts within the Canadian Shield area are covered wholly or in part by these deposits. Because of the high electrical conductivity and low hydraulic conductivity of these compact sediments, the application of geophysical (electrical) and geochemical techniques in such areas becomes a difficult task. The presence of these sediments has therefore hampered exploration for metallic sulphide deposits in some of the most important metallogenic environments of Canada. Similar problems exist in some tropical countries, such as Australia, where the overburden may be very conductive. In this paper, the extent and provenance of the glaciolacustrine deposits within the Canadian Shield are described. The geochemical and geophysical factors that hinder exploration in the clay belts are reviewed, with case histories of successful and unsuccessful applications of some of these techniques. The most successful geochemical technique used within glacial clay belts is the sampling of lodgement till beneath the clay cover, and the analysis of the heavy mineral fraction of that till. Surficial sampling has not been successfully applied. Some geophysical techniques, more specifically electromagnetic and magnetic induced-polarization techniques, have detected mineralization beneath substantially deep clay or saline overburden layers. Some suggestions have been made, such as the use of anions in hydrogeochemical surveys and the use of wide-band multi-frequency EM systems. When implemented, they will hopefully make the current geochemical and geophysical methods more effective in exploration for base metal sulphides within clay-covered terrains.

Jan 1, 1979

By Jason Berenyi

Presentation Overview ? What is Potash? ? Where are the potash deposits? ? Current potash mines ? production, capacity and planned upgrades ? Saskatchewan Saskatchewan?s Potash Production Potential s ? Current Status of Potash Exploration ? Increasing Demand for Potash ? Saskatchewan global role

May 1, 2009