Search Documents

By Bruce C. Schepens

The Balsam Meadow Hydroelectric Project is currently under construction in central California. TMCI Construction, Inc. was subcontracted to perform the shaft enlargement and lining required for the elevator, surge and power shafts. Involved in the initial work was slashing the elevator and surge shaft into a previously excavated borehole. The elevator shaft then required a reinforced concrete lining and structural steel installation. Throughout the course of construction, numerous design changes occurred, necessitating a lining in both the power and surge shafts. These changes caused TMCI to design two underground hoisting systems to install these additional linings. An analysis of the construction methods used is now given. Introduction The Balsam Meadow Project consists of an underground hydroelectric powerhouse designed to provide additional capacity and energy to the Southern California Edison system during critical peak demand periods, and has the capability for pumped storage operation. The project is located in the Sierra Nevada Mountains about 55 miles northeast of Fresno. The project will divert water presently flowing from Huntington Lake to Shaver Lake to power a single 200 megawatt turbine generator. The approach used to the shaft slashing was governed partially by the strict CAL-OSHA requirements, which became more stringent after the recent Helms' Creek accident. A scaled down sinking plant was used to minimize economic risk and to simplify the excavation and lining scheme.

Jan 1, 1987

By James M. Murphy

INTRODUCTION In the fall of 1983, the fourth new Rapid Transit System constructed in this country in the last forty years will go into revenue service. The Baltimore Metro will bring to this major Mid-Atlantic seaport the first phase of a planned intermodal transit system, serving a metropolitan area with a population in excess of four million people. Originally, the Mass Transit Administration (MTA) considered construction of a twenty-eight mile system known as Phase 1. Its two lines would run from the center of Baltimore City, one going northwest to Owings Mills and the other south to Anne Arundel County. Legislative approval was granted in April, 1976; however, funding was limited to constructing a segment fewer than eight miles in length, along the northwest corridor from Charles Center to the Baltimore City county line. This segment is known as Section A. The project is 80% federally funded and 20% state funded, with a capital cost estimate of $797,000,000 to complete. This report addresses the development and implementation of a Coordinated Insurance Program for the construction phase of Section A, and includes a description of the associated risk management process. GENERAL DESCRIPTION OF SECTION A Section A of the Baltimore Metro is composed of a rapid transit line eight miles in length which serves the northwest corridor between Charles Center in downtown Baltimore and Reisterstown Plaza at the Baltimore City county boundary. The line is completely grade separated and, once operational, will provide high speed automated rapid

Jan 1, 1983

By I. Koliabina

In this paper, the results of mathematical modeling of casing pipes decontamination from radio-active new mineral forms directly in boreholes using hydrochloric and hydro-silicic-fluoric acids are presented. Modeling for highly and low radioactive coatings on the walls of casing pipes of Anastasievka oil-and-gas deposit was performed using GEMS software, based on the method of Gibbs energy minimization. Calculations have shown that thorianite and goethite, that are present in low-active crusts, detected in casing pipes uplifted from comparatively low depths, are well dissolved in hydrochloric acid, but radiobarite is almost insoluble. For the same acid concentrations, almost all radiobarite of high-active coatings detected in pipes uplifted from considerable depth is dissolved. To evaluate the possibility of decontamination of pipes from radiobarite of low-active coatings, modeling of crust dissolution under the action of H2SiF6 has been performed. The results have shown that for acid concentrations of more than 13 % almost all Ra and Ba are dissolved while all iron and thorium remains in goethite-thorianite solid solution. For the same acid concentration, almost all radiobarite from high-active coatings is dissolved. Therefore, no reagent allows decontamination of pipes from coatings of both types. It seems that successive or simultaneous use of both reagents (HCl and H2SiF6) in certain ratio is required. To clarify this issue, further experimental and model investigations are necessary. The issue of decontamination of casing pipes from galena that is present in high-active crusts also needs to be clarified.

Jan 1, 2005

By Milton E. Wadsworth, M. Ken Han

The kinetics of leaching of galena in hydrochloric acid solutions with sulfur dioxide gas have been investigated experimentally. The leaching method is then applied to complex sulfide concentrates to evaluate its selective leaching capability and to develop a new hydrometallurgical lead extraction process based upon the method. The leaching reaction follows a linear rate with an activation energy of 61.9,KJ/mole. The rate Is of first order with respect to the product [H+] [Cl-] . Excel lent selective leaching capability f s demonstrated and an attractive hydrometallurgical process flow sheet is proposed.

Jan 1, 1989

By Bela Koman

Abstract - A shiploading terminal near Punta Arenas, the southernmost city of the world (lat. 53°-10'S, long. 70°-54' W) is described. Strong winds, choppy seas, frequent gales, rain, and snow make it difficult to load ships at an offshore berth in this area. Detailed site investigations, including a wind-recording program, supplied sufficient information for the analysis of operating conditions. The weather pattern of the entire region, including the predictability of gales, was utilized in the analysis. The results showed that a bulk loading terminal at this location is feasible, provided that the design takes into consideration the specific problems of the site. The final layout shows a terminal that can be approached from several different directions, depending on the direction of the wind. The mooring system is arranged to allow alter- native ways of attaching and casting off mooring lines and executing docking and departing maneuvers. The berth is supported on piles and contains the minimum of structures, relying on a slewing shiploader to reach the ship in any position, with only limited fore and aft shifting of the vessel for loading the extreme hatches. Results of wind recording, statistical analysis of wind and wave data, operating criteria, and the results of berth availability analysis are included in the paper.

Jan 1, 1987

By Chris J. Conway, Bruce W. Atkinson, Graeme J. Jameson

The flotation of coal in the fie and coarse particle size ranges presents particular problems. Fine or ultra-fine coal less than 100 microns presents a challenge to conventional flotation machines because the rate of capture of the coal particles can be very low, so longer residence times are needed. Also, conventional mechanical cells are not normally designed with froth properties in mind. Froth drainage may be inadequate, leading to excessive entrainment of ash. The upper limit of flotation of coal is normally put at about 500 um (30 mesh). It appears that, in mechanical cells, coarser particles tend to be torn away from bubbles in the turbulent environment created by the impeller. In this paper, results are presented from plant trials of a high-intensity flotation column of novel design, namely the Jameson cell. Extensive trials have been conducted on coal slurries with a top size of around 1 mm. Size-by size analysis shows that it is possible to achieve high yields of low ash product over the whole particle size range.

Jan 1, 1995

By Walter E. Heinrichs

This case history really started during the tail end of WWII when two Navy men, both Colorado School of Mines graduates, got together in Washington, DC, while they were assigned to the Office of Navy Petroleum Reserves doing some of the first aerial magnetometer work ever done on a practical oil exploration basis over the offshore area of the Gulf Coast. When separated from Naval Service active duty in 1946, the two men, Walter E. Heinrichs, Jr., and Robert E. Thurmond, tried, unsuccessfully, to form a commercial air magnetometer business. Later they got together again in Jerome, AZ, with Newmont Mining's early geophysical exploration endeavors from 1947 to 1949. Subsequent to the Newmont experience, they jointly proposed a specific mining geophysical exploration and development program to Herbert Hoover, Jr., then president of United Geophysical Co. of Pasadena, CA. Mr. Hoover, in consultation with his father Herbert Hoover and others of his staff at United, particularly Edwin G. Schempf, executive vice president, and Raymond A. Peterson, vice president of research, agreed to establish the proposed program under United's auspices, to be headquartered at Tucson, AZ. The primary objective would be to practically test and develop various mining geophysical methods and techniques while exploring particularly for base metals in the general area of southeast Arizona and southwest New Mexico.

Jan 1, 1991

By V. J. Kecojevic, W. A. Wilkinson

Mining companies are increasingly looking at Global Positioning System (GPS) technology coupled with 3D mine planning and visualization systems to deliver increased productivity and reduction in operating costs in drilling and blasting operations. Leveraging GPS into drill and blast operations requires that a drilling plan be developed and imported into the GPS to guide the operation to a planned and desirable outcome. State-of-the-art mine planning software systems provide the engineer with a 3D environment in which to design and visualize drill and blast plans. This paper discusses producing and exporting 3D drill and blast plans to GPS and how some coal companies are utilizing GPS and mine planning software technology in the drill and blast process.

Jan 1, 2004

By V. Kontogianni

The underground extraction of coal is associated with ground movements extending from the mining area to the ground surface, which result in bowls of ground subsidence, with amplitude exceeding the amount of several meters and occasionally with important tilt and curvature of ground surface. Such changes at both the underground environment and surface topography lead to destruction of buildings, failure of utilities and transportation networks, and occasionally formation of areas vulnerable to flooding, or even small pools. Based on geodetic surface measurements of ground elevation changes, various theories and empirical models relating surface subsidence with the geometry of underground voids formed have been proposed, and predictions of expected subsidence in the form of contours have been estimated. In this study a case study of planning of a new highway network through areas in which coal extraction was also planned is discussed. This work is partly funded by EU. The optimum solution selected was a modification of the initial highway planning, so that the road is increased in length and by-passes the richest coal-field, where maximum post-exploitation subsidence was predicted, and only crosses either minor coalfields, which are not to be exploited, or even margins of main coalfields, in which minor post-exploitation subsidence is expected.

Jan 1, 2006

By Alex Harrison, Steve Kasper

Various countries around the world have testing and manufacturing standards in place for steel cord belting. These standards are very comprehensive in what they allow the end user to specify, however, their practical significance in terms of belt life is more difficult to quantify. Such testing standards will be briefly reviewed in this paper in relation to the implication for end user expectancy. Since there is no US standard of manufacture, the end user is left with writing their own specifications. In addition, such standards do not address the effect on belt life of manufacturing faults, such as cord plane buckles, or lateral cord movement. Some new technology used to test steel cord belting will be described as an aid to both manufacturer and end user. Specific end user related issues addressed on this paper are: Tracking and belt quality Cord plane irregularities and performance Cord size and belt life Cord fatigue and testing

Jan 1, 1993

By Y. Ye, J. D. Miller

Certain bituminous coals are known to contain appreciable quantities of natural fossil or subfossil resin. Such resinous coals are found in the western US, particularly the Wasatch Plateau coalfield of UT. Some of the seams in this field contain an average of 5% resin. This fossil resin has been recovered by gravity and/or flotation processes since 1929. Resin concentrates thus produced are of low quality and are usually refined by solvent extraction. The purified resins are of commercial importance in the adhesive, coating, rubber. and ink industries, etc. An improved flotation technique has been developed which involves ozone conditioning to selectively float resin from high-volatile bituminous coal. With this flotation process, a concentrate product which contains 95%

Jan 1, 1990

By W. S. Fyfe, G. Southam, T. J. Beveridge

Sporosarcina ureae was able to grow in the presence of tip to 10-ppm L-asparagine complexed gold. However, 10 ppm Au3+ was found to be highly toxic to Sporosarcina ureae, killing 109 bacteria/mL within a few seconds. To compare the effects of these responses on gold mobility, an in vitro bacterial biofilm model was developed to examine the interaction be¬tween Sporosarcina ureae and ionic gold or L-asparagine gold complexes in gravity fed columns. The immobilization of ionic gold was between 80% and 90% over a period of one week. But, as the available cellular reactive sites became saturated, immobilization decreased to 14% within two weeks. In the L¬asparagine-gold system, gold immobilization in the cytoplasm occurred at a high rate (80% to 90%) throughout the experi¬ment, with limited toxicity towards Sporosarcina ureae. The bacterial immobilization and detoxification of L-asparagine¬complexed ionic gold was associated with a low molecular weight, i.e, <5,000 dalton (atomic mass unit), intracellular protein fraction. This peptide-complexed gold would allow for the continued biogeochemical cycling of gold under ambient (<100°C) surface or near-surface conditions.

Jan 1, 2000

By J. C. Yingling

An approximate analytic- model is developed for minerals liberation when comminution processes are applied to multi-component ores, i.e., ores that include grains of multiple mineral species. The model employs a one-dimensional representation of ore texture similar to that employed by King (1979) and Klimpel and Austin (1983). The spatial texture representation is viewed as being generated by a stationary semi-Markov process. Associated semi-regenerative processes are defined that can be used to establish, approximately, the joint distribution of particle size and composition, where composition refers to the identities and relative proportions of mineral species included within the particle. Numerical predictions made by the model are compared to size and composition distributions observed in previous experimental studies.

Jan 1, 1992

By Martin L. Smith

Mine waste characterization and risk assessment currently focesses on water quality and largely ignores boththe charteristics of the wastes themselves and how wastes interact with the environment. Characterization of the parameters that control contamination of pore waters and their migration can quantitatively assess risk and remediation strategies in terms of cost effectiveness and risk reduction. Since mine waste characteristics are spatial, geostatistical methods should be used for characterization and assessment. A number of geostatistical methods are reviewed in terms of their application to mine waste sampling, modeling and risk assessment and management.

Jan 1, 1995

By J. C. Norman

The boron review arrived too late for the June issue. The United States was the world&apos;s largest producer and consumer of boron compounds during 1993. Boron mineral concentrate and chemical production in the United States totaled an estimated 958 kt (1.05 million st), yielding 526 kt (580,000 st) of B203, according to the US Bureau of Mines. Estimated value was $322 million. This level of production was about 5% less than 1992 revised production figures. The United States continued to provide essentially all its own boron while maintaining a strong position as a source of sodium borate products and boric acid to foreign markets. Domestic employment in the mining and beneficiation of boron products in 1993 was 900 people, about the same as in 1992. That was down from 1988 levels of 1250 people. Total world production of boron in 1993 was about 2.5 Mt (2.75 million st), yielding about 1.2 Mt (1.3 million st) of B203. World production in 1993 was about equal to revised 1992 levels. Production United States In 1993, mines and processing operations in southern California were the only domestic sources of boron mineral concentrates and chemicals. Domestic producers, in order of quantity of production, were: • US Borax and Chemical Corp., which operates an open pit kernite and tincal mine at Boron, CA, producing boric acid and borax products, • North American Chemical Co., which produces boric acid and borax products as coproducts from chemical operations at Searles Lake, CA and • American Borate Co., which produced small amounts of colemanite and shipped from inventories from its operation in Death Valley, CA.

Jan 1, 1994

By Kalyan Saikia

An integrated statistical-geostatistical modelling of gold exploration data of Gurahar Pahar prospect of Mahakoshal greenstone belt in Central India has been attempted. Statistical modelling of gold accumulation and width reveal a positively skewed 2-parameter lognormal distribution fit with an estimate of mean gold as 0.84 gram/tonne. Geostatistical modelling provided a spherical semi-variogram function fit with mean kriged estimate and mean kriging variance of gold as 0.76 gram/tonne and 0.23 (gram/tonne)2 -respectively. Ore inventory and grade-tonnage relationships for a selected part provided an estimate of 3,36,000 tomes of ore with an average gold of 0.76 gram/tonne at 0.5 gram/tonne cutoff grade.

Jan 1, 2002

By Kenneth N. Han, Xinghui Meng, A. J. Monhemius, G. W. Warren, E. Peters

The leaching of gold in ammoniacal solutions containing various oxidants in an autoclave has been investigated. Also studied are thermodynamic and kinetic aspects of the ammonia leaching of gold and silver. The variables studied included stirring speed, temperature, concentration of ammonia, ammonium, and various anions. Arrhenius activation energy values were found to be between 47.1 kJ/mol and 86.2 kJ/mol depending upon the kinds of oxidants used. An electrochemical reaction controlling mechanism has been proposed for the dissolution reaction. The leaching behavior of gold and silver from various ores in ammoniacal solutions containing various oxidants has also been investigated. The samples tested included sulfidic as well as carbonaceous refractory ores. The recoveries of gold and silver from these refractory ores were better than 96% within 2-3 hours of leaching time.

Jan 1, 1993

By H. F. Haller, H. C. Pattison

The research program described in this paper is sponsored by the Advanced Research Projects Agency of the Department of Defense and monitored by the Bureau of Mines, United States Department of the Interior. PROGRAM DEVELOPMENT While Holmes & Narver is better known in other fields, the company has been active in many phases of underground excavation for over twenty years. In the 1950&apos;s, H&N participated in design and construction of nearly twenty miles of waste disposal tunnels in Southern California. As Architect-Engineer for the Atomic Energy Commission, we had design and management responsibility for many miles of tunnels and for thousands of feet of exploration and big hole drilling, from coast to coast in the States, and for gas well completions and exploration drilling for the Navy and the National Science Foundation from Pt. Barrow to Byrd Station in Antarctica. In my ten years with the company, we contributed to the development of big hole drilling techniques at a number of sites and analyzed the capability of boring machines for many of the tunnel projects. In a 1965 engineering study of a hundred miles of vehicular tunnels in rock under New York City, we investigated

Jan 1, 1997

By J. A. Procarione, M. K. McCarter, Bradley C. Paul

A numerical technique is described which can be used to model the quantity and distribution of air flow through broken rock. The method can also describe gas concentration and temperature distribution. A computer code implementing the numerical approach was developed to assist in determining the feasibility of a proposed modified in-situ leaching method for extracting copper from sulfide porphyry deposits. This mining method requires air to be forced through cells of rubblized ore. The flow serves to supply oxygen for the leaching reactions and to dissipate heat that would other-wise build due to the exothermic reactions. The method substitutes the Carman equation into the Laplace equation. The solution of the resulting non-linear formulation is done on a finite difference grid using SOR with iteration improvement of coefficients. This procedure yields the required air flow pattern and pressure drop. An equation for advection with absorption is then solved over the same grid using explicit schemes to yield oxygen concentration. Finally, a similar technique is applied to the convective heat transfer formula to yield the temperature profile. The model is potentially applicable to such mining problems as the prediction of leakage through caved ground, the prediction of methane concentration in gobbed ground, and the prediction of heat build-up in caved workings.

Jan 1, 1989

By F. G. Miller, M. Polat, S. Chander

Flotation was used to achieve improved separation of magnetite from the float and sink products obtained from heavy medium separation and to reduce the load of the medium cleaning circuit. The investigation was carried out in two successive phases. In the first phase, tests were performed on in-plant samples from the Homer City Coal Perdition plant to determine what effects variables such as medium density, particle size and magnetite source had on the efficiency of the process. In the second phase, the optimum conditions determined in the first phase were used to determine the applicability of the process to other selected coals from central Pennsylvania. It was observed that flotation was very effective in the separation of magnetite from coal. In most of the cases investigated, the magnetite recovery was approximately 99% with a magnetite grade ranging from 95 to 99%. The grade of the magnetite decreased as the ash content of the coal increased and the particle size of the magnetite decreased.

Jan 1, 1994