Search Documents

By Thomas F. Martin, Daniel J. Sieve

In April 1988, the joint venture of Morrison-Knudsen and Paschen Contractors (M-K/P) was the successful low bidder for the Metropolitan Water Reclamation District of Greater Chicago's (MWRD) Contract Number 73-164-2H. This project is yet another in the MWRD Tunnel and Reservoir Plan (TARP) devised to control and treat overflows from combined sanitary and stormwater flows. M-K/P's project, located along the Des Plaines River, consists of 21,569' of tunnel mined to a 35' diameter and two tunnels totaling 14,529' mined to a 12' diameter. All three tunnels will have 12" thick reinforced concrete lining. The path for combined sewer/storm waters to reach the tunnels begins at a connection structure, continues through an approach sewer, a sluice gate structure and down a vertical shaft which is topped by a backflow structure. The purpose of the backflow structure is to prevent water surging to the surface as the system fills rapidly. Backflow preventors represent a change in design after problems developed on earlier constructed portions of the T.A.R.P.. On this project, 14 drop shafts channel flows to the tunnel system. In addition to the drop shafts, contract specifications require an emergency or escape shaft be located not more than 4000 feet from the tunnel headings. Due to long reaches without drop shafts, four access shafts had to be constructed. Thus, the total shafts constructed under this contract will be eighteen plus one 30' finished diameter construction shaft located within Miller's Meadows. Figure 1 shows the overall Des Plaines River System and the M-K/P contract connection to previous and future MWRD projects.

Jan 1, 1991

By Betty L. Gibbs

Before the first shovelful of dirt is removed from a developing mining property, a wide range of data must be collected, organized and analyzed. Among the key steps in this process are: • Visualization of the deposit from drill hole data and geologic interpretation, using all available information, including surface geology, geochemistry and geophysics. • Drawing of vertical and horizontal sections. • Construction of a 3D solid model of the deposit. • Contouring of deposit outlines and geological structure until the model represents best estimate of reality. • Estimation of grade and quality distribution. • Calculation of reserves. • Examination of possible mining methods. • Determination of economic feasibility. Many techniques are available to aid in this process of mine project feasibility analysis, from quick pencil calculations to sophisticated computer methods. However, time races faster in the complex modem business world than it did 50 years ago. Tried and true pencil methods take too much time. Opportunity may pass a mine developer by while a property is still in the first stages of analysis. In the days of hand techniques, initial analysis of the economic feasibility of a mining project usually stopped with reserve calculations and broad mine planning. Further planning was not done or was done only for the short term. Manual techniques require too much time and manpower to evaluate a longterm mining program. Mining-industry recognition of computer utility has increased. Most companies now use computers in technical applications and could not conceive of working without them. Building initial computer models of a deposit may take nearly as long as hand techniques. But the payback comes when changes are needed and a variety of mine plans are quickly tested.

Jan 1, 1990

By F. W. Brackebusch

Paste backfill is a pumpable, flowable, non-Newtonian fluid consisting generally of mine tailings and cement. Paste is prepared from dilute slurries of tailings. This is done by dewatering the slurries with conventional thickening or filtering. Backfill with a paste consistency is prepared by mixing dewatered tailings with cement and water to obtain the desired consistency of medium slump concrete. The paste is pumped with concrete pumps over relatively long (1 km or 0.6 mile) horizontal distances. More commonly, though, it flows by gravity down a mine shaft and then horizontally to the void being filled. Alternatively, cement can be added near the end of the pipeline. A certain proportion of fine particles <20 µm (<625 mesh) must be present in pastes but particles of aggregate can be added without significantly affecting the flow characteristics. Detailed testwork is necessary to design a system to prepare and place paste backfill. Testwork must determine dewatering characteristics, strength of mixes and friction in pipelines. Plants must be well engineered and controlled with PLCs because high quality control is necessary to prevent plugged pipelines and excessive pressures. Relatively small amounts of cement (3% to 5%) produce stiff backfill material 1.5 to 3.5 MPa (217 to 507 psi). The advantages of paste backfill in a mining operation include reduced mine dewatering, labor and materials savings, reduced tailings impoundment requirements, good support properties and reduced spills underground. In certain cases where more than 30% of the weight of the ore is sold as a product, the entire tailings stream can be placed underground. Paste technology can he used for surface or underground placement of tailings.

Jan 1, 1995

By E. B. Kroeger, Y. P. Chugh

The goal of this project is to develop, demonstrate, and document the beneficial use applications of a ponded F-fly ash as a road subbase material for the 2.1-mile Meredosia Industry Access Truck Route in Meredosia, Illinois. Approximately 60,000 to 70,000 cubic yards of ponded fly ash are proposed for use on this project without negative environmental impacts to surface water or groundwater. The County Highway Truck Route will consist of a 24-foot wide road built on a 0 to 7-foot thick compacted F-fly ash subbase. Laboratory testing indicates this fly ash will serve adequately as a road subbase, conforming to IDOT standard specifications. The economic considerations of using the Meredosia F-fly ash will also be developed so that a detailed cost-benefit analysis can be prepared for this project and for future projects. This project represents a two-year cooperative development and demonstration effort among the Office of Coal Development and Marketing (OCDM) of the Illinois Department of Commerce and Community Affairs (IDCCA), Southern Illinois University (SIU), Morgan County Highway Department (MCHD), Illinois Department of Transportation (IDOT), AmerenCIPS, and the Morgan County Regional Planning Commission. It is anticipated that monitoring activities will continue for a period of three (3) years after the completion of this project. The MCHD and IDOT will oversee all construction activities and long-term performance evaluation studies. Successful demonstration of large-volume beneficial use applications of F-fly ash at this site will significantly reduce management costs for power plants burning Illinois Coal. Furthermore, it will encourage similar utilization strategies at other sites in the State of Illinois.

Jan 1, 2002

By J. Allen Hennessy

INTRODUCTION The increasing price of gold and silver over the past 10 years has caused increasing activity in the exploration, evaluation and development of precious metals projects. Many of these deposits are relatively low grade and short lived which makes them economically sensitive to the major project variables such as metal price, capital cost, operating cost and of course, tonnage and grade. These deposits often have a high variability (a coefficient of variation -- o/u -- of 2 to 5) and an intermixing of ore and waste, making ac- curate ore reserve estimation difficult, especially when using traditional estimation techniques. Often, the estimation errors are not the 10-20% that we see in base metal deposits, but the errors in grade and tonnage can be as high as 50%, which can obviously have a very substantial impact on project Recent developments in geostatistics when coupled with a sound geologic under- standing of the deposit can significantly improve reserve estimates of these variable precious metals deposits. Examples will be given of actual deposits where the traditional estimates were significantly different from the mining reality. An attempt will be made to explain the applicable geostatistical tools with a minimum of geostatistical jargon and without complicated formulas. The key to improving the reserve estimates is a clear understanding of the deposit geology and especially the structural controls, the use of local estimation techniques that recognize the intermixing of ore and waste and the effect of selective mining on recoverable reserves, and the use of a global reserve estimation technique to check the results of local estimation. Geologic Controls The vast majority of gold and silver deposits being mined or developed in the western United States would be classified as epithermal deposits. These are formed by hydrothermal fluids (hot water) flowing upward through the rocks and depositing the precious metals as the fluids cool or reach areas of lower pressure or favorable chemical sites. These environments are similar to present day hot springs-type environments with some deposits being clearly associated with surface hot springs such as the Homestake McLaughlin deposit in northern California. These hydrothermal deposits can occur in sedimentary rocks resulting in deposits such as those of the Carlin district or the Jerritt Canyon deposit or the hydrothermal systems can occur in volcanic rocks forming deposits such as Round Mountain, Manhattan or Paradise Peak. The mechanisms of formation were similar in either case with the solution flow controlled by geologic structure and precious metals deposited when the conditions of temperataure, pressure and chemical environment were favorable. The gold and silver hearing solutions travel through permeable faults and fracture systems depositing the metals along these channels. The grades are often highest in the central parts of these conduits (veins) with lower grades in the surrounding rocks. An understanding of the nature, distribution and orientation of these plumbing systems is important to a realistic reserve estimate. The point to be emphasized here is that, good, sound geology in the form of geologic mapping, logging of rotary chip samples and a few carefully logged core holes can signifi- cantly improve an ore reserve estimate.

Jan 1, 1987

By David R. Reid, Lawrence W. Talbot

INTRODUCTION In the mining industry, timing in land acquisitions can be of the essence. In order to secure promising lands, deals are often negoti- ated quickly and evidenced by letters of intent containing what the parties feel are the essential terms of the deal. In some cases, a company is willing to acquire land only if it can lock up a number of promising properties, and so a "non-binding" letter of intent is used to formalize the essential terms, while leaving the company without legal liability. Later, the letters of intent will be sent to a lawyer to prepare a formal acquisition agreement. Many times, how- ever, especially in a land acquisition rush, another company will attempt to better the deal prior to the execution of that formal agreement, and the first company will be forced to rely on the initial letter of intent, only to find out to its chagrin that it has no deal In other cases, the company holding the desired property is another mining company, and the negotiation of an option or joint venture is the only way the first company can acquire an interest in the desired land. In order to make its offer more attractive, it may have to reveal confidential or proprietary information about the property or the surrounding lands. Here, too, letters of intent are often used to formalize the essential points of the agreement. Once again, however, prior to the execution of a formal joint venture agreement, the transaction may collapse and the letter of intent prove to be only that. In this paper, the authors examine the dangers associated with the use of letters of intent and the specific provisions courts look for to find a binding contract, and consider how to increase the

Jan 1, 1988

By J. W. Leonard, D. A. Newman

Discussion by N. Standish and P.N. Standish Leonard and Newman (1989) describe concepts and plans of their forthcoming project designed to increase the bulk density of broken coal at various stages of its production and handling. This is an excellent idea and something that will certainly be useful to the coal mining industry worldwide. The authors seek to achieve bulk density increase by "reducing oreliminating, through chemical additives and engineering design, particle voidage and enhance particle consolidation trickling between the point of breakage (at the face) and loading (in the shuttle car) to increase coal bulk density and productivity." In the paper, they present some supporting results of bulk density versus moisture, with or without oil addition, from the steel industry research. Unfortunately, the paper contains many misconceptions and half-truths that detract from an otherwise excellent objective of the project of increasing bulk density by reducing particle voidage-"the bottom line evaluator." Correct. Theory Definitions Coal bulk density is the ratio of the mass of a collection of discrete particles to the volume that it occupies (ASA, 1980). There can be no possible argument about this definition. Mass and volume are readily measured both in laboratory and large scale installations. So, to obtain the bulk density, one simply divides the measured mass by the measured volume. It is here that we come unstuck as everybody who has ever had to reconcile book values with the measured stock tonnages knows. Where does the problem originate? Almost invariably in a too casual a reading of the above definition and the words "a collection of discrete particles." The word collection means "a number of objects collected or gathered together, viewed as a whole" (The Oxford English Dictionary, 1989). If one knows the bulk density of a pile of coal viewed as a whole,

Jan 1, 1991

Last year in the US alone, about 425 Mt (468 million st) of minerals and coal were beneficiated by froth flotation. This number indicates that from 1983 there was a 10% increase in tonnage of min¬erals and coal beneficiated by the indus¬try. A significant improvement was seen in the tonnage processed by the nonferrous minerals and coal industries. BP Minerals America installed 85 m; (3000 cu ft) flotation cells at the Bing¬ham Canyon mine and concentrator. The new flotation circuit has fewer than 100 cells compared to 2000 flotation cells used in the old plant (Mining Engi¬neering, November 1988). Column flotation use on a commer¬cial scale continues to expand as seen from the interest expressed at the Col¬umn Flotation Symposium (Column Flotation &apos;88). The Magma Copper Co., San Manuel Division replaced all con¬ventional cells with 1.8 x 12 m (6 x 40 ft) column flotation cells for copper con¬centrate cleaning. Also, 1220 mm and 760 mm-diam (48 in. and 30 in.-diam) column cells are operating at the plant in the molybdenum circuit. A commercial Diester Flotaire col¬umn cell for fine coal recovery was installed at the United Coal Wellmore No. 20 plant. The 36.8 m3 (1300 cu ft) cell recovers 13.6 to 18 t/h (15 to 20 stph) of -590 gm (-28 mesh) coal. A similar unit has been installed at Tanoma Mining Co. in Pennsylvania. Various modifications of the column cells are being designed around the world. Jameson (Mining and Metal¬lurgy, 1988) described a new concept whereby the feed and air stream mixture is discharged into a cylindrical column of about 1.2 m (4 ft) height. Recovery and grade of nonferrous minerals have been reported to be better than that in a four-stage conventional flotation clean¬ing circuit. Flotation reagents American Cyanamid and Dow Chemical continued development of a new generation of sulfide collectors. A general feeling is development of new sulfide collectors has not kept up with flotation technology. Additionally, joint efforts between industry and chemical suppliers will likely be necessary to realize the economic benefits of the new technologies, since new chemistries respond differently compared to the conventional collectors. Flocculant development in recent years has been evolutionary rather than revolutionary. Rothenborg reported on development of a new flocculant family (a hydroxymated polyacrylamide desig¬nated S-6703) that has shown consider¬able promise in red mud clarification. Plant testing showed that this new floc¬culant could replace starch and poly¬acrylate and provide significantly higher overflow clarity. Barol Kami (Siirak) and Cleveland¬Cliffs (Hancock) reported development of an amphoteric apatite collector (ATRAC 873) that was used in Tilden&apos;s silica flotation process to increase apatite rejection. The collector was engineered for the particular flotation conditions in the complex Tilden process. Significant plant testing with ATRAC 873 showed that this reagent gave significantly in¬creased apatite rejection without any effect on silica flotation effectiveness or selectivity. Electrostatic separation Electrostatic separation is now em¬ployed in the precious metals mining industry to recover gold and silver grills from crushed slag. The installation at Paradise Peak has prompted other op¬erators to consider this application. In another development, attractive potentials for treating very fine minerals (-45 µm or -325 mesh) are being devel¬oped by Advanced Energy Dynamics and by the Department of Energy. Demonstration tests using triboelectric charging/electrostatic separation have been successful on a variety of minerals as well as coal. Magnetic separation Developments in magnetic separa¬tion have transpired on a production scale. Superconducting, high gradient magnetic separation has gained accep¬tance with the successful startup of a second unit treating kaolin at J.M. Huber Corp. This liquid-helium-cooled mag¬net generates 2.0 tesla in a 3-m-diam (120-in.-diam) bore with no power con¬sumption. Wet, high-intensity magnetic separation has been applied to sulfide mineral separations both domestically and abroad. These continuous type of separators are effective in removing residual chalcopyrite and sphalerite from other base metal sulfide concentrates. Separators using high energy rare earth permanent magnets are continu¬ally increasing. Now offered as both drum and roll type, these units are be¬coming a staple in the processing of industrial minerals. Tests using rare earth magnets strategically placed on a spiral concentrator have demonstrated the enhanced recovery of heavy miner¬als such as ilmenite. Classification Although no major technology break¬throughs in classification appear immi¬nent, there is an increasing need for more efficient and cost-effective meth¬ods to make size separations. It is be¬coming more apparent that mineral concentration methods will be more common at very fine sizes, say below 50

Jan 1, 1989

By Thomas A. Gwynn

When Lewis and Clark first pushed their boats up the Missouri River, Meriwether Lewis reported the presence of coal in the western states by saying in 1802 that it "burnt tolerably well and afforded but little flame or smoke but produced a hot and lasting fire". Lewis would have been amazed and bewildered at the history of coal development in this region and the more recent political-socio-economic-environmental confrontations of today. Certainly without this coal the railroads would not have readily pushed into our western states, and the progress of this region would have suffered. The coal industry has passed from a period when "coal was king" to a period of depression in the industry, but its importance is being revived. A contributing and simultaneous environmental concern has emerged in the nation and in many states during the past ten years, partly caused by newly imposed standards for sulfur content of fuels. Much of the midwest and eastern coal cannot be used because of high sulfur content, shifting attention to the low sulfur coal deposits of the western states. In the western states, lands disturbed by strip mining or even underlain by strippable coal are small compared to the total acreage, and usually mining operations are on lands not under cultivation. There are some farm lands being disturbed by surface mining, but this is often over-emphasized. In states like New Mexico and Arizona the percentage is less. The value of the minerals underlying the surface certainly must be considered along with the value of the surface, and sometimes proper reclamation following mining can result in higher ultimate usage of the land.

Jan 1, 1974

By William D. Meakins

INTRODUCTION Today, auxiliary fans, or boosters as they are sometimes called, are commonly used underground to provide ventilation for safe working conditions for personnel. Fans are installed in many ways and for many purposes; however, their use falls into three main categories depending upon the application. Auxiliary Face Ventilation For Coal Mines Usually the application of auxiliary fans underground in coal mines presents problems not normally encountered in other types of mining. Two of the major problems deal with liberation of methane at the coal face and the production of coal dust in the mining process. For these conditions it is necessary to use permissible (explosion-proof) type of equipment. As a result, these fans are discussed in a category by themselves. Auxiliary Fans For Tunnel and Drift Ventilation Tunnels and drifts present unique ventilation requirements. For instance, tunnels and drifts can be developed for considerable distances into virgin territory. Since they are generally dead-ended, the only way to obtain ventilation at the face is to use ventilation pipe to establish one leg of a ventilation circuit. The ventilation of tunnels and drifts therefore falls into another natural category. Other Uses of Auxiliary Fans For Mining Purposes Fans can be applied to mining applications in many ways other than those discussed under the other two categories. For example, many times auxiliary fans can do a much more practical job of proper air control and distribution that can be achieved with any other mechanical means; therefore, these other uses are discussed as a special category. AUXILIARY FACE VENTILATION FOR COAL MINES After 1936, federal and state coal mining laws prohibited the use of auxiliary underground fans in coal mines since such equipment had been widely misused. In certain cases, recirculation of face air had been allowed to occur thereby creating a serious potential explosive hazard by the possible buildup of excessive methane concentrations. By the late 1950s, mining machines with rapid face penetration were commonly being used in coal seams which liberated higher quantities of methane than in earlier years. As a consequence, in the late 1950s and early 1960s, the use of auxiliary face fans was again allowed under strict experimental conditions because conventional methods of face ventilation control without fans were becoming inadequate. Today, auxiliary face fans are widely used under strict federal and state control. Such auxiliary ventilation does not reduce the need for the amount of primary air from the main mine fans; however, it does help to distribute primary air more efficiently at the face. The present trend is toward an exhaust system of ventilation utilizing 406- to 610-mm (16- to 24-in.) diam tubing extending from the face to an outby auxiliary fan. Since the tubing is normally applied with negative pressure, spiral wire reinforced tubing has been replaced largely with metal and, more commonly, fiberglass tub¬ing. Additional auxiliary blower units are often used at the mouth of the room being developed, or installed on the miner or loader near the face, depending upon the amount of gas liberation present. Often one (or more) of the fan units is equipped with an integrally mounted hopper and feeder which automatically adds a continuously metered amount of rock dust to the exhaust air. The combination unit tends to make the mixture of discharge particles noncombustible and reduces to some extent the need for additional rock dusting of return airways. In this part of the chapter, typical auxiliary ventilation systems are described including curves and photograph of typical/applicable equipment. Reference will be made to "blowers" and "ex¬hausters." Both are fans and are basically the same units. They take on their name through the manner in which they are used. A blower usually has an inlet bell on the inlet side to help to obtain good air flow into the blades. An exhauster often has a discharge cone added to reduce the discharge loss. Any basic fan unit can be used either as a blower or an exhauster. Description of Auxiliary Ventilation Systems Several auxiliary ventilation systems and modifications of basic systems have evolved over recent years. Some of these systems are described and illustrated. System No. 1, an exhaust system for faces with comparatively low gas liberation, is shown in Fig. 1. Here

Jan 1, 1982

By Stanley C. Suboleski, C. B. Manula

INTRODUCTION In any mining operation all possible steps should be taken to increase efficiency. One area for improvement is mine planning and design, particularly in the area of equipment selection for room-and-pillar systems. Be- cause of the availability of a wide variety of face machines, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, this choice must be made on the basis of quantitative facts and forecasts related to the mining application. The purpose of this section is to develop and analyze the details of the mining process. Some specific areas studied include the relationship of system design to productivity, suboptimization as a result of equipment changes, and measurement of system performance. The plan of work leading to a quantitative description of these study areas is based on the growing interest in total system design using simulation as an analytical method (Manula, 1963). CHARACTERISTICS OF PRODUCTION OPERATIONS FROM ROOM-AND-PILLAR SECTIONS For a given mining method, raw production in a given section of a mine is primarily dependent upon the coal seam thickness, roof and floor conditions, methane emission, the mining methods, and the man-machine element. Average section production varies from 300 to 800 st per shift for conventional and continuous mining in high seams and from less than 100 to 300 st per shift in low seams. Since the reject varies from 0 to 40%, these figures must be decreased by the appropriate percentage to reflect the amount of clean coal mined. Personnel requirements per production section per shift for the various methods are listed in Table 1. Table 1. Production Personnel Method No. Method No. Conventional 12-1 5 Longwall 9-14 Continuous 9-1 2 Shortwall 9-12 MINING VARIABLES To evaluate the constraints and interrelationships for various mining methods, it is necessary to categorize the variables which underlie system production potential. Seven critical independent variables which determine production can be identified and categorized (Suboleski, 1978) : Seam Height The five categories are as follows: less than 36 in.;. 36 to 55 in.; 55 to 100 in.; 100 to 180 in.; and greater than 180 in. Floor Quality Floor quality ranges from : Excellent: Smooth, hard, grades less than 1 to 1 % % , and dry. Good: Smooth, soft but dry, with grades less than 3 % . The floor will deteriorate, but cautious operation can prevent it. There may possibly be heaving at some later time. Fair. Soft and damp. There is occasional interference with equipment operation; requires the use of four-wheel drive shuttle cars; ruts with regular use, and may have adverse grades of 5 to 7%. This may be coupled with slippery bottom and/or occasional steep rolls. Poor: Soft and wet. Requires blocking of the bottom to support equipment. There are frequent steep rolls and grades in excess of 7%. Roof Quality Roof quality ranges from : Excellent: Men are able to work under the unsupported top during the initial production cycle if legally permitted. Good: The roof is bolted on a 4 x 4 or 5 x 5 pattern with short bolts (442 in.) or <seam height if the seam >42 in., or requires posting with no bolts on a 4 x 4 or 5 x 5 pattern. There are no falls. Average: The roof is normally bolted on a 4 x 4 or 5 x 5 pattern, but with long bolts (>seam height or >6 ft.). There are infrequent minor falls or there may be an excellent roof which is difficult to drill. Fair: This type often requires spot bolting in addition to the regular pattern or bolting with planks. The roof conditions require shorter than planned cuts, or narrow cuts. Poor: This type requires bolts plus crossbars and posts, or installation of yielding supports or truss-type support. It is almost certain to fall if this is not done. Methane Liberation This ranges from none detected to low (no buildup at the face, even with minimum ventilation requirements) to moderate (the curtains must be extremely tight and tubing close to the face or methane will build up to 1 % during the loading of the car) to high (methane will build up to 170 if the miner is operated at the normal rate, even with proper ventilation). Hardness of Coal Coal hardness falls into the following categories: Soft: Soft coal is easily cut by a continuous miner. A plow could be used by longwall. Average: Coal of average hardness could be easily cut by a miner, and a shearer would be used in the longwall. Moderate: Moderately hard coal causes difficult cut-

Jan 1, 1982

By G. A. Irdi

An automated method of microscopy for determining the pyrite size distribution on two base coals that were crushed to 28 mesh x 0 has been developed. Polished epoxy-bound coal pellets were prepared and examined by a Zeiss IBAS image analyzer utilizing a program developed from provided software. Pyrite size distribution determination is considered a necessary first step in pyrite characterization that could lead to successful predictions, by microscopy, of a coal&apos;s theoretical pyritic sulfur removal. Our research efforts to date have indicated that the IBP-S can be a reliable instrument for determining pyrite size distribution in crushed coal. A program was also developed to convert pyrite size data to a weight basis for comparisons to the results from chemical analyses. The problems encountered in our research and their solutions will be presented in the discussion.

Jan 1, 1986

By D. E. Piggott, B. E. Hartmann

The thought of constructing an intake shaft five miles from the shore and 142 feet below the surface of Lake Huron from the bottom up sounds like a questionable venture. Why would one want to raise a shaft from the bottom at the end of a 16 foot diameter, six mile long tunnel to within six feet of the bottom of Lake Huron? The answer lies in the fact that Lake Huron is seldom a tranquil lake. The construction period and workable days from the surface are limited. Two previous attempts to construct this intake shaft by conventional means had been thwarted by lake storms. These approaches were circular sheet-piling cofferdams with the intention of sinking a 30 foot OD, five foot wall thickness concrete casing in the center. However lake storms, particularly in the months of November and December, proved disasterous. The last attempt was halted in December 1970 when three of the seven circular cofferdams on the north side were destroyed by pounding waves. Then, due to the nature of the technical difficulties and limited construction schedule time, it seemed desirable to devise a way in which construction could proceed without being too lake-sensitive. Obviously, if men could work from the tunnel and proceed upward toward the bottom of the lake, not having to worry about the soil collapsing and bringing the lake in on their heads, the construction would be unimpeded by adverse weather. The answer to this, however, required techniques beyond the ordinary. Approximately two years previous to the start of this shaft, nine shafts had been efficiently constructed on the same project site

Jan 1, 1974

By J. B. Gwiazda

S. Budirsky J.B. Gwiazda&apos;s article deals with an interesting problem that has not been studied thoroughly up to now. Gwiazda has proposed a technical solution that eliminates horizontal load imposed by the supports on the roof. That load is due to a discrepancy between the trajectories of the canopy and the overlying strata. It is true that the improved lemniscate guidance system proposed by Gwiazda could eliminate the horizontal load but, on the other hand, it would represent a higher cost of the supports, and it would complicate the already complicated mechanism of powered supports. That is why we must be convinced that the proposed improvement is actually needed. From that point of view, the following questions should be elucidated. As shown in Fig. 1, the point 0 travels along the curve a, which produces horizontal load on the roof in the direction of the coal face. As stated by Gwiazda, "such a high load is capable of destroying the roof above the support, causing rock debris to be scattered around the face." The results of our measurements carried out in coal mines of the Czechoslovak part of the Upper Silesian Coal Basin show that the convergence in the modern type of powered supports does not exceed several millimeters (not more than 10) per hour. Similar conclusions were drawn from field measurements performed in the Polish part of the Upper Silesian Coal Basin (see S. Romanowicz and H. Szopka in Proceedings, Scientific and Technical Symposium Simmex&apos;85, Katowice, Poland, pp. 73-83). The small vertical closure of the supports also induces a small horizontal displacement of the canopy. In addition to this, the transmission of forces between the roof and the canopy is influenced by the layer of debris on it, i.e., the canopy slides without imposing a greater horizontal load on the roof. This was deduced from field measurements of Voest-Alpine F 4/4500 powered supports equipped with rams instead of the common front lemniscate links (denoted as 1 in Fig. 5). In these supports, the pressurizing of the space of piston rod (1a in Fig. 5) causes the rams to close, which induces horizontal load on the roof in a direction toward the coal face. After the setting of a support unit, the pressure in the piston rod space was found to drop, frequently to zero, because the small horizontal sliding between the canopy and the debris or inside the debris caused the horizontal reaction from the roof to fall to zero, although the debris were pressurized by vertical setting load. As a consequence, there was no horizontal load imposed by the canopy on the roof. A rise of the horizontal load was recorded only after the passage of the shearer and during lowering of the adjacent units. Thorough information on the results of the aforementioned field measurement is given in the paper, "Analysis of the performance of shield powered supports installed in a thick seam," published in Mechanizacja i automatyzacja gornictwa, 1982, No. 12, pp. 38-46. An English translation of the paper is available from the author. We have deduced from our observations that horizontal load imposed by the canopy on the roof in the direction toward the coal face is useful for roof control because it limits the displacement of the immediate roof toward the gob particularly during the rise working. We came to the conclusion that horizontal load on the roof toward the coal face should be induced on purpose. Could Mr. Gwiazda prove with the results of field measurements his contrary opinion? Has the small horizontal displacement of the canopy toward the face actually had an adverse effect on the roof? As shown in Fig. 2, during the setting of a support unit, the canopy imposes a horizontal load on the roof in the direction of the gob. In this case, I share Gwiazda&apos;s opinion that the horizontal load could have an adverse effect on the roof. Nevertheless, two important circumstances were neglected - the horizontal compliance of the supports and the interaction of adjacent units. The question of the compliance was analyzed precisely by I. Krumnacker in Gluckauf-Forschungshefte, 1984, No. 5, pp. 219-223. He found that due to the clearance between the hinge pins and the eyes of the sheild and due to the elasticity of the steel structure,

Jan 1, 1987

By Gregory P. White

A number of private companies and universities have developed computer programs which can be used to simulate surface coal mining by dragline. In this paper, we briefly discuss the concept of computer simulation, compare these computer programs with each other, describe the major changes required to convert these programs to an IBM computer system, and analyze their sensitivity to inaccurate input data. We also present a summary of the required data input for each program, core storage requirements, and output results. Sources for obtaining these programs and their documentation are listed at the end of the paper.

Jan 1, 1983

By Steven J. Stokowski, Frederick M. Bodycomb

This chapter deals with the use of industrial minerals in insulating materials used to control our thermal and acoustical environment. There are numerous products on the market used for thermal and acoustical insulation; they consume substantial quantities of a variety of industrial minerals. Following is a brief review of the theory and function of insulating materials. Acoustics is the science of sound, and architectural acoustics deals with sound in buildings. If this definition is broadened to include transportation vehicles, it is this end use for which acoustical insulations are primarily manufactured. Sound is defined as the auditory sensation in the ear, or the disturbance in a medium which causes this sensation. Acoustical insulation is used to reduce or eliminate noise, defined as unwanted sound. Noise control may be accomplished by the reduction of sound radiation at the source, by utilizing sound reducing construction methods such as staggered studs, etc., to control sound transmission, or by using sound absorbing material on walls, ceilings, and floors (Rossing, 1985). Acoustical insulation functions by absorbing the energy in sound waves in a porous material. As the sound waves penetrate the pores, they are dissipated by reducing the amplitude of vibration of the air molecules by contact with the pore walls, with subsequent conversion of the sound energy to heat energy. Acoustical insulation is generally highly porous, 1.3 cm or greater in thickness, and has interconnected pores. Acoustical insulating materials include fibrous vegetable or mineral matter and cellular organic and inorganic material, such as natural or manufactured foams (Sabine and Moulder, 1979). Acoustical materials are most commonly porous boards and tiles, which are often composite materials with perforated facing. Roof insulation board and lightweight concrete can also contribute to the absorption of noise. Thermal insulation is defined as material used to control the flow of heat. It may be used for heat control from low cryogenic temperatures (below -100°C) to in excess of 2 200°C for applications such as ablative shields for spacecraft. Heat transfer occurs by conduction, convection, or radiation. Conduction is the transfer of heat without the movement of the conducting medium, as through a metal. Heat convection through a liquid or gas takes place by movement of the medium. Forced convection is the basis for heating and cooling equipment, utilizing pumps or blowers to transfer the thermally conditioned fluid. Free or natural convection occurs due to density differences in the fluid. Radiation is the transfer of energy in space (Eckert, 1985). Conduction of heat through a solid is reduced by insulating the body with foams, or fibrous or small celled granular material. Heat transfer through a gas (convection) is controlled by creating many small pores which inhibit the movement of the fluid, substituting a gas of low thermal conductivity, or evacuating the space. Heat radiation can be reduced by the use of materials that reflect or absorb the energy (Glaser, 1967). Thermal insulating materials may be vegetable or mineral fibers, organic or inorganic particles, or foams with small pores, generally used to form a low density thermal barrier. They may be blocks, poured lightweight cementitious materials, bricks, etc.

Jan 1, 1994

By S. Yap, F. J. Sotillo, L. P. Irwin, F. M. Utsey

Slimes, especially clays, are detrimental to several processes in the Mining Industry. The efficiency of classification, clarification, gravity separation, and flotation decreases significantly in the presence of slimes and clays. This problem is particularly critical in the Phosphate and Sulfide Industries. To reduce the effect of slimes in mineral processing, several desliming techniques and chemical additives are used, such as sodium silicate, sodium carbonate, sulfuric acid, tripolyphosphate, hexameta phosphate, etc. Lately, the Mining Chemical industry has shift to more “Specifically Developed” reagents that offer the most efficient and cost effective performance, mainly using organic polymers. For this purpose, the Mining Chemical Industry needs to understand the crystal chemistry of minerals, the chemistry of the aqueous media, the interactions in solids-aqueous-gas interfaces, the rheology of the system, and the plant operation conditions and parameters. This paper describes the use of surface chemistry fundamentals on the design of an organic polymer capable of modifying the rheology of clayish slurries of a phosphate ore. The change in the rheological characteristics of the clayish phosphate slurries allow fine ore particles to settle faster by reducing the slurry viscosity. Thus, abetter separation of the ore from the slimes is possible using gravitational or centrifugal forces. As examples of the application of this reagent, industrial and pilot plant tests on desliming using tanks and hydrocyclones are presented. These tests showed the reduction of 32%-36% in ore losses for different phosphate ores during desliming operations, and the increase of cyclones desliming efficiency to 80%. Tests were also carried out to improve the rejection of unwanted iron bearing slimes in phosphate feed. These tests demonstrated that it is possible to reduce by 0.25%-1.23% Fe2O3content in the flotation feed product. As a result, significant economical benefits are observed with the use of this new technology without any adverse effect on down stream operations, such as clay settling or phosphate flotation.

Jan 1, 2003

By Kadri Dagdelen, Thys B. Johnson, Salih Ramazan

Long-term production scheduling design is a very important part of mining because it determines the economic outcome of a project There have been many attempts to solve the optimum pit scheduling problem, but there has been no success in developing a scheduling method to give optimum results in maximizing net present value of a mining project. Open pit production scheduling problem can be formulated as a mathematical programming problem and solved using Mixed Integer Programming technique. However, it is not possible to solve the formulation within a reasonable time since the number of integer variables required for the mathematical model is too great to do that by today&apos;s available computer technology. There- fore, a methodology is required to combine, or aggregate, the mining blocks and to decrease the number of integer variables in scheduling without losing the optimality. Therefore, the fundamental tree concept was developed in this paper to combine the blocks. A fundamental tree is defined as any combination of blocks such that: 1. the blocks can be profitably mined, 2. the blocks obey the slope constraints and, 3. there is no subset of the chosen blocks that meets 1 and 2. A Linear Programming (LP) formulation is developed as a mathematical model to find a set of fundamental trees that exist for a deposit. Since the blocks are combined to form the fundamental trees, the number of variables required for the scheduling model is decreased significantly. This decrease in the number of variables makes it possible to mathematically formulate the multi-time period scheduling problem as a Mixed Integer Programming (MIP) model. A case study is performed on a multi-mineral copper deposit in Peru, South America. NPVs of annual after-tax cash flows generated based on the schedule provided by the "Fundamental Tree Algorithm" is compared with NPVs resulted from the schedules coming from three of the computer packages presently available to the mining industry. These are Mintec&apos;s M821V, Earth- work&apos;s NPV Scheduler, and Whittle&apos;s Milava open pit mine schedulers.

Jan 1, 2002

By John Mastoris, Shkurta Gashi, Kostis Dragasakis, Kostas Kouklidis, Halil Berisha

Water is increasingly recognized as a critical issue for sustainable development, becoming as important as carbon to corporate responsibility and reputation. Although the cement industry’s overall ‘water footprint’ is relatively small compared to other sectors, the Cement Sustainability Initiative of the World Business Council for Sustainable Development (WBCSD/CSI) has recognized the importance of water and the need to take actions towards efficient water management, with developing standardizing practices and employing a risk-based assessment approach, mostly at local level where individual facilities and activities can have implications for other water users in the area. Sharrcem, a member of the Titan Cement Group, has made significant investments to upgrade its production facilities, the technological process and apply environmentally friendly technologies. Under this frame, Sharrcem implemented a project for the construction of a Waste Water Treatment Plant (WWTP) in the Cement Plant facilities, which has been successfully operating since early 2016. This paper discusses the technology applied at the new WWTP and the results achieved already, with significant improvement in the quality of the treated water, as compared to the previous situation where untreated wastewater was directly discharged to the nearby Dimce Stream. The WWTP project is a major investment of Sharrcem that aims to improve the quality of the discharged water effluents and thus prevent potential river pollution and overall protect the environment and the health of Sharrcem employees and local community. The WWTP operates with the Sequencing Batch Reactors (SBR) technology, is fully automated and has been also connected with few households of the neighboring community to treat also their sewage water. The plant can be expanded in the future – to connect with additional households - without increasing the size of the treatment tanks. One of the benefits of this project is that by removing a variety of contaminants from water it becomes usable again, depending on the nature of the contaminants and the end use of the water treated. According to the monitoring results the treated water that comes out of the WWTP fully meets quality requirements according to the EU and local limit values standards

Jan 1, 2017

Introduction The objective of the design and operation of a mine is to make as much money as possible within certain reasonable and responsible constraints. The imposition of constraints on the objective of maximizing profits can result in an optimum mine design. This paper deals with the maximization of profits. Optimization will be discussed in a future paper. In the mining industry, it is generally accepted that the maximum economic recovery is defined by identifying the reserves and the sequence of mining that results in maximum net present value (NPV) or discounted cash flow-rate of return (DCF-ROR), as indicated in Fig. 1 (see Lemieux, 2000). Current parametric analyses techniques, such as varying the mining costs; profit reservation; sales price or metal content, to define pit limits and mining sequence technically referred to single, double or triple parameterization, do not assure that the curve in Fig. 1 will be maximized. In defining the sequence, the first material to be mined should be the first grouping of recoverable mineral that has the highest after-tax unit value and that forms a feasible mining unit. The assumed mining of the first pit should be followed by the assumed mining of the second most profitable and practical pit or pit expansion. If this process of grouping and sequencing is followed until the profitability approaches zero, the general sequence required to extract the maximum economically recoverable reserve is identified. The curve in Fig. I is constructed by calculating the NPV for a series of sequences, each assuming operations are terminated on successively lower profit pits. If the operation ceases on a pit with too high of a profit, opportunity is lost, and the NPV is lower than the maximum. The NPV curve peaks and then starts to decline before the zero-profit pit is assumed mined. This occurs because the money invested in advanced stripping would have produced a greater return if it was invested at the dis¬count rate. The maximum economically recoverable reserve is defined by the pit limit corresponding to the maximum NPV or DCF-ROR. Pit and phase definition The real challenge of reserve definition is identifying the phasing and after-tax profit per ton, so that the curve in Fig. 1 can be plotted. The after-tax profit cannot be properly addressed until after the pits are designed, the production is scheduled and the cash flow is estimated. Throughout the years, many investigators have ad¬dressed this problem. A major thrust of the famous paper in which Lerchs and Grossman (1965) presented their algorithm was to identify a sequence that would produce a result similar to that identified in Fig. 1. Whittle&apos;s (1988) four-dimensional analysis is designed to address this issue. The author addressed this same issue in a paper presented to the 1968 Canadian Institute of Mining national convention (Lemieux, 1968). Without a relatively simple methodology to con¬struct the curve in Fig. 1, the number of iterations in a trial-and-error method becomes prohibitively burden-some. The pit designer seeks a simple pit-planning parameter that will serve as a proxy for the after-tax profit per ton used in defining the curve in Fig. 1. The designer&apos;s goal is to apply this pit-planning parameter using standard pit-wall location techniques to design a series of pits that will provide a guide to the sequencing. Common techniques used to position pit walls are strip-ratio limits, highwall incremental analysis, floating-cone methods or "maximizer" applications1. Costs, revenues, noncash charges, taxes and profits are usually structured on a unit basis for use in the pit-wall location analysis. Application of the proxy parameter using the pit-design tools should, ideally, result in the definition of pits and sequences that will maximize the curve in Fig. 1. 1 The pit-design tool frequently referred to in the literature as an "optimizer" defines a pit boundary that maximizes the value contained within based on the input parameters and the safe pit-wall angle. The optimization of the pit design involves selection of rate of production, cutoff grade, product quality and other considerations. These considerations constrain the maximization of value. Therefore, pit-design tools that maximize value should be called "maximizers."

Jan 1, 2000