Search Documents

By J. W. Powell

Several years prior to 1962, it became obvious that in order to develop ore reserves below the Storke Level, it would be necessary to devise a method to facilitate the ore being lifted three hundred feet to the surface or six hundred feet to the mill. The final plans called for an underground crusher complex with two stages of crushing and a conveyor belt gallery for transport of the ore six hundred feet above, to the third crushing stage. Access into the area was gained in 1962, by sinking Five Shaft approximately one quarter mile southwest of the proposed complex site, and drifting into the area. Collar elevation of Five Shaft is three hundred feet above the 600 Level Crusher Complex. All muck was loaded into ten-ton granby cars, hoisted to the surface and dumped. (See Figure 1 for the relationship between Five Shaft and the Crusher Area) Drifting into the Crusher Area contunued until 1965 at which time the Crusher Room Cutout was started. The Crusher Access Drift (CAD on Figure 2) war driven and mining pm- ceeded according to the description on drawings marked Figure 3a and 3b. After the arch portion of the Cutout was excavated and concreted, removal of the center "pillar" commenced. This muck was removed with an Eimco 123C crawler-mounted front-end loader. (See Figure 4) A total of 576,000 cubic feet of rock was removed from the Crusher Cutout. All sup- port was afforded by grouted roofbolts on a specified pattern, as shown in Figure 3c. Crane support columns were put into place and held by braces welded to roofbolt heads. Sidewalls and endwalls were formed and concreted. (See Figure 5 for the finished product)

Jan 1, 1970

By Gerald C. Smith

Introduction Newmont Mining Corp.'s Carlin Gold Mining Co. mines gold ore and waste material from four open-pit mines in Northeastern Nevada. Combined production rate is 24.5 Mt/a (27 million stpy). The company is producing gold bullion from the 2.4 kt/d (2600 stpd) Carlin Mill No. 1. and the 2.3 kt/d (2600 stpd) Maggie Creek heap leaching plant. In August 1985, the 6.3 kt/d (7000 stpd) Carlin Mill No. 2 at Gold Quarry came on-line. The total combined throughput of 11.2 kt/d (12,000 stpd) will make Carlin Gold Mining one of the largest US gold producers. Feasibility studies are underway to increase the total gold out-put from Gold Quarry. This will be done by adding a continuous dump-leaching process that will recover gold from lower grade ore. History In 1961, Newmont exploration geologists located claims in the Lynn Creek mining district near Carlin, NV. An exploration drilling program revealed significant gold mineralization. A stepped-up drilling program revealed an ore body with an estimated 10 Mt (11 million st) of ore containing 109 t (3.5 million oz) of gold. Test results in 1963 allowed metallurgists to develop the flowsheet and design for a 1.8-kt/d (2000-stpd) countercurrent decantation (CCD) cyanide plant. Carlin Gold Mining Co. was formed to operate the property. Carlin purchased its first mining equipment in 1965. This consisted of two Bucyrus-Erie 2.7 m3 (3.5 cu yd) shovels and nine 27.2 t (30 st) Wabco Haulpak trucks, two Inger¬soll-Rand track-mounted drills, one Chicago Pneumatic T-650 rotary drill, one rubber tired Michigan 280 dozer, one Caterpillar D-8 36A track dozer, one Caterpillar 16 motor grader, and the necessary ancillary equipment. The fleet was capable of mining 3.2 Mt/a (3.5 mil¬lion stpy) working two eight-hour shifts, five days a week. In 1967, one P&H 1500 3.8 m3(5 cu yd) diesel electrical shovel and three 59 t (65 st) Dart trucks were added to the fleet, along with a Chicago Pneumatic rubber tire mounted rotary drill. This equipment addition increased the mining capabilities to 5.7 Mt/a (6.3 million stpy). Three separate pits, the Main, East, and West, within a 1.6-km (1-mile) radius of the Carlin mill were being mined. The crew consisted of 46 hourly men and three supervisors. This equals 497 t/ total hourly manshift (548 st) or 407 t/total manshift (515 st). Rising gold prices in the early 1970s allowed lower grade deposits to be mined at greater distances from the mill. The Boot-strap pit, 19.3 km (12 miles) north of Carlin, was started in 1973. Two Hough 45.4 t (50 st) front-end loaders, four Wabco Haulpak 45.4 t (50 st) trucks, and a second track type D-8H dozer were added. The higher grade ore was trucked to the Carlin mill using three

Jan 11, 1985

By R. Woods, J. D. Wright

INTRODUCTION The Endako deposit was first explored in 1926, but development waited until the early nineteen sixties. It first came under the control of Placer Development in 1963, and early in 1964 a decision to bring it into production was reached. The deposit is located near the geographic center of British Columbia, and is served by an east-west communication system including a paved highway, mainline railway and good telephone, teletype, and computer facilities. The plant area is shown in Figure 1. The operation is known as the Endako Mines Division of Canex Placer Limited of Vancouver. First production was achieved in June, 1965, at a nominal rate of 10,000 tons per day, but it soon was closer to 15,000 tons per day. In 1967, two new grinding and flotation sections brought capacity to the present rate of approximately 27,000 tons per day. With mill heads of around 0.15 percent MoS2, production is about 14,000,000 pounds of molybdenum per year. A flowsheet of the operation is given in Figure 2. A legend for this flowsheet is given in Table 1. Published ore reserves are estimated at 214,500,000 tons at an average grade of 0.143 percent MoS2. PRIMARY CRUSHING The 85 or 100-ton haulage trucks dump over a grizzly into a 42 inch x 65 inch C.A.C. (Canadian Allis Chalmers) gyratory crusher.

Jan 1, 1976

Potassic alteration domains of greenstone belt lode gold deposits are characterized by systematic partitioning between different groups of incompatible elements, such that Al, Ga, Th, U, Ti and V are decoupled from K, Rb, Ba, Cs and Tl. The former group of elements have concentrations and interelement ratios in alteration domains which reflect host rock control, implying approximately isochemical behaviour. In contrast, K, Rb, and Ba are strongly coenriched, and linearly correlated over th4ee orders of magnitude in abundance, where K/Rb = 260, and K/Ba = 40: K/Cs (-10 ) and K/T1 (-2x10 ) are also correlated, though more weakly. Lithium abundances, and Rb/Sr ratios are erratic in altered rocks. These interelement trends, collectively, are present in deposits variously hosted by ultramafic, mafic, or felsic volcanic rocks, and sediments or granitoids.

Jan 1, 1988

By Ray Brainard

Treated effluent from the Clean Water Coalition (CWC) member agencies is currently discharged at an annual average rate of 6,570 l/s into the Las Vegas Wash, and is increasing annually. As the effluent flow increases, the nutrient loading of the treated effluent will approach the maximum limits allowed under the current regulations. To manage this flow while maintaining water quality in Lake Mead, the CWC is implementing a 44-km-long conveyance system. This paper discusses the geological and geotechnical aspects of the 13.4-km-long tunneled section through the River Mountains and their effect on design. The tunnel alignment traverses a heterogeneous package of volcanic and sedimentary rocks exhibiting widely variable rock conditions.

Jan 1, 2008

By J. R. Sims

Gold assays from production blastholes in the Mercur Hill Pit were used to delineate known ore zones and to determine how well previous exploration drilling defined these zones. The most important factors causing inadequate ore zone definition were: 1) inappropriate location of drill holes relative to the ore zones, 2) presence of stopes from previous mining, 3) sampling and assaying errors, and 4) smoothing of the ore zone boundaries during ore reserve estimation. Infill drilling strategies were evaluated to determine the efficiency with which a given drill pattern defined the known ore zones. A drilling strategy was developed which improved ore zone delineation when compared to techniques which maintained uniform drill spacing.

Jan 1, 1992

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

By W. K. Wedge

The chemical composition of the Pennsylvanian Bethany Falls Limestone Member of the Swope Formation was investigated using optical emission spectroscopy and both flame and flameless atomic absorption spectroscopy. Elements determined were Ca, Mg, Fe, Mn, AI, Si, Na, K, P, Ti, Zn, Cd, Ni, Co, Cu, Pb, Cr, V, and Mo. Over 100 samples were collected from active quarries along a 320-km-long (200-mile) outcrop in northwestern Missouri. Intervals were sampled representing uniform lithology to determine vertical and lateral geochemical variation. The Bethany Falls Limestone is the most extensively quarried Pennsylvanian limestone in Missouri. In 1975, 42 active quarries produced almost 5.4 million tons (6 million st) of stone valued at over 15 million dollars.

Jan 1, 1977

By Daniel J. Dobbels, Eric R. Drooff, James R. Wheeler

Construction of Boston’s C11A1 Section of the Central Artery (I-93)/Tunnel(I-90) Project beneath the existing MBTA Red Line Subway at South Station required excavation to depths in excess of 33.5 m (110 ft) through permeable sand and gravel subject to almost 27.4 m (90 ft) of hydrostatic groundwater pressure. As tacked drift tunnel underpinning system was designed to provide positive support to the active station prior to mainline tunnel construction. As part of this system, a permeation grouting program was developed to facilitate tunnel excavation. This paper describes the design and implementation of the grouting program, in sit testing, and the overall performance of the grouted soil mass.

Jan 1, 1999

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The U.S. Bureau of Mines and AMAX Coal Company have studied surface coal mine overburden blasting near four steel and one PVC pipe-line of 15 to 5l-cm diameter, monitoring vibration, strain, and pressure. Unlike tests simulating construction blasting, these were up to 1000 kg per delay in 3l-cm blastholes. Worst case comparisons showed that 12.7 cm/s blasting vibrations produced strains about 1/4 that of pressurization and 10-18 pct of the ultimate tensile strength. No failures occurred from blasting as close as 15 m which produced vibrations over 60 cm/s.

Jan 1, 1994

By Stephen P. E. Redmond

A 15 km water supply tunnel is being constructed in Buenos Aires, Argentinata expand the capacity of the existing system. Two 4.3 meter diameter Earth Pressure Balance (EPB) tunneling machines operating at times from the same shaft on a congested work site and advancing through sedimentary deposits underlying this wonderful city pose interesting challenges. As of January 1999approximately 50% of the tunnel has been excavated. Combined machine production rates of 1026 m/month have been achieved. Presentations made in prior proceedings can be referenced for details of the overall Project scope and for details of the tendering process. The purpose of this paper is to compliment those presentations by addressing now the execution of the work.

Jan 1, 1999

By Richard J. Fantel

The U.S. Bureau of Mines performed engineering and economic analyses on 130 domestic phosphate mines and deposits, all containing demonstrated resources, of which 73 are in the Southeastern states of Florida and North Carolina, to determine the domestic availability of phosphate rock. Of the total domestic resources studied (6.4 billion tons of recoverable rock) over 60 percent is found in these two Southeastern states. At an estimated cost of $30 per ton, in January 1981 dollars, approximately 1 billion tons of rock is potentially recoverable from Southeastern deposits, increasing to 3 billion tons at $45. In addition, there is nearly 6 billion tons of recoverable rock at the inferred level (some presently unmineable) in Florida and Georgia.

Jan 1, 1983

By W. L. Chen

In the United States hydraulic cyclones have been used for thickening, classification and cleaning in coal preparation plants for many years. The cleaning cyclones presently in use are based on using a "heavy medium", such as a fine magnetite and water pulp. The latest addition to cleaning cyclones is the one which uses ?water only?, or simply called "Hydrocyclone". Just as was the heavy medium cyclone, the hydrocyclones were originated in the Netherlands (1, 2). Plants using hydrocyclones were built in Europe (3) and test plants were erected in Canada (4, 5, 6) and India (7). Roberts and Schaefer Company has built four plants using hydrocyclone circuits. One additional plant is in the process of construction.

Jan 1, 1965

By Paul Cameron Gilmour

Geologically, as distinct from economically, "porphyry copper (molybdenum, gold, silver, etc.) deposits" might be defined as large, disseminated and/or stock-work occurrences of copper-minerals, generally averaging less than 1 per cent cop-per. They are normally associated with small plutons which range in composition from granite to diorite, although, typically, they consist of quartz monzonite or granodiorite. Circumstantial evidence indicates that these "minor" granitic intrusions may represent the intrusive phases of post-orogenic, calc-alkaline volcanism, this conclusion being suggested by: 1. Texture and grain size. 2. Prevalence of intrusive breccias. 3. Relationship to unconformities and estimated depth of emplacement. 4. Spatial distribution in relation to orogenic zones. 5. Age of mineralization and igneous episodes

Jan 1, 1972

By L. B. Bramlett

The Archean (2.65 b.y.) aged Canning Stock at Copper Mountain, Wyoming contains an average of 20 ppm U. The North Canning and Fuller deposits occur within the enriched interior of the stock. Post-Laramide development of super gene enrichment blankets occurred in wide (25- 100 m) crushed zones. Hematite and chlorite accompany pyrite and sooty pitchblende in the mineralized zones. Reduction mechanisms proposed for deposition of pitchblende are: 1) sulfides, 2) hydrocarbons, 3) bacteria, 4) the water table, or 5) some combination of these. Abundant tar- type organics appear to have preserved the enrichment blankets from degradation. Trace element and radiometric data define target zones, but exploration models focus on favorable structure.

Jan 1, 1980

By Nicholas Kyriazia, John P. Shubilla

A performance study of oxygen self-rescuers of varying durations from the United States and other countries was undertaken as an assessment of present worldwide technology. The apparatus were tested on a Breathing and Metabolic Simulator in the Life Support laboratories of the Bureau's Pitts- burgh Research Center. Parameters monitored during the testing were inhaled levels of C02, 02, inhaled gas temperature, and breathing resistance. The metabolic demand placed on the apparatus represented the average demand of the 50th percentile miner performing a 60-min man-test 4, as described in 30 CFR 11H. Results presented include apparatus service life and subjective comments as well as averages and peaks of monitored parameters.

Jan 1, 1986

By Peter L. Hofmann

Significant quantities of nuclear wastes were first generated in 1944 as a byproduct of the national defense program. To establish the current inventories and future projections of nuclear waste products is not a simple task. The Oak Ridge National Laboratory recently issued a report which now constitutes the official basis for nuclear waste inventories and projections. Radioactive wastes originate from five major sources (U .S. Department of Energy, 1980b) : (1) From the commercial nuclear fuel cycle related to the production of electricity , (2) From defense related activities, (3) From institutions such as hospitals, universities, and research foundations, (4) From industrial uses of radioisotopes, and (5) From mining and milling of uranium ores.

Jan 1, 1981

By R. L. Frederking

Geological remote sensing is, "....the study of the Earth utilizing electro-magnetic radiation (EMR) which is either reflected or emitted from the land surface in wavelengths ranging from ultra-violet (0.3 micrometre) to microwave (3 metre)."1 Selected examples which illustrate a variety of successful geologic applications include lithologic mapping, 2 engineering soils mapping,3 tectonic interpretation,4 and mineral and petroleum exploration.5 This report examines the applicability of remote sensing for bauxite exploration in northeastern Mississippi. Specific objectives were to map lithologies of northeastern Mississippi from LANDSAT imagery, to determine the utility of LANDSAT imagery for delineating and mapping known deposits of bauxite, and to discover and map new bauxite deposits.

Jan 1, 1977

By Thomas F. Pedersen, J. Jay McNee, Alan J. Martin

Field sampling was conducted in Lake Junin, Peru in order to assess the post-depositional reactivity of the highly contaminated lake sediments. High resolution profiles of dissolved Fe, Mn, SO42- and H2S across the sediment-water interface illustrate that the organic-rich sediments in the main basin become anoxic within several millimetres of the sediment-water interface. These permanently submerged deposits in the main basin serve as a diffusive sink for dissolved Zn and Cu. Conversely, the periodically unsaturated deposits in shallow areas are characterized by the remobilization of Zn and Cu in the deep acidic (pH < 4) pore waters, resulting in the release of these metals to the overlying water column.

Jan 1, 2000

By Jan K. Wolski

Detection of the air recirculation branches within a large ventilation network may be difficult, therefore a PC computer routine has been developed to perform this task in an efficient and reliable manner. This paper describes the method illustrated using a network with complex multi-recirculation circuits. The fact that only the air flow directions and not the flow rates are used in calculations is of some interest. The air recirculation during a real mine fire is demonstrated using the PCVENT program, whose version 4.0 includes current information about any recirculation branches during network calculations or during a fire simulation. This paper also discusses some transient problems related to air recirculation, and gives examples.

Jan 1, 1993