Search Documents

By L. Veleva, Garcia. A., G. Perez

Aluminum is a metal used for the transmission of electricity of high voltage, in the construction industry and other areas. In atmospheric conditions aluminum forms an oxide layer (Alz03'H20) as a result of its corrosion, entering the passive state. The oxide layer can be destroyed by the presence of ions (Cr, SOx-n) developing localized (non uniform) corrosion attack by pitting, difficult for evaluation. The concepts of fractals and self-similarity were used in this study for the characterization of the development of localized corrosion. Images obtained with a scanning electron microscope (SEM) of samples of electrolytic aluminum wire that have been exposed during one year in ruralurban and marine-coastal environments of the humid tropical climate of Mexico, have been processed. The development of pitting has been studied as a function of time, making a statistics of the frequency of appearance of pits versus the area occupied by them. The data show that the distribution of the pits follows a power law. Therefore, the concept of self-similarity can be applied for the study of the phenomenon of localized corrosion, describing their development with time.

Jan 1, 2006

By H. R. Shakeri, R. Mayer, M. J. Worswick, A. Rahem

The current focus of research and development in transportation industry is to use lightweight materials such as aluminium alloys for more structural components. In this regard, maintaining safety of the passenger and vehicle is the most important; therefore crashworthiness of components made of lightweight materials must be evaluated prior to sizable application of these materials. The focus of the present study is to understand failure and damage mechanisms during the axial crushing of aluminium tubes made of A1Mg3.5Mn alloy of 2 and 3.5 mm thickness. Due mainly to complexity of the crushed tubes, a microstructural approach is considered. In this study optical, stereo as well as scanning electron microscopy techniques have been used to study damage and failure mechanisms in these types of tubes, which are essential energy absorbing components in passenger vehicles.

Jan 1, 2006

By Northeastern University, B. Y. Cui, B. Y. Wang, D. Z. Wei, W. G. Liu, Z. C. Guan, S. L. Gao

To recover iron values from low grade ores by reverse froth flotation method, further research on cationic collectors used in reverse flotation of iron ores is launched to promote the utilization efficiency of iron ores. In this paper, one new cationic surfactant, bis(2-hydroxylethyl) dodecylamine (BHD), that could be dissolved in water easily was used as collector for quartz flotation. Flotation results indicated that BHD shows stronger collecting performance on quartz than hematite. The maximum recovery of 96.30% to quartz is obtained at a collector concentration of 20.0 mg/L in the pulp pH range from 5 to 7. This collector can be used to float quartz from hematite. And optimal separation results with 86.59% iron recovery and 66.60% iron grade to synthetic sample were achieved at a collector concentration of 20.0 mg/L and pulp pH of 5.02 when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by XPS analysis, infrared spectroscopic analysis and zeta-potential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occur between collector and quartz surface.

Jan 1, 2016

By S. Sundararajan, J. Brousseau, P. Bocher, M. Galopin, N. Barka

This research is committed to the prediction of the hardness profile produced by induction heating, using a computer-modeling software. The paper presents the simulation of the induction hardening process to analyse the sensitivity of the induction parameters on the hardness profile of a low alloy steel specimen. The developed numerical model includes the coupling effect between electromagnetic and thermal fields, and takes into account the non linear behaviour of the material properties. The study applies an enlightened experimentation method to build the feasible domain of the process and to achieve predictive empirical modeling. The ultimate goal is to replace the trial and error method that is usually used for the development of new parts, by costless experiments with the numerical model. Further development of this approach will lead to the computation of the residual stresses and finally to the assessment of the mechanical properties of the part. The end result will be the ability to shorten the development time and to improve the quality of the hardened part.

Jan 1, 2006

By B. Coupal, F. D'Hennezel

Sorption measurements show that peat moss has much stronger affinity for oil than straw, which is currently used. Microscopic studies of peat moss show a highly porous and fibrous material, and this property, associated with the phenomenon of selective absorption, had been used to absorb oil. Laboratory experiments show that peat moss absorbs up to eight times its weight of oil. Field tests have proved that peat moss can be an effective absorbent and can be used on a large scale.

Jan 1, 1972

By Farid Mirahadi

Forecasting productivity of construction operations is a difficult but crucial task in planning construction projects. Over the past decades, many models have been developed to forecast productivity for different construction operations. Models made up of several functional relations and controlled by a specific number of control rules are more in line with human reasoning and logic. Neural-Network-Driven Fuzzy Reasoning (NNDFR) structure as one of these models shows a great performance for modeling datasets among which clear clusters are recognizable. Lack of the compatibility of conventional NNDFR with fuzzy clustering algorithms besides the insufficient attention paid to the optimization of number of clusters in this model, created a potential area for further research. The main contribution of the proposed model is to develop a modified NNDFR system to model construction data. To this end, Fuzzy C-Means (FCM) algorithm is substituted for K-means in NNDFR structure, and its parameters such as the number of clusters and weighting exponent are optimized through genetic algorithm. The proposed model is further verified through simulation of a construction operation in which several qualitative and quantitative factors are considered. Its implementation to the case study shows a considerable improvement of model performance with lower Mean Squared Error (MSE). The developed model assists researchers and practitioners in utilizing historical construction data to forecast productivity of construction operations with a high accuracy that could not be obtained by traditional techniques.

Aug 1, 2013

By H. W. Fleming

In 1955, the results of a regional, geological interpretation of the northern portion of New Brunswick were used as a basis for selecting, for intensive exploration, three areas in which structural and stratigraphic conditions were believed to be favourable. Airborne electromagnetic work, in one of these areas, provided the justification for acquiring the Murray group. Even though the initial results were discouraging, this geological interpretation, combined with the fortuitous discovery of cop• per-bearing float, was sufficient reason for carrying out further work using geochemical methods. This work finally resulted in the discovery of the Murray massive-sulphide deposit, after about eighteen months of coordinated exploration on the property. While this deposit is a typical New Brunswick-type base-metal occurrence, extensive leaching has produced a fossil gossan that rendered it an elusive target for exploration techniques of limited penetration Full credit for localizing the target area is given to the geochemical techniques, but geophysical surveys were needed to provide the necessary

Jan 1, 1961

By Therese Schneck

The presence of xenon isotopes from in-situ spontaneous fission of short-lived Pu244 has been confirmed in Hadean detrital zircons from Western Australia. Hadean and meteoritic zircons can retain secondary overgrowths developed after primary cristalization at 3.97-3.94 Gyr. On the moon, the metal grain in sample 66095,78 is mantled by troilite, schreibersite and cohenite. High chlorine content FeCl2 is deposited around metallic FeNi. The magnitude of Pollonium-210 to Radon-222 on the Aristarchus plateau spectrum indicates a past greater activity. The Earth Moon system from Nb/Ta systematics is consistent with a Moon iron core delayed to 3,9 Gyr.

Aug 1, 2010

By Donald MacFadgen

Since 1950, a total of 164 miles of levels and rooms have been roof-bolted in the collieries of the Dominion Coal Company. Roof bolting is an efficient and economic method of sup-port where heavy timber sets or steel booms are necessary for temporary roof support, or where conventional methods of support interfere with the passage of mechanical mining equipment. This paper discusses present roof bolting practices and special bolting applications. THE practice of roof bolting in be collieries of the Dominion Coal Company dates from 1950, when preliminary studies and experiments were carried out in a mechanized room and pillar section of Dominion No. 20 Colliery. These studies were made in close liaison with members of the United States Bureau of Mines who were conducting similar studies. Following the successful application of roof bolting in No. 20 Colliery, this method of roof support was introduced into other collieries

Jan 1, 1963

By Yi-Chun Lin

Mechanical/Electrical/Piping (MEP) systems, due to their complexity and diversity, are the most intricate part of building construction. This being the case, Combined Services Drawings (CSD) and Structure, Electric and Mechanic(SEM) drawings can ensure that all coordination issues are resolved prior to construction. Construction companies attempt to apply Building Information Modeling (BIM) to manage and integrate engineering information and solutions efficiently into the CSD and SEM processes to enhance the accuracy of design and the efficiency of review. There are several powerful commercial tools, such as Bentley Navigator, Autodesk Navisworks, and Tekla BIMsight, that can review the integrated BIM model and detect conflicts in systems, and allow planners to correct the conflict issues one at a time. However, for increasing numbers of conflicts, this may be inefficient, and requires them to be arranged in a list according to impact and seriousness before solving them. For this reason, this research implements a module for conflict impact assessment based on rule-based reasoning to classify and weigh conflict impact and seriousness, and highlight the conflicted objects in the BIM system in different colors depending on their conflict type and seriousness during the analysis. This system not only detects and lists possible conflicts and errors, but also sorts them according to the severity of impact and conflict type. Planners can effectively modify the BIM models according to these conflicts as they are listed and visualized in the BIM system. If these conflicts, such as pipeline interference and problems of insufficient space, can be avoided in the early stages of planning, it facilitates the achievement of project objectives in quality, scheduling, and cost.

Aug 1, 2013

By M. Medraj, M. A. Arafin, D. P. Turner, P. Bocher

In this study, the kinetics of isothermal solidification during TLP bonding of Inconel 625 and 718 superalloys with nickel based multi-component filler alloy BNi-2 have been studied through a combination of direct experimentation and mathematical modeling in order to determine the effect of process variables and, thus, to optimize the process. The predicted isothermal solidification completion times from the boron diffusion model and migrating solid/liquid interface model were in good agreement with the experimentally determined values and, they were found to be significantly less than those of other nickel superalloys with different nickel based filler alloys. Further, significant reduction of holding time was observed with increasing bonding temperature and with decreasing joint gap. No significant grain growth in the base metals has been observed in the temperature range being investigated (1325 - 1394K).

Jan 1, 2006

By Qing-Xun Low

Ni current collector has excellent electronic conductivity and mechanica, properties. However, nicke, cannot be used in H2S-containing syngas SOFCs due to sulfur poisoning and coking. Copper coated nicke, is prepared by electrochemica, deposition. XRD, SEM, and EDX techniques are used to characterize the samples. After high temperature treatment in syngas containing, the coated samples exhibit high resistance of coke formation and sulfur corrosion compared to pure nickel. Therefore, copper coated nicke, is a promising anode current collector for H2S-containing syngas SOFCs.

Jan 1, 2010

By I. Demers

The abandoned Manitou mine site covers an area of approximately 190 ha near Val d?Or, Quebec. This old site has been generating acid mine drainage for several decades. In 2006, a partnership was established between the Quebec Ministry of Ressources Naturelles (MRN) and Agnico-Eagle Mines to reclaim the Manitou site using tailings from the nearby Goldex mine. These neutral tailings were to be deposited on top of the Manitou site. An extensive study was performed to evaluate specific reclamation scenarios to control acid mine drainage using Goldex tailings as cover material. The article first describes the global approach used for this evaluation, which includes in-situ hydrogeological monitoring, tailings characterization, laboratory column tests, and numerical modelling. Of the thirteen column tests, three were conducted to evaluate the parameters affecting the performance of covers made of Goldex tailings placed over the spillage area of the Manitou site. Geochemical and hydrogeological parameters were assessed during the leaching column tests for almost two years. The tests aimed at evaluating the effect of water table level and monolayer cover thickness on the overall performance. The testing procedure involved monthly leaching and measurement of geochemical parameters. Results indicate that water table position is the most important factor affecting the monolayer cover performance to control AMD. Based on these results, it was established that the water table must be located near the interface between the Goldex and Manitou tailings to effectively reduce AMD generation. Cover thickness also has an impact on cover performance, which is however less significant than the water table position. The testing scenario with a water table located at the interface with a one-meter Goldex tailings cover showed progressive improvement in effluent quality.

Aug 1, 2013

By N. Djilali

Many of the transport phenomena encountered in proton exchange membrane fuel cells occur intrinsically at the microscale level. Physically representative models that fully account for the salient physico-chemical and transport processes in PEM fuel cells are necessary to achieve truly predictive models that can be used with confidence to: (i) gain a better understanding of in-situ processes and couplings, (ii) explore new concepts, and (iii) support design and optimization. The development of more general, rationally based macroscale models requires use of knowledge on the microscale level to provide guidance, and to determine the required parameters and coefficients (model "constants"). In this paper we present a new membrane transport model, the binary friction membrane model (BFM2), recently developed to account for coupled protonic and water transport in polymer membranes. This general model is based on rational and physical consideration, removes several of the limitations of the empirical models used to date, and is formulated for all purfluoro-sulfonic acid membranes. The use of the BFM2 in a fuel cell model is illustrated highlighting significant performance predictions compared to existing empirical model. The second part of the paper addresses the fundamentals of two-phase transport in hydrophobic gad diffusion media. Computational and experimental visualizations resolving the microscale dynamics of water transport between the fibres of a GDL are presented, revealing transport mechanisms that are, contrary to assumptions used to date, dominated by fingering and channeling.

Jan 1, 2005

By S. A. Vazhnov, A. G. Kalimov, A. A. Potienko

In this paper we describe a mathematical model of the magnetic field and magnetohydrodynamic processes simulation in aluminum reduction cells developed in St. Petersburg State Polytechnic University, Russia. The model includes: (a) calculation of the currents in the busbar system and inside the aluminum cell construction elements including cathode and anode structures, aluminum and electrolyte layers; (b) magnetic field simulation using the integral equation method; ( c) investigation of the magnetohydrodynamic characteristics on the basis of a shallow-water approach. The developed model was used to investigate operational characteristics of the different industrial aluminum cells. Calculated magnetic field distributions and MHD stability parameters were compared with the available experimental information; the comparison demonstrated a reasonably good agreement.

Jan 1, 2006

By E. A. Hart, J. E. Gill

"The property of Arntfield Mining Corporation, formerly Arntfield Gold Mines, Limited, covers an area of 2,110 acres and lies in Beauchastel township, western Quebec. The Francoeur mine lies to the west, and to the east are the West Wasa and Wasa Lake properties.The property was staked in September, 1923, by the late F. S. Arntfield. The early surface work was concentrated in the west part of the property along the Francoeur-Arntfield shear zone. The zone was opened by No. 1 shaft, which was sunk for an inclined depth of 250 feet. A series of silicified lenses were discovered farther east, where No. 2 shaft was later raised to the surface. A third shaft explored a shear zone about 1,900 feet to the east, where No. 3 shaft orebodies were developed.The mill was built at No. 3 shaft and production commenced in July, 1935, at 125 tons a day. This was increased to 280 tons by 1938, and later to 350 tons. The mine continued operations on this scale until April, 1942, when the exigencies of war necessitated closing. The Company was reorganized in 1944 and underground development was resumed in June, 1945. The total value of gold and silver produced to April, 1942, was $2,011, 755 from 529,987 tons of ore.ROCK TYPESThe area is underlain by highly deformed and altered Keewatin volcanics overlain by little deformed Cobalt sediments along the south boundary. The lavas in the vicinity of the mine workings are rhyolite, trachyte, andesite, and a flow breccia of intermediate composition. The fragmentals range from fine, well-bedded tuffs to coarse agglomerate in which acidic and basic horizons can be distinguished.The intrusive rocks are diorite and quartz-feldspar porphyry in the form of stock and sills, and narrow dykes of mica lamprophyre and syenite porphyry."

Jan 1, 1954

By E. Brouillette

Difficult operating and mining conditions such as low visibility, difficult roadbeds, fast cycling, small openings, and sharp corners create high demand for LHD manoeuvrability and operator dexterity. Operator experience and patience is especially solicited to fill the bucket rapidly and efficiently and performance can be particularly affected by the skill level of individual operators. Teleoperation and automated loading are viewed as options to improve overall equipment and operation performance in certain mining conditions. Comparative statistical measurements of autoloading performance in different production environments at Noranda demonstrate an increase in bucket filling efficiency and a reduction in filling variance, allowing LHD operation to be more consistent and within manufacturer specifications. Consequential cost savings and productivity increases are demonstrated to be transferable to other mining situations.

May 1, 2003

By O. Lashkari

Swirled Enthalpy Equilibration Device (SEED) is a new patented Slurry-on-Demand, SoD, processing route. The semi-solid slug preparation is carried out by off-center swirling of aluminum melt in a metallic mould. As part of the current research program on the semi¬solid processing of aluminum alloys, the morphological evolution of 356 aluminum foundry alloy microstructure is reported here. Semi-solid slugs were prepared using two different pouring temperatures of 645°C and 695°C respectively. Morphological evolution of the semi-solid microstructure was characterized using image analysis through measuring of primary a-Al particle size, number density, aspect ratio and sphericity. The possible relationships between microstructural features and process parameters were also investigated. The current report covers the effect of pouring temperature on the morphology of primary a-Al dendrites and attempts are made to explain the differences between the predicted percentage primary a-Al phase and those of the actual values in the as-cast slugs.

Jan 1, 2004

By M. Sugamata

Creep tests were carried out for friction welded joints of AZ31 magnesium alloy rods under an ambient atmosphere at temperatures between 423 and 573K. Tensile tests were also performed at temperature from room to 573K. The obtained results were compared with those of the base metal. AZ31 extruded rods of 19 mm in diameter were joined by brake type friction welding machine. Creep and tensile specimens were machined out of the welded rods. The tensile strength of the joints was almost the same as that of the base metal at room temperature. However, joint efficiencies of welded joints were about 92% at above 373K. The elongation of welded joints was lower than those of base metal. The welded joints showed appreciably higher minimum creep rate and shorter rupture time than the base metal at all the tested temperatures and initial creep stresses. Creep and tensile rupture of the joints always occurred at near the weld interface. Thus, friction welded joints of AZ31 alloy showed lower creep and tensile strength than the base metal at elevated temperature.

Jan 1, 2006

By J. Salazar

This paper presents a dynamic simulator of the semi-autogenous grinding operation deduced from first principles (non-stationary population balances) coupled to a Model-Based Real-Time Optimization (MBRTO) system to study optimizing strategies for an industrial semi-autogenous mill using genetic algorithms. For the design of the MBRTO both a validated first-principle steady-state model adapted on-line and a dynamic model were used to study the transient effect. The objective function considered is to maximize the ore throughput or the fine-product rate by changing the power-draw. For these purposes, these two performance indexes were introduced as fitness functions in the genetic algorithms. The three decision variables used were the ore feed rate, the water feed rate and the mill rotating velocity. The optimization problem was solved using a classical genetic algorithm with constant population. Constraints in the power draw and the filling level were handled by assigning a penalty function to the fitness function. Simulation results using industrial data for a large 1800 t/h copper-ore mill show the effectiveness of the system in finding the optimum controller set-points as a function of the process-operating constraints; mainly maximum ore feed rate, power draw and filling level. Starting from non- optimum conditions, the optimizer is able to improve the global performance index by 50% relative to a base case.

Jan 1, 2007