Search Documents

By R. W. Bartlett

Aeration curing, over- a long duration in wet- red stockpiles, shows promise as an affordable pretreatment method for oxidizing gold encapsulating sulfide minerals, and possibly organic matter, in low grade refractory ores. Following aeration pretreatment, the ore is reclaimed, neutralized, and cyanide leached by conventional practices. Large tonnages of subeconomic material, including mine stripping waste, may he converted into ore by this new technology. The results presented show that a successful application of this technology will likely require crushing to about -2 cm (-3/4 in.), followed by aeration in a wet stockpile for long periods, up m three years. Natural convection may he inadequate, hut forced air ventilation, at modest pressures and power consumption, is affordable.

Jan 1, 1991

By K. A. Brame, L. G. Austin, R. S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-ordering grinding studies in a laboratory ball mill according to the Austin, Klimpel, and Luckie procedures. The results were scaled to five larger mills of 0.56, 0.82, 8.36, 4.41, and 5 m in diameter assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distributions and capacities for batch grinding in the smaller mills and open-circuit grinding in the larger mills. The predicted capacities were in approximate agreement with experimental values except for the 5-m diam mill. The Bond method gave capacity predictions that were 4570 to 150% too high.

Jan 1, 1987

By V. W. Skema, M. W. Smith

Pennsylvania has 4,000 km (2,500 miles) of streams that do not meet water-quality standards due to acid mine drainage (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. To abate AMD, Pennsylvania is using a watershed-based approach that includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Water-shed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves that could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 2002

By Y. Lv, H. Ye, D. Du

Electrolytic manganese residue (EMR) is a kind of industrial solid waste with high silicon content that contains harmful metal elements such as chromium (Cr), copper (Cu), lead (Pb), cadmium (Cd), nickel (Ni) and cobalt (Co). Developing a highly effective and environmentally friendly process to treat EMR is important, both for the reutilization of metal resources and for environmental sustainability. In this study, the bioleaching of available silicon from EMR using silicate bacteria is investigated, with flask experiments conducted to optimize the parameters in the bioleaching system. For metal ions, the concentrations of manganese (Mn), Co, Ni and Pb in solution were measured to determine the environmental safety effects before and after bioleaching. The results show that the bioleaching rates of available silicon in the slag were mainly affected by the temperature, pH and pulp density. Under the optimal conditions of temperature of 30 °C, pH of 7.0, pulp density of 5 percent, shake flask rotational speed of approximately 210 rpm, particle size of approximately 0.150 mm and leaching time of 16 d, the concentrations of available silicon in the bioleaching system rose to approximately 110 to 140 mg/L. The metals remaining in the residues were mainly bonded in stable fractions, with concentrations lower in the leachate after bioleaching. This study demonstrates that silicate bacteria can be used to increase the contents of available silicon from EMR, and that bioleaching technology can realize the harmless resource utilization of EMR.

By G. C. Adams, J. H. Fowler

Canada's gypsum industry began more than 200 years ago in the Maritime provinces when farmers attempted to supplement their incomes by selling "land plaster" to traders bound for the United States. Rising from such humble beginnings, gypsum now contributes significantly to the economies of nine of Canada's 10 provinces. Thirteen open-pit and three underground mines produced a total of 8.4 Mt (9.3 million st) of crude gypsum, and 17 processing plants manufactured 2.5 Mt (2.8 million st) of finished products in 1985. Recent economic growth in North America has resulted in steady increases in gypsum production. However, competition from foreign producers and by-product gypsum pose a growing threat to Canada's gypsum mining industry.

Jan 1, 1987

By Raphael Mourad, Colin R. Phillips

Investigation of the traps in LiF:Mg, a multi-peak phosphor, was carried out using simple phosphorescence decay analysis. Half lives at room temperature of the trapping centres (peaks -lb, -la, -1, 0, 1, 2, 3a and 3) in the phosphor after irradiation with [a] radiation were found to be 3 s, 5 s, 28 s, 4 min, 15 min, 1 h, 6 h and 2 d respectively. Justification for the method of analysis is pro- vided and the results of measurements compared with published data. The effects of pre-annealing at 400°C for 1 h and 80°C for 24 h on the trapping configuration and on the trapping efficiencies were also studied.

Jan 1, 1981

By H. Y. Sohn, M. Pérez-Tello, J. Löttiger

An investigation of the oxidation reactions of two industrial copper mattes was performed using dflerential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) at heating rates of 20°C and 8°C/min, respectively. The temperature of incipient reaction, the total exothermic and endothermic heats of reaction and the weight change during the oxidation process were measured as functions of the oxygen concentration in the oxidizing gas, matte grade and matte particle size. The temperatures of incipient reaction measured from the DSC experiments were found to increase monotonically with all three input variables. TGA experiments showed that Cu2O and CuO CuSO4 are formed before the complete oxidation of Cu2S to CuO.

Jan 1, 2000

By J. L. Post

A near-surface body of readily available Na-montmorillonite is located about 24 km (15 miles) southeast of Fallon, NV. The clay, which forms an irregular deposit about 4.8 km (3 miles) long, lies in altered rhyolite within a fault zone. The clay is similar to Wyoming bentonite but is less uniform in composition and contains less MgO and more Fe2O3 in its crystal structure. The clay interlayer cation population can be estimated by using a modified DTA procedure. With selective mining, the industrial properties of the Nevada clay are adequate for use as drilling mud, in foundry applications and as a sealant for hazardous wastes and canals.

Jan 1, 1997

By V. Canby

Introduction Located in Russia’s Chukotka Autonomous Region near the Arctic circle and 425km from the seasonal port of Pevek (population approximately 4600), Peschanka (or ‘Anyui’) is perhaps the world’s most isolated CuMoAu porphyry deposit of significant grade and tonnage. In addition to its extreme remoteness (66°36'N/164°30'E) and lack of developed infrastructure, Peschanka is located in one of the world’s coldest regions, with annual average temperatures well below freezing. Soviet exploration up to 1985 defined four zones with inferred resources of roughly 940Mt @ 0.51% Cu, 0.42 g/t Au, 1.4 g/t Ag and 0.019% Mo (1).

Jan 1, 2007

By Rilung Xu, Jerry C. Tien, Jian Liu

As underground mines become deeper and ventilation networs more complex, ventilation data becomes more complicated and voluminous, making timely ventilation planning and necessary changes more difficult. Oftentimes, ventilation engineers have to rely on special techques using graphs and schematic maps to carry out necessary ventilation planning [1, 4, 5, 6, 9, 10, 11, 12]. A different graphical method, similar to that reported by Taminago and Isobe [10], has been developed in China [13]. This method uses a two-dimensional diagram drawn from available ventilation survey results. It combines both the customary pressure-quantity diagram and ventilation schematic map, and can greatly expedite the interpretation of survey results, facilitate ventilation system design, short and long-range planning, and emergency planning.

Jan 1, 1993

By E. B. Johnson, G. Kjerbol, L. J. Holloway

The Mount Baker Ridge Tunnel is a major improvement of Interstate Route 90 in the State of Washington. The total length of planned underground construction is about 3,400 feet (1,040 m) of which 1,332 feet (406 m) will be constructed by a stacked-drift tunneling method. Sized for vehicular traffic on two levels, the net interior diameter will be 63 feet (19.2 m) requiring an exterior diameter of about 80 feet (24.4 m). The material to be excavated is predominantly stiff clay, and this will be the largest-diameter tunnel ever attempted in soft ground. A construction contract for the stacked-drift tunnel was awarded in late 1982.

Jan 1, 1983

By Dirk van Zyl

Three conditions are required for a risk to be realized: (1) a source of risk (i.e., hazard) must exists (2) some process must take place which will lead to the exposure of people, animals, and/or the environment to the hazard: and (3) as a result of the expense, undesirable effects are produced on the people, animals, and/or the environment. A comprehensive risk assessment addresses all three of the conditions through the following four steps: (1) risk source (hazard) characterization, (2) exposure assessment, (3) dose-response assessment, and (4) risk estimation. Although the terminology may differ, the overall approach of financial, public health, and environmental risk assessments is the same (National Science Foundation, 1985).

Jan 1, 1988

By Jorgensen D. K.

The Bullfrog and Montgomery-Shoshone deposits, outside Beatty, Nevada, have a combined drill-indicated reserve of 17.4 M tons of ore with an average grade of 0.103 oz/t Au and 0.240 oz/t Ag. The deposits occur in Miocene volcanic rocks which underwent large-scale movement within a detachment-faulted terrane. The principal host to gold mineralization is a strongly welded rhyolitic tuff which experienced brittle deformation during plate movement. Open-space fractures and breccia were filled with quartz, calcite, and adularia accompanied by lesser pyrite, gold, and acanthite. Gold occurs as micron-sized particles within and adjacent to the low-angle fault and along associated listric-normal and tear faults.

Jan 1, 1989

By George L. Wilhelm

Many factors, some of which are not easily defined or described, must be considered in the design of a hydraulic backfill system. After participating in the design of several plants, I have a conviction that future refinements in sandfill systems must come in large part, from the merging of good design ideas and information from existing operating plants. It is important then, that we document and publish information on existing plant designs and their operating characteristics. This information will then be available for use by our successors and later innovators in hydraulic fill placement. The Mayflower hydraulic sandfill system is similar to other plants. The intent of this paper is to describe only this system's unique design and operating characteristics. I will not describe in any detail, the familiar elements of the system. I will document some of the observed hydraulic characteristics of the system, elaborate on some of the design situations that had to be solved, and will discuss operating factors that are not generally described in our technical literature.

Jan 1, 1968

By Edward C. Spalding

The mineral estate of Arizona's State Trust lands, which are administered by the State Land Department for the benefit of the common schools and 14 other beneficiaries, totals more than 10.5 million acres, or almost 15 percent of the State's entire area. Trust lands exist in all 15 of the State's counties, with the most and least acreage found in Yavapai and Gila Counties, respectively. Revenues derived from the Trust mineral estate include royalties, rentals, and fees. In Fiscal Year 1983-84, these revenues amounted to $4.2 million, or 13.5 percent of all income received by the Trust during this period. Industrial minerals, led by sand and gravel, contributed $1.1 million from 82 active properties.

Jan 1, 1987

By Gabriel E. Zárate, Juan C. Guzmán

In Chile there are significant amounts of gold in flotation tailings that could be recovered, being heap leaching the most promising alternative. In order to determine the feasibility of treating these tailings by this method, a detailed study is carried out using 4 representative samples. After defining the best conditions an economic evaluation is done for a plant treating 200 tpd, sensibilizing with respect to parameters such us gold price, tailing grade and capital costs. The results show that it is technically feasible treat these gold tailings by heap leaching with gold extractions over 70 %. It is also economically feasible for gold grades higher than 0.5 g/t and gold prices over 350 US/oz.

Jan 1, 1987

By P. F. R. Altounyan, I. W. Farmer

Groundwater freezing was used to stabilise 8m thick beds of saturated and weakly cemented sands at a depth of 170m, during driving of twin 1 in 4,5.2m o.d. circular drifts from the surface to the Coal Measures through 600m of Permo-Triassic strata. Instrumentation was installed during erection of the lining in frozen and unfrozen ground to measure ground and groundwater pressures on the lining and ground temperatures up to lm into the frozen ground. Observations showed that following thawing, effective lining stresses in the frozen zone were low, indicating minimum strata disturbance during freezing and subsequent machine excavation. Groundwater pressures were lower than expected.

Jan 1, 1981

By Russell G. Slayback

An integral part of site investigations for shafts and underground workings should be hydrogeologic evaluations of the need for and method of ground-water control. Such investigations should include: 1. Classification of the problem by aquifer type. 2. Integration of other site investigations with hydrogeologic programs, including assessment of the need for water control. 3. Planning and conduct of aquifer tests tailored to the aquifer situation. 4. Evaluation of pumping requirements to achieve water control objectives. 5. Scheduling of dewatering for optimum results and costs. 6. Evaluation of environmental impacts of pumpage and water discharge. 7. Planning of operational monitoring for program modification and liability limitation. Early hydrogeologic involvement can result in avoiding unnecessary duplication in site investigations.

Jan 1, 1981

By R. E. Johnson, M. Schipper-Zablotskaja, B. R. Palmer, van Sandwijk A.

A procedure has been developed for the removal of zinc from acid solutions containing aluminum, silicon, calcium, magnesium, sodium, potassium and manganese ions and high concentrations of chloride ions. The first step of the procedure involves the precipitation of aluminum and silicon at pH 4.2. The second step, the removal of the zinc as zinc oxide, was studied in detail to get in- sight into the formation of oxychlorides. A diagram was developed giving the conditions at 75O C under which the formation of oxychlorides is avoided. Under optimal conditions a zinc oxide with less than 0.5 weight percent of chloride can be produced from 11 - 16 g/l chloride solutions.

Jan 1, 1993

By Richard E. Steffens

The underground portion of Duke Power Company's Bad Creek Pumped Storage Project in northwestern South Carolina consists of a powerhouse cavern (132 m. long, 23 m. wide, 50 m. high), 407 meters of shafts and approximately 3615 meters of tunnel, both lined and unlined, with diameters varying from 4.2 meters to 9.0 meters. A case history is presented, including the early pilot tunnel exploratory work and how this affected design, the design of the project, and the excavation, rock support and tunnel lining work. Problems and experiences encountered during the construction are given. The effects of high horizontal insitu stresses in the granitic gneiss are discussed along with solution taken.

Jan 1, 1989