Search Documents

By P. Amelunxen, E. Herrera, L. Hill, J. Vanderbeek

It is well-known that the particle breakage mode that occurs in a semi-autogenous mill is significantly different from that which occurs in a ball mill, enough so to warrant very different lab scale breakage tests and scale-up models. This phenomenon, at the plant scale, leads to changing process constraints depending on the particular properties of the ore. For example, hard or coarse ores might bottleneck the SAG/AG mill throughput, while the ball mills might constrain throughput when milling soft or fine ores. Because the power draw of a ball mill is fairly constant compared to that of a SAG/AG mill, periods of SAG/AG mill bottlenecks lead to increased ball mill circuit specific energy consumption and a finer grinding circuit product size, which together constitute a loss of efficiency of the overall process. Because HPGR circuit throughput is less sensitive to changes in ore hardness, this situation is less common or severe in those circuits. Furthermore, the ball mills are somewhat decoupled from the upstream crushing circuits through the use of surge bins, which also helps to mitigate this effect. As a result, ore hardness variability constitutes a significant cost penalty that should be applied to SAG mill/ball mill/pebble crusher SABC circuits when evaluating the relative economics of different grinding circuit configurations. Nevertheless, the issue is by-and-large ignored, because most current HPGR trade-off studies are based on averaged ore hardness parameters. This paper provides an estimate of the magnitude of this penalty for a typical operation by using Monte Carlo simulation methods and plant data from Freeport-McMoRan’s autogenous, semi-autogenous, and HPGR-based comminution circuits. A case study from an in-house 96K t/d sulphide project is presented to illustrate the concept. It was found that by including variability effects, the trade-off NPV of the HPGR circuit over that of the SAG mill circuit increases to $84 million from negative $33 million, effectively reversing the original decision of selecting a SAG mill circuit for the fixed hardness case.

Jan 1, 2012

By Miguel A. Cuba

Resource models are generally constructed using data of different types and/or from different sources. A common issue is the consistency of scale in the information that often leads to a requirement to composite the data prior to model construction. For the purposes of mine planning, development and/or resource assessment, this model may then be upscaled to a relevant selective mining unit. It is well established that the geostatistical parameters for resource model construction is scale dependent. In particular, the volume variance of integrating these various scales has a direct impact on the variogram that should be used in model construction and/or the assessment of volume variance relations as it affects resource estimation. The scaling laws are a set of guidelines that detail how the variogram should change as a result of a change in the volume; these laws are empirically derived and involve some simplifying assumptions, not the least of which is an assumption of shape invariance in the variogram structure. An alternative approach was proposed to directly upscale the variogram via numerical integration, which demonstrates that the assumption of shape invariance is not required and we can directly access the new variogram shape given any volume of interest. This paper compares these two different approaches to variogram upscaling by considering two applications: the first corresponds to a 2D synthetic case and the second looks at a 3D case with data from a porphyry copper deposit. The simulation studies in these cases show that the direct upscaling approach performs better than the scaling laws in fitting the average experimental variogram values at any block size. This is based on a mean absolute error criterion. Moreover, it is also shown that with an increase in the block size, direct variogram upscaling significantly outperforms the scaling laws approach.

Oct 1, 2009

By M. Roy, Y. Roux, R. McIvor

"La Compagnie Minière Québec Cartier at Port Cartier. Quebec, utilizes six parallel wet grinding open circuit ball mills to grind iron ore concentrate for the pellet making process. In an attempt to improve grinding efficiency, a mix of 605 25 mm (1 in.) and 405 38 mm (1 ½ in.) grinding balls was charged to mill D while the opposite mix was used in all the other mills. Because media costs were higher for mill D, it was necessary to find out if the smaller balls provided a net economic benefit. Therefore, a test program was undertaken to determine the relative efficiency of the charge in mill D compared to the other grinding mills. Mill F was chosen for comparative efficiency measurements.The first problem was to choose a suitable definition of grinding efficiency. In management's view, previous attempts to quantify milling performance using population balance modelling were ineffective because they were unable to relate breakage rate functions to grinding circuit economical in any meaningful way. Work index analysis was also not favoured because of a number of complicating effects, including the fineness of the feed and product streams and open circuit grinding.It was decided to adopt a recent innovative approach which had been successfully applied to closed-circuit ball milling. For ""functional performance analysis of ball milling"" (McIvor et al., 1990; McIvor et al., 1991), a size criterion is first chosen to define ""fines·' and ~'coarse particles"". In this case 45 microns (325 mesh) was chosen to distinguish fines from coarse material. The relative grinding efficiency of each ball mill environment would then be ~e cumulative grinding (disappearance) rate of coarse (plus 45 nucrons) material per kilowatt hour of energy applied to the coarse material in the mill, divided by the grindability (measured in the laboratory) of the coarse material in the mill feed.Because the disappearance rate of coarse particles is also the production rate of fines, the following equation can be written for the efficiency of the mill environment, Effe, as defined above:"

Jan 1, 1994

By Sammy Bansah, Komla Dzigbodi-Adjimah

Abstract-Ghana, a major West African gold-producing country, took a crucial step in 1986 to allow private participation in mining ventures that had hitherto been state controlled and starved of funds. This decision has led to a three-fold rise in gold production with substantial local and foreign capital once again flowing into exploration and mining projects. Though the rise in gold export is due primarily to increased production from large mines such as Ashanti Goldfields Corporation, Billiton Bogosu Gold, Tebrebie Goldfields and Ghana Australia Gold that work primary lode gold deposits on quartz veins and Banket conglomerates, a fair amount of gold comes from placer gold mining from which two new mines have been developed at Kwabeng and Bonte during the current gold boom. Also, placer gold mining is important locally because the lower capital outlay required for its development enables many entrepreneurs to operate small concessions and provide employment for a large pool of unskilled labor. Placer gold exploration and development in Ghana is labor-intensive. Pitting is the most used method although few employ the mechanized ("Banka") drilling. The advantages and disadvantages of the two approaches in the local setting are discussed. The gravel is normally sluiced and the gold recovered by amalgamation. The drawbacks to successful placer gold exploration in Ghana have been attributed to lapses in execution of exploration programs (Dzigbodi- Adjimah and Arhin, 1993; Dzigbodi-Adjimah and Gawu, 1994). However, the failure to recognize and set time frameworks and financial limitations for the various stages of placer gold exploration have spelt the doom of some projects. It is critical that the characteristics of the placer gold deposit be determined by efficient and cost effective means. A planned exploration supported by adequate flow of funds saves costs and leads to success. This article discusses the current Ghanaian situation and presents proposals from case studies for planning and budgeting placer gold exploration programs for use in similar settings.

Jan 1, 1995

By E. J. Marcotte

"BRIEF DESCRIPTION OF GRINDING CIRCUITCrushed ore at -5/ 16 in. is delivered by a conveyor system from the crushing plant to two 1250 ton fine ore bins. The ore is transferred from each bin by a 30 in. feeder conveyor belt, operated by a Link Belt P.I. V. (variable speed) drive, to a 24 in. conveyor that feeds the 8 x 10 Allis Chalmers rod mill.The rod mill discharges to a common mill discharge pump box. Three 6 x 6 SRL pumps are employed to pump the combined mill discharge pulp to a common distributor box which distributes the feed to two of the three Kreb D lSB cyclones in each of the two banks at a hydraulic pressure of 6 psi.The cyclone overflow at a specific gravity of 1. 25 (i.e. 32% solids) is transferred by gravity to two revolving chip screens for wood chip removal and from there to a pump box. Two 5 x 5 SRL pumps feed the pulp to the thickeners. The underflow from the cyclones is fed to two 8 x 8 Allis Chalmers ball mills which discharge to the common mill discharge pump box. Thus, a closed circuit is formed between the ball mills and their respective bank of cyclones. The circulating load as most recently calculated is 262%."

Jan 1, 1966

By D. Embury

The construction and utilization of oil and gas pipelines is a vital aspect of the Canadian economy. The evolution of materials for this application can be considered as part of an evolutionary process in which the processing of the materials is linked to the design requirements of the pipeline. The evolution of both materials and designs will be considered in terms of parameters such as yield strength, work hardening characteristics including strain path changes such as the Bauschinger Effect and toughness. The final portion of the presentation will consider the possible uses of non-metallic materials, composites and 'smart 'systems in pipeline construction.

Jan 1, 2005

By R. A. D. Pattrick, D. A. Polya, D. J. Marsh, J. -J. Bao

"The utility of high-density stream sediment and stream water sampling to the exploration for silver deposits was investigated by the study of the epithermal Ag-Au base-metal prospect at Lagalochan in western Scotland. The geology of Lagalochan is dominated by a calc-alkaline Caledonian intrusive complex emplaced into Dalradian Supergroup rocks (Harris et al., 1988a). The complex consists of subvolcanic porphyrytic rocks associated with intense hydrothermal alteration and brecciation. Early Cu-Ag-Mo-rich mineralization is found in the core of the complex with later Pb-Zn-Ag-Au-As-Sb-rich mineralization toward the margins (op. cit.).Stream sediment sample analysis spatially resolved the Cu-rich and Ag-rich mineralization. Ag and Cu anomalies relative to local background values were found in all size fractions analyzed (-125µm, +125 µm, +180 µm, +250 µm) but the more pronounced anomalies were found in the -125 µm fraction. The coarser fractions generally revealed more erratic but longer dispersion trails. The separation of Cu-rich and Ag-rich mineralization is also apparent in the distribution of relatively high dissolved Cu and Ag in stream waters, particular when expressed relative to the solute load as Cu/TDS and Ag/TDS.The mineralization at Lagalochan is indicated by Ag, Cu and Pb stream sediment and water concentrations that are anomalous with respect to local backgrounds, but are difficult to distinguish from regional backgrounds. This emphasizes the further potential of high-density stream water sampling,in particular, as a viable geochemical exploration tool on a sub-regional scale for epithermal depositsin relatively unpolluted upland terranes."

Jan 1, 1995

By A. L. Hinde, H. Dong, J. T. Kalala

"The High Pressure Grinding Roll (HPGR) is gaining acceptance in the mineral processing industry and has become a competitive technology in reducing the specific energy consumption in Mineral processing plants. The amount of samples required for HPGR amenability testwork and HPGR wear tests is usually high and often cannot be available at early stage of projects were only a few drill cores are available.Although HPGR was initiated from small scale piston die compression tests, the development of small scale piston die test to predict the performance of HPGR has been slow.The objectives of this paper was to present the designs, operating procedure of piston-die press and operating conditions which have resulted in similar particle size distribution obtained from a piston die test and HPGR Labwal unit starting from the same feed size distribution. Testwork were conducted using a 2 MN piston-die press and a Labwal HPGR unit on major South African ore types, viz, gold, platinum and iron ores. The results obtained show that piston-die test can generate data to predict energy consumption, product size distribution, and even to evaluate the edge effect."

Jan 1, 2012

By Sammy Bansah, Komla Dzigbodi-Adjimah

Ghana, a major West African gold-producing country, took a crucial step in 1986 to allow private participation in mining ventures that had hitherto been state controlled and starved of funds. This decision has led to a three-fold rise in gold production with substantial local and foreign capital once again flowing into exploration and mining projects. Though the rise in gold export is due primarily to increased production from large mines such as Ashanti Goldfields Corporation, Billiton Bogosu Gold, Tebrebie Goldfields and Ghana Australia Gold that work primary lode gold deposits on quartz veins and Banket conglomerates, a fair amount of gold comes from placer gold mining from which two new mines have been developed at Kwabeng and Bonte during the current gold boom. Also, placer gold mining is important locally because the lower capital outlay required for its development enables many entrepreneurs to operate small concessions and provide employment for a large pool of unskilled labor. Placer gold exploration and development in Ghana is labor-intensive. Pitting is the most used method although few employ the mechanized (“Banka”) drilling. The advantages and disadvantages of the two approaches in the local setting are discussed. The gravel is normally sluiced and the gold recovered by amalgamation. The drawbacks to successful placer gold exploration in Ghana have been attributed to lapses in execution of exploration programs (Dzigbodi-Adjimah and Arhin, 1993; Dzigbodi-Adjimah and Gawu, 1994). However, the failure to recognize and set time frameworks and financial limitations for the various stages of placer gold exploration have spelt the doom of some projects. It is critical that the characteristics of the placer gold deposit be determined by efficient and cost effective means. A planned exploration supported by adequate flow of funds saves costs and leads to success. This article discusses the current Ghanaian situation and presents proposals from case studies for planning and budgeting placer gold exploration pro-grams for use in similar settings.

Jan 1, 1995

By A. Farzanegan, D. A. Lowther, A. R. Laplante

"Off-line optimization studies are often necessary to improve the efficiency of grinding circuits. These studies are primarily based on the mathematical modelling of processing units (e.g., ball mills and hydrocyclones) and computer simulations. To complete an optimization task, process engineers must possess skills and knowledge of different subtasks involved in such efforts, e.g., plant audit, laboratory tests, and data analysis. Such know-how can be in part provided by Knowledge-Based Systems (KBSs). One such system, being developed in C Language Integrated Production System (CLIPS), is presented here, with focus on the estimation of ball mill selection functions for the purpose of both diagnostic and simulation, and its use for the optimization of ball size. Some of the interpretation and diagnostic rules will be presented, as well as grinding kinetics and classification data likely to fire them.IntroductionSince the late eighties there has been a growing trend in applying Knowledge-Based Systems (KBSs) to mineral processing [Meech 1990, Bearman and Milne 1992). Table l lists some KBS (often referred to as expert systems) applications that have been used mainly as tools for improving on-line monitoring and control of grinding circuits. However, there has been fewer attempts to add the symbolic processing powers of KBSs to conventional off-line grinding simulators. Figure 1 shows a relatively standard procedure to perform an off-line optimization study [Napier-Munn and Lynch 1992]. In brief, a typical program includes taking representative samples from a number of streams, running laboratory tests on collected samples, estimating model parameters which describe physical processing units (e.g. ball mills and hydrocyclones) validating model predictions and using models for simulation trials. One inevitably needs to be familiar with concepts of process modelling and simulation as well as various computer programs to be able to complete all steps of the study. Much of this ""expertise"" can be captured by KBSs, given their inherent capabilities for symbolic knowledge representation and manipulation."

Jan 1, 1997

By J. C. O'Rourke

"Gibraltar Mines Ltd. has been operating its open pit copper mine for fifteen years. In that time over 140 million tons of waste and low grade material has been placed on the mine waste dumps. Laboratory and in-situ testing indicated that enough leachable copper was recoverable from the dumps to justify a leaching operation which would include the construction of a solvent extraction-electrowinning plant. The plant, which was commissioned in October, 1984 was designed to process 3,000 usgpm of dilute copper solution to produce 5,000 tons per year of high quality cathode copper.This paper deals with the start up and initial year of operation of Gibraltar's SX-EW plant. The three areas: leaching solvent extraction and electrowinning are presented with emphasis on the innovations which were made to help overcome the problems unique to die Gibraltar operation.THE LEACHING CIRCUITThe mines waste dumps are leached to produce a pregnant copper solution as feed to the SX-EW plant. To achieve this the dumps are sprinkled with a mildly acidic solution which percolates through the dump. In travelling through the dumps the solution contacts the surfaces of the liberated copper minerals and disolves the soluble copper into the form of copper sulphate. The leaching reaction is achieved by a combination of bacterial action to oxidize the suphides and solublization of the copper into the acid solution.For the bacterial action to occur the dumps must be at or near the ideal pH of 1.9 - 2.1 and the necessary elements of the reaction must be present. Because a bacterial reaction is involved there is a lag time between the time when the conditions for bacterial growth are achieved and when the bacteria are in their active growth phase. Laboratory tests with Gibraltar ore indicated that bacterial action takes two to three months to reach its maximum rate. See figure 1.The expected lag time for the planned rate of bacterial leaching prompted Gibraltar to start irrigating the dumps in late June 1986 for a plant start up in early fall. The lag time proved to be longer than expected and the dumps took until November to start producing copper at the expected rate. See figure 2."

Jan 1, 1988

By Rodney G. Orr, Phil Robertshaw, Roland Loewer, Klau Lehnert-Thiel

This paper documents the 1988 discovery and subsequent evaluation (to 1991) of diamond bearing kimberlites in the Fort à la Corne area, Saskatchewan, by Uranerz Exploration and Mining Limited. Cameco Corporation began participating as a joint venture partner (50%) in mid-1989. The first indications that kimberlite-type intrusions might exist in the area carne from Geological Survey of Canada aeromagnetic maps. Because of the overburden thickness (over 100 m), magnetometer surveys continue to be the main exploration tool in defining pipe locations and sizes. Magnetometer surveys in varying levels of detail have outlined one main cluster and two sub-clusters, the main group being some 10 km by 50 km in size. In excess of 70 individual targets have been interpreted from the magnetics as probably representing kimberlites. The size range of the individual magnetically-defined bodies is between 1 ha and 74 ha. Proof that the magnetic anomalies were kimberlite intrusions carne in 1989 when each of seven test holes, all drilled on different targets, intersected the potential diamond host rock. The majority of the targets tested were diamond-bearing, with the indicator mineral chemistries suggesting that both peridotitic and ecIogitic diamond parageneses could be expected. To date, 18 individual kimberlite bodies have been drill-tested. A total of 39 bulk samples, amounting to 186 t (representing 360 t of theoretical sample recoveries) were processed in 1990 and 1991. One hundred and sixty diamonds were recovered, averaging 0.04 carats in weight, the largest being 0.6 carats. Most of the bulk sample grades are less than 2 carats/loo t; only three bulk samples have higher grades, the best being approximately 10.5 carats/l00 1. The diamonds are predominantly gem-quality stones.

Jan 1, 1992

By A. B. Isaeva, A. Yu. Lein, A. A. Karpenko, V. V. Serova, A. P. Lisitzin, V. Yu. Rusakov, V. N. Lukashin

Abstract - The flux of sediment matter was determined using sediment traps near a black smoker ("Saracen’s Head," Broken Spur hydrothermal field) and the mineral and chemical compositions of the settled matter were examined. The metallic minerals are represented by Fe sulfides (pyrite and pyrrhotite), and Cu and Zn sulfides are also found in small and equal quantities. The hydrothermal suspended matter contains abiogenic calcite in amounts comparable to that in Ca sulfates. The content of silica and, specifically, of amorphous Si is unusually low. Such correlations between chemical elements and minerals, together with the isotopic compositions of S and C, are characteristic of a relatively young and active stage in the evolution of a hydrothermal system. Sediment traps within and under neutrally buoyant hydrothermal plumes collected biogenic material in addition to hydrothermal components. Microbial chemosynthetic production of organic carbon near the hydrothermal vent is comparable to primary production in the euphotic layer. Fe, Zn, Ca, Si, Ba and P are enriched in particulate matter in comparison to the background. A vast compound plume containing the discharge of multiple hydrothermal vents was found to the south of the Broken Spur hydrothermal field.

Jan 1, 1999

By Ken McClure, Alex Day

Located North of Williams Lake British Columbia, Gibraltar Mine is the fourth largest open pit Copper mine in North America. Gibraltar commenced Copper concentrate production in 1972 with a mill throughput rate of 30,000 tons per day. A series of expansion projects, including installation of a second SAG mill with variable speed drives in 2013, has increased mill throughput to 85,000 tons per day. Over the past 24 months, Gibraltar Mine in partnership with Spartan Controls has executed several advanced process control programming projects culminating in the implementation of a Continuous Speed Controller (CSC) for the most recently installed SAG mill. This paper covers development and results for the SAG mill speed controller. INTRODUCTION In January 2016, the price of Copper fell below $2.00 USD per pound, the lowest price in 7 years. Gibraltar Mine faced a significant challenge; how to maximize profit in an environment where capital spending was not an option. An opportunity was quickly identified to improve performance through increased automation and advanced control of the grinding processes. Beginning in March 2016, Gibraltar Mine partnered with Spartan Controls to introduce Advanced Process Control (APC) to the grinding circuits. The collaboration between metallurgical and process control engineering disciplines proved to be effective for achieving gains in throughput, reliability and productivity for the mill process. The Gibraltar milling facilities include 2 grinding-flotation plants for concentration of chalcopyrite ore with throughput rates of 58,000 tons per day (Concentrator 1) and 38,000 tons per day (Concentrator 2). Each of the two concentrators has a 34’ diameter SAG mill powered by 2 GE 4800 kW synchronous electric motors. For SAG 1 (in concentrator 1), power is transmitted through 2 Eaton Airflex clutches. For SAG 2 (in concentrator 2), the motors are driven by 2 TMEIC Variable Frequency Drives (VFDs). All programming is done using DeltaV, which Gibraltar uses as its Distributed Control System (DCS) and Human Machine Interface (HMI).

Jan 1, 2019

By P. Chu, J. A. Finch, R. Li

"Bubble size plays a key role in flotation. In this paper, we examine the possibility of using passive acoustic sending to determine bubble size. Software was developed based on Short Time Fourier Transformation (STFT) to analyze the frequency of the acoustic signal emitted from the bubble formation event. Bubble size was determined from the Minnaert frequency. The acoustic-determined bubble size responded to reagent dosage, but was less sensitive than that given by imaging. The constraints of the current acoustic approach are discussed.INTRODUCTIONBubble size is an important factor affecting flotation performance. It determines the maximum available surface area for collecting and transporting mineral particles. Of interest for process control (Gorain, Franzidis, & Manlapig, 1995), it can be determined by several techniques, such as image analysis (Grau & Heiskanen, 2002; Hernandez-Aguilar, Gomez, & Finch, 2002); conductivity (Barigou & Greaves, 1992); drift flux analysis using gas rate and gas holdup measurements (Banisi & Finch, 1994); and optical sensors (Randall, Goodall, Fairlamb, Dold, & Connor, 1989). However, all these techniques have drawbacks.Acoustic analysis of the oscillatory behaviour of bubbles to extract bubble size is another possibility (Leighton & Walton, 1987; Pandit, Varley, Thorpe, & Davidson, 1992; Al-Masry, Ali, & Aqeel, 2005; Manasseh & Ooi, 2009; Leighton & White, 2012; Spencer et al., 2012). The fundamental basis is the work of Minnaert (1933) who first correlated the bubble size with its natural frequency, Equation 1:"

Jan 1, 2016

By Brian O'Hearn, Doug Hanson

"The most commonly used tendon supports in the Sudbury area include rock bolts, rebars, friction anchors and cable bolts. Due to the fact that these tendons are physically different and employ different anchoring systems they offer varying degrees of stiffness, yield ability, load capacity, anchor dependability and energy absorption. These differences coupled with variable rock mass and changing stress conditions have made it challenging to engineer the design of an effective support system. By tapping into the knowledge and experience gained by ground control practitioners, an empirically based rating system has been assembled that offers a guide to designers of support systems when choosing the most effective tendon support over a range of rock mass and stress conditions.A methodology referred to as support planning can be used to design support systems whose rehabilitation costs will be minimized. The use of multiple tendon types in anyone support layout is advocated, particularly when the stress state of the rock mass to be supported is expected to undergo a change."

Jan 1, 1995

By Laxman M. Amaratunga, Glen G. Hein

"Most mining operations utilize the tailings coarse fraction for backfilling while the fines have been traditionally disposed on surface in tailings ponds. Recently, paste fill has been developed which uses a fraction of the fine tailings (10-30% w/w of <45 µm) in the fill (Brummer and Moss, 1991). This development allows a mining company to use a portion of the fines for backfill, but still requires surface impoundment of the unused tailings. Reactive tailings have the added problem of generating acid after being oxidized in the presence of air and water. Treating acid mine drainage (AMO) from these ponds has proven to be a costly environmental problem and a long term liability.One practical method to reduce the environmental impacts associated with the tailings pond is to modify the physical and chemical prope1ties of the fine tailings so that they can be utilized in an environmentally safe manner. This was accomplished by agglomerating the tailings into pellets and using theses pellets as a coarse aggregate in a total tailings paste fill. This technology does not require any supplemental sand or gravel to be added to the fill.This paper presents the ongoing research into utilizing these tailings agglomerates as a coarse aggregate fraction, in order to create a total tailings paste fill which has supe1ior strength characteristics.IntroductionThe Canadian mining industry produces more than 500 million tonnes of tailings and waste rock annually. The waste rock is usually returned underground for use as rock fill in underground support with the tailings remaining to be disposed of in tailings ponds. Tailings consist of a coarse and fine fraction, and can be either reactive (acid generating) or non-reactive. In an effort to minimize tailings disposal, the coarse fraction has been used underground in backfill along with alluvial sands. This diversion of the coarse fraction, however still requires that the fine fraction be disposed of in tailings ponds. This disposal creates the potential for acid mine drainage (AMO), since in the presence of air and water, reactive sulphide tailings can generate acid. It is therefore an important goal in the mining industry to minimize the disposal of fine tailings into tailings ponds since the treatment of AMO is a costly and long-te1m environmental liability."

Jan 1, 1997

By Rick Steen, Weldon Read, Morrism Tracy T.

Edging for starter sheet blanks used in conventional copper refineries has always been problematic for getting the edging to seal and adhere to the titanium material used for the blank so that copper is prevented from plating under the edging and cause undo problems in getting the copper sheets to separate from the blanks. A method was developed at the Amarillo Copper Refinery utilizing an injection molding process that better adheres the edging material to the titanium that makes the harvesting of starter sheets much easier to the point that robots are now used to strip with and which holds up very well to the unforgiving physical nature of the electroplating process. It is believed that this technology could be successfully utilized for permanent cathodes as well. INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting and Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co- products (Marcosson, 1949). Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills and two solvent extraction-electrowinning (SX-EW) plants all in Arizona plus a copper smelter in Arizona and a copper refinery in Texas. Figure 1 illustrates how the copper metal comes out of the ground at the mine and ends up as a refined product at the refinery. The copper refinery in Texas is known as the Amarillo Copper Refinery (ACR) and is located in Amarillo, Texas. It was built in 1975 to replace 3 other aging refineries and was designed to produce 550,000 tons (500,000 MT) of refined copper per year using conventional starter sheet technology. At the time it was commissioned it was the largest tankhouse in the world at just under 1/2 miles long under one roof.

Jan 1, 2019

By Caitlyn J. McKinley, Ahmad Ghahreman, Maziar E. Sauber

Ever-growing global needs for critical metals, such as rare earth elements (REE), and base metals, such as copper and nickel, and their environmental impact motivated the pursuit of sustainable flowsheets. Regeneration of hydrochloric acid in chloride-based leaching flowsheets as a critical unit operation is an example of such endeavours. This study presents an efficient hydrochloric acid regeneration method from a magnesium chloride solution waste by addition of sulphuric acid in relatively low temperatures. The effects of temperature, initial magnesium chloride concentration, amount of sulphuric acid added, and airflow are examined. Experimental work are focused on temperatures between 80 and 95°C, initial magnesium chloride concentrations of 2 to 5 M, 100% to 220% stoichiometric sulphuric acid additions, and airflows between 200 to 600 mL/min. The developed technology recovers hydrochloric acid at a high rate and concentration with a relatively small environmental footprint. INTRODUCTION The mining and metals sector is under increasing environmental and economic pressure to make more efficient use of chemical reagents and energy in the production process. This affects several areas of process and flowsheet design such as the selection of the most appropriate unit operations and the overall design of the process steps paying heed to sustainability. Owing to the inherent inefficiencies of physical and chemical processes used in the mining industry, there will be materials and streams generated that are not a desirable part of the envisaged flowsheet. Thus, methods are implemented to recover and recycle such effluents. If the recovery and recycling are not economical, then procedures are followed to neutralize and dispose these effluents. In many cases, these effluents are potential contaminants or hazardous materials, and their disposal should be looked at in a much larger context. The safe management of the contaminants and hazardous effluents is a daunting problem in the mining industry and is fraught with technological, economic, social, and political challenges.

Jan 1, 2019

Grinding with an electrochemically inert grinding media (i.e. high chrome white iron, or Magotteaux’s Duromax® alloys) shifts the pulp potentials to more oxidising conditions, increases the dissolved oxygen content and reduces the EDTA extractable iron concentration when compared with milling with electrochemically active grinding media (forged steel). These changes in pulp chemistry produce cleaner particle surfaces, reduce reagent consumption and increase concentrate grades and recoveries. This paper presents a robust laboratory test program that is able to not only demonstrates these effects but also provide an indication of the magnitude of the improvements that are possible. While laboratory studies are interesting, the proof is in the pudding! So, the paper provides an overview of plant trials conducted at a number of operations around the world, including: Newcrest’s Cadia Operation, Oz Minerals’ Prominent Hill Mine and Glencore’s Ernest Henry Mine. These successful plant trials clearly demonstrate that selection of the right grinding media alloy will yield savings in grinding media consumption and reagent consumption as well as increases in revenue through improved copper, gold and molybdenum recoveries. INTRODUCTION The key to a successful separation in mineral processing is the preparation of particles with adequate liberation under the correct pulp chemical conditions. While the importance of liberation on flotation separations is generally understood and well documented in the literature (Johnson, 1987; Jackson, Sutherland, Gottlieb & Quittner, 1989; Young, Pease, Johnson, & Munro, 1997; Greet and Freeman, 2000), the importance of pulp chemistry is more nebulous, particularly with regard to the impact of grinding media. Extensive work examining the electrochemical interactions between grinding media and sulphide minerals has been completed (for example, Iwasaki, Reid, Lex & Smith, 1983; Natarajan and Iwasaki, 1984; Yelloji Rao and Natarajan, 1989(a); Yelloji Rao and Natarajan, 1989(b)). Broadly, these studies indicate that most sulphide minerals are more noble than the grinding media used during comminution, therefore a galvanic couple between the media and the sulphide mineral(s) exists, which increases the corrosion rate of the grinding media. The corrosion products of the grinding media, iron oxy-hydroxide species, invariably precipitate on to the surfaces of the sulphide minerals thereby affecting their floatability (Johnson, 2002).

Jan 1, 2019