Search Documents

By L. Piga, G. Belardi, V. Alesse, N. Shehu, J. Freund

The physico-chemical interactions among minerals such as olivine, chromite and serpentine; the most commonly present ions in solution such as Ca and Mg; and flotation reagents such as EDTA and oleic acid were investigated. The study was conducted via release tests, electrophoretic measurements and microflotation of selected minerals coming from the Kukes deposit in Albania. The results were confirmed in beneficiation tests on two ores, one from the Kukes (Kalimash) deposit and the other from the Rizo deposit in Greece. It was demonstrated that, when Na-oleate is used as collector, chromite, olivine and serpentine can be separated at pH 2.5 and/or pH 5.5 when employing ethylenediamine tetraacetate (EDTA) on previously deslimed material. This approach ensures flotation concentrates with a Cr203 content better than 50% with a recovery of more than 75%.

Jan 1, 1998

By Parris A. Lyew-Ayee

This paper is the first preliminary report on the bauxites and terra rossas of the Caribbean. It concentrates on the islands of the Greater Antilles, and for reference purposes the Yucatan Penin- sula is included. At this point, observations made in Jamaica, Haiti, and the Dominican Republic are compared with reported information on Puerto Rico, the Bahamas, Cuba, the Cayman Islands, and the Yucatan Peninsula with regard to occurrence, as well as physical, chemical, and mineralogical composition. From this, an attempt is made at classifying the types of bauxites in the Caribbean, indicating the best reserves estimates, and the process ability of these bauxites. Some suggestions are also provided to fuel the controversy over the likely source material(s) or origin of the Caribbean bauxites.

Jan 1, 1984

By Peter J. Conroy

Introduction Most subsidence monitoring to date has been surface monitoring to develop empirical relationships of the magnitude and extent of subsidence effects. Federal regulations are forcing a better understanding of subsidence. Empirical methods of subsidence prediction may not be adequate, since the empirical relationships may not be valid between or even within coal fields. A better understanding of the mechanics of subsidence is required in order to develop and verify analytical models. This paper presents some of the results of surface and underground monitoring in longwall faces of a coal mine. The seam thickness in these mines ranges from 5 feet to 6 feet at depths of 600 to 1100 feet.

Jan 1, 1982

By Jose M. Milian, Raphael F. Matson

An intensive study was started in 1968 to determine the most economical process for winning nickel and cobalt from an extensive de- posit of complex, low grade nickel-cobalt ore (1.6% Ni, 0.10% CO) designated "the Greenvale ore." In 1974 the commercial plant at Yabulu, in Queensland, Australia, began processing the ore. In the interim, a great deal of laboratory and pilot-plant effort was applied to develop technical, process and commercial design data to demonstrate to potential financial backers and customers that a full-scale plant was feasible. The laboratory test work, pilot plant facilities and pro- gram are briefly reviewed in this paper.

Jan 1, 1979

By A. S. Trimble, J. C. Hower

The petrographic composition of sized coal produced through the progressive grinding of a Central Appalachian high-volatile bituminous coal blend was analyzed for multiple sets either by removing fine, -200-mesh, coal after each test iteration or by retaining the fine coal in progressive test fractions. With prolonged grinding, coarser fractions tend to become depleted in vitrinite and vitrinite-rich microl ithotypes, leading to progressively harder-to-grind coal remaining in the oversize, +200-mesh, fractions. The latter trend is shown both by the maceral and microlithotype composition of the coal and by the increased slope and fractal dimension of size frequency distribution, implying an increase in hardness and resistance to grinding of the oversize coal.

Jan 1, 2000

By Carol A. Hill

Native sulfur occurs with barite, celestite, and bioepigenetic calcite in the Culberson, Pokorny , and Leonard Minerals deposits, Delaware basin. The sulfur in these deposits, in "castile" masses, and in deposits of the Fort S tockton district have 6 34s values between +9 and -15. Native sulfur in the caves of the Guadalupe Mountains is somewhat lighter [(634s = -15 to -25)]. Barite in the Culberson, Leonard Minerals, and Comanche Creek sulfur deposits have 63% values of +35 to +73; celestite in the Culberson and Leonard Minerals occurrences have values of +38 and +36, respectively, and 87Sr/86Sr values of 0.707808 and 0.708138, respectively. Barite associated with sulfide, deposits, Guadalupe Mountains, have [634s] values of +41 to +62. Barite at Seven aeart Gap, Apache Mountains, is somewhat less enriched in heavy sulfur [(634s = +14 to +37)].

Jan 1, 1992

By A. E. Reisenauer, R. W. Nelson, G. W. Gee

A model assessment was made to evaluate contaminant transport to ground water from clay-lined and unlined tailings pits. The input hydrologic soil characteristics were measured on materials typical of those found at the Morton Ranch uranium mill site in central Wyoming. The assessment involved combined saturated and partially saturated flow and contaminant transport models for two-dimensional cross-sections typical of the proposed Morton Ranch burial pits. Specifically obtained from the models were contaminant flow paths, the advancing contaminant flow fronts for sorbed and non-sorbed constituents, and travel times of contaminants along flow paths. Such results enable evaluation of the environmental consequences for the alternative control methods.

Jan 1, 1980

This paper discusses how the link between design software tools and recycling models can be established in order to predict the recyclability of the car during the design phase, as well as to be able to apply design for recycling on a solid technological basis. Due to the complexity of the design of the car, optimisation of recycling can only be realised based on a sound technological basis, in which the dynamic and statistically distributed parameters affecting the recycling rate are described and understood. This paper gives a brief overview of the dynamic and recycling models, which are developed for optimisation of the recycling of the car and the calculation of recycling rates of the car in the design phase in view of EU legislation. Moreover the possibilities for modelling of shredding and liberation within the recycling system are discussed. The performance of experiments on a fundamental basis in order to collect statistically correct industrial data, supported by a closing mass balance, is referred to on the basis of a large scale industrial recycling experiment. It will be shown how design for recycling and environment can be supported by the sophisticated models as developed by the authors.

Jan 1, 2005

By E. Sehner, G. Van Weert

Metal chloride pyrohydrolysis is a fifty year old technology, operating satisfactory in many plants around the world, mainly on ferrous chloride, The capabilities and costs of its two equipment options (spray roaster and fluid bed pyrohydrolysis) are well known. Why is the technology not more widely used in mineral processing, beyond the production of MgO and upgraded TiO2slag? After briefly reviewing chloride vs. sulphate process characteristics and existing plant operations, this paper will discuss pyrohydrolysis options for the mine developer using the processing of ilmenite, siliceous zinc oxides and oxidic nickel / cobalt ores as examples.

Jan 1, 2003

?Energy-related systems: wind, solar, electric are typically materials intensive. As new technologies are widely deployed, significant quantities of the elements required to manufacture them will be needed. However, many of these unfamiliar elements are not presently mined, refined or traded in large quantities, and, as a result, their availability might be constrained by many complex factors. A shortage of these ?energy-critical elements? could significantly inhibit the adoption of otherwise game-changing energy technologies. This, in turn, would limit the competitiveness of the U.S. industries and the domestic scientific enterprises and, eventually, diminish the quality of life in the US.? -Energy Critical Elements: Securing Materials for Emerging Technologies?- American Physical Society, 2011.

Jan 1, 2012

By Charles W. Daugherty, Robert Nyren

The replacement of Boston’s elevated Highway I-93 running north to south through the heart of the city with 8-lane tunneled roadways, coupled with the underground extension of Highway I-90 eastward to Logan Airport, has earned the Central Artery/Tunnel (CA/T) Project the position of the largest infrastructure project in the U.S. today. The gigantic interchange featuring numerous ramps where these two main branches of the Artery intersect required the construction of three huge jacked tunnel boxes that were pushed beneath eight active Amtrak and commuter rail tracks that had to remain undisturbed in spite of poor geology and a minimum of cover between the track beds and the tunnel crowns. Ground freezing was chosen as the method of stabilizing the soil over the tunnels, and it was extended in one area to stabilize the ground at the intersection between the tunnels and an abutting deep cut-and-cover excavation. Because many standard geotechnical instruments consist basically of open standpipes filled with water, it was a major challenge to keep them de-iced and in a condition to provide data on vertical and lateral ground movements. The efforts to do so are herein described.

Jan 1, 2003

By Randal J. Barnes

The nonlinear network optimization algorithm developed in this paper solves the following mine ventilation design problem: find the location and size of all fans and regulators which minimize the overall system power consumption while satisfying all physical, legal, and operational constraints. This work includes the formulation of the problem within the framework of mathematical optimization, the development of the computational theory, and the creation of an efficient solution methodology. The algorithm has been implemented on a microcomputer, and a small but representative example is included. The algorithm presented in this paper has four limitations. First, the optimization process is for a single point in time: the dynamic nature of a mine ventilation system in an evolving mine is not directly addressed. Second, the topology of the ventilation network is required input information. The mathematical algorithm does not optimize the size or location of the mine ventilation airways; however, the post optimality analysis techniques can be used to aid in topological decisions. Third, the problem is formulated using volumetric flow; thus, heat and moisture transfer are ignored. Fourth, the capital cost of ventilation equipment is not included in the formulation.

Jan 1, 1989

By Randal J. Barnes

In, any open pit mine the ability to make accurate production estimations for the shovel-truck system is an important asset. This is true in an operating mine wishing to estimate production under a set of system modifications (i.e. more trucks, fewer loaders, change in roads, etc.), as well as in the pre- mining planning stages of a property. Many different methods have been proposed for solving this problem; some of the methods rely heavily on "rules of thumb" while others are highly mathematical and require access to a high speed digital computer. Analysis of shovel-truck systems with the use of simulation models is a widely accepted technique within the industry. Through the use of such models it is possible to account for much of the inherent variability of the system and thus produce meaningful results. However, simulation studies are expensive. Formulation and setup of the actual simulation model requires a significant commitment of time and energy. In addition, the cost of the necessary computer runs is often of considerable magnitude.

Jan 1, 1979

By D. Hodouin

The optimisation of mineral processing plants requires the evaluation of performance indices such as production rate, product quality, valuable mineral recovery and process efficiency. Decision to change operating conditions or equipment to improve plant performances rely on the significancy of the estimated performance indices. The better is the quality of the estimation, the better is the discrimination capability of the index and as a consequence the larger is the operation improvement. The reliability of performance calculation depends on the sensors nature, accuracy and location, on the data redundancy, on the correction method applied to raw data and finally on the propagation of measurement errors along the calculation of performance indices. To maximize the quality of the data collected for performance evaluation, the following techniques are presented, discussed and illustrated: redundancy and observability analysis, data filtering for mass conservation, variance analysis of performance calculation, and data acquisition strategy design.

Jan 1, 1991

By Jakub Nalaskowski, Robert Aranowski, Jan D. Miller, Jan Hupka

The polyolefins, mainly polyethylene and polypropylene particles, are used as an active filler material in polymer-polymer blends and are being used for the modification of asphalts to pro- vide for high-load, low-maintenance road construction. The stability of prepared blends depends on the interaction forces between polyolefinfiller and the matrix and/or between two polyolefin filler surfaces in the polymeric matrix. Various additives, especially surfactants, can be used to modify these interactions and improve the stability of polymer blends. In current research, direct force measurements between polyethylene (PE) surfaces in n-tetradecane, a nonaqueous solvent imitating the polymer matrix, were performed in the presence of lauric acid and dodecylamine using the AFM colloidal probe technique. Additionally, the zeta potential of polyethylene particles in the presence of surfactants in n-tetradecane was measured. The interac- tion forces between the polyethylene surfaces can be described as a combination of electrical double layer repulsion and steric repulsion between polymer chains extending into the n-tetradecane sol- vent. The addition of surfactant to the n-tetradecane was found to increase the repulsive force between the PE surfaces. The strongest repulsion was observed for dodecylamine. Additionally, the temperature efect on the interactions in n-tetradecane was studied. It was found that steric repulsion between the PE surfaces increases with an increase in temperature.

Jan 1, 2003

By Robert M. Belesky, H. R. Hardy

A methodology to detect the presence and monitor the stability of shallow cavities is presented in this paper. The approach incorporates surface-wave seismic and acoustic emission/microseismic (AEIMS) techniques. Application of tomography to the seismic data is made to enhance the ability to locate cavities. Zonal and hit-sequence location techniques are introduced into AE/MS monitoring schemes. These source location techniques simplify the analytical procedure yet still provide sufficient information regarding the region of AE/MS activity. The concept of unique velocity data for conventional, least-squares, source location routines is discussed. A hypothetical case utilizing the algorithm is presented. The method described has been successful based on preliminary studies. Areas of current and future research are identified.

Jan 1, 1986

By C. Tsamantaki

Water-bentonite suspensions exhibit a yield stress which is defined as the minimum applied stress for flow. Considerable debate exists about the yield stress being a material property, hence different measuring methods should give similar answers, but several investigators have demonstrated that it is an engineering reality. Yield stress is normally estimated indirectly from the rheogram obtained with a viscometer following an extrapolation to zero shear rate (the dynamic yield stress), but the technique may be prone to errors because of slip flow. Direct measurements, not prone to such errors, rely on an independent assessment of the yield stress, normally carried out with the vane method (the static yield stress). In this paper results are presented and compared regarding the yield stress of 14 different water-bentonite suspensions measured using both the direct and the indirect methods. In order to obtain a wide range of yield stress values, two different types and two concentrations of bentonite at various pH were tested. Rheological data were obtained using a rotational speed viscometer and a yield stress vane measuring device. Measured vane yield stress values ranged from 5 Pa to 83 Pa. Rheological data collected with the rotating viscometer were fitted using various conventional techniques (interpolation, linear and non-linear regression analysis) as well as using a golden section yield stress search methodology based on Herschel-Bulkley model, developed in house. The vane instrument measures directly the yield stress of the suspensions and requires no further data handling. A comparison of the measured values of the yield stress with the direct and the indirect method is then made for the water-bentonite samples. Not very large differences are observed among different techniques and the variations are discussed. Similar data from literature are also analyzed and the comparison shows that differences on the various estimation methods are much larger than the differences observed in this study.

Jan 1, 2006

By P. K. Crane, S. C. Gambrell

The work reported herein compares the support characteristics of two different types of roof truss subjected to the same force in the horizontal tension member. The major differences between the two trusses are in the sequence of tensioning the horizontal and inclined members and in the design of the loading brackets. A photoelastic model was used to compare stresses at points along the roof of the mine opening and at the junction of the roof surface and the rib. The effects of simulated subsidence on stress in the roof and on tension in the horizontal member were analyzed. Results indicate that there are significant differences in the overall support characteristics of the two trusses. Conclusions are drawn relative to which type of roof truss provides the most favorable support if the horizontal members are tensioned equally.

Jan 1, 1986

By Brian S. Prosser, Ian J. Duckworth

With the trend in the coal mining industry pushing towards improved productivity and greater production, the number and size of longwall panels is increasing rapidly. The development and mining of large longwall panels causes unique problems in the provision of adequate ventilation at the working faces. Because of the transient nature of the longwall panel, and the difficult field conditions for ventilation measurements, detailed pressure and volume surveys are often not conducted around the longwall circuit. This is unforlunate because the highest resistance airway in longwall mines is typically the longwall tailgate, which frequently represents the only unregulated split in the ventilation network. This paper examines data collected from ventilation studies of longwall panels at nine mines. The variation in airway resistance, ventilating pressure and airflow is examined and compared with specific factors such as airway dimensions, ground conditions and support type used.

Jan 1, 1997

By John A. Herbst, K. Rajamani

Process improvement is probably the most widespread objective of mineral process plant operators in the late 1980's. An important part of such improvements is dynamic optimization which involves reacting to inevitable plant disturbances in such a way that productivity is maximized at every instant of time. This paper describes the way in which mathematical models can be and have been used in dynamic optimization. Both off-line and on-line model applications are described.

Jan 1, 1989