Search Documents

By Gerald T. Homce

Accidental contact of overhead electrical power lines by mobile equipment is a leading cause of occupational fatalities in the United States, accounting for 20% of on-the-job electrocutions. Overhead electrical power line proximity warning devices (PWDs) are intended to warn personnel if mobile equipment moves within some preselected minimum distance of an energized overhead electrical power line. Two commercially available PWDs were tested at the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). The objective of the tests was to document performance capabilities and limitations for these PWDs by identifying factors that can influence their operation. The two PWDs evaluated in this research are the SIGALARM Model 210 marketed by Allied Safety Systems, LLC, and the ASE Model 2100 from Allied Safety Engineering. Both of these devices operate by measuring the electric field present around energized power lines. The PWDs were installed on a government-owned 22-st (20-mt) rough terrain crane. A purpose-built test site used for this research at PRL allowed operation of the crane near a variety of power line configurations operating at up to 25 kV. Most of the tests involved positioning the crane adjacent to one or more overhead power lines, adjusting sensitivities of the PWDs to alarm when the crane boom was approximately 20 ft (6.1 m) from the power lines, swinging the crane boom toward the lines under a wide variety of test conditions, and finally, for each unique set of test conditions, documenting the deviation from 20 ft (6.1 m) for actual alarm activation. Test results show that several factors can adversely affect PWD performance. PWD alarm accuracy generally deteriorated when operating with a boom position significantly different than that used for the device?s last sensitivity adjustment. Another factor that can affect PWD performance is configuration of the overhead power line(s) involved. Accuracy of alarm activa­tion distances was best for simple single-circuit installations, but degraded for multiple circuits on the same poles. This degradation was slightly greater for installations with different voltage levels and/or a combination of vertical and horizontal conductor arrangements. Performance also degraded for crane operation between two intersecting power line installations, especially for intersecting lines at different voltages. An additional aspect of power line configuration shown to influence PWD accuracy was phase sequence on the power line circuit(s). Specific phase con­ductor arrangements and combinations, particularly in multiple circuit installations, resulted in either improved or degraded accuracy.

Jan 1, 2008

By S. K. R. Iyengar

This report presents the results of a study to develop optimal designs for light-weight mine roof supports for use in underground coal mines. A load capacity of 196 kN (22 tons) and a height adjustable between 1.829 m (72 inches) and 2.438 m (96 inches) were taken as the design parameters and the design goal was a unit weighing less than 22.3 kg (50 lbs). Three alternative design concepts were explored, viz. mechanical, hydraulic, and hydro-mechanical and a total of 13 designs analyzed in detail. Steel, aluminum alloy and composites were the main potential construction materials investigated for suitability from structural, life, and safety and other considerations. The designs considered most promising for development were: (i) the mechanical screw-pin type using telescopic tubes and a fine adjustment screw thread section (ii) the all-hydraulic type, of steel, aluminum alloy or aramid graphite construction (iii) the hydro-mechanical design using telescopic tubes and a short stroke hydraulic cylinder for fine adjustment It is shown that by using realistic mathematical models for stress and deflection calculations, it is possible to reduce prop weight to the design goal. The analysis presented for all-hydraulic props is applicable to hydraulic cylinders on all mining equipment and similar machinery. This report includes the computer program and user's guide for analyzing hydraulic cylinders as well as a cross-indexed bibliography on structural composites.

Jan 1, 1978

By W. I. Watson

The study considered all the institutional, resource reserve, technological, and economic factors relevant to the industry's present and future status, such as markets and marketing techniques, competition from other producers both domestic and foreign, federal and state regulations affecting the industry, quarrying and processing technologies, slate reserves and resources, and industry structure and economics. Constraints to the growth of the industry were assessed and scenarios proposed to solve some of the problems.

Jan 1, 1980

By L. Nahai

In two decades Turkey has emerged from the debacle of the Ottoman Empire to become one of the most modern nations in the Middle East. The numerous achievements of this period were remarkable in that they affected human and social, as well as economic, fields. Most of this progress was achieved by Turkey's unaided efforts and the utilization of domestic resources; however, since 1948 various United States aid programs3/ have made significant contributions to increased agricultural and industrial output. Turkey's singleness of purpose in favor of a strong, independent, and prosperous republic has evoked universal admiration and encouraged the hope of stability in the Middle East. Much of the development of the Turkish economy to date has been fostered by the State; however, with growing strength the leaders in 1950 considered the time appro¬priate to relax the nationalistic economic policy and permit private enterprise to play a larger role in increasing domestic output and raising the tempo of industrialization. In pursuance! Of this policy, laws encouraging investment of foreign capital in Turkey and others stimulating development of mining and petroleum enterprises were enacted in 1954. This new legislation, plus the cooperative attitude of the Turkish Government, have encouraged wide interest in the mineral resources of the country.

Jan 1, 1958

Data recently released indicate substantial improvement in mineral industry performance for 1984. Business plans to increase plant and equipment spending in 1984 by 14.8 percent, according to a recent survey conducted by the Commerce Department's Bureau of Economic Analysis (table 1). In contrast, capital spending by all industries declined 4.8 percent in 1983 and 2.3 percent in 1982. The latest estimate of planned expenditures for 1984 is $2.2 billion higher than the comparable estimate based on the survey conducted in late January and February 1984.1/ [ ] Of particular significance to the U.S. mineral industries are the 15.5-percent increase in capital spending planned by manufacturing in 1984 and the planned 18.6-percent increase in spending by durable goods manufacturing, where the largest increases are planned in the transportation equipment (26.4 percent) and electrical machinery sectors (23.5 percent). Capital expenditures in manufacturing declined in both 1982 and 1983.

Jan 1, 1984

By Shelby Z. Palya

"The Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mining-substances; to promote health and safety, in the mineral industries; to conserve Material resources , and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other Mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1975, to December 31, 1979. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960; 2 the 50-year list, of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960; 3 the 5-year lists of publications and articles, from January 1, 1960, to December 31, 1964,, from January 1, .1965, to December 31, 1969,5 'and from January '1, 1970, to December 31, 1974; and the annual ,lists of Bureau publications and articles from January, 1 to December 31, 1975,7 from January 1, to December 31, 1976,8 from January 1 to December 31, 1977, and from January 1 to December 31, 1978."

Jan 1, 1981

By Virgil Miller, Glenn L. Allen

The purpose of this report is to present a comprehensive review of the technology of alumina and aluminum production in the former Japanese Empire , which consisted of the Japanese Home Islands and her dependencies , Formosa , Manchuria , and Korea . Pertinent background material and statistics are given when deemed necessary to make the report self - contained and to make clear the factors underlying Japan's tremendous accomplishments in the production of aluminum .

Apr 1, 1949

By James R. Wait

An attempt is made here to collect together various reports and publications that are based on research supported all or in part by Contract No. H0155008 for the past two years. The subject matter deals primarily with the excitation, transmission, and reception of electromagnetic waves in mine environments. This contract from the U.S. Bureau of Mines with the Office of Telecommunications supports the efforts of James R. Wait (Principal Investigator and Consultant to OT), David A. Hill (Co-Investigator), and various associates within the Boulder scientific community. The contributions of Samir F. Mahmoud were supported, in part, by the contract while he was a Visiting Fellow with the Cooperative Institute for Research in Environmental Sciences at the University of Colorado. Administrative assistance in CIRES has been provided by Mrs. Lana R. Hope.

Jan 1, 1976

By F. Albayrak

This report is a study of the impact of Federal laws and regulations on the domestic supply of metallic and nonmetallic minerals. The study was confined to pertinent environmental legislation and the recently enacted Federal Mine Safety and Health Act of 1977. Emphasized were the legal requirements placed on individual selected mineral industries, and the economic impact of these requirements. A certain amount of attention was also directed to the particular environmental and health and safety problems generated by selected mineral industries. The study also pinpointed a list of major problem areas having significant impact on the domestic mineral supply.

Jan 1, 1978

By R. D. Leitch

"INTRODUCTION The character of mine drainage from areas of low pyritic coal3 and from average pyritic coal4 has been investigated, and to complete the study it seemed desirable to select a number of mines situated in high pyritic are as to determine whether or not this variation determines the relative acidity of drainage from mines operating in these characteristic coal fields. Advantage has been taken of some worked on in 1918 by Henry Leighton 5, then Professor of Economic Geology, University of Pittsburgh. He visited and has reported certain areas of high pyritic coal which we also visited during this study. Many of the mines were found to be idle in 1930 and a few were caved shut, apparently for several years. However, samples of the outflow from all mines visited were collected if possible and analyzed, and some general information was gathered for each mine. The map (fig. 1) shows the location of these areas as given by Leighton.ACKNOWLEDGMENTSThe information and assistance obtained from officials and others at the mines visited during this study are gratefully acknowledged, as well as the original suggestion from Dr. Glenn V. Brown of the State Sanitary Water Board who called attention to the desirability of such a study.Thanks are also especially due the coal laboratory of the United States Bureau of Mines, under the direction of H. M. Cooper, for the analyses and determination of sulphur forms in the large number of solid samples necessary to the work reported,This study has been carried on under the direction of R. R. Sayers, chief, health and safety branch, and W. P. Yant, supervising engineer, Pittsburgh Experiment Station, of the U. S. Bureau of Mines."

Jan 1, 1932

By O. Llewellyn Jack

From September 1978 to December 1983, ESD Corporation (formerly a Division of FMC Corporation) undertook the development and testing of a bidirectional auger under contract with the U.S. Department of Energy. Underground testing began in August 1981 at Peabody Coal Company's Marissa Mine near Marissa, Illinois. The auger was developed to increase mine production and coal recovery without increasing land subsidence. It bored 4-foot-diameter by 10-foot-deep holes into pillars on 7-foot centers (each hole recovering 5 tons). All operating during this test was performed by maintenance personnel with the goal of finding ways to increase the machine potential. The maximum excavation rate achieved was 1.4 tons per minute. It was concluded that the concept of drilling short holes to extract coal from underground pillars without surface subsidence was practicable with a wheel mounted auger, but that more power was desirable for this mine, and that the hydraulically driven augering system that provided experimental versatility was not sufficiently reliable for production use.

Jan 1, 1983

By Gene R. Reid

The contract objective is the development and in mine testing of an Automatic Fire Control System (AFCS) for mobile underground metal mining equipment. The effort described by this report covers the period from June 21,1975 through June 30,1976 and accomplished the following tasks: ? Preparation of Data Handling Plan and data acquisition which included visits to twenty mine sites in eleven states, visits to Bureau and MESA facilities, and a literature survey. ? Data analysis which determined the most hazardous type of vehicle for use in the demonstration, and design requirements for the AFCS, ? Development of recommended design concepts for the AFCS. ? Design and development of the AFCS including tests on a full-scale mock-up of a load-haul-dump (LHD) vehicle. ? Underground fire tests on an ST-2B-LHD vehicle at the Hecla Lakeshore mine Casa Grande, Arizona.

Jan 1, 1976

By Katherine A. Margolis

Refuge Chamber Expectations Training was created by a multidisciplinary team at the National Institute for Occupational Safety and Health (NIOSH) to inform miners of what to expect psychologically and physically if it became necessary to use a refuge chamber in a mine emergency. The presentation can be used either for one large group or for individual miners. The training is a multimedia Adobe Flash presentation containing pictures, audio, video, and interviews with miners who have used a refuge chamber in an emergency. It must be run on a computer with Adobe Flash Player installed (refer to the computer system requirements section).

Oct 1, 2009

The original manuscript of section 2 of this series of miners' circulars devoted to accident prevention in bituminous-coal mines was completed in September 1944. At that time roof bolting had been tried with some success in the lead-mining district of south-eastern Missouri, but information on the subject was so fragmentary that it was not included as a method of roof support. References to roof support in bituminous-coal mines, therefore, were confined almost entirely to conventional timbering methods. In 1947 the Bureau instituted a research program and intensive study of the general problem of roof control, which emphasized roof-bolt application. The rapid increase in mechanized mining following the close of World War II provided the impetus for the Bureau's roof-control investigations, because the vertical supports used with conventional timber restricted the maneuverability of mechanical face equipment, and the industry wanted to explore every possible method of eliminating interference with the production cycle to gain full advantage of mechanized mining. Moreover, the accidental dislodgment of vertical supports greatly increased the roof-fall hazard. As roof falls have killed and seriously injured more mine workmen every year than any other cause or classification of injury since records have been kept, the Bureau assumed this investigative leadership with the prime objective of substantially reducing the annual toll from falls of roof, including falls of rib and face.

Jan 1, 1958

By Bureau of Mines Staff

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine venti lation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which ,accounts for a major portion of the market for coal, received further study. Unique power generation systems, inc luding coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jun 1, 1965

By J. W. Thompson

BURYING DEAD MINERS. BURYING BODIES OF DEAD MINERS. REVISED STATUTES (HURD) 1874, P. 263. SEC. 22. LIABILITY OF RAILROADS, ETC., FOR BURIAL EXPENSES.-When any railroad company, stage or any steamboat, propeller, or other vessel engaged in whole or in part in carrying passengers for hire, brings the dead body of any person into this State, or any person dies upon any railroad car or in such stage, steamboat, propeller or other vessel in this State, or any person is killed by cars, or machinery of any railroad company or by accident thereto or by accident to or upon any such stage, steamboat, propeller, or other vessel, or by accident to or in or about any mine, mill or manufactory,* the company or person owning or operating such cars, inachinery, stage, steamboat, propeller, or other vessel, mine, mill or manufactory shall be liable to pay the expenses of the coroner's inquest upon and burial of the deceased and the same may be recovered in the name of the County in any court of competent Jurisdiction. NOTE--The original Act of February 15, 1855 (Laws 1855, p. 170), makes no reference to the dead bodies of persons killed" by accident to, in or about any mine."

Jan 1, 1919

By William O. Vanderburg

This paper gives the results of a reconnaissance of the mining districts in Pershing County, Nev., made from March 9 to April 1, 1936. During the field work nearly all of the mining districts in the county were visited, and considerable data were obtained on active and inactive properties. The report covers the location of the various mining districts, nature of the deposits, information on past

Jan 1, 1936

This briefing was sponsored by the Bureau of Mines to summarize ongoing and recently completed chromium-chromite research and resource assessment activities by the Bureau. Through the series of 18 presentations compiled herein, Bureau personnel covered a wide range of topics including U.S. chromite and chromium trends and usage patterns; foreign and domestic resources; and research activities on mineral characterization and beneficiation, chemical and pryometallurgical processing of chromite and chromium-bearing wastes, new low-chromium alloy and coating substitutes, corrosion- and oxidation-resistant stainless steels, and chromium-containing refractories.

Jan 1, 1986

[lllc purpabr at thla report Vd, Lu JeLermlnr the health ar1J sdfet?; Nene11Le a octatc?J ultll Lne oar L.t support Ydlll ..up.I,ated lu dltetllative cupPurt svsLem, larrellLty hcle.g uaeJ af the Len,::rat 1, UI.Jlng 11-al tl. .1 a d 1 c L V h S LIdl'. L dal. I -ten- lu L he tt I .. L'., etuJ I e. 11'? L_1,1'1,11 .Jtd.. it, ..urn,at'l core ,LuJICCill JhLdll, an.: ...,La -IL .utia_tel .an LI?r oar of -l: l,.!rl .a..a. Ma terI.I auJ ...11,mc[Ii -ldla,tutcle 11. LI.ac .uwIttIca Welt a, a.. V.alte,, L.. .:Ltail, ..,,L., uI. LuClu,alug) Lelll anci ur devel?puJ I.,r Cul r1 , all. ...~.,rLrI Vt,ILt 1.'ere ~e,1C L? .Lher Gentiaii m111cc t, UL.-rye a Variety o. a rL vyl I pp.1Ca:t..n:. 'a.la IrL ..,_wLeiti, Iapl,.III ,tall ~,..:. IL all, maLertdl c1,arait-erlstIcs, JIRICn,IUIIe. and laden ul1.1 ILc rrgatrelaeuls. ,1 r.? p.'rt .a pro-1Jd, labor rep altrlarnts Jdta and illtlitI ieS tie l,ealtll d?J ,atetV ISSUC ,u-1aled Wit su furl Wall a an, CJl,wttuctSOn, I'aLentiaI appll.at1ou:. Ior support Walt, ,a,. , a, sdV.u,L111 .., u.1 retreating lungval1, single -t r-, roar al,- pi r. [,-+ln, anJ SuhIU..,Ina, Sill] b1OpplllgL ale 1:111neated aid al? e.aIWRac AS Sddemcni LV pre,C'IIL..: .,f LI. Clabllhty r+t rlul,I.,y111I? ulg4,rt .I Le.l,lwlug,. Lr i,,,rCASC Lllc rtCVLLrS rat, u., retrc.+tlnp .unui.,11? ur L., elply, A d v Ctnp IuI-,wall in uer;-!y iy1ng seam, . 11111.a1L .a1,.'iI1.-I,.. nr S.IU1tIVlil a1 milItlI; Lust, La LIldnt;2S L.~ gey support Vait Id tdmcLera la dlaa presents,.]

Jan 1, 1980

By V. B. Dale

This is one of a series of reports covering the mineral resources of the Nation. It describes briefly most of the known tungsten deposits in Yuma, Maricopa, Pinal, and Graham Counties, Ariz. Most of those described were examined by the author. An effort was made to determine the position of the various deposits by section, township, and range and to give accurate road direction to each property from a prominent landmark. All available maps have been used in making these determinations, but in unsurveyed areas it was necessary to make approximate projections of subdivisions. The township and range numbers refer to the Gila and Salt River base and meridian.

Jan 1, 1959