Search Documents

By Charles L. Kimbell

Available statistics on 1989 worldwide consumption of selected nonfuel minerals shown in table 5 show increases for 11 of 14 listed nonfuel mineral commodities with 1 unchanged from the 1988 level, a departure from the pattern of the past 2 years, in which each of the listed commodities registered gains. The 1989 results, however, were better than those for 1986 when only seven listed nonfuel mineral commodities recorded gains with one un- changed from 1985. Consumption of the two ferrous metal raw materials listed advanced as functions of increased output of pig iron and crude steel. The increase in iron ore consumption exceeded the increase in iron ore output, suggesting a slight drawdown of world iron ore inventories. The estimated in- crease in iron and steel scrap consumption was slightly greater than the minuscule increase in world steel production, but it is believed that there was little change in the ratio of iron ore to scrap in steel plant feed on a global basis.

Jan 1, 1992

By T. M. Kohler, G. L. Finfinger, D. M. Hyman, A. T. Iannacchione

The Bureau of Mines measured methane emission rates from an advancing salt face ranging from 15 to 56 ft3/ton (0.5 to 1.8 m3/t). Small room size, use of a continuous miner, and a well-defined ventilation system made possible air velocity and methane concentration measurements, These measurements, representing data from 18 production days, were con- ducted in an area of abnormally low grade salt, Methane emissions occurred primarily during the advance of the salt face by continuous miner.

Jan 1, 1982

By John Durkin

The Bureau of Mines has conducted field studies in coal mines through- out the United States to determine the effectiveness of electromagnetic techniques in locating miners trapped underground following a mine accident. Data from these tests have been used to generate models of expected signal and noise distributions as found above mines throughout the coalfields. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results show that at a 10-pct false alarm rate, the expected probability of detecting a miner's signal from a depth of 1,000 ft is 54 pct; at 500 ft it is 95 pct. These depths exceed the actual depths of 90 pct and 50 pct, respectively, of U.S. coal mines. Sensitivity studies have shown that at a depth of 1,000 ft, for every 3 db of improvement in signal-to-noise ratio, the probability of detection increases 6 to 8 pct.

Jan 1, 1982

By Gregory M. Molinda

The Bureau of Mines conducted an investigation into the occurrence of outbursts of salt known to be responsible for explosions, fatalities, and damage in domal salt mines. The purpose of the investigation was to develop a basis for predicting these outbursts based on geologic and associated physical properties of salt. The investigation was conducted at the Cote Blanche salt mine in southern Louisiana. Because outbursts are the primary mode of methane emission into the mine, more than 80 outbursts, ranging in size from 1 to 50 ft in diameter have been mapped. These outbursts generally are aligned and elongate parallel to the direction of salt layering. More than 200 salt samples, both random and selected, were tested for methane content. It was found that outburst zones are well correlated with high methane content. Detailed mapping also revealed that the zones are well defined, with salt crystal size abruptly increasing upon entry into the zone. The intensity of folding and kinking of the salt layering within the outburst zone also appears to increase. An interbedded sand layer occurring throughout the mine does not appear to be a significant source of methane. However, fine-grained salt may be related to outburst occurrence.

Jan 1, 1988

By R. Pakalnis, Richard P. Curtin, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control to monitor rock mass loads at various field sites (FMC Granger, Getchell, Meikle, SSX, K-2, and Stillwater). Axial and shear loads were determined by strain gauges to levels of instrument accuracy of ±5 N or ±5 microstrain as these loads were transferred to the instrumented cable bolts. These gauges were 12.5 mm long and embedded into are manufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. By monitoring load on and displacement of the rock mass, more effective ground support can be selected and installed, which will lead to safer working conditions for miners.

By William A. Vogely

HIGH ACTIVITY, continuing the substantial recovery from the slump of 1954, characterized the domestic nonfuels-mining industries during 1956 Income generated in producing nonfuel minerals and mineral products3 increased 9 percent over 1955 as compared with a 6-percent increase for all industries. Thus, the 1956 performance of the mineral industries, while not as dramatic as the 27-percent increase obtained in 1955, continued to exceed the gains of the total economy. Other measures of mineral activity strengthen this conclusion. The index of physical volume of mineral production, presented for the first time as an integral part of this review, reflects significant gains in all major sectors during 1956; and, although the overall increase was diminished somewhat by the steel and iron-ore strike in July 1956, the all-mineral index (including fuels) reached a new high.

Jan 1, 1958

By Richard G. Sandberg

Sphalerite concentrates prepared during processing of Missouri lead ores contain small percentages of cobalt and nickel which adversely affect zinc electrolysis. The Bureau of Mines has evaluated solvent extraction and precipitation techniques to remove and recover cobalt and nickel from zinc sulfate solution prior to zinc electrolysis. Prepared zinc sulfate solutions containing about 190 gpl of zinc and 50 ppm of both cobalt and nickel were treated using various combinations of complexing reagents, solvent, pH, concentration, time, and temperature. The following complexing reagents gave the best results: a-nitroso-ß-naphthol, ß-nitroso-a-naphthol, 1,2 cyclohexane dione dioxime (nioxime), di-2-pyridyl ketone oxime, and dimethylglyoxime. These reagents in suitable solvents lowered the cobalt and nickel levels to <0.1 ppm. Stripping the complexed reagents from the solvents was not possible except for nioxime. Direct addition of the appropriate reagent to the prepared zinc sulfate solution resulted in the precipitation of cobalt and nickel. Several possible flowsheets are presented for the removal and recovery of cobalt and nickel. Good zinc deposits were successfully electrowon from zinc sulfate solutions purified by solvent extraction and precipitation.

Jan 1, 1978

By W. S. Anderson

The use of flexible liners for support of underground openings has been investigated by the Bureau of Mines. This report presents installation procedures and instrumentation results of a full-scale flexible liner field installation in the Burgin mine. The flexible liner is a part of the mine support system and has provided maintenance-free support for 22 months

Jan 1, 1975

By D. R. Tesarik

An instrumentation and numeric modeling study was conducted by the Bureau of Mines at the Magmont Mine in Bixby, MO. An isolated section of this room-and-pillar mine was monitored with borehole and closure extensometers during a pillar recovery program to determine stress redistribution. In situ stress measurements were taken in the rib before pillar extraction began. Sample cores from the boreholes were taken for analysis of the properties of the host rock in the laboratory. The extensometers recorded no measurable displacements during most of the operation. Two-dimensional, finite-element; three-dimensional, finite-element; and three-dimensional displace-ment discontinuity codes were used to model the area of study. The finite-element models were run with two initial stress conditions, i.e., stress due to gravity only and stress obtained by in situ measurements. Horizontal stresses in the models reduced the calculated factor-of-safety in the mine back by up to a factor of 10, but did not have a significant effect on calculated pillar stability.

Jan 1, 1989

By Martin Hertzberg

The Bureau of Mines 8-liter flammability system was used to study the effectiveness of a variety of powdered inhibitors in preventing the propagation of explosions of coal dust or methane in air. Over 35 different chemical additives were evaluated against Pittsburgh seam pulverized coal. The least effective inhibitors were the carbonates, which required mass additions in the range of two to three parts inhibitor to one part of coal dust in order to prevent propagation. The most effective inhibitors were the derivatives of ammonium phosphate, which were effective quenching agents at additions of only one part inhibitor to four parts of coal dust. Alkali halide powders were of intermediate effectiveness. These laboratory-scale results are in good agreement with full-scale mine experiments in all cases where detailed comparisons have been made. Data were also obtained for the effectiveness of several of the same powdered inhibitors against methane-air explosions. Their relative order of effectiveness and the concentration ranges required for quenching the gas explosion are comparable to those measured for coal dust explosions. Data are also presented for the effectiveness of N2 and CF3Br addition. Some preliminary data are also presented for powder addition to methane burner flames. Those data are compared with other burner data and evaluated in terms of their relevance to explosion tests.

Jan 1, 1982

By R. H. Grau, S. B. Robertson, R. B. Krog, T. P. Mucho

Stone mines represent the highest percentage of operating underground nonmetal mines in the United States. With the introduction of stricter Diesel Particular Matter (DPM) regulations, large-opening underground room-and-pillar stone mine operators are faced with implementing one or more alternative methods to reduce concentration levels including: install and maintain an effective ventilation system; install lower DPM emission diesel engines; the adding of DPM filters. The National Institute for Occupational Safety and Health (NIOSH) is actively researching various aspects of fan and stopping designs in an effort to improve the ventilation of these mines. NIOSH has identified and further developed three alternative ventilation methods for use in large-opening underground mines: split-mine, perimeter, and unit-ventilation. This paper describes the implementation of the three methods with respect to their use in mines of various levels of development.

By Perry G. Cotter

The objective of this investigation was to synthesize and investigate the properties of a high-temperature refractory material based on a combination of boron, silica, and magnesium. A magnesium-thermic reaction was used for the synthesis. X-ray examination of the product indicates that the crystalline portion of the composition is a combination of magnesium borides, magnesium silicate, and magnesium orthoborate. Chemical analysis of a representative sample shows, in weight-percent, boron 17.6, silicon 23.9, magnesium 17.8, and chromium 0.5. The balance is largely oxygen. The composition is resistant to high temperatures under oxidizing conditions and is stable in water, hydrochloric acid, and hydrogen. It has a low density (less than 3 grams per cubic centimeter) and a hardness value in the range of quartz. It has a melting point above 1,700° C. and can be hot-pressed to shape in the temperature range between 1,200° and 1,350° C. The properties described in this paper indicate that the material may have some uses as a high-temperature refractory, and because of its boron content it may have some value as a thermal-neutron-absorption material.

Jan 1, 1961

By F. B. Petermann

Two-stage electric smelting tests, using small submerged arc furnaces, were made on high-iron manganiferous materials from the Pioche District, Nev., and the Cuyuna Range, Minn. The object was to reduce sufficient iron in the first stage to give a slag with a favorable Mn to Fe ratio for smelting to ferromanganese in the second stage. The nodulized flotation concentrate from the Pioche District contained 29.2 percent Mn and had a Mn to Fe ratio of 2.3:l. When smelted with coke and silica or alumina as flux, more than 90 percent of the manganese was recovered in slags with Mn to Fe ratios of 10: :24:1. The Pioche slag was smelted to ferromanganese using coke and lime- stone or dolomite as flux. The ferromanganese was high in silicon but other- wise met specifications. Recovery of manganese to ferromanganese in this step was 73 to 78 percent. Overall recovery of manganese was about 70 percent. The sintered flotation concentrate from the Cuyuna Range material contained 12.9 percent Mn and had a Mn to Fe ratio of 0.3:1. When smelted with limestone as flux, about 83 percent of the manganese was recovered in a slag with a Mn to Fe ratio of about 6:1. The Cuyuna slag was smelted to ferromanganese with coke and limestone for flux. Recovery in this step was 61 percent of the manganese in a high silicon ferromanganese. Overall recovery of manganese was about 50 percent.

Jan 1, 1963

By Martin Hertzberg

The concept of limit burning velocities is being used to formulate a quantitative theory of flammability limits. Competing and complicating processes dissipate power from a combustion wave and quench propagation at some characteristically low limit velocity. Two earlier reports dealt with process (a), natural convection (RI 8127); and with process (b), conductive-convective wall losses (RI 8469). This report considers process (c), radiative losses, and process (d), selective diffusional demixing. The limit burning velocity for radiative losses is [(SU)c ~ e cp] It is normally not a significant process for premixed gas flames; however, for laminar flame propagation in a gravity-free environment, it is the only loss process present. Accordingly, limit velocities at zero gravity should be much lower than on earth, and premixed gases should be flammable over wider composition ranges. For highly emissive dusts, soot, or ash-forming flames, radiative losses are significant even under normal gravity conditions. Selective diffusional demixing is a complication that manifests itself in the form of cellular flame structures and wide gaps in composition between upward and downward propagation limits. It induces a burning velocity shift (?Su)d, causing the flame to behave as though it were richer or leaner than its initial composition, depending on whether the fuel or the oxidizer mole¬cule has the higher diffusivity. A simple pertubation analysis shows that the process generates stable cellular flames whenever [dsu] > 0, where ci is the concentration of the reactant with the higher diffusivity. The same analysis indicates that at the opposite stoichiometry, where [dcu] < 0, laminar structures are stabilized. A simple formula for the diameter of cellular flames is derived, which predicts that dcell should vary inversely with the product of the diffusivity difference Di -DJ, and the burning velocity slope [dc ]. Those predictions are in good agreement with the available data. Buoyancy forces for upward propagation induce flame front curvature, and hence buoyancy and selective diffusion are mutually supportive in upward propagation. Thus large gaps in composition between upward and downward limits are present in those composition domains where cellular flames are stable.

Jan 1, 1981

By Fred C. Turin, William J. Wiehagen

This study examined musculoskeletal injury risk at four mining sites: underground coal, underground limestone, surface copper, and surface phosphate. Each site offered opportunities to investigate musculoskeletal disorder (MSD) injury risks and how those risks might be identified and categorized. The National Institute for Occupational Safety and Health (NIOSH) worked with these sites to (1) identify work activities that showed evidence of MSD injury risk, (2) examine physical risk factors that can lead to MSDs for a handful of work tasks at each site, and (3) develop a set of ideas for problem-solving to help reduce risk factors for examined work tasks. For each site, NIOSH implemented a plan that was refined over the time period of this study. The plan consisted of four steps. The first step was to use mine injury records, a musculoskeletal discomfort questionnaire, front-line supervisor interviews, and a list of management concerns to identify work groups and work activities that have significant evidence of MSD risk factors. The second step was to select work tasks for evaluation. The third step was to interview those who do the work and make observations to characterize the MSD risk factors and musculoskeletal symptoms that exist for target tasks. The final step was to conduct brainstorming sessions with workers who perform the work or have a stake in the production task. The brainstorming sessions served to identify general strategies (ideas) for reducing MSD risk factor exposures. A final report of findings was presented to mine management and workforce representatives at each site. The risk factors and ideas for improvement identified for each site were specific to the target tasks examined. These target tasks were diverse, but there were some key similarities. For instance, jobs were found at each site that required a significant amount of manual work involving the upper extremities and low back. Handling heavy and awkward objects, forceful arm and shoulder exertions, and working in awkward postures were common for a variety of jobs across the four sites.

Jan 8, 2004

By Paul R. Amyotte, Omotayo Kalejaiye, Kenneth L. Cashdollar, Michael J. Pegg

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRI, 20-L and Fike 1 -m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1 -m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

By C. S. Compton, T. E. Marshall, D. R. Dolinar, R. Grau, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels&apos;. Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m (26.5 ft) above the miner&apos;s head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roof beam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

By C. P. Lazzara, Y. Miron, A. C. Smith

This report presents a U.S. Bureau of Mines study to identify the causes of self-heating events beneath the floor of a deep underground coal mine. Mine samples from both heated and unheated areas were examined by various techniques, including visual, microscopic, thermal, chemical, and instrumental tests. The combined results led to the conclusion that pyrite (FeS2) oxidation was the prime cause of the beatings. However, adiabatic oven tests of selected samples did not indicate the effect of the pyrite on the self-heating process, probably because of the experimental conditions. A fast, simple procedure to assess the concentration of pyrite in the mine samples was developed, utilizing the reactivity of the sample with an aqueous solution of hydrogen peroxide (H2O2)

Jan 1, 1992

By J. P. Conway

The yielding-rock-bolt concept, as developed in South Africa, consists of a smooth-bore die or collar fitted to a standard rock bolt. Laboratory testing at the Bureau of Mines Spokane Mining Research Center under slow and fast strain rates showed that extrusion loads can be controlled by varying the configuration of the die bore and that theoretical analysis (using basically Sachs&apos; theory of wire drawing) predicts extrusion loads of the different die-bore configurations. A derived equation, based on this research, can be used for designed die-thread combinations for any desired extrusion load. Dynamic loading resulted in slightly higher loads (15 percent) than static loading. The strain hardening effect, which increases yield and ultimate strength, was partly offset by adiabatic heating of the threads, which decreases strength.

Jan 1, 1975

By Charles W. Huggins

DEVELOPMENT of the electron microscope has permitted man to examine many small objects that could not be resolved by the light micro-scope. Diffraction, spherical aberration, and chromatic aberration are the main factors that limit resolution to about two-tenths micron with the light microscope. No matter how perfectly a light microscope is constructed and operated, it cannot possibly resolve points separated by less than two-tenths micron. Rapid development following World War II has produced many electron microscopes capable of 20 A resolution. Fibrous inorganic minerals are well suited for electron microscopic study. Many micrographs of chrysotile have been published, but electron microscopic study of the amphiboles has been somewhat neglected. New techniques in sample preparation have simplified the study of fibrous material. Ultrasonic energy has been very helpful in sample dispersion. This publication contains a representative group of electron micrographs of natural inorganic fibers that have industrial value. These fibers commonly are referred to as the asbestiform minerals. The Bureau hopes that the knowledge gained through electron microscopy and other scientific study of the natural inorganic crystalline fibers eventually will lead to the production of synthetic fibers that will satisfy the requirements of industry.

Jan 1, 1959