Search Documents

By M. E. Rossi

This paper discusses the use of Conditional Simulation (CS) models to provide mill feed grade profiles for different time periods. The conventional approach of classifying block estimates as ore or waste generally does not adequately represent dilution, lost ore and the anticipated grade control data, including variability of mill feed from the pit and possible stockpiles. The detailed simulation of grade control practices can be done, but at the Pre- or Feasibility stage of the project may be impractical, since drawing dig limits on multiple benches is tedious and time consuming. Using the Feasibility Grade Control (FGC) method as developed by the Centre for Computational Geostatistics (CCG, University of Alberta-Edmonton), the CS models can be processed quickly to establish dilution and lost ore, and predict daily or short-term feed to the mill. The simulated nodes can be aggregated into selective mining units with adequate representation of likely geometries to be recovered from the pit, to mimic anticipated selectivity. An example from a large copper deposit is shown. The study provides an estimated stream of tonnages and grades fed to the plant by mining periods of interest and based on a specific mine design and schedule. The resulting cash flows support the economic and financial analyses of the Feasibility Study; also leads to improving mine schedules; and aids in developing blending schemes if necessary. INTRODUCTION The conventional approach of separating mineralized material into ore or waste categories does not always include a realistic amount of dilution and ore loss. Also, often it does not provide a good estimate of the grade that will be fed to the mill. If the grade control estimates are unbiased, they will over the long run represent the long-term average of grades fed to the mill; but the anticipated variability of mill feed from the pit and stockpile sources may be misrepresented. Some references on traditional grade control implementations can be found in Chunnett (1982); Davis et al. (1989); Srivastava et al. (1992); and Nowak (1992). Alternative methods based on economic variables improved significantly on the purely grade-based control methods, see Douglas et al. (1994). Further developments involved the use of geostatistical conditional simulations (CS) and profit models, which in several cases have been successfully implemented (Aguilar and Rossi, 1996; Rossi, 1997; Deutsch et al., 2000; Norrena and Deutsch, 2002; Neufeld, 2005; Jewbali and Dimitrakopoulos, 2009). But they can be impractical, mostly due to the lack of understanding of the methodology involved; even if semi-automatic dig limit drawing is implemented, there is always a need for is tedious and time consuming checking and corrections, even if using a single profit model derived from the simulated grades.

Jan 1, 2019

By Yingbao Yang, Jinyue Liu, Yonggang Wei, Bo Li

Due to the depletion of copper ore with high-grade and low impurity contents, the raw materials for copper smelting exhibit low copper contents and high impurities. High-impurity elements lead to the poor performance of the final copper product; thus, the removal of impurity elements during the oxygen-enriched copper smelting process is crucial. In this study, based on the production of high-grade matte, the occurrence states of impurity elements (such as As, Pb, and Zn) are analyzed in the input and output materials of the oxygen-enriched smelting process, and the phase transformation mechanisms of impurity elements are revealed during the oxygen-enriched smelting process. The effects of temperature, Fe/SiO2 ratio and oxygen concentration on the distribution behaviors of impurity elements in dust, slag and matte and the removal rates of impurity elements in matte are clarified. The results show that the impurity elements mainly exist as As4, As4S4, As2O3, Pb, PbS, PbO, Zn and ZnS in dust, as FeAsO4, As2O3, FeAsS, PbSiO3, Zn2SiO4 and ZnFe2O4 in slag, and as As, FeAsS, PbS, PbO and ZnS in matte. High smelting temperature, low Fe/SiO2 ratio and low oxygen concentration are beneficial for improving the matte grade and the removal rates of impurity elements Pb and Zn in matte. Low smelting temperature, low Fe/SiO2 ratio and high oxygen concentration are beneficial for removing impurity element As in matte.

Aug 8, 2023

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is the most popular and practiced mining method in underground hard rock mines. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason is the unavailability of free faces as compared to opencast bench blasting. The geological and geotechnical parameters change gradually even within the stope itself. So, the blast design parameters should be planned according to the scenario of the upcoming ring. The blast design parameters like burden, toe spacing, inclination of blastholes, diameter of blastholes, charge density of explosive, etc., play an immense role in the rock damage. For the proper breakage of rock, the movement of burden is the prime objective. To study this, an explicit dynamic based modeler of M/s Ansys was used. The burden values were varied from 20 to 65 times of blasthole diameter to assess the optimum burden value during the study. The models were simulated for the rock having uniaxial compressive strength as 35 MPa and 102 mm blasthole diameter. Three holes were simulated having depth around 14–14.5 m. Different blast design parameters and respective blast-induced ground vibration have also been measured at the experimental site. The core samples of the rock present at the experimental site have been used for the evaluation of geotechnical parameters. These geotechnical parameters were used in the simulation models. The volume of rock excavated along the free face has been calculated in each model by varying the burden. It has been found that the burden value can varies from 35 to 40 times blasthole diameter (3.6–4.1 m) to achieve a greater volume of rock along the free face for 102 mm blasthole diameter and rock of 35 MPa uniaxial compressive strength.

Dec 22, 2023

By E. Allen Wendt

It is both a great pleasure and something of a challenge for me to have this opportunity to address a gathering encompassing such a wealth of expertise in the minerals field, It is particularly challenging because I have been asked to turn your attention from the relatively glamorous subjects of gold and money to the more mundane questions of our International commodity policy and the place of buffer stocks in that policy. However, these questions may be of more immediate importance for our economic interests at home and Abroad. I can testify that the problems affecting international commodity markets and the possibility of international action To resolve those problems are matters of real concern to Washington as well as to your industries,

Jan 1, 1978

By Madan M. Singh

A new mining project can raise questions about what effect it will have on the community after it closes. Historically, little was done by communities to plan for and accommodate the changes in the economic infrastructure when a mine project is finished either after the ore runs out or if market conditions deteriorate and make it unprofitable. Projects that were underfunded were generally unable to withstand periodic market downturns. However, data in a recent study conducted by the Seidman Research Institute leads to the conclusion that, even when a mining project is terminated, there can be (and, in the specific case studied, is) a residual beneficial economic effect in the community, which lasts for a long period of time.

Jan 1, 2010

By Kenneth E. Merklin

The heavy media process is now being used extensively throughout the world for the gravity concentration of a great number of different minerals. The process is a commercial adaptation of the heavy liquid procedure which has been used in laboratories for many years to separate mineral of different specific gravities. In the heavy media process, a suspension of finely divided particles in water is used to increase the apparent specific weight of the fluid to the desired separating point. The original heavy media process used sand, galena, pyrite and occasionally other materials as the solid constituent of the separating suspensions. As the process developed, the need for a more universal media meeting the following requirements was recognized: 1. High specific gravity. 2. Resistance to abrasion. 3. Resistance to corrosion, 4. Readily reduced to a suitable size consist for suspension in water. 5. Available in quantity at economical price levels. 6. Easy to recover by a simple method.

Jan 1, 1958

By A. Simon, J. Weyer, J. Brune, V. Zhiteneva

"Reiche Zeche is a lead-zinc-silver deposit in Freiberg, Germany, that was mined for over 800 years. Since 1969, Reiche Zeche has been a teaching and research mine with numerous adits for dewatering large amounts of inflowing water. Infrequent metal water quality monitoring in the 1980-1990s and flooding of the mine in 2002 led to a lack of relevant data. New measurements were taken at different level adits and ore veins for comparison to historical values, revealing pH levels as low as 1.95, conductivity as high as 22000 µS/cm, and an overall trend towards less acidic waters. INTRODUCTION Reiche Zeche is part of the Himmelfahrt Fundgrube, a former iron ore mine in Freiberg, Germany, in the Erzgebirge mining region of Saxony. The polymetallic sulfide ore found in Freiberg was mined from 1168 to 1969, and though it is no longer producing ore, Reiche Zeche remains as a teaching and research mine for the Technische Universität Bergakademie Freiberg. The most important ore minerals mined were sphalerite, galena, pyrite, chalcopyrite, and silver, and important gangue minerals include calcite, fluorite, barite, siderite, and quartz (Zänker et al 2002). Over one thousand ore loads were mined from this region during operation, which was ceased in 1969 after the lower part of the 700 meter depth was flooded, leaving only the top 200 meters under the surface open for research and teaching. Mined materials from this region can be separated into high grade ore and waste rock. High grade ore, composed of pyrite, sphalerite, galena, chalcopyrite, and arsenopyrite, was brought to surface for smelting during mine operation, and spaces were backfilled with waste rock, which is the primary site of sulfide oxidation and acid mine drainage (Haubrich and Tichomirowa 2002). The waste rock includes remnants of ore from ore loss, veins which were too small to mine, or ore minerals within host rock. Waste rock is primarily composed of biotite gneiss, with sulfides including jarosite, gypsum, minor anglesite, scorodite, and sulfur (Haubrich and Tichomirowa 2002). When weathered, the gneiss forms clay minerals such as illite and kaolinite (Haubrich and Tichomirowa 2002)."

Jan 1, 2016

By P. L. Yorio, D. R. Willmer

"The current paper presents the results of a study designed to explore the types of practices that are fundamentally important to developing and maintaining comprehensive risk-based health and safety management systems (HSMS) in mining organizations. Eighteen practicing health and safety (H&S) executives, managers, and professionals from a variety of mining commodities were asked to assess the fundamental importance of 20 distinct elements and 133 different practices assembled from a review of several HSMS consensus standards. The research approach assumes that developing and maintaining a robust HSMS requires unwavering attention to activities designed to either: 1) directly contribute to a risk management system’s plan-do-check-act cycle; or 2) build an organization’s internal infrastructure without which the cycle cannot be sustained. The results of this study suggest that the following areas require consistent focus and attention: Leadership Development; Accountability; Knowledge, Skills, and Abilities Development; System Coordination; Culture Enhancement; Behavior Optimization; and Risk Management Studies. Each element and its corresponding top-ranked and top-rated practices are discussed.INTRODUCTION Since the time of the Industrial Revolution, occupational health and safety (H&S) management has been a topic of practitioner thought and academic inquiry (1). In the U.S., decades of regulation and research have resulted in a surplus of prescriptive information (techniques, tools, approaches, standards, programs, practices, policies, etc.). With an abundance of such information, a simple H&S solution to address a problem in the U.S. mining industry may seem straightforward. Counter to this assertion, however, some evidence suggests that the abundance of information may create complexity and cause confusion in the minds of organizational leaders and H&S managers, ultimately discouraging the voluntary pursuit of a sound approach (2). In line with this perspective, in 2006 the U.S. National Mining Association (NMA) formed an independent commission to examine H&S management issues within the mining industry. The findings of the commission called for the mining industry to adopt a risk-based management paradigm. In the presentation of its findings, the commission stated that “…every mine should employ a sound risk-analysis process, should conduct a risk analysis, and should develop a management plan to address significant hazards identified by the analysis” (3). Grounded in the well-known plan-do-check-act cycle, the recommended risk management system allows for mines to ground strategic management choices in their mine-specific hazards and risk profiles"

Jan 1, 2015

By E. A. Metz

Work related pulmonary diseases are in the top TEN causes of occupational disability and death in the United States. Likewise, it also ranks high inmost of the other industrial countries. It is difficult to know the true occurrence of occupational lung disease because of poor documentation. This is especially true when one examines workers’ compensation claims. Most frequently, silica and asbestos are paramount in our discussion of work related pulmonary disease. Little consideration is given to other “dust-related” diseases, irritant reactions, reactive airway responses, and hypersensitivity reactions. The major classification of occupational lung diseases will be discussed. This includes both acute and chronic disease that arises in the work place, especially, the mining industry. It’s more important to make an accurate evaluation and diagnosis for the prevention of disease among other workers.

Jan 1, 2000

By M. A. Reyes, J. Bickson, J. R. Srednicki

Federal laws mandate the presence of refuge alternatives (RAs) in underground coal mines and provide guidelines for harmful gas removal. After an explosion, harmful gases can follow survivors into an RA and can reach a deadly concentration. Investigators from the National Institute for Occupational Safety and Health (NIOSH) tested 12 ventilation system configurations (VSCs) to purge sulfur hexafluoride (SF6) tracer gas from a built-in-place (BIP) RA in the Experimental Mine in Bruceton, PA. Using a borehole air supply, tests were conducted with airflows of 750 and 1,000 standard cubic feet per minute (SCFM). Excluding a VSC where the air inlet was 1.98 m (78 in) from the air outlet, the results show that the time to purge the SF6 concentration from 1,000 parts per million (ppm) to 25 ppm ranged from 26 to 29 minutes for an airflow of 750 SCFM and ranged from 18 to 23 minutes for an airflow 1,000 SCFM. Mines can use this information to reduce purge time in case of a mine disaster and determine which VSC to avoid. INTRODUCTION After a fire or an explosion in an underground mine, the concentration of carbon monoxide can reach a fatal level. In a mine disaster, the main goal is to escape. However, if miners cannot escape, they have to migrate to a location to find refuge and, if possible, communication, and a borehole source for a fresh air supply. To ensure survival of the miners, Federal laws mandate the presence of a refuge alternative (RA) within 304.5 m (1,000 ft) of the nearest mining face. In addition, Code of Federal Regulations Title 30 CFR Section 7 sets the guidelines for personnel tracking, RAs, and the removal of noxious gases in underground coal mines (Mineral Resources, 30 CFR, 2014). Federal regulations define an RA as a protected, secure space with an isolated atmosphere and integrated components (Mineral Resources, 30 CFR, 2014). There are three types of RAs: portable metal RAs, portable tent-type RAs, and built-in-place (BIP) RAs. A BIP RA is constructed using masonry or other stoppings to create an isolated space in a mined-out area. Blast doors are installed in one or both of the stoppings for the miners to enter the RA. Furthermore, RAs must provide the following components: breathable air, food, water, air monitoring, and harmful gas removal. Federal regulations have emphasized the mandate for breathable air and harmful gas removal in the following words: “Purging or other effective procedures shall be provided for the airlock to dilute the carbon monoxide concentration to 25 ppm” (Mineral Resources, 30 CFR, 2014). The purpose of the mine ventilation system is to provide a sufficient quantity of air to the underground mine workings, to dilute methane and other contaminants, to maintain a suitable working environment, and to prevent accidents from happening (Cheng and Wei, 2014). In addition, the organic nature of coal amplifies risks from poisonous gases, explosions, and fires (Engström et al., 2018). If an underground coal mine ventilation system fails after an explosion, the concentration of toxic gases, most notably carbon monoxide, will increase. Carbon monoxide is dangerous because it creates tissue hypoxia by binding to hemoglobin (Özmen and Aksoy, 2015).

Jan 1, 2019

By D. Nutakor

This paper presents the results of a study conducted on a slope failure that occurred in the Q7 mining cut at Rio Tinto's Bingham Canyon Mine. The slope failure occurred in a weak rock mass with an estimated rock mass rating of 25%. The failure mechanism was of the circular type, involving ten 15-m (50-ft) benches and covered a total width of 152 m (500 ft). The analysis used Adam Technology's photogrammetric method with a two-dimensional rock fall simulation program (RocFall software) to design a 3-m- (1 0-ft-) high berm located 7 m (24 ft) from the toe of the failed mass. Back and predictive analyses were performed on a cross-section through the slide using Slope/W software, resulting in flattening the interramp angle (IRA) from 44° to 38°. This design modification produced a factor of safety (FOS) of 1.14. Sensitivity analysis involving FOS vs. pore water pressure showed that FOS is sensitive to water saturation. A dewatering system using a series of horizontal holes drilled below the slide and dewatering holes drilled from a drainage gallery has since been established to improve the stability of the slope. Throughout the one-year period since this investigation, no significant slope movement has been detected by the slope stability radar, and mining is in progress below the failure.

Jan 1, 2012

By Hans Ehdwall

INTRODUCTION Investigations of radon and radon daughter concentrations in Swedish [non-uranium] mines started in the late 1960's. The first screening measurements showed that the average annual exposure to radon and radon daughter products was 4.7 WLM. The main reason for high radon and radon daughter concentrations was inefficient ventilation and radonrich water entering the mine. In the radon regulations worked out later it was stated that no miner should be exposed to more than 60 000 pCi h/1 equilibrium equivalent concentration of radon annual exposure, corresponding to 3.6 WLM. Now, 1981 the situation has changed considerably. From the average annual exposure of 4.7 WLM in 1970 it is now only 0.7 WLM. Sweden has up to now had only one [uranium] mine and the work there has only been investigative. However, there are plans for a commercial uranium mine in another part of Sweden. The radon problems in these mines are widely different depending on the mineralogy. NON-URANIUM MINES The radiation problems in Swedish mines were not recognised until the late 60's. The first radon and radon daughter measurements were made in some sulphide ore mines in 1967 (1). The radon and radon daughter concentrations were surprisingly high for non-uranium mines. In order to have a complete picture of the radon situation in Swedish mines the National Institute of Radiation Protection (NIRP) decided to make measurements in all, at that time about 60 mines (2). To get results as fast as possible measurements on radon gas seemed most appropriate to start with. Sampling was made by mailing a number of evacuated 4.8 litre conventional propane containers from NIRP to each mine. The containers were then opened at the place of interest. After sampling the containers were sealed and then mailed back to the institute for measurement. The measurements were made in ionization chambers. This method only gave the radon concentration and the radon daughter concentration was estimated by multiplying the radon concentration by an assumed equilibrium factor. The equilibrium factor is defined as the ratio of the total potential alpha energy for the given daughter concentration to the total potential alpha energy of the daughters if they are in equilibrium with the given radon concentration. The results of this first preliminary survey indicated that a great many of the Swedish miners probably had an annual radon daughter exposure of more than 3.6 WLM. As the radiation exposure in non-uranium mines was not regulated in either the Swedish Radiation Protection Act or the Swedish Labour Protection Act work was started on special radon regulations. A lung cancer mortality study was also started. To check the results of the first survey and to get experience and knowledge of radon problems in mines, it was decided that personnel from the NIRP should visit each mine for a detailed investigation of radon and radon daughter concentrations starting with the ones with the highest radon concentrations. The main reasons for these so-called "basic measurements" were: 1. To estimate the doses received by Swedish miners 2. To find the sources of the high radon and radon daughter concentrations 3. To find appropriate counter-measures 4. To determine the most typical equilibrium factor for each mine. Unlike most uranium mines the reason for high radon concentrations in non-uranium mines is seldom the occurrence of highly radioactive minerals. The main sources were found to be waste-rock and radon-rich water. In order to filter and warm up the inlet air, especially in winter time, it was very common at that time to suck the air through broken wasterock. By doing so the air was contaminated with radon from the waste-rock and radon-rich water in it. It is noteworthy that the radium and uranium concentration in the waste-rock is relatively low. The uranium concentration is only of the order of 15 - 20 ppm. The action to prevent this contamination of the inlet air was to change the direction of the ventilation and in the case of radon-rich water entering the mine the action was to prevent the air coming into contact with the water. The first calculation of the radon daughter exposure of Swedish miners was based on radon gas measurements. The radon daughter concentration was estimated by using an assumed equilibrium factor of 0.5. Later when the mines were visited by institute staff it was possible to compare the assumed equilibrium factor with the measured ones. It was found that the factor varied from 0.15 at the air inlet to 1.0 at the air outlet and the average equilibrium factor on workplaces for almost all mines was between 0.4 and 0.6. The result of the exposure calculation in 1970 showed that more than 40 % of the miners had an annual radon daughter exposure of more than 3.6 WLM. The overall average was 4.7 WLM and the maximum annual expo-

Jan 1, 1981

By Sotiris N. Kamenopoulos, Zach Agioutantis

Rare earth elements (REEs) are considered critical minerals for industrial and defense sectors. REEs are not as rare as the word “rare” portrays; yet, the exploitable and/or profitable deposits of REEs may be found only in certain geographical areas. The political and social conditions characterizing these areas may not always be in favor of mining operations. These conditions are imposing the need for extra consideration on the geopolitical constraints prior to any decision-making and before any mining project begins. This study assesses the risk related to mining projects for areas that feature REE deposits based on a geopolitical viewpoint. Probable ranking differences between the current assessment and a 2015 assessment are discussed. The comparative indicators used and the appraisal procedure applied in this comparison are based on a number of different geopolitical indicators. Several ranking changes occurred between 2015 and 2019.

By Paul Soros

The rationale for innovations in two directions is identified: raising capital and annual throughput, in order to avoid the cost of constructing and operating an additional system and to reduce the capital cost of pits and tunnels, applicable to installations of any capacity. Cast histories cover railroad unloading of bottom dump cars, rotary dumping of random cars, with and without indexer, and unit trains as well as truck unloading of multiple grades of coal.

Jan 1, 1985

By Judson G. Brown

In the May, 1969 issue of Mining Engineering the Editorial Director, John V. Beall, described the Japanese Onahama Copper Smelter and Refinery as follows: "On the shore of the Pacific, 120 miles north of Tokyo, is the world's most modern copper smelter and refinery.? One of the improvements that has been made at the Onahama Refinery is the quality of the electrolyte in the copper refinery electrolytic cells. This has been accomplished by reducing the concentration of slimes in the cells between the electrodes. In a December 19, 1966 review in Chemical Engineering magazine reference was made to some tests in Sweden as follows: ?However, at 1,000 amps/sq.M., satisfactory cathodes could be prepared, provided electrolyte flow past the anode and cathode was at least 3 to 4 meters per minute, and the slime content was not allowed to exceed 20 to 30 mg. per liter. By dropping the current to 500 amps with the same electrolyte velocity, the slime content could grow to 50 mg. per liter (50 ppm) without causing occlusion at the cathode." From this data it appears that the production capacity of copper refining electrolytic cells can be significantly increased. In order to do this the concentration of suspended contaminating slimes in the electrolyte solution is reduced by filtration. The electrolyte in-between the active electrodes must be purged with higher velocities to maintain a high concentration of the desirable copper ion in the liquid film adjacent to the cathode and the sulfate ion in the liquid film at the anode. This higher velocity also carries away from the cathode the undesirable impurities released from the anode as they are released into the electrolyte as filterable solids.

Jan 1, 1970

Newmont Mining Corp. has been producing gold from the Carlin Trend for more than 45 years. Naturally, the focus, scale and complexity of the operations have changed considerably during this time. Newmont discovered and developed the Carlin Main orebody that is located about 32 km (20 miles) north of Carlin, NV. The property was developed as a one-mine, one-gold mill treatment plant operation, which produced about 6.2 t/a (200,000 oz/year) of doré gold bars. The initial mine, mill and gold refining facilities were relatively small in comparison to today?s standards. The milling circuit used the Merrill-Crowe zinc precipitation process to recover dissolved gold and prepare a concentrated precious metal ?precipitate? to be melted into a doré bar for sale.

Jan 1, 2012

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By Casters B. Foster

The U.S. Department of Energy has undertaken, in a cost sharing partnership with industry and utilities, an extensive coal-oil mixture (COM) combustion program in a number of promising applications. One of these is the injection of COM through tuyeres into a blast furnace in lieu of oil. From work done previously, it has been established that COM can be burned in existing oil, fired facilities. The issues being addressed by the current DOE program are: 1) determination of best available technology to achieve environmentally acceptable operation, and 2) determination of applications for which COM can be utilized economically.

Jan 1, 1978

By J. Fuchs

This paper describes the mechanized narrow vein cut-and-fill approach used for the Deep Copper orebody at Falconbridge Limited's Strathcona Mine. Strategies for achieving high productivity while maintaining ground stability at depth and controlling dilution are discussed, including the use of mini-electrohydraulic drilling equipment, containerized truck haulage, consolidated rockfill placement techniques, and a miners' incentive system.

Jan 1, 1992

Powder River Basin (PRB) mines were originally built to serve power plants designed specifically for their coal. Sulfur was the major concern, with BTU and sodium limiting the market for some. The Clean Air Act has extended the PRB market into plants converting from other coals. These new customers are more sensitive to constituents affecting boiler and precipitator performance. At the same time, the prospect of deregulation is forcing power companies to control cost more stringently than ever. Jacobs Ranch Mine has responded to the changing marketplace with an expanded coal quality and customer service program.

Jan 1, 1998