Search Documents

By Jeff Schwoebel, Arcy, D&apos Horner

The Deep Coal Seam Project is a multi- year, large-scale research and development effort between the Gas Research Institute (GRI) and Resource Enterprises, Inc. (REI). The project is being conducted at the Red Mountain Site, a multi-well test site located in the southeastern portion of the Piceance Basin near Collbran in Mesa County, Colorado. The project objective is to develop the drilling, reservoir evaluation, completion and production technology required to produce gas from a thick, deeply buried coal seam. To understand the parameters controlling gas production, project efforts are focused on the Cameo "D" coal reservoir which lies at a depth of about 1707 m (5,600 ft) at the test site. This paper overviews the drilling, testing, completion, and production techniques used on the 1, 2 and 3 Deep Seam wells and implications for resource development.

Jan 1, 1987

By Tad S. Golosinsk

Use of computers for hoist evaluation and design dates back to the early 1960's. Mine hoist production calculations, repetitive in nature, were computerized first. More elaborate modeling of hoist operations followed soon. Typical for this, early period are the models described by Touwen (1973), and by Albert and McIvor (1984). Apart from the simple hoist production calculations, the models were very complex, typically written in Fortran, and often required advanced computing facilities and expertise to run the simulation. The early models were strictly deterministic, with no consideration given to the random nature of hoisting operations. The effects of randomness of the hoisting process on hoist performance were often accounted for by introduction of the deterministic factors, most notably of an "utilization factor" related to the hoist production. The value of the latter was based on observations of actual hoist performance, and could vary in a wide range. For example Harvey (1973) reports values of the "utilization factor" to be between 0.7 and 0.92.

Jan 1, 1989

By J. M. Mutmansky

The objective of this study was to produce coal dusts for laboratory research that are similar to mine airborne dusts in chemical, mineral, and physical characteristics. In this investigation, dusts produced in laboratory comminution equipment were compared with continuous-miner-generated dust for similarity in physical characteristics. Mining-generated dust (MGD) and bulk coal samples were first collected from an underground mining operation. The bulk samples were then processed in the laboratory for size reduction in various comminution devices. These laboratory-generated dust (LGD) samples were subjected to size and microscopic analyses. Physical properties of the dust particles were studied on a scanning electron microscope (SEM). A numerical shape coordinate system (SCS) was also developed and applied to 300 particles from each sample. Statistical analysis was then performed on the collected data and characteristics of the MGD and LGD samples were compared.

Jan 1, 1995

By Peter McKenna

A mineral rights holding can ultimately only be turned to account by the profitable mining of ore on that property. The evaluation of South African gold mineral rights properties must therefore be carried out by assuming that they have potential to form part or all of a future gold mine. Such analysis involves the simulation of many of the estimation procedures that are normally carried out in a full feasibility study of a new mining venture but using far less data. This paper describes in detail the evaluation procedures that may be applied to an individual property and then indicates how these techniques can be applied to a whole mineral rights portfolio.

Jan 1, 1989

By Thomas M. Tharp, Mark A. Travers

A new method is presented for precracking three-point bending specimens for fracture toughness testing. A notched specimen of rectangular cross section is placed on a flat loading platen, with paper between specimen and platen. The specimen is loaded from above through a roller placed directly over the crack. The thin, high compliance joint between specimen and platen causes a distributed load on the bottom of the specimen. This results in bending at the cracked section and crack initiation at the notch tip. Since the joint is thin, its stiffness increases rapidly with deflection and crack propagation in the specimen generally remains stable and controllable. Fracture toughness KIC in a sandstone directly overlying the No. V coal was measured to be 0.27 MPa m 1/2. Even for cracks 1 cm long this value of KIC results in substantially lower effective tensile strength (modulus of rupture) in roof beams than is expected from intact rock strength.

Jan 1, 1986

By G. A. Doyle

Until the suspension of conventional operations in 1996, the White Pine Mine was the second-largest active underground copper mine in the United States, underlying an area of approximately 30 km2 (13 sq. miles) in the Upper Peninsula of Michigan. The mine operator intends to initiate in-stope solution copper mining by circulating a solution (lixiviant) of mine water, sulfuric acid and ferric iron through rubblized ore. As planned, the solution would be retired in the mined-out stopes following completion of the solution-mining activities. Investigations into the fate of the retired solution indicated that the solution, through time, would change from an acidic, metal-rich solution to a near-neutral, reducing solution containing much lower concentrations of metals. Investigations included reaction-path modeling (EQ3/6) and laboratory and in-mine tests. The combination of neutralization and reduction will result in precipitation of most metals, primarily as metallic sulfates, chlorides and sulfides.

Jan 1, 1997

By W. I. Enderlin, P. O. Jackson, J. A. Glissmeyer, K. B. Olsen

A reliable estimate of radon emissions to the environment from underground uranium mines was obtained through measurements of radon in ventilation air at 24 mines and from estimates of radon release from other mine sources. The total production of U308 from the mines sampled represents about 63% of the total U.S. production from underground mines (1978 statistics). Wide variation in the radon emission rate per unit of production was found from mine to mine. Using the total radon emitted and U308 produced by all mines sampled, an average of 26.7 Ci of radon was emitted per ton of U309 produced. The investigation includes a brief study of the sources of variation of the emission rates. A statistically significant relationship was found between the measured radon release rate and the cumulative ore production at several mines.

Jan 1, 1981

By Zhang Youdi

According to general guidelines, deposits suitable for surface mining can be divided into two basic categories: horizontal or flat-bedded deposits and inclined or dip-buried deposits. A series of mathematical models for surface mine long-term planning (SMLTP) has been developed and can be used for any kind of deposit. The basic theory and methodology of the models are oriented- graph simulation which combines graph and network theory with a systems simulation technique to form a new approach. From the viewpoint of surface mining and long-term plan modeling, the main differences between the two categories of deposits are analyzed, an important algorithm is put forward, and the structure of the models and some results of applications are introduced. Dynamic and comprehensive optimizations have been completed by the SMLTP model series. Combining different OR branches, the new approach has been proved to be a powerful tool to solve the strategic problems of surface mine planning.

Jan 1, 1989

By F. M. Doyle, Robert G. Robins, E. Peters

Stability diagrams for the Cu-S-H2O system have been widely applied over many years. Stability diagrams for aqueous systems generally, have been generated by computer, but with the programs for Potential-pH diagrams in particular, a common routine leads to error in multi-element systems. In this paper these errors, and some misinterpretation of diagrams are considered. In most of the published diagrams for the Cu-S-H2O system there has been no account of the sulfide complexes of copper. Here, the free energies of formation for the various species in the system have been re-evaluated for consistency, and some diagrams for the Cu-S-H2O system ( generated with the program DIASTAB Vers.5 ) are presented.

Jan 1, 1993

By James C. Burrows, Frances Kramer Mesher

Tungsten-containing ores are mined on all continents of the world. China is the world's largest producer and controls the world's largest reserves. The USSR, itself a sizeable producer, is estimated to be the world's largest consumer. The major use for tungsten in the noncommunist world is in production of cemented tungsten carbides for cutting, drilling, and wear parts. Other major uses include lamp wires, steels for tools, and armaments. Real tungsten prices have been in a general decline since 1977-1979 as the tungsten market undergoes basic and lasting structural changes.

Jan 1, 1986

By V. L. Jr. Davis, F. L. Stanley, P. J. Bethell

Fwe 3 m (10 ft) diameter Microcel™ flotation columns were installed at Clinchfield Coal Company's Middle Fork preparation facility in order to reduce product ash and increase recovery and plant capacity. The Middle Fork facility is utilized for the recovery of fine coal from a feed stream that consists primarily of 1 .5 mm x 0 material. The columns replaced conventional flotation cells for the treatment of the minus 150 pm fraction while spirals are used to upgrade the plus 150 pm material in the plant feed. The addition of the column flotation circuit resulted in an increase in plant capacity in excess of 20 percent while reducing the flotation product ash content by approximately 7 percentage points. Flotation circuit combustible recovery was increased by 17 percentage points. This paper discusses circuit design, commissioning, and sparging system design. Circuit instrumentation, level control, reagent system control, performance comparisons with conventional flotation, and general operating procedures are also discussed.

Jan 1, 1995

By P. Somasundaran

Flotation of oxide minerals is controlled by a number of factors, such as surface potential and solubility of the mineral, concentration and type of various inorganics, properties of the collector, pH, ionic strength and temperature. The role these factors play depends on the mechanisms of adsorption of the collector inorganics or polymer additives. The major mechanisms include electrostatic interactions, chemical adsorption, chain-chain interaction between adsorbed collector species and modifications of the surface by inorganics. In real systems, flotation is, however, markedly affected by various other processes, including aging of the minerals, surface precipitation of the collector on the mineral and associative interactions between various collector species leading to highly surface active, for example, ionomolecular complexes. These effects are reviewed here with selected examples.

Jan 1, 1999

Various computer packages are now available for balancing data obtained from complex concentration plants. It is well established that the filtered data generated by these programs are statistically better than the raw data. However the degree of improvement as well as the accuracy of the estimated variables depend strongly on the propagation of measurement errors through the estimation algorithm. Therefore, for the subsequent use of the filtered data, their confidence intervals are as important as the data themselves. Variance of filtered variables have been derived in a very general way for any arbitrary flowsheet and when data originate from various sources such as flowrates, chemical assays, particle size distributions and pulp percentages of solids. The theoretical formulae are incorporated in the BILMAT package for mass balance calculation and illustrated on various flowsheets involving grinding, classification and flotation. The validity of the proposed method is discussed by a comparison to a Monte Carlo approach, for a simple processing circuit.

Jan 1, 1986

By Walter Keune

Object Modeling Technique. This formal descriptive language makes it possible to formulate requirements in the real world in such a way that they can be implemented in the form of entities (cf. Entity Relationship Model[Che83]) and methods (see Figure 1). The object {Roadway} is graphically depicted by means of the Polygon method.

Jan 1, 1996

By Z. T. Bieniawski

Ground support requirements for safe and economical design of room and pillar coal mining layouts are reviewed. The design methods for mine roofs and mine pillars are discussed and the role of the geotechnical aspects is considered. It is shown that current support design procedures in the United States do not utilize fully the latest research findings and the need for more effective technology transfer in coal mine ground control is emphasized. Promising new developments in ground support are identified and possible research areas are suggested.

Jan 1, 1982

By Robert J. Timko, R. Lincoln Derick

This report presents a Bureau of Mines evaluation which examined the extent of gas leakage from sealed areas in underground coal mines and measured the effectiveness of commonly used structures for controlling the quantity of gas exchange from these areas. Evaluations were performed on five abandoned areas in two operating underground mines within the same coal seam. Methane and oxygen levels inby the seals were monitored to determine if the gas leakage was unidirectional or bidirectional. Results from this and prior work dealing with minimizing gas leakage were then applied to a newly abandoned area. Also discussed are bulkhead site preparation, construction plans, techniques for monitoring the status of the atmosphere within the sealed volume, and a modified European method for controlling gas migration from the sealed volume to the active mine.

Jan 1, 1991

By T. N. Patra, Sanjeeva Latchireddi, B. K. Mishra, Sravan K. Prathy

The motion of grinding balls has been the subject of study since 191 9 when Davis published the first treatise on this subject. Subsequently came the notion that knowing mill power draft, using Bond equation or others, is sufficient to do an analysis of grinding. Next, population balance models provided accurate scale-up from small laboratory size mills to very large plant size mills. However, this success was not repeated when dealing with semiautogenous grinding mill. The study of charge motion with the discrete element method provides support and answers to such issues. Besides providing an accurate picture of charge motion in large mills, the method begs the investigator to study grate and pulp lifter equally critically with fluid dynamic principles. Hence, in recent years, the field of comminution in grinding mills is advancing on a firm footing.

Jan 1, 2005

By J. M. Scharer, Bruce E. Halbert, Lysane Bouduc, Douglas B. Chambers, Jennifer L. Kirkaldy, Carol M. Pettit

Io contrast to acid mine drainage (AMD), neutral mine drainage (NMD) has not yet received widespread attention. Metal and sulphate concentrations can be elevated and of concern in neutral drainage from waste rock and tailings. In the present paper, metal release in high ionic strength mine drainage at neutral pH is evaluated at several mine sites. Specific factors including oxidation rates, buffering capacity, and hydrology are also addressed and their effect on the production of contaminated NMD from mine wastes is evaluated. Case studies are presented involving current seepage water quality and predictive geochemical modelling to illustrate the possible time frame and magnitude of the contamination.

Jan 1, 2000

By Adolf J. Jonaitis

Outokumpu developed TankCell flotation cell technology beginning in 1990, following 35 years of successful flotation cell experience and application. In 1994, Outokumpu proved favorable operating success of 100-m3 (3,500-ft3) TankCells for porphyry copper and zinc flotation. In 1995, evaluation of a 150-m3 TankCell led to the successful application of these large cells in several operations. More than 350 TankCells of 100 m3 and larger in volume have been installed and are in operation. Key features of the Outokumpu TankCell design will be described. In addition, discussion of operating data from various metallic mineral flotation operations worldwide will be presented. Large flotation cell development continues today, with operating cell volumes of up to 160 m3 (5,500 ft3) in operation.

Jan 1, 1999

By D. R. Nagaraj

Literally thousands of new flotation agents, both collectors and modifiers, have been proposed for sulfide and non-sulfide flotation over the past six decades since the beginning of the use of soluble surfactants in flotation. In stark contrast, the number of flotation agents used in practice is small. Xanthates and fatly acids, along with a few well-recognized modifiers, dominate the industry. Three major questions will then arise: a) are there truly specific needs in the industry that call for chemistries that are different from those used currently ? b) if yes, given the track record in the industry, what is the likelihood that such different chemistries will ever be used and to what extent ? and c) is more research into developing new chemistries necessary ? A critical assessment of flotation agents in general is made in this paper to provide answers to these questions and to identify the major factors that are responsible for the large disparity that exists between flotation reagent research and commercial usage.

Jan 1, 1994