Search Documents

By V. R. Degner

The trend in both the metallic and non-metallic mining industry is toward processing increasing y higher tonnages of lower grade ores, thereby resulting in a growing interest in progressively larger volume individual machines in the flotation circuit. Because of the relatively high cost of large flotation machine development and evaluation, it is important to establish a rational basis by which the existing smaller flotation machine experience can be extrapolated to establish the configuration of the next larger family of flotation machines with a minimum of development modification in the field. This paper reviews the R&D approach used in translating smaller flotation machine experience to establish the configuration of a 1000 cu ft (2B.3 cu m) induced air machine. Internal cell hydrodynamic principles, which governed this extrapolation, and cell (liquid) surface and froth management considerations will be reviewed, and prototype machine mill tests will be summarized.

Jan 1, 1978

By E. R. DeMen

In late 1965 General Mills announced the availability of a new liquid ion exchange reagent, LIX®-64, for the recovery of copper from various solutions, such as dump leach liquors. Acceptance of this material by the copper industry has been gratifying. A number of pilot plants have been operated, and at this writing there are four commercial plants either in operation or under construction. The properties and operating characteristics of this reagent have been described in previous papers.1,2 LIX-64 is quite effective and selective for copper extractions although partially limited in pH ranges, losing extraction efficiency as the acidity of the feed solution increases to below pH 1.0. Also, the LIX-64 content in the kerosine carrier was limited to about 10 volume percent (except for special cases) because of rapidly decreasing phase disengagement rates above this content. This in turn led to large plant capital costs, as the organic flow rates had to be in- creased (rather than LIX-64 content) to extract the copper from high content liquors. This was true in all circuits where the feed copper content ran above 2.0 g/l copper. A reagent was needed which would extract copper from more acidic liquors (or higher copper content liquors) and which exhibited improved phase disengagement characteristics with reagent contents up to 30 volume percent. General Mills is pleased to announce the availability in commercial quantities of a new and improved reagent, L+-64~. This reagent broadens the pH range in which copper can be extracted, and exhibits superior phase disengagement characteristics. The improvement in the reagent has been noted in laboratory circuits, as well as pilot plant runs and commercial operations.

Jan 1, 1970

By Norman M. Junk

Following the wide-spread acceptance of ANFO as a useful, low cost blasting agent, studies have been made to adequately describe the physical and explosive properties of this material (1). As the quality of the AN blasting prill improved, reliability and sensitivity to initiation were greatly increased and many methods of priming were chosen from the standpoint of economics with little appreciation for the need to initiate so as to obtain the most efficient detonation. Under certain conditions, ANFO could be initiated with primers no more powerful than a No. 8 blasting cap (2). Research on primers for ANFO followed and it was demonstrated that this blasting agent was subject to extreme transient velocities upon initiation with wide variations in energy output depending upon the nature of the primer. For these reasons it was shown that powerful priming was economically justified (3). These studies helped to define the properties of an effective primer and the guides for its efficient use. In the vast surface coal mining industry, technological advances in earth moving equipment were paralleled by the development of larger and larger borehole drills (4). Even though ANM) was the major blasting agent used in this industry, investigations of priming techniques in these larger boreholes was almost non-existant. In 1962, Mr. Cleon Woolsey of Enos Coal Company disclosed to the industry that dramatic improvements in blasting production could be achieved with new priming and boostering methods (5). The research program at the Atlas laboratories was designed to explain these results and extend the study of initiation of ANFO with both high explosives and slurry explosives and to define the principles involved.

Jan 1, 1968

By V. K. Gupta

The phenomenon of zero order production of fines associated with the batch comminution of monosize feeds in tumbling mills has been examined in the context of the size discretized population balance model. It has been shown that the model admits zero order production kinetics only in an approximate sense. The necessary and sufficient conditions for approximate zero order production of fines have been obtained. As these conditions cannot be expressed in terms of the model parameters Sj and Bi,j alone,. several examples have been used to illustrate some of the important characteristics of the zero order production systems. One of the important characteristics of these systems has been identified as a "weak necessary condition", and the other as a " favourable condition ".

Jan 1, 1985

By Walter R. Hibbard

Precipitation in the northeastern United States, Florida, California and in many industrialized areas of the world is now more acidic (lower pH) than can be accounted for by natural causes. At the same time, the acidity of many lakes and streams in the northeastern United States has been measured and found to be similar to that of actual rain. These facts have led to conclusions that the two conditions are related. Coal burning utilities, 700 to 1000 miles upwind, have been accused of being the cause, leading to proposals for strict emission controls on the alleged offenders. The costs of these controls would place an estimated $10 to $15 billion capital burden on utility customers in about 15 states plus $2 to $6 billion annual operating costs. There appears to be no direct well-established scientific evidence that the accused are guilty but that the indictment is based largely on circumstantia1 evidence. This study examines the evidence, describes the situation and proposes what must be done to reduce the acid precipitation in an orderly cost beneficial manner. It is interesting to observe that studies by the different adversaries on the acid precipitation issue come to different conclusions largely because they do not read the same literature, but selectively develop evidence to support their own points of view, This study will try to review the issues impartially and reach a position of scholarly balance.

Jan 1, 1982

By G. Hwang, S. Park, H. Kim, J. Choi, P. Seo

"In the mineral processing, clay minerals have negative effects on the flotation of valuable minerals. In this study, we investigated how the floatability of malachite (CuCO3·Cu(OH)2) is affected by presence of the clay minerals in the fundamental aspects. Flotation experiments were conducted by using Na2S and PAX (potassium amyl xanthate), and the floatability of malachite was compared between the cases in the presence and absence of clay minerals. The results showed that floatability was greater in the absence of clay minerals than in the presence of clay minerals and decreased with increasing weight percent of kaolinite under same conditions applied. In addition to examine how clay minerals affect malachite floatability, we conducted flotation experiment with changing clay adding order. The results indeed showed that malachite floatability was affected by clay adding sequence. INTRODUCTION The demand of copper is growing as industrial development increases, but mineral resources are limited. Therefore, studies for Cu oxide flotation are being conducted to improve their recovery(1-3). However the mining industry is well aware of the difficulty in treating copper ores in the presence of clay minerals(4). Clay minerals have unique properties and these properties may affect flotation. In the previous studies, the effect of slime coating of clay minerals on flotation was investigated(4-6). For example, Zhao and Peng (2014), Peng and Zhao (2015), and Arnold and Aplan (1986) found that clay slime coating on chalcopyrite, chalcocite and coal surfaces through the electrostatic attraction reduced surface hydrophobicity and then depressed the flotation. Other researchers have also reported clay minerals have impact on pulp rheology. Especially in the case of bentonite, pulp viscosity increased with increasing amount of bentonite and the higher pulp viscosity have deleterious effect on copper recovery(7, 8). However, these studies only focus on slime coatings and pulp rheological behavior. Forbes et al. attempted to decoupling rheology and slime coatings effect on flotation but this study has limitation that individual role of two clay species either attached to mineral or suspended in bulk solution was excluded(9). Hence, in this study, we aimed to investigating the effects of individual clay (suspended and attached) on malachite flotation."

Jan 1, 2016

"Outotec’s TankCell® e500 flotation cell was commissioned during 2014 at the Kevitsa Mine in northern Finland. The TankCell® e500 is the first cell in this size class (500m3) to be run in an operational duty and it has been working as the first rougher in the copper flotation circuit. Treating around 850tph with an average grade of 0.3% Cu the TankCell® e500 has run with an average copper recovery of 71% and an average enrichment ratio of 50. In addition the cell has proved to be very energy efficient, operating with a specific energy of around 0.4kW/m3 under production conditions. This presentation will provide a review of the installation and operation of the TankCell® e500 at Kevitsa and will summarize the results found in the published literature from the various testing campaigns conducted around the cell. INTRODUCTION The TankCell e500 was installed and commissioned at the Kevitsa mine in northern Finland in 2014. Post startup the cell was initially run for testing and optimization with various test campaigns undertaken. but was subsequently taken into a production duty (Mattson et al., 2015a). At Kevitsa the cell is run as the first copper rougher replacing the previous two copper roughers (both 160m3) in this duty. The unit is running at between 38-40% solids at a feed rate of approximately 850tph. Since operational the average copper recovery from this single cell has been around 71% copper. This is typically with an enrichment ratio of around 50 being fed with an average head grade of 0.3% copper. More details on the circuit configuration and production performance of the e500 at Kevitsa can be found in Mattson et al., (2015a) and Murphy et al., (2016). In addition through the optimization program with the use of a variable speed drive controlling rotor speed it was found the the e500 was very energy efficient under production conditions. During this work the cell was found to run at a specific energy of around 0.4kW/m3 which exceeded design expectations (Xia et al., 2015)."

Jan 1, 2016

By Charles U. Keranen

The Tilden Mine is an iron ore mining, processing and pelletizing facility located on the Marquette Iron Range in Michigan's Upper Peninsula. It has a designed capacity to produce 8 million long tons of pellets annually from 21 million long tons of crude. It is a partnership owned by The Cleveland-Cliffs Iron Company, Algoma Steel Corporation, LTV Steel Corporation, the Steel Company of Canada, Wheeling Pitts- burgh Steel Corporation and the Sharon Steel Corporation. Cleveland- Cliffs manages and operates the Tilden. The crude ore averages 35% iron and is primarily non-magnetic iron oxide and silica. The major ore mineral is martite. Hematite, earthy hematite, goethite and magnetite are also present. The principal gangue mineral is chert. The ore grains are mostly in the 10 to 25 micron size range which necessitates very fine grinding for liberation. The concentrating process is the most complex one used in the iron ore industry. The unique technology for Tilden was developed in the mid and late 60's. The design and construction occurred in the early 70's and operation of the first phase which was of 4 MLTPY capacity began in October. 1974. Expansion of the facility to the current 8 MLTPY capacity was completed in 1979. Chemicals are the key to the beneficiation process at the Tilden Mine. The flowsheet utilizes selective flocculation - desliming, cationic silica flotation and concentrate dewatering by thickening and filtering. Nine different process chemcals are used. The control of the reagent feed systems is highly auto- mated. The entire concentrator is operated from a central control room. The concentrator flow diagram is presented in figure 1. The plant consists of 12 primary autogenous grinding lines, a common crushing circuit to handle an intermediate product within the primary grinding section, 24 pebble mill lines with cyclones and deslime thickeners, 12 flotation lines, 4 concentrate thickeners and slurry tanks, 8 lines of filters with six machines per line, and 2 tailings thickeners. A pumping system was installed in 1980 to permit the direct return of tailings thickener overflow water back to the reuse water pumphouse.

Jan 1, 1986

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By Paul H. Johnson

Resource Engineering and Development, Inc. is designing and building a portable 150 to 225 TPD, flotation-cyanide leach plant with unitized, skid-mounted components. This plant design, with its portability, low capital investment, and high recovery of silver and gold from many partially oxidized ores, is well suited to treat many small, high-grade deposits, old waste dumps, and old mill tailing piles. A description is given of flotation and/or cyanide leach tests run on about 17 partially oxidized, newly mined ores; waste dump materials; placer slimes; and old mill tailings.

Jan 1, 1981

By Donald R. Williamson

Statistical studies at Cyprus Pima Mine indicate that samples from 22 blastholes are necessary for determining average copper grades, within a desired range of precision, for mine-model blocks by arithmetic averaging. The average number of holes in such blocks is 14. Many considerations show that more holes will not be drilled for sampling. A way to determine block grades more reliably than by" arithmetic averaging was sought. Thus far arithmetic averaging has proven to be the best procedure for the particular operation characteristics despite the small number of samples. It naturally follows that expenditure of great effort in sampling blasthole cuttings is unwise.

Jan 1, 1977

By Werner A. Ruemmele

Eisenhower Memorial Tunnel, called Straight Creek Tunnel during construction is located 60 miles west of Denver, Colorado at 11, 160 ft. elevation. It is 8, 510 feet long, and carries two lanes of 1-70 traffic under the Continental Divide. This paper describes improvements and changes made in construction methods for utilities, concrete lining, ceiling, wall covering and paving to allow maximum offsite fabrication and activity overlap resulting in a one-year faster completion for traffic. The substantial changes proposed on a design-and-construct basis by the contractor and put into effect after State approval were: 1. Substitution of ductile iron and thick-wall P.V. C. pipes for clay pipes allowing placement and operation before hole-thru. 2. Outside pre-assembly of large rebar mats, using a novel tension-splice with cable clamps. 3. Arch concrete placement method modified to make 4, 322 ft. of lining in 10 weeks possible. 4. Safety barriers precast and epoxy coated offsite instead of cast-in-place and tile faced. 5. Prestressed hollow ceiling slabs with porcelainenamel coated steel sheets assembled offsite, instead of in-place glazed tile and in-place cast concrete ceiling. 6. Glazed tile wall panels 8 ft. long by 11 ft. high assembled off site and erected using vacuum pad mounted on special lift. 7. Asphalt paving while other work proceeded, instead of reinforced concrete slab and asphalt overlay. Work started in January 1968, but advance came to a one-year standstill for major structural redesign and negotiations of a new agreement during 1970. Using multiple drift construction followed by top-heading and bench excavation, it then progressed to hole-thru in July 1972. As a result of art 18-month overlap of activities the tunnel was opened for traffic only eight months later in March 1973. Gibbons and Reed Company of Salt Lake City, Utah sponsored the joint Venture of Al Johnson-Gibbons and Reed-Western Paving-Kemper during 1971, 1972, and 1973. The tunnel was the subject of a previous paper delivered at the RETC '72 in Chicago by R. C. Hopper, T. A. Lang, and A. A. Mathews, describing geology, unusually severe structural loading and multiple-drift tunnel excavation.

Jan 1, 1974

By G. C. Tipper, A. P. Deane, A. G. Myers

SCHEME DESIGN London’s Heathrow Airport, as the world’s busiest international airport, is missing one vital aspect - a dedicated rail link which connects directly to the city. All this is about to change with the construction of Heathrow Express - a fast, high quality rail service between the airport and the centre of London. It was recognised in the mid 1980s that if Heathrow was to accommodate the forecast growth in passenger numbers and the resulting increase in road traffic, a dedicated airport rail service would be vital. The main access into the centre of Heathrow is via a road tunnel with a direct link to the M4 motorway. The airport has introduced a number of traffic management schemes, but these can only achieve so much benefit. Growth in air passenger traffic is predicted to continue at an average of 4% per annum well into the next century and it was clear that significant investment was needed. Heathrow Express at a cost of over £350 million will provide this when it starts its service in June 1998. The business case for the scheme is based on a rider ship of around 15% of air passenger traffic. The initial Heathrow Express service will be based on four trains per hour, up to 8 car train lengths, providing a high speed non-stop service between the airport and central London in just 16 minutes. Initially a joint venture between the British Railways Board and Heathrow Airport, by mutual consent of the two parties, Heathrow Airport recently purchased the British Railways Board share making this one of the largest private sector rail projects currently under construction in the UK. Leaving Paddington, the main rail terminus in West London, Heathrow Express trains will travel 12 miles on the newly electrified line to airport junction, north of the airport. At this point they will leave the mainline to enter a 5 mile tunnel section that runs underneath the heart of the airport. The railway companies are responsible for track work, signalling and electrification of the 12 mile main line section including a grade separated junction over the main tracks for the Great Western Railway which links London and South Wales. Heathrow Airport is re-

Jan 1, 1997

By Pan Eimon

She was young, beautiful, intelligent, virgin. Her name was Barbara and she captured the attention of many men, especially those in dangerous occupations. Her rich and doting father was hopeful of making an advantageous marriage for his daughter. Instead, she defied him, became a Christian, and refused to marry. Traumatized, he killed her and was himself struck dead by lightning. That is not the plot of a new soap opera. It is the melodramatic story of a Turkish teenager who was martyred in the third century but lives still as patron saint of mining. The story begins with a 20th century fact. Santa Barbara is a figment of imagination - perhaps based on an early oriental folk heroine, embroidered by a seventh century storyteller, and reworked by a ninth century Greek martyrologist. The authoritative Lives of the Saints reports: "There is ... Considerable doubt about the existence of a virgin martyr called Barbara and it is quite certain that her legend is spurious. There is no mention of her in the earlier martyrologies, her legend is not older than the seventh century, and her cult did not spread until the ninth." The Catholic Dictionary adds that the Barbara story is probably "a pious legend." Widely revered Santa Barbara was one of the most widely venerated saints of the Middle Ages. She became the patron, not only to miners, but also to artillerymen, engineers, architects, builders, stonemasons, gravediggers, and sailors. Mines, mountains, churches, and places bear her name. Barbara's feast day, Dec. 4, appears on the most ancient holy day calendars. And a Barbara festival is still celebrated throughout central Europe, in Spain, and in mining areas of Latin America on that date. The Pacific coast channel, the city, and the mission of California are named for Santa Barbara. An expedition, sailing that coast under Viscaino in 1602, was saved from shipwreck on Dec. 4 after the sailors prayed for Barbara's intervention. Franciscans gave her name to the modern Franciscan Province of Santa Barbara, which embraces six western states and the Philippine Islands. Barbara is intimately entwined with mining. The origins of both saint and profession are lost in an-

Jan 11, 1985

By F. X. Ferney

The centrifuge which will be reviewed in this dis¬cussion is the continuous solid bowl typo. As there are presently approximately 2000 of these units operating in our country, and about 200 of these in use in the coal industry, I expect that most of you are acquainted with its operating principle. How¬ever, for those who are not familiar with the machine a brief introduction is in order. The continuous solid bowl centrifuge was first successfully marketed, worldwide by the Bird machine Company in 1934. The successful development of this unit was based primarily on the invention of a drive mechanism to properly control the differential speed between the two rotating elements. This centrifuge was introduced into the coal industry immediately following the second World War. Today there are five or six additional firms' selling this machine in our country, and approximately twenty others in Europe, England and Japan.

Jan 1, 1965

By E. R. Bauer

A primary goal of Ground Control Research, Bureau of Mines, U.S. Department of the Interior, is to develop information that can be used by the mining industry to reduce accidents and fatalities due to failure of mine roof. A specific research objective is to determine methods to detect hazardous coal mine roof. This paper reviews the existing and experimental techniques, and describes a recent Bureau of Mines contract research project that resulted in a simple technique and prototype instrument for evaluating mine roof competence.

Jan 1, 1986

By Peter I. Brooker

The turning bands method for the simulation of spatially correlated data in two or three dimensions requires that the relation- ship between the covariance obeyed by the realizations first generated on lines, and the covariance of the two or three dimensional process must be solved. In three dimensions the solution is immediate, but in two dimensions the integral equation relating the covariances of the one and two dimensional processes is more complex. This is solved in this paper and is applied to the most common model used in ore deposit description, the spherical covariance.

Jan 1, 1984

By W. A. Vine

Next year, in 1964, Butte will celebrate its Centennial. It was in May, 1864, that the first recorded mining activity took place. During that summer, several rich placers were found on Silver Bow Creek and its tributaries, and a gold rush followed. As placer mining proceeded in the creek beds, the quartz lodes on the hillsides were located and the veins were prospected. Mining in Butte entered its second phase when the rich silver mines, the Alice, Moulton, and Lexington, were opened. The silver boom lasted until the decline in the price of silver in the early 1890's forced the closure of many of the mines. An indication of the beginning of the copper mining era in Butte was in 1866 when it was noticed that green copper carbonate discolored some of the, lode material. It was not until ten years later, however, that the Anaconda and St. Lawrence claims were located by Michael and Ed Hickey. The claims were sold in 1880 to Marcus Daly and in 1881, Daly obtained financing and organized the Anaconda Silver Mining Company to exploit the vein The silver venture was a failure because of the predominance of copper which diluted the bullion to only 400 fine.

Jan 1, 1963

By Judson C. Higgins

The paper addresses changes in surface transportation methods in the Industrial Minerals business starting with history, the changes to present time including such areas as energy costs, improved highways, changes in regulations and deregulation, and attempts to project future transportation trends. Transportation methods such as rail, piggyback, truck and barge are compared, and their impact on Industrial Minerals producer's costs and profits examined. The customer impact on our businesses due to deregulation is also discussed.

Jan 1, 1983

By W. E. Adkins

Ore and waste haulage usually constitute one of the major cost items in the operation of an open pit mine. This has always been true at the Chino mine, one of Kennecott Copper Corporation's western mines, located in southwestern New Mexico. The Chino Mines Division is an integrated operation. The open pit mine, dump leaching operation, and a precipitating plant are located at Santa Rita, New Mexico, and a power plant, mill, smelter, and fire refinery are located in Hurley, New Mexico, about nine miles south of the mine. Approximately 22,000 tons of ore are mined and processed each day; in addition, approximately 42,000 tons of waste are removed from the pit. Originally the pit was located along the side of Santa Rita Creek but it has deepened and expanded so that at the present time, it could better be described as a nearly circular pit about one to 1.5 miles in diameter. The bottom is at an elevation of 5750 feet, the west rim near the ore gathering yard is at an elevation of 6230 feet, and the highest bench on the east side of the pit is at an elevation of 6750 feet, giving a vertical mining depth of 1000 feet. The train waste dumps reach a maximum elevation of 6580 feet. At the present time, Chino uses electric locomotives, off-the- highway trucks, and a skip system for mine haulage.

Jan 1, 1963