Search Documents

By Y. Jin

Magnesia ramming materials have been widely used in China instead of magnesia bricks as furnace lining materials of ferroalloy refining furnace. The paper introduces the development of the ramming material, recounts its chemical composition, physical property and application characteristics. Because of its high MgO contents and fine sintering property, the ramming furnace bottom has the properties of good refractory, monolithic construction and thermal shock resistance. The changes in mineral composition and furnace tearout characterization show the reasons for the bottom?s long service life. The obvious benefits are widely achieved, the annual saving cost in refractory is about 2 millions US dollars.

Jan 1, 2004

Konkola No 3 shaft experienced severe mining-induced stress and time-related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

By S. P. Pereira

The mechanized mining cycle using loaders and shuttle cars had its peak in terms of usage in the mining industry during 1950 through 1960. In Brazil, this system is still used at underground coal mines in southern Santa Catarina coal basin. With the aim of investigating the benefits of a new mining scheme using the room and pillar method for these local mines, a computational simulator model was developed in order to investigate the mining cycle. This paper presents the methodology used to develop the simulator and the results that the simulation shows regarding impact of the proposed new scheme on mining productivity.

Jan 1, 2012

By J. J. Stacey

Large mining companies generally follow the distributed ownership corporate model, with a board of directors responsible for decisions that affect both shareholder value and stakeholders of the company. The board is simultaneously responsible for setting the culture and values of the corporation, which drive performance and priorities. Companies listed on the Johannesburg Securities Exchange (JSE) commit to sustainable development in various ways, either by virtue of implementing the King Code of Governance 2009 (King III) and/or through their own public reporting on social and environmental matters. Many mining companies make public statements regarding their support for environmental stewardship, ethical behaviour, and fair treatment of communities. It is a local, regional, and indeed, global phenomenon that companies fail to deliver on these statements. Research was carried out through the Institute of Directors of Southern Africa in 2007, and followed up in 2012, regarding directors? understanding of sustainable development issues, the relative priorities, what is needed for ?radical change? to effect sustainable development, and what enables or constrains the latter. Pertinent findings of both surveys are presented in this paper, and it is suggested that ?on-the-ground? performance may be indicative of the nature of leadership and decisions in the topmost ranks of the company. The results indicated that environmental concerns fall consistently below social issues. Financial capital ranked most important, and while environmental issues are recognized as being of strategic concern for the long-term, they ranked as being the lowest importance of all ?Five Capitals? (Financial, Manufactured, Social, Human, and Natural). Social capital ranked second lowest, with black economic empowerment being the only high-priority social issue. There is also evidence that certain companies within the mining sector fail to recognize their absolute dependence on natural resources. Much is made in academic and popular literature of the need for a new type of leadership for the radical shift to sustainable development: at company level this implies therefore a new type of director. The research found that only 14 per cent of directors felt that board decisions are consistent with their personal values; while intentions are strong to behave ethically and serve sustainable development, actions to give effect to these intentions lag significantly. Respondents indicated that the top impediments to courageous leadership for sustainable development related to personal issues of maintaining the image of being a director, fear of appearing weak, fear of being a lone voice, and bowing to board-colleague peer pressure.

Jan 1, 2014

Sishen Iron Ore Mine previously used only A-grade material (>60% Fe in situ value) from the pit for beneficiating in the DMS plant to a final product grade of 66% Fe in lump and 65% Fe fine ore. The B-grade (between 50% and 60% Fe) and C-grade material (between 35% and 50% Fe) were stockpiled separately, owing to the inability of the existing DMS plant to beneficiate material at densities higher than 3600 kg/m3. The ability to beneficiate the B-grade material at densities higher than 3600 kg/m3 was evaluated, and air-pulsed jigs were found to be techno-economically feasible and value maximizing. The beneficiation of B-grade material would add to the existing DMS production of 28 Mt/a, with no additional mining cost and only limited costs for the handling of waste and B-material. The objective of the Sishen Expansion Project (SEP), i.e. the jig plant, was to produce 10 Mt/a of saleable product with six modules to the set physical and chemical specifications by 2009. During the start of construction, it was decided to add another two jig modules to the plant to increase production to 13 Mt/a. During commissioning and ramp-up the shortcomings and advantages of the jigs were fully experienced and understood, resulting in many changes to optimize jigging performance..

Jan 1, 2014

By A. H. Onur

Many factors govern the size and shape of an open pit, and these must be properly understood and used in the short and long-term planning of any open pit and quarrying operation. The importance of each factor will depend on the particular project, but the geology, grade, and localization of mineralization, extent of the deposit, topography, property boundaries, production rates, bench height, pit slopes, road grades, mining costs, and cut-off grades are key elements of open pits. This paper discusses the work done on the above parameters in order to provide an optimal production plan for a limestone quarry and clay deposits that provide raw material for a cement factory in Turkey. Soke cement factory has 1 400 000 tons of clinker capacity and is located on the western part of Turkey, in the province of Aydin. It is one of the largest facilities in the cement sector in terms of capacity, and it has a large advantage over facilities because the location of the factory was chosen to obtain the raw materials necessary for cement production within very short distances. However, the old reserves that supplied limestone to the factory had been reported to have run out, and therefore new limestone reserves in the same province have been investigated over the years by experienced geologists. From surface samples, high MgO content was reported in the neighbourhood of limestone formations with high dolomatization; hence, other alternatives were taken into consideration. One alternative with better chemical composition had been found 24 km away from the factory, but the haulage cost of limestone was unacceptable for the factory due to high diesel prices in Turkey. The maximum allowable MgO content in the pre-mix feed to a rotating furnace is 2.5% MgO content in pre-mix from both limestone and clay deposits. The clay deposits belonging to the cement factory have higher MgO content than the limestone deposit, and therefore this quality problem was taken into consideration first, instead of transporting material from 24 km away. This study gives the details of work done to evaluate both the clay and limestone deposits, statistical analysis performed on core samples taken from drill holes, mathematical modelling for both sites, and most importantly of all, in-pit homogenization work that reduced the pre-mix MgO content. As a result of this study, the profitable limestone quantity has been improved in order to serve the cement factory over a projected 25 additional years without using any material from the close deposit.

Jan 1, 2008

By W. D. Northrop

This paper gives an account of the development of a technique whereby the vertical limits of geological horizons may be identified by the use of vertical variograms on the mineral of economic interest. This information may supplement or guide the correct subdivision of the individual horizons into meaning full data sets by diligent geological observation. This process then improves the quality of the variance modelling of the gold distribution in the plane of the individual layers and therefore enables better estimates to be made into the grids or blocks of the mine model. The technique is explained by an account of the development work, which was performed, on duplicate superimposed reef horizons in the Kimberley formations. The paper then shows how the correct approach was developed to evaluate the mineralized layers in a multiple stacked conglomerate layer sequence in the Elsburg reefs of the Witwatersrand Rand System at the Target deposit. The method of categorization of resources according to confidence in the estimate is also explained. The feasibility processes carried out on the three-dimensional model, in accordance with the SAMREC code are also described. An example of the development of a reconciliation process utilizing chip sampling is also explained.

Jan 1, 2003

By B. P. Watson

Crush pillars have been incorporated into a mechanized, low-profile trackless system at South Deep Gold Mine. These pillars had to be designed to fail near the face and to ensure that pillar failure is contained within the pillar, to avoid bursting and the risk of high loads being generated during a seismic event, respectively. PoweRite backfill bags were recommended to maintain the integrity of the pillars; except in the main access drives, where the sidewalls were to be supported on 5.6 mm diameter weldmesh and yielding anchors. The results of a trial site investigation exceeded expectations, showing a residual pillar strength of about 37 MPa for a newly formed pillar and 8 MPa for a pillar subjected to seismicity and a closure of more than 300 mm. The introduction of these pillars has improved the rock mass conditions because of the active nature of the support, compared to the previous passive backfill method. Importantly, the pillars have increased mining efficiencies and improved face availability. A potential cost saving to the mine of R140.9 million could be realized over a period of 10 years.

Jan 1, 2014

By J. E. Davidsen, M. Honstad

"A well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. A worn or short tap-hole channel can lead to more violent flow, significantly increasing the fume emissions during tapping and leading to more metal being mixed with and lost to the slag. Over time, a worn tapping channel might cause side channels and damage to the lining around the tap-hole area. This can result in a burn-through which is a considerable safety risk and will cause significant production losses. At Eramet Norway Porsgrunn, tap-hole maintenance has been done regularly with electrode paste for over three decades with good results. This article summarizes some of the experiences obtained from this practice on a 33 MW SiMn furnace, as well as a change to a coal tar pitch-free binder. IntroductionA well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. Metal and slag are regularly tapped from the furnace and may cause a lot of wear on the tapping channel, increasing the risk of lining damage and ultimately leading to a burn-through. On furnace 10 at Eramet Norway Porsgrunn, the tap-hole area is the part of the lining that has been by far the most prone to burn-through since the startup of the furnace.Experience shows that almost all lining problems have started with burn-through in the tap-hole area or in close proximity to the tap-hole. During tap-hole repairs, side channels with metal and slag have also been observed emanating from the main tapping channel. In addition, a shorter tapping channel will cause more violent flow. This can lead to more metal droplets being entrained in the slag, and increase the risk of the furnace not being closed properly at the end of the tap.As a burn-through is a considerable safety risk, and also causes significant production losses, systematic work has been performed over the years to maintain the tapping channel in order to prevent burn-through."

Jun 1, 2019

By T. G. Carter

Support system design for tunnels and underground excavations has for many years relied heavily on the use of rock mass classification systems and the Hoek-Brown failure criterion as a means for characterizing rock mass behaviour. Because of their development, both the GSI system and the Hoek-Brown criterion admirably characterize most ?normal? rockmasses from the viewpoint of their behaviour for rock excavations. They, however, run into difficulties when applied at the two ends of the rock competence scale. This is largely because block size and incipient strength are such that rockmass behaviour in these domains tends not to be controlled by interblock shear strength but rather by material strength. At the low end of the rock competence scale (UCSi <<15 MPa and GSI generally <30) discontinuities play less of a role and rock mass strength tends to matrix strength. Similarly, at the high end of the scale (GSI >>65, mi>>15), because discontinuities are now widely spaced, block size becomes so significant that again, intact material behaviour rather than the fracturing becomes the dominant factor controlling rock mass strength. In this paper several case examples are presented to illustrate the application of the high-end (spalling) and low-end (weak ground) transition Hoek-Brown relationships proposed by Carter, Diederichs and Carvalho (2007) as a basis for better defining rockmass behaviour at the extreme ends of the rock competence scale.

Jan 1, 2008

By R. M. Goktan

Point-attack picks are one of the most widely used tools for the mechanical excavation of rock and coal. In the literature, some practical formulas have been developed to estimate their performances under varying cutting conditions such as the pick geometry, cutting depth and cutting geometry. In this study, it is shown that Evans?s theoretical model, the most cited in the literature, has serious limitations concerning the changes in the cutting geometry. Analysis of the two independent full-scale linear rock cutting experimental data reveals that both his theory and its recent modification can not fully explain the mechanism of rock breakage under asymmetrical attack. The cutting force predictions made by employing such models are shown to be too significantly weak to be of any service in practice. In this study, a semi-empirical approach was followed by means of which cutting forces under varying cutting geometries could be made. By analysing the full-scale rock cutting test data, prediction equations of the peak cutting force and mean cutting force have been developed. Comparisons of laboratory determined and predicted force values indicate that the suggested prediction equations are applicable to quite different rock materialsm which have uniaxial compressive strength in the range of about 30?170MPa, and valid for different cutting geometries. It is also shown by regression analysis that the established prediction equations are statistically significant.

Jan 1, 2005

A new method, localized uniform conditioning (LUC), was proposed in 2006 for modelling grades of small blocks of ore when data spacing is too broad for their accurate modelling by the linear regression based techniques, such as kriging (Abzalov, 2006). It represents a modified uniform conditioning (UC) technique that calculates the grade distribution functions for the large panels. LUC uses partitioning of the panels onto the small blocks and then ranks them in increasing order of grade. Based on the block ranks, a single grade value can be deduced for each block from the UC model of the gradetonnage relationships of the corresponding panel. After being first presented in 2006, the LUC method has been implemented in ISATIS© (commercial software) and became one of the common approaches for grade estimation when data spacing is broad in comparison with the estimated block size. Several years of study on the LUC method and its application to different geological environments, have allowed identification of the strengths and weaknesses of the method, which are as follows: ? The method produces accurate grade-tonnage functions, which are in a good accordance with a volume-variance relationship principles ? An initial ranking of the selective mining unit (SMU) blocks can be made by direct kriging from the sparse data grid. Therefore, the LUC method can be particularly useful at the early stages of exploration and mining project evaluations when sparsely distributed data is often the only available information ? Accuracy of the local estimation depends on the SMU ranking techniques. When ranking performed by direct kriging of the SMU blocks their spatial distribution is approximate. When the variogram of the studied variable is characterized by a large nugget effect, the block ranks produced by kriging can significantly differ from their ?true? distribution ? Block ranking can be improved using auxiliary data, either geophysical or geochemical. This allows use of the LUC method for integrating different data sets. In particular, LUC can be used for grade control in open pits by integrating resource definition data (e.g. drill-hole assays) and blast-hole assays. The latter are used for the block ranking.

Jan 1, 2014

By W. H. Holtzhausen

The purpose of this project was to compare two underground, batch coal haulers ? battery haulers and shuttle cars ? in order to determine the more viable machine to implement. The specific standards for battery haulers were investigated and compared to the requirements of shuttle cars in order to identify the unnecessary expenses related to the legal requirements that are attached to the machines. Costs such as running costs, capital costs, and maintenance costs were researched and compared over a typical life of machine. Average production rates and breakdown times were obtained and used to determine which machine would be more reliable in achieving the required annual production.

Jan 1, 2014

By W. Mackenzie

The development of a resource project inevitably requires the investigation of a vast range of issues across most engineering disciplines - mining, metallurgical, chemical, civil, electrical, mechanical and environmental - as well as the geosciences. It is also a characteristic feature of the resource industry that no two orebodies - and hence no two development projects - are the same. So these technical issues have to be addressed to a greater or lesser extent in evaluating any resource project&apos;s development potential. Not surprisingly then, technical issues tend to predominate when assessing the development potential of a project in the process typically referred to as `doing a feasibility study&apos;. But the principal purpose of a `feasibility study&apos; is to determine whether a development opportunity makes good business sense, not just whether it is technically possible. Resolution of technical issues is often seen as the primary focus of a feasibility study, whereas in reality, these technical issues are the basis upon which an asset delivery and business plan is built. This is not to say that technical issues are unimportant - they are a prerequisite to the demonstration of a project&apos;s viability. The feasibility study process must therefore demonstrate that not only have the technical issues been satisfactorily addressed, but also that the broader commercial, economic and social issues have been considered in the development of a comprehensive business plan, which includes an assessment of the risk-reward profile of the proposed development. This paper will present a framework for the conduct of `feasibility studies&apos; and provide guidance to minimum standards and best practice.

Jan 1, 2007

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

As the world continues to face the turmoil of the economic environment, legislative prerequisites and physical conditions the intervention of technological development is vital for the continuation of the ancient source of revenue: mining. The Palabora underground mining project is a state-of-the-art shaft mining system that will prove to be a benchmark in its field for years to come. An integration of modern technology?both in application and development?has resulted in a shaft system that is intrinsically holistic. Every aspect of the mining and production process has undergone thorough investigation, simulation and innovation to ensure that every component is selected by design and not simply conforming to past practice or trends. The process philosophy includes proven technology such as to promote the lowest operating cost and process time with the highest yield. The underground mining system is in the final stages of commissioning and will shortly be producing a nominal 30 000 tons per day with a predominantly automated system. This paper discusses the complete state-of-art shaft system developed for the Palabora underground mine, and refers particularly to the headgear, the winders, the conveyances and the shaft guide system, as well as the loading system developed specifically for the high performance requirements of the mine.

Jan 1, 2000

By A. M. Milev

A stand-alone instrument especially designed for recording strong ground motions was used in this study to create a large data base of peak particle velocities measured on stope hangingwalls. A total number of 58 sites located in stopes mining the Carbon Leader Reef, Ventersdorp Contact Reef, Vaal Reef and Basal Reef were monitored. The peak particle velocities were measured at the surface of the excavations to identify the effect of the free surface and the fractures surrounding the underground mining. From the monitoring results obtained, the velocity criterion of 3 m/s will bean adequate value that support systems have to sustain during a rockburst in most cases. However, PPVs in excess of this criterion were recorded, and some PVDs were damaged or irretrieveable, a consequence of which was that possible extreme events were not recorded. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response, defined as the ratio of the measured peak ground velocity to the peak ground velocity inferred from the mine seismic data. The site response measured at all mines studied was found to be 9 ±3 times on average. Values of the site response did not vary significantly with seismological parameters such as peak ground velocity, hypocentral distance and source radius.

Jan 1, 2005

By T. Watanabe, S. Hayashi, M. Hayashi, K. Nagata, H. Fukuyama

Chemical states of fluorine in CaO-SiO2-CaF2glasses in a composition range of CaO/SiO2=0.5?1.3 and 5?25 mol%CaF2have been investigated by 19F solid-state NMR with and without MAS. The isotropic chemical shifts of the glasses are close to those of cuspidine crystal (59.4 and64.3 ppm with respect to C6F6) and CaF2crystal (58.6 ppm). The fluoride ions are coordinated with four or less than four calcium ions in this composition range. The chemical shifts move to the lower frequency with an increase in the CaF2content, whereas those are not affected by theCaO/SiO2ratio. The ionic distance between calcium and fluoride ions increases with an increase in the CaF2content. The chemical state of fluorine is not disturbed by the degree of polymerization of the silicate network. Comparing the MAS and static NMR spectra, the second moment attributed to 19F-19F dipole-dipole interaction has been estimated. The values of the glasses range over 3.1?7.3107Hz2andthose are larger than the calculated value of cuspidine crystal. This indicates that fluoride ions form Ca-F clusters in the glasses and that the size of clusters increases with increasing the CaF2content. Keywords: chemical state of fluoride ion, CaO-SiO2-CaF2glass, solid state 19F NMR spectroscopy

Jan 1, 2004

The aim of this investigation was to study the influence that varying production rates have on iron sinter quality. This was done by performing sinter pot tests at different pressure drops over the sinter bed, namely 11 kPa and 15 kPa (for 500 mm total bed depths). During each of the sintering processes temperature-time profiles were recorded of the top, middle and bottom layers of the sinter bed. On completion of the sinter process the sinter cakes were divided into top, middle and bottom layers. The physical properties of each layer were subsequently characterized by performing a tumbler test and a sieve analysis. A comprehensive mineralogical study was also conducted on each layer. This study revealed that sinters of similar cold strength could be produced under the examined production rates. However, a higher production rate was accompanied by an increased amount of fines. The cold strengths of both sinters significantly increased from the top layer to the bottom layer of the sinter bed. This strength variation is not related in any simple way to the phase composition. Keywords: Sinter, sinter bed, production rate, phase composition, cold strength, tumbler index, sieve analysis, temperature-time profile

Jan 1, 2003