Search Documents

By U. W. O. L Vogler

"The behaviour of rocks depends on their material properties, and therefore it is important that these properties are determined by relevant and reliable laboratory testing methods. The ISRM Suggested Methods are very important documents in this regard, and a draft suggested method exists for the determination of the ’complete stress-strain curve for intact rock in uniaxial compression’. The method specifies the required geometry of specimens and the required testing procedures. The research described in this paper involved the determination of complete stress-strain curves for two materials, one exhibiting the Class I characteristic, and the other the Class II characteristic. To obtain a better understanding of the deformation behaviours in the post-peak region, tests were carried out on specimens of both material types with different length-to-diameter ratios. The results showed that the geometries of the test specimens influence the stressstrain curves in the post-peak region. The implication is, therefore, that the numerical values obtained for the slopes of the post-peak graphs are not material constants, but are geometry-dependent. Explanations for this behaviour are given. These findings have important implications regarding the use of post-peak data, for example for blast fragmentation considerations, and for evaluation of rockbursting potential. The research findings are based on a limited amount of laboratory testing, and should be confirmed by further testing. IntroductionThe most common approach for studying the behaviour of rock is by compression testing of cylindrical specimens in the laboratory. Rocks respond to forces by deforming and eventually breaking. The strength and the deformation characteristics are derived from the stressstrain curves produced. Standard shapes and sizes for the test specimens and standard loading rates are recommended in the Suggested Methods of the International Society for Rock Mechanics (ISRM) and the American Society for Testing and Materials (ASTM) standards. In spite of these standards, there remain certain aspects of testing which require further attention. The research described in this paper deals with deformation and failure behaviour of rock materials using stiff, servocontrolled testing equipment. The particular objective was to test the premise that the behaviour of cylindrical rock specimens in the post-peak region of the stress-strain curves does not reflect only a material characteristic, but is influenced by the height-to-diameter ratio (the geometry) of the rock specimen. An additional objective was to investigate the effect of the stiffness of the test equipment on the outcomes of tests."

Jan 1, 2016

Limestone formations in the United States can be subject to relatively high horizontal stresses due to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rockfall hazard. Rockfalls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings have an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orientating the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and offsetting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

Jan 1, 2008

By D. Lunt

This paper describes and sets in context the commercially proven uranium extraction processes. It also discusses some of the technologies that are currently being pursued with the aim of reducing costs and overcoming a number of technical issues that are faced by process designers and operators. In doing so, opportunities for the transfer of extraction technology from other industries/commodities are identified. The key processing areas that are examined include: ?The influence of mineralogy. The type of uranium mineralization and the nature of its association within a particular deposit will have a major impact on process route selection. Uranium minerals are classified according to their influence on extractive metallurgy. As the uranium price has risen in recent times, so opportunities are increasing for the recovery of uranium from less conventional resources such as phosphates and fossil fuels. ?The opportunities for employing techniques aimed at reducing the capital and operating costs of the overall process such as heap leach and beneficiation. Preconcentration by screening, gravity separation and radiometric sorting can potentially reduce the mass flow to the downstream leach and recovery plants. ?Purification or separation of uranium in carbonate systems. While it is possible to directly precipitate uranium from clarified leachate, the presence of impurities such as vanadium, molybdenum and others may dictate that ion exchange or selective precipitation is employed. Advances have been made in other industries in terms of improved ion exchange equipment aimed at reducing resin inventories and hence costs. ?Separation in acid leach systems. Earlier developments included the use of combined SX-IX systems (Eluex or Bufflex) and the introduction of continuous countercurrention exchange (CCIX). Column SX has found a ready application to uranium in view of the rapid extraction kinetics. With the renewed interest in uranium processing, efforts are being redirected towards further development of resin-in-pulp (RIP) as a means of driving down capital and operating costs. ?Extraction in a chloride environment. Australia and Namibia are desert countries where good quality water comes at a cost. However, both have access to saline water from either the ocean or subterranean aquifers. The issues associated with operating a uranium extraction operation in such environments is discussed. ?Extraction from less conventional sources. Recent price increases for U3O8 have resulted in a number of companies examining the recovery of uranium from sources such as fossil fuels and phosphate deposits. Both of these areas were examined in the 1970s and 1980s and a number of approaches were commercialized. The paper reviews the extraction options.

Jan 1, 2007

By G. Dhakal, J. -I. Kodama, K. Neaupane, T. Yoneda

ABSTRACT Durability tests and evaluation of sub-zero temperature effects to some argillaceous clastic rocks were carried out. Welded tuff, limestone, sandstone and schist samples collected from different parts of Japan were tested and results are presented. Schist and dolomite from Ganesh Himal area along the higher Himalayas of Nepal were also tested, and the results are compared. The slaking tests were performed on all samples in pure water. The results reveal that the slaking index of schist from Japan is lower than that of schist from Nepal. Regarding carbonate rocks, the slaking index of limestone from Japan is higher than that of dolomite from Nepal. A tendency of decrease in slake durability with an increase in porosity is also observed. Freezing and thawing experiments conducted on welded tuff and schist reveal that crack initiates earlier but extends slower in schist than in welded tuff. It is also observed from the freeze-thaw experiment that the welded tuff deteriorates and wears faster than the schist. However, sandstone remains relatively intact for a long run of freeze-thaw cycles. Zusammenfassung Beständigkeitstests sowie die Bewertung der Auswirkungen von Minusgraden auf Tonschiefer Trümmergestein wurden durchgeführt. Dabei wurden geschweißter Tuff, Kalkstein, Sandstein und Schiefer aus verschiedenen Gebieten Japans sowie Schiefer und Dolomitgestein aus dem Ganesh Himal Gebiet, dem höheren Himalaya Nepals, untersucht und die Resultate verglichen. Für alle diese Gesteine wurden Slaking-Tests in reinem Wasser vorgenommen. Die Resultate zeigen, dass das Slaking von Schiefer aus Japan höher als das von Schiefer aus Nepal war, wohingegen bei kalkhaltigem Gestein das Slaking von Kalkstein aus Japan niedriger als das von Dolomitgestein aus Nepal ausfiel. Es wurde dabei auch eine Tendenz zur Löschbeständigkeitsverringerung bei gleichzeitig erhöhter Porosität beobachtet. Gefrier- und Tautests an geschweißtem Tuff und japanischem Schiefer zeigten, dass Risse in Schiefer schneller auftraten, aber sich langsamer ausweiteten als in geschweißtem Tuff. Bei Gefrier- und Tautests wurde ebenfalls beobachtet, dass geschweißter Tuff schneller verfällt und verschleißt als Schiefer. Sandstein hingegen blieb über lange Tau- und Gefrierzyklen intakt Résumé Des tests de solidités et l’évaluation de l’effet des températures en dessous de zéro sur les rocs argileux ont été effectués. Les rocs d’origine volcanique (cendre), les rocs calcaires, sableux et les schistes de différentes régions du Japon, ont été étudiés. Les schistes et les dolomites de la région de Ganesh Himal le long du haut Himalaya (Népal) ont été étudiés et comparés à ceux du Japon. Les tests de désintégration sur les rocs ont été effectués dans l’eau pure. Les résultats montrent que l’index de désintégration des schistes du Japon est inférieur aux schistes du Népal. En ce qui concerne les rocs carbonyles, l’index de désintégration des rocs calcaires du Japon est supérieur à ceux des dolomites du Népal. Une décroissance de la résistance à la durabilité est observée avec une plus grande porosité des rocs. Les tests de congélation-décongelation sur les schistes et les rocs d’origine volcanique (cendre) du Japon montrent une apparition précoce des fissures mais l’expansion des fissures est plus rapide dans les rocs volcaniques. Des tests similaires montrent que les rocs volcaniques (cendre) se désagrégent plus rapidement que les schistes. Cependant, les rocs sableux restent intacts après plusieurs cycles de congélation-décongélation.

Jan 1, 2003

By R. S. J. Toit

Discussion: T. L. Gibbs,* (Honorary Vice-President and Fellow): In terms of the Pneumoconiosis Compensation Act of 1962, a Pneumoconiosis Risk Committee was established whose function it is to estimate (by whatever means the committee deems fit) in respect of every controlled mine the pneumoconiosis risk to which persons employed in a dusty atmosphere at that mine are exposed. In estimating such risk the committee may estimate different risks in respect of individual mines or parts of mines or classes or groups of mines or occupations or localities at mines. The pneumoconiosis risk may be reviewed and re-estimated at any time. The Act provides further that the General Council for Pneumoconiosis Compensation shall apportion the levy imposed on owners of controlled mines on the basis of the pneumoconiosis risk determined by the risk committee and the numbers of persons employed in a dusty atmosphere. The task of the risk committee is a most responsible one and also a very difficult and complex one in view of the many different types of mines, rock formations, dust conditions, etc. Quite obviously, comparisons between mines cannot be made on dust concentrations alone as different mineral dusts have different toxicity or pneumoconiosis response factors. However, with its present knowledge, the risk committee is satisfied that the risk at mines, other than coal mines, is related to the mean quartz-equivalent dust concentration to which persons are exposed and the estimation of risks is based on this relationship. From the above, it will be clear that the work done by Dr du Toit on the problem of basing the current rate of levies to provide for pneumoconiosis compensation on the current dust hazard at mines has been of immense value to the risk committee. Up to now the risk committee has not been able to obtain complete and accurate information on the dust exposure of persons at all mines - and, in fact, it is doubtful whether it will be economic or practicable to obtain this in the foreseeable future - but reasonable assessments have been possible from routine dust sampling in some cases and from periodic comprehensive dust surveys in others. As a temporary measure the risks of some mines were estimated initially on a group basis relating to average dust conditions and the type of rock and mineral mined, but as more information became available, differentiation between individual mines became possible. It is the aim of the risk committee to eventually apply such a differentiation in all cases and to ensure that within the bounds of practicability each mine pays for its risk and for its risk only. In this connection, the relationship between the levies and the amounts actually paid out in compensation are examined regularly. In conclusion, I wish to add my congratulations to the author on his excellent paper. His findings will assist materially in the just administration of that very important piece of beneficial legislation, the Pneumoconiosis Compensation Act. G. K. Sluis Cremer MD (Visitor): Dr du Toit has made a valiant attempt to relate dust hazard and the rate of collecting funds for the purpose of paying compensation for Pneumoconiosis. In doing so he has had to make a number of assumptious, some of which touch on the medical aspects of pneumoconiosis. It is worth discussing whether these assumptions are justifiable. Pneumoconiosis is defined in our Pneumoconiosis Act as permanent disease of the cardio-respiratory organs which is caused by the inhalation of mineral dust. To a non-medical person this definition has probably a clear cut meaning. The doctors however have to deal with such conditions as silicosis and asbestosis where there is a well defined dose response relationship to the inhalation of quartz and asbestos respectively and on the other hand chronic bronchitis where the relationship to dust inhalation is poorly defined and where certainly no clear dose response relationship has emerged after many investigations in this country and overseas. Nevertheless since 1953 about half of our certifications for Pneumoconiosis are on the grounds of chronic bronchitis i.e. the X-rays show no evidence of silicosis, asbestosis or other relevant disease. This fact must affect Dr du Toit's computations. The next assumption we should examine is the manner in which toxicity factors have been allocated to the various mineral species. These allocations have in part been based on a restricted number of animal experiments carried out overseas but mostly in South Africa by Webster at the Pneumoconiosis Research Unit. To extrapolate the findings in a relatively small number of animal experiments to the expected reactious in man is a notoriously dangerous exercise. Furthermore the bracketing together of all silicates (except asbestos) and the insoluble metal oxides is entirely unacceptable. Talc (a hydrated silicate of magnesium) and muscovite mica (a silicate of aluminium and potassium) cause pneumoconiosis in their own right. On the other hand

Jan 3, 1970

By F. M. Ramadhan, M. R. Pratama

Monitoring open-pit mine road conditions has become very critical nowadays. There are several benefits to in conducting research on this field such as opportunity to improve truck’s speed which directly influences truck’s productivity. This research aims to provide a semi real-time, and sensors-based automatic road damage detector that predicts the road quality through road damage exact location tracing, road damages auto-classification, and real-time instruction in the form of work order format to mining road maintenance, and repair authorities through mobile apps and maintenance unit’s in-cabin display. It will also provide the maintenance/repair activity performance evaluation via integrated dashboards. The artificial neural network algorithm is applied during the process of data training regarding classifying road damages and severities which resulted in a valid model. The road damage classification model has a precision level of 80.5% in predicting whether the road is damaged or not. Using this approach, we are expecting to visualise a road quality map of all active roads on mine site.

Sep 1, 2021

By R. Letsaole, H. Mabowa, J. Sehat, J. Tshilongo, T. Rampfumedzi, N. Ntsasa, A. Mkhohlakal1

This study explores the use of co-collectors to enhance the recovery and determination of rhodium during fire assay with lead collection, followed by acid dissolution using conventional hot plate methods. Rhodium, a critical platinum group metal, poses analytical challenges due to its low natural abundance and complex chemistry. Among the co-collectors tested, palladium and tellurium demonstrated significantly improved rhodium recoveries, ranging between 100% and 120%, whereas silver resulted in poor recovery and higher error margins. These findings highlight that co-collectors can enhance the efficiency and sensitivity of platinum group metal analysis, although their effectiveness is dependent on the chemical interaction with the target element. Acid dissolution was essential to ensure complete digestion of prills prior to analysis, enabling accurate quantification of rhodium. Overall, the findings suggest that palladium and tellurium are effective co-collectors for rhodium determination in fire assay, while silver and lead flux alone are unsuitable. This work provides important insight into optimising fire assay procedures for reliable rhodium analysis, with potential benefits for platinum group metals recovery and economic evaluation.

Mar 6, 2026

By N. Morris

In South Africa, diamonds are mined predominantly in rural areas. Kimberlitic diamonds dominate in Limpopo and the Northern Cape Provinces whereas alluvial diamonds are mainly sourced from the North West and Northern Cape Provinces. There are a few large and medium sized diamond companies (De Beers, Petra Diamonds, Trans Hex, Rockwell and Alexkor). There are many smaller companies involved in diamond mining, mostly alluvial diamond mines. The nature of alluvial diamond deposits is that they are aerially more extensive and thus their surface impacts are more pervasive: The recent downturn in diamond prices has resulted in the sudden cessation of mining at many small and medium diamond operations. The South African Mining Charter requires all mines, including diamond mines, to subscribe' to .the following empowerment objectives:

Jan 1, 2010

By J. H. van Laar, L. J. van der Walt, P. L. Crouse, H. Bissett, G. J. Puts

"SynopsisSilicon carbide nanopowders were produced using a microwave-induced plasma process operating at 15 kPa absolute and at atmospheric pressure. Methyltrichlorosilane (MTS) served as precursor, due to its advantageous stoichiometric silicon-to-carbon ratio of unity, allowing it to act as both carbon and silicon source. Argon served as carrier gas, and an additional hydrogen feed helped ensure a fully reducing reaction environment. The parameters under investigation were the H2:MTS molar ratio and the total enthalpy. The particle size distribution ranged from 20 nm upwards, as determined by SEM and TEM micrographs. It was found that an increase in enthalpy and a higher H2:MTS ratio resulted in smaller SiC particle sizes. The adhesion of particles was a common occurrence during the process, resulting in larger agglomerate sizes. SiC layers were deposited at 15 kPa with thicknesses ranging from 5.8 to 15 µm.IntroductionIt is well known that methyltrichlorosilane (CH3SiCl3 or MTS) decomposes to form silicon carbide (SiC) and hydrogen chloride (HCl) as shown in Equation [1]. The reaction kinetics and mechanisms for this reaction are thoroughly reported in the literature (Sone et al., 2000; Papasouliotis and Sotirchos, 1999; Kaneko et al., 2002; Wang et al., 2011)."

Jan 1, 2015

By K. Dewar

The catalytic converter industry is composed largely of global multinational manufacturers who supply to vehicle manufacturers (original equipment manufacturers ? OEMs) from facilities strategically located internationally, including plants in South Africa. The South African catalytic converter production facilities were established at the request of the OEMs and commenced manufacture in the early 1990s. This near 100 per cent export focused industry exists in South Africa because of the incentives offered by the Motor Industry Development Programme (MIDP), which ultimately provide the OEM with import duty rebates. The South African catalytic converter industry is a complex vertically-integrated supply chain with a local content in excess of 85 per cent, substantially more than any other exported automotive component. The industry remains one of the very few downstream manufacturing industries where South Africa has a significant global footprint. This is even more important when it is considered that this industry is the key end-user for two of South Africa?s most important mineral resources, namely platinum group metals (PGMs) and chromium, and is in an industry which will see massive global growth as the developing nations of the BRICs grow their auto industries. In over 15 years of existence in South Africa, the catalytic converter industry has achieved remarkable growth, averaging compound growth in the region of 14 per cent per annum. The industry is the highest contributor to automotive component export revenue. South Africa holds >8 per cent% of global PGM reserves. During 2011, South Africa supplied 59 per cent, 29 per cent, and 72 per cent of the global demand for platinum, palladium, and rhodium respectively, as well as over 50 per cent of the global chromium demand. Global autocatalyst production remains the largest consumer of PGMs, and South Africa alone beneficiated 15 per cent of locally mined PGMs in the production of catalytic converters ? all is converted from PGM sponge (powdered metal) into PGM solutions for coating onto catalysts. Beneficiation of PGMs also takes place via the production of jewellery and electronic goods; but compared to catalytic converters, this volume is negligible. The industry is also the largest consumer of locally produced stainless steel (>50 000 t/a), exceeding 38 per cent of local consumption. The industry is a substantial generator of highly skilled employment, with over 5 000 direct jobs (excluding OEMs and stainless steel manufacture) and an estimated more than 30 000 indirect jobs resulting from upstream and side-stream suppliers. The industry places a high focus on skills transfer and development, with all companies providing high-tech training and education both locally and overseas. The industry has invested in excess of R5 billion in plant, equipment, people development, and process development over the last 15 years to support transfer of production and new technologies to South Africa. This has resulted in significant skills development in the support industries as well as within the catalytic converter industry. The current projections for local PGM beneficiation via catalytic converters reflect a downward trend as a result of production being moved to other global locations due to uncertainty around changes to government incentive programmes. The industry is currently capacitated to support 23.7 million units per annum. During 2011 it utilized about 70 per cent of this capacity, but forecast projections suggest that this will be at 46 per cent of this level by 2016. At full capacity the industry would represent 19 per cent of global autocatalyst production compared with the current 13 per cent in 2011. The industry believes that there is potential to make South Africa the preferred location for catalytic converters worldwide, given suitable support from the mines and Government.

Jan 1, 2012

By C. van der Merwe, R. Lumbule, J. Kgomo

"The mining industry in the Democratic Republic of Congo has seen a significant expansion in copper and cobalt production in recent years. The greater proportion of this expansion has arisen through processing of oxide ores. The design of metallurgical processes for these oxide ores is based on the conventional equipment and layout for processing of sulphide ores, and comprises milling followed by leaching, solvent extraction, and electrowinning. The physical characteristics of the oxide ores, however, provide the process design engineer with an opportunity to examine critically the principles on which equipment selection is based and to design processes better suited to these ores. In 2015, ERG Africa began a project to expand the leaching capacity of the Luita hydrometallurgical facility. A number of innovative changes to the conventional process design were included in the modified flow sheet, which were validated when the project reached design throughput in November 2017. Of these changes, the most novel presented an alternative approach to mitigate the impact of colloidal silica on the operation of the solvent extraction plant. Introduction ERG Africa operates the Luita hydrometallurgical facility located at Kakanda in the Democratic Republic of Congo (DRC), treating malachite and heterogenite minerals to recover copper as electrowon cathode and cobalt as a hydroxide precipitate. The process was originally conceived as a heap leach operation followed by direct electrowinning of copper, with solvent extraction (SX) and electrowinning (EW) of cobalt. In preparing the sized ore for the heap leach operations, the undersized ore fraction at a P80 of 625 µm was discharged to a fines storage facility for later processing. This fraction carried with it approximately 30% of the copper contained in the run-of-mine (ROM) ore feed, and an equivalent proportion of cobalt.In a subsequent development, the cobalt SX section was converted to a copper SX facility, the leached cobalt being recovered from a bleed stream from the copper heap leach circuit. The operating cost for the process as then installed placed this facility well in the fourth quartile of the industry cost curve. The initial Luita operation was established in 2010 at a time when metal prices were above long-term averages (copper above US$3.00 per pound; cobalt above US$20.00 per pound), and the drop in prices in 2015/2016 presented a major challenge. The London Metal Exchange (LME) copper price dropped below US$2.00 per pound, with cobalt dropping below US$10.00 per pound in Q1 2016. This set in motion a range of improvement initiatives for the Luita operation. Central to this was the installation of a tank leach circuit to process the discarded fines and a modified SX circuit to manage colloidal silica. The revised Luita circuit reached design capacity in November 2017 and has proven to be well suited to processing of the oxide ore feed. This process design challenges the boundaries of conventional thinking in the areas of leaching, solid/liquid separation, solution management, impurity management, and metal recovery, and is the subject of this paper."

Nov 1, 2018

By A. J. Dickson, A. M. Starfield

This paper reviews the progress made to date in the development of computer models of heat and moisture transfer from rock surfaces to the ventilating air in deep-level mines. The application of these programs to ventilation planning and design is discussed.

Jan 1, 2014

By Willie Hefer

Contents ?Purpose ?Introduction ?Deviation of bias results ?Operational correctness ?Maintenance and Costs ?Conclusion ?Acknowledgements

Jan 1, 2005

By R. Rubin, P. A. Laxen, G. S. M. Becker

An account is given of developments in the use of activated carbon for the recovery of gold from cyanide solutions. The carbon-In-pulp process employed at the Homestake Mine is described, and its various applications in South Africa and their effectiveness are discussed. Probable future work on the carbon-in-pulp process and other possible applications of carbon for the recovery of gold are outlined.

Jan 1, 1979

By A. Morley

It is difficult to evaluate exploration properties in a manner that is transparent, repeatable and easily re-calculated to cater for different geological interpretations, but the risk-based assessment methodology, the Geological Risk Method, developed and described by Lord et al (2001) attempts to satisfy all these criteria. This paper examines a case study example based on valuations of exploration projects conducted by SRK Consulting using this methodology, and describes some of the advantages and limitations of the method.

Jan 1, 2007

By Allan Jansen, Robin Bissett

[Power-Point Presentation]

Jan 1, 2005

By Gernot Beer, Christian Dünser, Marcos Noronha

The main findings of the joint research initiative “Numerical Simulation in Tunnelling” and a follow-on project on efficient numerical simulation models for tunnelling are presented. Die wichtigsten Resultate des Forschungsschwerpunkts „Numerische Simulation im Tunnelbau“ und einem Folgeprojekt über effiziente numerische Simulationsmethoden werden präsentiert Les résultats les plus importants du point principal de la recherche "simulation numérique dans la construction de tunnels" et un projet consécutif sur des méthodes de simulation numériques efficaces sont présentés

Jan 1, 2003

By G. E. Blight

The load-compression characteristics of mine supports are usually evaluated by means of relatively rapid tests, whereas in the mine they are subjected to much slower strain-controlled compression. The effects of slow strain rates on the load-bearing properties of mine supports were explored by means of straincontrolled tests on model timber packs and timber-filled steel telescopic props. It is shown that the load-compression characteristics of these supports are considerably influenced by the rate at which they are compressed. The species of timber influences the behaviour, but to a relatively minor extent. Preloaded supports are shown to lose a significant proportion of their preload by relaxation.

Jan 1, 1978

[COUNCIL FOR 1992/93 President J.P. Hoffman President Elect Dr H. Scott-Russell Vice Presidents Senior J.A. Cruise Immediate Past President R.D. Beck Junior D.A.J. Ross-Watt Honorary Treasurer J.A. Cruise Members of Council Dr N.A. Barcza B.R. Broekman G.A. Brown P.M. Craven Prof. R.J. Dippenaar J.R. Dixon* A.A.B. Douglas B.R. Fleetwood Dr R.V.R. Handfield-Jones P.R. Janisch * co-opted P.J. Knottenbelt R.P. Mohring J.L. Nel* K.C. Owen P.D.K. Robinson K.A. van Gessel D.J. van Niekerk C.J.C.J. van Vuuren* P.M.T. White]

Jan 1, 1993

By P. Michalcik, V. Petros, M. N. Bagde, K. Holub

The objective of this paper is to present some results of laboratory experiments during the investigation of stress-strain characteristics of Carboniferous sandstones at dynamic loading. During these experiments increasing frequency and the constant amplitude of dynamic loading and/or constant frequency at different amplitude of dynamic loading were applied. Der Gegenstand dieses Artikels ist, irgendeine von Ergebnissen von Laborexperimenten bei Messung der Spannungs- und Deformationscharakteristik der Karbonsandsteine bei ihrer dynamischen Belastung vorzustellen. Im Laufe diesen Experimenten wurden entweder anwachsende Frequenzen bei konstanter Amplitude der dynamischen Belastung, oder gleiche Frequenzen bei variabler Amplitude der dynamischen Belastung verwendet. L'objectif de ce papier est présenter quelques résultats d'expériences de laboratoire pendant l'enquête de caractéristiques de la tension – deformation de grès Carbonifère à sollicitation dynamique. Pendant ces expériences fréquence croissante et l'amplitude constante de sollicitation dynamique et/ou fréquence de la constante à amplitude différente de sollicitation dynamique ont été appliquées.

Jan 1, 2003