Search Documents

By Zhengjie Chen, Wenhui Ma, Jijun Wu, Kuixian Wei

The gasification reactivity of PC (petroleum coke), strengthened by addition of different potassium carbonate proportions using different grinding medium, was investigated by using thermogravimetric analysis (TGA). Results showed that the gasification reactivity of PC not only increased with the increase of catalyst-loaded, but also showed the effective improvement by anhydrous alcohol. The PC was mixed with potassium carbonate [K2CO3] catalyst at 0.5%, 0.8%, 1.0% and 1.5%, and then ground wet with distilled water. The CO2-gasification rate of PC was only 77.35%, 80.55%, 84.07% and 85.88% under the gasification temperature 1100 °C and holding time 120 min, at different K2CO3 respectively. However, when the PC was ground in anhydrous alcohol at the same condition of catalyst-loading, the gasification rate of PC reached 95.43%, 96.63%, 95.50% and 95.61% at the holding time of 108 min, 101 min, 74 min and 35 min, respectively. It was shown by FTIR, SEM and EDX determinations that the anhydrous alcohol used as the grinding medium can further improve the gasification reactivity of PC when compared with the distilled water.

Jan 1, 2016

By X. J. Wu

Effects of various factors such as diaphragm materials, composition of electrolytes and current density on copper electrowinning from cupric chloride solutions was investigated. It is found that the crux of this process is to prevent the dissolution of copper by cupric ion and the formation of suspended CuCl precipitate. A process with high difference of copper concentrations between the feed solution and the spent electrolyte was selected. With this process, in which the feed solution contains 90 g/dm3 [Cu"], 3M NaC1, and 10mg/dm3 bone glue, and the spent electrolytes contains 10 g/dm3 [Cul, a very smooth and dense copper cathode can be produced with current efficiency above 93% and energy requirement less than 1.7 kwh/kg Cu at 25°C with N2 sparging. If a slightly higher energy requirement is permitted, smooth and dense copper cathodes can be produced at the current density up to 800 A/m2 with the identical solutions.

Jan 1, 1991

By Luis W. Pommier

The developed processes, the subject of this paper, extract the hydrocarbons, halogenated organic compounds and metal contaminants from hazardous soils, rendering them non-hazardous and ready to be placed back on the ground. The processes first segregate a non-contaminated fraction from the contaminated soil. This initial task is performed using available minerals processing technology: sizing, gravity separation, magnetic separation, froth flotation, etc. The remaining contaminated fraction, is submitted to two leaching operations for the removal of organic and metal contaminants, whenever both are present or to a single leaching operation if only one type of contaminant is present. The decontaminated soil fraction is mixed with the non-contaminated fraction and is placed back on the ground. The leaching liquors, used at neutral pH, are non- hazardous. After decontamination the liquids are processed to extract the contaminants, now valuable materials, for commercialization. Organic contaminants are removed by distillation of the solvents. The metal contaminants are precipitated in their oxide form. In both cases the regenerated solvents are recycled. The decontamination processes are economically competitive with transportation and disposal of the soils to permitted facilities for hazardous materials, and most importantly the developed processes remove the liabilities from the Responsible Parties. The law establishes that these liabilities do not disappear with either fixation nor with transportation and disposal since the environmental liabilities are of the ? cradle to grave? type.

Jan 1, 1994

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to to7 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003

By Uday B. Pal

In the electrochemical vapor deposition (EVD) process, gaseous cation precursors are passed over one side of a porous substrate, and oxygen is passed on the other side of the substrate. The gases diffuse and react within the porous substrate, and the pores get filled with the desired solid oxide. Subsequent solid state electrochemical transport through the solid oxide in the pores continues the reaction, and the film grows over the porous substrate. The EVD process has been used to deposit lanthanum chromite interconnection films and yttria stabilized zirconia electrolyte films over porous air electrodes. The EVD growth of these solid oxide films is found to be parabolic in nature, which indicates that the solid state transport (diffusion) of ions through the film controls the growth. This solid state transport can be analyzed using Wagner's treatment of the electrochemical transport. Conductivity measurements and the information on the defect structure of the oxide can be combined with the EVD growth rate measurements to calculate the solid state transport properties (transport numbers and partial conductivities) of the rate-controlling minority species in the oxide. Using this approach, the EVD growth of other electronic, mixed conducting and ionic solid oxide films can also be analyzed.

Jan 1, 1992

By Patrick Clark

As part of the Mine Waste Technology Program (MWTP), a large-scale column test using bacteria and a sulfide ore was conducted at McClelland Laboratories, Inc., in Sparks, Nevada. Four technology providers participated in this demonstration. A mining company in Nevada provided the sulfide ore, process effluent and make-up water. A process effluent column, a chemical oxidation column, and the four biological treatment columns were set side by side on a test pad outside the laboratory building. The process effluent and chemical oxidation columns were used for experimental control. The goal of this project was to evaluate the viability and feasibility of using these biodegradation technologies to reduce the cyanide to the regulatory level of 0.2 parts per million (ppm) within an acceptable timeframe and with low operational costs. The column testing began on December 3, 1998 and operated until May 17, 1999. One technology provider reached the regulatory level within the 158 days. The remaining three biotechnology columns were approaching the regulatory limit at completion of the demonstration. The MWTP is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered through an interagency agreement with the U.S. Department of Energy (DOE).

Jan 1, 1998

By H. Matsuda, T. Iwashita, H. Awata, H. Liwei, D. Hirabayashi, Y. Saito, S. Ozawa, Y. Goto

"The present study is concerned with investigating the effect of chemical treatment on enhancing the HCl absorption capacities of coal burnt ash and slag. It was found that the HCl absorption capacity of coal burnt ash discharged from fluidized bed combustor was improved by hydration with water and 5% polyethylene glycol solution. This phenomenon was based on an increase of the specific surface area of treated coal burnt ash. The HCl absorption capacity of hydrated ash with polyethylene glycol solution was almost equivalent to that of standard CaO and Ca(OH)2. In particular, the specific surface area of hydrated ash with polyethylene glycol solution was found to be 19 m2/g, which was more than over eight times larger than that of raw sample. Hydrated slag treated with lON sodium hydroxide solution also showed high HCl absorption capacity, with highly improved surface area. It was found that the absorption capacity of slag for HCl depended on the treatment time, showing the maximum absorption capacity for 12 hours of hydration treatment.IntroductionA large amount of coal burnt ash, slag and dust are discharged from such industrial processes as coal combustion and metal refinery etc., and it becomes an serious problem to recover and diminish these solid wastes because of the shortage of dump sites and subsequent metal elution to the environment. Figure 1 shows the present situation of reutilization of coal burnt ash and slag in Japan [1,2]. It is shown in this figure that these solid wastes are recycled as materials in the fields of earthwork, agriculture and forestry etc. A part of these solid wastes, however, is still dumped to landfill. To decrease this dumped amount, the development of environmentally friendly reutilization technique for these solid wastes is of great importance."

Jan 1, 2000

By Tullio Corsini

Scrap battery recovery process, developed by Engitec Impianti S.p.A., is improved transforming batches operations in continuous. Benefits expected: constant and better quality of the products; easier and more reliable control of the operating parameters, reduction of manpower requirements. Paste will content less sulfate, particularly in soluble form. Sodium sulphate is obtained with higher and constant purity.

Jan 1, 1993

By Xiangru Chen, Qijie Zhai, Wei Zhang, Haicheng Li, Chao Yang

In this paper, ductile iron material with different content of niobium was prepared by a scientific melting method. Image Analysis Software was used to studied the effect of niobium microalloying on both pearlite content and pearlite lamellar spacing in ductile iron quantitatively. The results showed that the addition of a small amount of niobium could increase the pearlite content and decrease pearlite lamellar spacing of ductile iron effectively.

Jan 1, 2015

By D. Silva-Galvan, R. D. Morales, S. Gonzáelez-López, A. Romero-Serrano, G. Plascencia-Barrera, F. Chavez-Alcala

This work is focussed on lead decopperising by two techniques: conventional top addition of sulfur and injection of sulfur powder. It is found that the first method proceeds under equilibrium conditions and the second one depends on kinetic considerations. Experiments were carried out using 15 kg lead baths at two temperatures, 340°C and 380°C. The carrying gas used for the injection trials was nitrogen at flow rates of 6.3 and 18.6 L min- 1• The results show that 'decopperising process is more efficient at temperatures close to the melting point of lead for the sulfur top addition process, whereas high temperatures produce better copper removal for the injection of sulfur powder. Besides, the sulfur injection with the higher nitrogen flow rate (18.6 L min-1) produced higher decopperising rates. Thermodynamic and kinetic models are used to simulate this lead refining process.

Jan 1, 2000

By Run-sheng xu, Hai-yang WANG, Di ZHAO, Teng-fei SONG, Jian-Liang Zhang

This paper was mainly focused on the different semi-cokes and charcoal which could be new fuels for blast furnace injection. Through the comparative study with bituminous coal and anthracite coal, the properties of semi-cokes and charcoal were presented in this research. 10 indexes of different fuels were obtained by different standard experiment, including proximate analysis, ultimate analysis, igniting point, explosivity, transportation characteristic, ash properties, grindability, calorific value, combustibility and reactivity with CO2. According to the data analysis, it provided a theoretical basis for rational utilization of various blast furnace fuels, and helped to broaden the scope of the blast furnace injection fuels. This research could contribute to energy conservation, emissions reduction, and sustainable development of iron and steel enterprises.

Jan 1, 2015

By Hüseyin Aydin

TWIP (Twinning-Induced Plasticity) steels have exceptionally good combinations of strength, ductility and damage tolerance which satisfy the recent requirements of automotive industries. Firstly, TWIP has the most beneficial effect on the work-hardening. It is believed that deformation twins increase the work-hardening rate by acting as obstacles against gliding dislocations. Moreover, TWIP steels have low to intermediate stacking fault energy and hence undergo extensive mechanical twinning during deformation, which in turn leads a good combination of both strength and ductility. To explain the mechanical characteristics and the mechanical behavior of the TWIP steels, we have been made some investigations and experiments that show the effects of microalloying elements and deformation mechanisms. In this study, three different compositions of TWIP steels have been produced. The microstructure and mechanical properties are characterized by using optical, electron microscopy and mechanical tests.

Jan 1, 2009

By W. G. Davenport

All Outokumpu flash furnaces burn some hydrocarbon fuel. Hydrocarbon combustion supplements heat from Fe and S oxidation and provides local heating in cool; parts of the furnace. Adjustment of hydrocarbon fuel combustion rate is an effective way of controlling furnace temperature. More oxygen and more oxidation of Fe?and S in the flash furnace continue to diminish the need for1hydrocarbon fuel. Still, as Tables 2.1 and 3.1 show, all flash furnaces use it. Oil is the most common fuel -natural gas, coal and coke are also used. This chapter demonstrates how hydrocarbon fuel is included in our flash furnace matrix. It shows that: (a) three new variables, mass hydrocarbonfoel. mass CO2 in offgas and mass H2O in offgas are inserted (b) carbon and hydrogen balances are added (c) hydrocarbon fuel quantity is specified (d) ,the oxygen balance is modified to include CO2 and H2O (e) the enthalpy balance is modified to include hydrocarbon fuel, CO2 and H20.

Jan 1, 2001

By Dean David

The evaluation of a new mineral sands prospect with unusual characteristics is described, The heavy minerals are very fine grained, have comparatively low average specific gravity (3.6) and are altered. Poor performance by conventional processing techniques made it necessary to trace the response of the major minerals during the separation processes, QEM*SEM® was used to quantify mineral volumetric abundances and mineral locking in magnetic and gravity separation products.

Jan 1, 1989

By N. Tsuchida

Sumitomo Metal Mining Co. Ltd. (SMMC) is currently developing the flowsheet to treat stockpiled limonite, a type of laterite ore, at Rio Tuba on southern Palawan Island, Philippines. The new plant will be commissioned at the end of 2004. Rio Tuba Nickel Mining Corporation (RTNMC) has been mining saprolite since 1977, and the limonite ore located above the saprolite ore body has been stockpiled separately according to nickel and magnesium content. Ore from these stockpiles will be blended and used for the operation. The annual production of nickel will be 10,000 metric tons for the next twenty years. The proposed process consists of ore preparation, high pressure acid leach (HPAL), counter- current decantation wash, impurity removal and sulfide precipitation. Precipitated mixed sulfide will be processed to electrolytic nickel by the Matte Chlorine Leach Electrowinning (MCLE) process at Niihama, Japan. SMMC has established new technologies during the process development, such as zinc removal and sulfide precipitation. Applying this technology, preferential removal of zinc can be achieved by hydrogen sulfide gas with negligible loss of nickel. Precipitation of nickel by hydrogen sulfide gas is carried out at low temperature. Slow kinetics is selected for control of the particle size of the precipitated mixed sulfide. Keywords: HPAL, Zinc Removal, MS Production

Jan 1, 2004

By Ali Nadir Khan

Depleting copper resources and advancing technologies have challenged industries to develop more viable, adaptable and cost efficient processes using also secondary raw materials in copper production. This study is targeting to that goal by dynamic modelling of flow and heat transfer coupled with chemical kinetics in an industrial scale flash smelting furnace settler using commercial CFD software ANSYS Fluent. First, different physical phenomena occurring inside the settler, for example, settling and separation of the matte/slag phases, and heat transfer between slag/matte phases and settler walls are studied. Secondly, reaction kinetics between matte and slag, and between slag/matte and settler walls, and impurity element distribution will be studied. This would also include phase changes phenomena due to these reactions and the flow of the reaction gases inside the settler. Settling of polydispersed droplets, their coagulation, breakage, and WEEE particle behavior are further targets of the modelling work.

By Yogeshwar Sahai

Submerged gas injection into melts contained in furnaces, ladles, or similar transfer vessels is commonly used in industrial practice. In this review paper, conditions leading to gas bubble formation at the nozzle are first summarized. The increasing gas injection rates and other conditions, such as nozzle size, lead to regimes which are commonly known as "bubbling" and "jetting". These are explained. The gas/melt interactions result in energy transfer to the melt. In recent years, a large number of researchers have investigated the relationships between the energy density and the mixing times. Their work is reviewed, and the mixing mechanisms is described. Finally, computational approaches of modeling submerged gas injection are briefly presented.

Jan 1, 1993

By Pesic. Batric

A novel chitosan-pyridoxal-epichlorohydrin was synthesized and evaluated in our laboratories. The evaluation was achieved by performing kinetic and equilibrium studies of copper sorption. The parameters examined were pH, temperature, concentration of copper, particle size and selectivity of copper sorption against iron, zinc, cadmium and cobalt. It was found that pH was the most important parameter, and sorption of copper increased with pH increase in the range pH 2.5-6.0. The low activation energy of the sorption reaction, 1 1.13 kJ/mole (2.66 Kcal/mole), showed that temperature was not an important parameter. The synthesized chitosan was selective against iron, zinc, cadmium and cobalt. The selectivity with respect to last three metals was achieved by the kinetic difference of sorption, as sorption of copper was much faster than for other metals. Iron (Fe2+) does not adsorb on chitosan. The mechanism governing the sorption of copper is intraparticle diffusion. This finding was supported by the dependance of copper sorption on the square root of time, the low activation energy, and the fit of experimental data in the diffusion through the product layer equation.

Jan 1, 1994

By C. J. Beyke

The U.S. Bureau of Mines has developed a process for the selective recovery of Pb metal from a mixed Pb-Zn concentrate. The concentrate was leached in recycled H2SiF6 at atmospheric pressure and 95° C with a redox potential of 570 mV (Eh). Eighty-five pct of the Pb was selectively leached from the concentrate while 87 pct of the Zn remained in the residue. Pressure leaching of the concentrate was slightly less successful, with 78 pct of the Pb leaching from the concentrate and 80 pct of the Zn remaining in the residue. Pure Pb metal was successfully electrowon from a purified PbSiF6-H2SiF6 solution with 96 pct current efficiency and 0.69-kW.h/kg energy consumption.

Jan 1, 1991

By Fashina Olugbenga Emmanuel, Ghazali Akeem, Adegbola Adekunle Amos, Omotoyinbo Joseph Ajibade, Olaniran Oladayo

"Modern engineering materials are required to be light weight and corrosion resistant, coupled with high strength and hardness. In this work, Al formed the parent metal and alloyed with 2.03% of Copper by sand casting process. The cast product 2024 was warm worked at various temperatures ranging from 300 to 5600c at 5%, 10%, 15% and 20% deformation respectively and aged accordingly. The results showed that the mechanical properties vis-à-vis hardness, tensile improved with increasing % deformation at a higher temperature. This was due to the progressive close-up of the voids emanated from casting by increasing deformation which is evident from the micrographs. MATLAB was also adopted to generate a model capable of determining the trend of flow of stress at operating temperatures. This was of immense value due to an increasing impact at higher percentage deformation with temperatures. Hence, Al -alloys will find applications in land vehicles, ships, trains, and aircraft, at elevated temperature.INTRODUCTIONThe problem of safe vehicle design with maximum impact energy absorption is a significant subject in structural crash worthiness design [1]. All engineering designs are expected to ensure the safety of users' life. This informed several studies meant to probe the causes of component failures in equipment, vehicles, and aerospace design and decide on appropriate solutions through materials selection techniques. A common example is in the design of crankcases and heads, piston, and cylinder blocks. As with engine blocks, cylinder heads can be made of Cast Iron or Aluminium Alloy. A head made of Aluminium alloy is lighter in weight than if it were made of Cast iron [2]."

Jan 1, 2013