Search Documents

By Slavoljub D. Maksimovic

At some coal mines, methane gas is released during raise drilling. At the request of the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, the Bureau of Mines conducted ventilation surveys at different raise drill sites to assess various methods of reducing methane concentration. The resulting data indicate that raise drill shaft cavities are ventilated by air compressors, vacuum pumps, auxiliary blower fans, and free intake air from the surface. The compressors, pumps, and fans operate simultaneously or separately. At the bottom of the shaft cavities, ventilation is controlled by regulators and airlocks. Methane is monitored, measured, and periodically sampled on the surface, at the bottom, and at different levels in the shaft cavities. Maximum concentration of 3.5 percent was measured in one shaft in West Virginia. Air velocity down the raise drill shafts is always very low, Maximum recorded air down the drill stem was 3,000 cfm, which can be increased by adding air compressors. The best way to ventilate shaft cavities is through the simultaneous use of air compressors and vacuum pumps. If the methane concentration cannot be reduced with additional compressors, then the inside diameter of the drill rod should be increased, or larger pilot hole drill bits should be used.

Jan 1, 1981

By L. C. IlsLey

[The last previous Bureau of Mines publication relative to details of permissible methane detectors (Bulletin 331, published in 1930) describes detectors of four different types, namely flame, combustion, catalytic, and a combination Wheatstone-bridge axed catalytic type in which catalytic action at the surface of a platinum filament when in methane causes a change in the temperature and resistance of the filament, thus unbalancing the bridge circuit and giving a reading proportional to the methane concentration. Three detectors of the latter type have been approved since 1933. A brief description of each follows: U. C. C. Detector Approved No. 902, covering the U. C. C. indicating detector, as described in Bulletin 331, was entered January 27, 1330, to cover important chances in design that permit checking; the calibration of the detector at any time, whether in gas or fresh air. Essential features of the detector are shown in figure 1.]

Jan 1, 1937

By J. C. Dumbrille

The following account of wining practices of the Kirkland Late Gold twining Co., (Ltd.), at Kirkland Lake, Ontario, is one of 4 series of papers being prepared by the United States Bureau of Mines on mining practices, methods, sad costs in various districts. The author has prepared this paper with the help and permission of J. B. Tyrrell and W. M. Sixt, the managing director and the mine manager, respectively. This mine is operating at a daily rate of about 150 tons.

Jan 1, 1931

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

By William M. Thornton

[Owing to the comparatively high freezing point of nitroglycerin (14, 15, 16, 17, 18, 23, 37, 38)3/ - 1.9° C. and 13.0° C. for the labile and stabile modifications, respectively, as determined by Hibbert (16) - manufacturers of dynamites have incorporated into the liquid portion of these composite explosives various substances capable of participating in an explosion, to depress the above-mentioned freezing point. Aromatic nitro-compounds, chiefly nitrobenzenes, nitrotoluenes, and nitronaphthalenes, have been used to a considerable extent (11), but such nitrosubstitution products have not proved altogether satisfactory, as has been shown clearly by Naoúm. (14). Consequently there has been a strong tendency in recent years to replace them with one or more of several nitric esters, among which the following (29, 35) have been prominent: Dinitrochlorhydrin (monochlorhydrin dinitrate); nitrosugars, for example, sucrose octanitrate (19); tetranitrodiglycerin (diglycerin tetranitrate); nitroglycol (ethyleneglycol dinitrate); and diethyleneglycol dinitrate (13, 46, 47). Of these, nitroglycol (33, 4l, 45, 48, 49, 65) is outstanding in importance. As the Bureau of fines is naturally interested in the analytical chemistry of the "explosive oils," it seemed desirable to bring together in this report the widely scattered experimental work covering the problem of differentiation that has appeared in various chemical and physicochemical publications.]

Jan 1, 1941

By Guy A. Johnson

To improve productivity and cut costs, modern underground mining operations have become more mechanized. This mechanization has increased the usage of fuels, hydraulics, and electrical equipment associated with diesel-powered vehicles, thereby also increasing the hazards of underground mine fires. The Bureau of Mines evaluated the fire hazard problem and assembled prototype components for a system that would automatically sense and extinguish fires on mobile underground equipment. The prototype system and alternative designs were in-mine-tested and proved effective. This report summarizes this technology, which can cost effectively help solve the problem of fire hazards on underground vehicles.

Jan 1, 1983

Surface mining and reclamation of a southeastern Ohio site with sandstone-shale overburden resulted in (as compared to premining levels): 1) runoff volumes and peak rates that increased by a factor of from 2 to 10 during mining and after reclamation, 2) destruction of the "aquifer" perched on the underclay of the mined coal bed and gradual, but, as yet incomplete redevelopment of this aquifer after reclamation, 3) no immediate effect on another, lower perched "aquifer", 4) up to 100 times greater sediment concentrations in runoff. Results were influenced by increasing annual precipitation amounts through the period of record; 1978, 1979, and 1980 (postreclamation years) experienced precipitation amounts approaching or exceeding long-term normalcy for the area. Part of the reason that the site produced more runoff after reclamation than before mining is that the premine condition was one of an open, porous soil under woodland, while the postreclamation condition was one of a compacted, bulldozed soil. Sediment concentration results were influenced by failure of the postreclamation erosion control system and by a series of detention reservoirs above the stream monitoring station.

Jan 1, 1983

By A. C. Rice

This report describes a chemical process for preparing solutions of trivalent rare-earth chlorides from sulfate solutions obtained by treating bastnasite concentrate. The chief impurity in the final solution is cerium, and this element is less than 1 percent of the rare-earth oxides. The solution is used directly in the separation of rare-earth elements by ion-exchange methods. The attractive features of the process are that the chemicals are inexpensive and the steps few. The process starts with precipitating the rare-earth hydroxides from sulfate solutions with caustic soda. After the hydroxides are dried to oxidize the cerium, they are treated with dilute hydrochloric acid to dissolve away the trivalent rare-earth elements, leaving the tetravalent cerium. Details for controlling the leaching step are described. The process shortens older procedures by omitting the usual oxalate or double-sulfate-precipitation step.

Jan 1, 1959

By Frank G. Horino

A rock mechanics program (composed of laboratory and field tests) was initiated by the Bureau of Mines in an effort to determine the causes of pillar instability at the Fletcher mine, near Bunker, Mo. Compressive strength, Young's modulus, shear strength, and the angle and coefficient of internal friction were determined on drill cores obtained from 16 different locations in the mine. Results of the laboratory tests showed that highly mineralized zones and brecciated zones in pillars could significantly affect pillar strengths and stability in locations where extraction ratios exceeded the normal design ratio of approximately 78%. High-angle fractures that were present in Some locations also may have contributed to pillar deterioration. In the field tests, in situ stress determinations were made in one pillar to establish the pillar-loading conditions and to evaluate the stability of the pillar. Continued monitoring of stresses in the pillar showed a gradual decrease in compressive stress, indicating that the pillar was probably in the postfailure state. A second stress determination was made in a vertical hole in the underlying igneous rock that was exposed on one section of the mine. Horizontal stresses were compressive and larger than would be expected from gravity loading.

Jan 1, 1978

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2 ) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs' estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By F. J. Palumbo

An electronic color-sorting machine was tested for recovering colorless glass concentrates from mixed glass products. The tests were made using glass recovered from unincinerated (raw) urban refuse and residues resulting from the incineration of refuse. The results of the study revealed that concentrates analyzing about 86 percent colorless glass could be recovered from mixed unincinerated glass containing 54 percent colorless glass material. Recovery of the colorless glass was about 62 percent. Color sorting the incinerated glass was somewhat more difficult. Multiple-stage processing was required to recover 59 percent of the colorless glass material in a product analyzing 89 percent colorless glass. The feed material analyzed 41 percent colorless glass.

Jan 1, 1971

By M. A. Elliott

Diesel-powered haulage equipment has recently been tested and approved for permissibility by the Bureau of Mines for use in mining in the United States. Achievement of this advance in safety involved extensive studies, both in the testing station (2, 3, 20, 21, 22, 23, 24, 25, 26, 27)3/ and in the field 1, 4, 13, 30), of the operating characteristics of diesel engines in relation to the toe of such engines underground. The results of these studies formed the basis for establishing the requirements that should be met by diesel-powered haulage equipment approved for permissibility. Considerable interest has been manifested in the development of diesel-powered haulage equipment fur mines. The purpose of this paper is to retrace briefly the course of this development and to answer such questions as: What is the history of the use of diesel engines underground? Why has the Bureau of Mines been interested in the development of diesel-powered haulage equipment for use in mines?

Jan 1, 1953

By Benjamin W. Haynes

This research was conducted as part of the U.S. Department of the Interior, Bureau of Mines program to recover metals, glass, and a combustible fraction from municipal solid waste (MSW). The objective of this analytical study was to determine the concentration of antimony, arsenic, and mercury in samples taken from various sampling areas in the Bureau of Mines raw refuse recycling plant and to compare these values with those for coals used in the generation of electricity. To provide the necessary analytical data, sensitive reproducible ashing-chemical digestion-atomic absorption procedures were adapted from published procedures. It was determined that antimony and mercury concentrations in the combustible fraction of MSW are approximately an order of magnitude higher than those found in coals presently used for power generation;' the arsenic concentration is similar in both fuels.

Jan 1, 1978

In 1962 and 1963, two in situ combustion pilot tests were conducted in the shallow Second Venango sand near Reno, Pa. Because of poor oxygen utilization and lack of production response, both tests were considered failures and were terminated. The area was then relatively inactive until late 1966, when a development well drilled near the 1963 test site had surprisingly good production in what was considered to be a pressure-depleted reservoir. Other wells drilled in and around the old thermal pilot areas also came in as good oil producers. This report presents a study of the increased oil production from the Second Venango sand in the Reno area, and the apparent connection of the present production response and the old thermal pilot tests. Apparently combustion occurred in the Second Venango sand after the 1962 and 1963 experiments were terminated and, supported by large volumes of air left in the reservoir after the 1963 test, generated carbon dioxide which helped repressure the formation. This field evidence of combustion warrants another pilot experiment to further explore the use of properly designed in situ combustion techniques in increasing production from the Second Venango sand.

Jan 1, 1971

By O. Q. Leone

Composite diaphragms were used in the investigation of electrowinning Ti from TiC14 in a fused LiCl-KCI-TiC'2 electrolyte. Composite diaphragms tested were of two general classes--those consisting of two or more solid materials, and those which contained, in addition, a loose material. An electrowinning cell using a flat diaphragm is described. The maximum current density for these diaphragms was 300 amp per ft2. Lower currents permitted longer operation times. The composite diaphragms gave electrode efficiencies that averaged approximately 60 percent, and the electrowon titanium was of good quality--some Brinell hardnesses were as low as 68.

Jan 1, 1972

By W. K. Collins

Engineered scavenger compounds (ESC's) developed by the U.S. Bureau of Mines are a novel class of compounds that selectively can recover a desired element from a solid or molten alloy. Lithium titanate (L2Ti307 or Li2O?3Ti02) is used as an ESC to recover lithium (Li) from aluminum-lithium (Al-Li) alloys. X-ray diffraction measurements have shown that Li2Ti307 undergoes a phase change during scavenging from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of lithium in the matrix of the material and the effect of temperature. Although both phases are metastable, the hexagonal phase that forms during the scavenging of lithium from Al-Li alloys appears to be the more stable phase. Recovering lithium from the ESC by electrodeposition does not cause the structure to revert to the orthorhombic phase. The orthorhombic and the hexagonal structures of Li2Ti307 have similar scavenging capacities for lithium. This report proposes a new mechanism for the phase transformation.

Jan 1, 2010

By E. P. Youngman

A new mining law for the Recublic of Polend was promulgated by presiden- tial decree dated November 29, 1930, published in the Journal of Lews (Dzienni stex) No. E, text 654, December E, 1530, and wes to become effective January 1, 1932, in all Polend except Silesie. Its adoption in Silesia wes dependent pon the action of the Silesian Diet. As the new law is considered an im- provement over the old Austrian Mining Lew, which is operative in the Silesian districts of Bielsk and Cieszyn, and the Prussian Kining Law, which is opera- tive in Upper Silesia, no delay in its adoption for Silesin was looked for. This new law codifies the various juridical regulations pertaining to ines existing in different parts of the Polish Republic but does not include legislation with respect to the extraction of minerel oil, especially crude oil. Petroleum legislation was postponed to a later date in order to facili- tate codification in other fields. Koreover, as the oil industry exists in Galicia elone, deley will not be detrimental.

May 1, 1932

By Ellis S. Hertzog

The data published in this report cover only one phase of a special study of the physical and chemical properties of Alabama coals made by the Bureau of Mines. In addition to determinations of friability, the survey included determinations of grindability, B.t.u. value, end ash-fusion temperature. Assay distillation tests, both for high- and low-temperature carbonization, and proximate and ultimate analyses were made also. However, this preliminary paper is concerned only with the results of friability tests and is issued to expedite the release of this information to the public. The friability test measures the liability of a coal to break into smaller pieces when subjected to repeated handling, as occurs in the mining, preparation, and transportation operations. Friability depends on many physical characteristics of the coal that vary not only between different seams but also in the same seam. The laboratory methods of determining friability have been developed to give a practical means of estimating degradation of size. So far as is known to the authors, no data on the friability of Alabama coals have ever been published. This paper makes available for the first tine fairly comprehensive information on this subject. Because the procedure for the tumbler test for determining the friability of coal is relatively new to the coal operators, the authors have included a complete description of it in this report.

Jan 1, 1938

By Robert W. Geehan

"INTRODUCTION A preliminary examination of the Argentena mine was made in 'January 1945 by an engineer of the Bureau, who recommended investigation by diamond drilling. The Bureau conducted a core-drilling project at the mine from April 30 to August 4, 1946. Claims investigated are in sec. 33, T. 24 S., R. 58 E., Mount Diablo base and meridian, in southern Clark County, Nev., about 2.2 miles west of Goodsprings.The Argentena mine has been an intermittent producer of zinc-lead-silver ore since 1926. During the war years, ore was shipped to the Government stock pile at Jean, Nev., and to the International Smelting F. Refining Co.'s smelter at Salt Lake City, Utah. The mine has been shut down at intervals because of lack of a market for mixed oxidized zinc-lead ore.The 12 holes drilled by the Bureau totaled 1902 feet. The program was designed to test for faulted portions of the ore bodies know in the mine and to test favorable areas for similar ore bodies. As a result of this program, one faulted segment of the ore body was found, and it was established that no one was present in a second fault block. Similar blocks remain unexplored in the vicinity of the mine. Two holes drilled in favorable areas several hundred feet from the mine failed to discover new ore bodies."

Jul 1, 1947

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954