Search Documents

By Steven M. Puricelli

Sulfuric acid plants associated with smelters, have historically been an overworked and often neglected pollution control device. They could do little more than manage the wide fluctuations in gas flow and SO2 strength from the smelter. With the introduction of flash smelting, the picture began to change, but the fluctuating batch converters continued to dictate acid plant design. More recently, the commercial use of continuous converting processes utilizing high levels of oxygen enrichment has dramatically upgraded the SO2 strength and stabilized the gas flow to the acid plant. The SO2 gas now issues continuously and at concentrations that allow for compact and, cost effective acid plants. Relieved of the burden of excessive dilution air, the heats of reaction can also be recovered as medium pressure steam and used to drive a generator, making the acid plant a net producer of power and a valuable asset to balance sheets. This concept was put into practice at the Kennecott Utah Copper Corporation smelter modernization project, located in Salt Lake City, Utah. The new acid plant, which was commissioned in June of 1995, is a sophisticated, low environmental impact, energy producing plant, worthy of review. This paper examines the key features of this acid plant, such as controlling its tail gas, by catalysis alone, to an environmentally friendly, 100 ppm of SO2, while feeding the acid plant converter with an efficient 14% SO2. The acid plant is also a prudent steward of energy resources, recovering 220,000 lb/hr of 140 psig steam from process heat which is used to generate a substantial 20 MW of gross power. Also discussed will be some of the ongoing issues, such as handling of selenium and fluorine in the gas cleaning sections, as well as a review of some. of the problems that were identified and resolved. Today's modem acid plants, by necessity, are becoming a producer of quality, valuable products, making the acid plant an asset and not a liability. Plants like Kennecott are already gaining wider acceptance and are expected to be the vision of the future.

Jan 1, 1998

By P. J. Uggowitzer, K. Steinhoff, A. Wolf

"With the increasing acceptance of the Thixoforging process in the last few years, also the technical and commercial requirements for this forming technology and its components increased. So far, a great deal of work has been done in the development of an efficient process and control design. However, less attention has been paid to the development of new specifically tailored aluminum wrought alloys for this specific manufacturing process. · In this paper a new AlMgSi-alloy (A6082), optimized for the Thixoforging process, is presented. In the first part, the technical potential of the new alloy is specified by its microstructural evolution and flow characteristics in the semi-solid state. In the second part, the mechanical properties of thixoforged components of different conventional AlMgSi-alloys a (e illustrated · and compared to the new alloy.IntroductionSemi-solid metalworking, also known as semi-solid forming, is a hybrid manufacturing method that incorporates elements of both casting and forging. The key to the process relies on the peculiar flow behavior of slurries containing non-dendritic solid, which was first studied at the MIT by Flemings et al. [i], in the early 1970s. It was discovered, that if an alloy is uniformly stirred during freezing, discrete rounded particles of solid are formed rather than the normal dendrites, and the slurry is highly fluid (-5 Pas) up at least 50% solid. In addition, these slurries posses thixotropic flow characteristics: the viscosity is dependent on sheare rate and time. The more vigorously they are stirred, the more fluid they become. However, on standing the viscosity recovers and the material stiffens (-106 Pas).The semi-solid forming process exploits this phenomenon. In a first step, the required non-dentritical- microstructure is obtained by mechanical or electromagnetic stirring during primary solidification of the alloy. The stirred slurry is generally fully solidified as a feedstock billet and - in a second process step - reheated above the solidus temperature into the semi-solid state. In this condition, the thixotropic properties permit the material to be handled by robotic devices and transferred to a die (Thixocasting) or subjected to- a forming process by means of forging (Thixoforging). Owing to the shear stress which acts on the semisolid material during forming operation, the viscosity of the material is reduced attaining so the desired fluid-like flow characteristics."

Jan 1, 2000

By S. Kang, D. G. C. Robertson

Slag cleaning furnaces require extensive wall cooling because they involve the use of a superheated slag bath. This is in direct contrast to smelting furnaces, where the wall is usually (but not always) protected by "banks" of solid charge. In order to understand the heat transfer and flow in slag cleaning furnaces a number of model studies have been carried out using molten wax to simulate the slag. Wax is a good model fluid because, like slag, it has a high Prandtl number. Wax models cannot simulate the behavior close to the electrodes (DC arc or AC submerged), but they can and do give a good simulation of the flow and heat transfer at the wall. An understanding of these phenomena is of great importance for the design of cooling panels in the walls of the furnace. Since superheated molten slag will eventually wear away any refractory bricks over time, the wall cooling must be designed to form a frozen layer of slag, referred to as a "freeze lining". The heat flux density (Q/A) required to do this is given by Q/A = h* ?T, where h is the heat transfer coefficient in the slag phase at the wall, and Li T is the superheat (bulk slag temperature - liquidus temperature). Both Q/A and h vary greatly with position and both are usually a maximum at the slag line. In the experimental work, molten wax baths were heated by block heaters to provide similar energy densities to those encountered in commercial slag cleaning furnaces. This procedure was considered to be valid since most of the electrical energy into a furnace bath is dissipated as heat. Gas stirring was used to simulate the gas evolved at the electrode in real furnaces - the quantity of this gas could be estimated from a knowledge of electrode consumption. The similarity criterion was equal gas flow per unit area of surface, in model and prototype. Heat transfer coefficients were measured in the models as a function of power density, gas stirring, superheat, etc., and could be related to the full-scale operations by the use of dimensional analysis.

Jan 1, 1999

By Michael A. Eamon

Magma Copper Company has operated its San Manuel SX-EW Plant facilities since 1986. The original plant facilities have a design capacity of 25,000 tons per year of electrowon copper cathode produced by processing pregnant leach solutions from an open pit/heap leach operation. In 1988, the plant was expanded to 50,000 tons per year to incorporate processing leach solutions from an insitu leaching operation. This paper presents a general overview of plant practices with particular emphasis on process innovations developed and implemented by Magma during construction and operation.

Jan 1, 1991

By J. W. Lyman

The U.S. Department of the Interior, Bureau of Mines, investigated methods to recover valuable rare-earth materials from NdFeB magnet scrap. Although several processing techniques were evaluated" the best separation of rare earths from the NdFeB magnet ,scrap was obtained by sulfuric acid dissolution followed by precipitation of recyclable rare-earth salts. Both sodium and ammonium intermediate double-salt precipitates' that can be converted to a variety of useful neodymium products were investigated. The sodium system showed a neodymium recovery of 98 pct, while the ammonium system yielded 70 pct during double-salt precipitation. The iron-rich effluent following the rare-earth recovery was treated to produce sodium and ammonium iron jarosites that can be disposed of or converted to hematite. By following this new procedure, many materials handling and economic disadvantages found with fluoride or oxalate direct precipitation were avoided.

Jan 1, 1992

By Emil B. Milosavljevic

The photochemical reactions of cyanide ion induced by light were investigated in the presence or absence of a titanium(IV) oxide semiconductor photocatalyst. The light sources employed were the sun and arrays of either mercury or fluorescent (cool white) lamps. The results obtained verify that cyanide decomposes much faster when TiO2 is present in the solution and that it is first oxidized to cyanate. However, contrary to the previous studies, it is established that cyanide is subsequently further oxidized via nitrite all the way to nitrate irrespective of the light source. As expected, the rates of the oxidation processes decrease with the illumination source utilized in the following order: Hg-lamps > sunlight > fluorescent lamps. As nitrate is a significantly less hazardous contaminant than cyanide, complete photocatalytic oxidation of cyanide to nitrate may be a viable method for decontamination of cyanide wastes. Contrary to previous claims, we find that cyanide is slowly photochemically decomposed even in the absence of TiO2. For example, with the mercury lamps as the light source, in two hours, cyanide concentration decreases to essentially zero; up to 7% was converted to cyanate and the remainder to unidentified products.

Jan 1, 1992

By S. R. Hutchins

Several refractory sulfide and carbonaceous gold ores were examined to determine whether microbial pretreatment could be used to enhance gold recovery. Test samples were biologically leached using unique. thermophilic microorganisms to solubilize iron sulfide minerals. Gold recovery from sulfide ores and concentrates was enhanced following pretreatment with the thermophiles; responses varied widely for the individual materials. Although bioleaching had little effect on the preg-robbing characteristics of the carbonaceous gold ores, cyanidation of the bioleached residues yielded higher gold recoveries than cyanidation of the native ore. By combining bioleaching with abiotic processes designed to inhibit preg robbing, gold recoveries of 83-98% were obtained from carbonaceous ores yielding 10-50% gold recovery by direct cyanidation.

Jan 1, 1987

By J. T. Stanley

The identification of crystal phases and crystal chemistry can be critical to understanding the mechanisms of waste material interaction with native soils. Understanding these mechanisms can suggest correct methods for remediation and treatment. A program is outlined and examples are given of the development of effective techniques for rapid phase identification of environmental samples using electron microscopy. The program concentrates on the development of integrated object oriented software to aid rapid searching of online databases and rapid simulation of potential crystal diffraction patterns. Examples come from dried sludge taken from a former hard-chrome plating facility.

Jan 1, 1993

By Garry W. Warren

The brass foundry industry produces a significant amount of waste sand containing Cu, Zn and Pb which is often classified as a hazardous waste due to Pb content. The potential application of a hydrometallurgical process to treat the sand by extracting metal values and thus detoxifying the material has been investigated. The process involves leaching of metal values followed by cementation. The emphasis of this investigation was on the leaching step, although some preliminary cementation experiments have been performed. In order for any alternative treatment scheme to be successful, the smaller size fractions of the sand must be addressed. Experiments have been performed on five individual size fractions using various lixiviants HCI, acetic acid and HCI/NaCI. Cu extraction was found to be slower than either Zn or Pb. Results obtained in this investigation indicate that copper is present in two forms, an oxide form which dissolves rapidly and is insensitive to the level of oxygen, and a less soluble form, probably metallic which dissolves more slowly and requires an oxidizing agent. The presence or absence of oxygen had no influence on the rate of Zn dissolution indicating that zinc is present mostly in oxide form. Toxicity Characteristic Leaching Procedure (TCLP) tests showed that residues could be produced which meet the toxicity limit for lead. Preliminary cementation experiments have also demonstrated the feasibility of Cu and Pb recovery.

Jan 1, 1991

By T. Maruyama

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. has been operating with one Flash Furnace (FSFE) and three Peirce-Smith Converters since its start-up in 1972. Anode production capacity has increased from 101,000 to 263,000 t/y by the several expansion programs, while converter capacity has increased and stable operation has been established by several improvements as listed below. - Expanding the furnace body (length) - Development of two kinds of automatic scrap charging system for each converter. (Increasing the in-stack time and better control of the melt temperature) - Oxygen enrichment at slag blow and copper blow - Increasing the blowing rate This paper reports the details of these improvements.

Jan 1, 1998

By B. G. Thomas

"Mathematical process models can be applied in several different ways to serve industry by inducing beneficial changes to process operation. This paper attempts to summarize the different uses, types, and attributes of these models, and to offer some ideas to consider when developing, using, and reporting on them. Process models range from empirical to mechanistic in nature and vary in complexity from simple analytical solutions to coupled, 3-D transient numerical simulations. They are classified here according to the way in which they are implemented in practice, viz. fully-online models, semi-online models, off-line models, and literature models. The purpose of the model should dictate how choices are made during its development. Ways to validate and compare the model with experiments are suggested. Examples are taken in the context of the author's experience in modeling the continuous casting of steel.IntroductionThe objective of this paper is to provide a partial introduction for this symposium by discussing some basic aspects of the application of mathematical process models in industry. Essentially, the aim is to explore how process models are used to benefit industry, and to offer some general comments and suggestions, based on the experience of the author, on how models can best meet this goal.This work is concerned with process models, which consist of systems of mathematical equations and constants that are solved on a computer to make quantitative predictions about some aspect(s) of the process. The specific variables required as input data and generated as output data are important features of the model. The equations often derive from a numerical solution to one or more differential equations and their boundary conditions. The model also includes the constants, which represent material properties, empirical relationships, and other knowledge about the process, and usually require considerable effort to obtain. Thus, general purpose commercial software packages, (ie. finite-element or finite-difference based codes), are not models in this context. They are useful tools, however, serving as frameworks for the development of process models."

Jan 1, 1994

By H. J. Roorda

With an increasing need to obtain metals by processing complex fine intergrown ores, the use of electron-optical techniques will become more important as a tool for mineralogical studies. Electron images enable a higher spacial resolution than can be obtained by optical microscopy and thus provide a powerful and necessary aid for the examination of small grains and finely locked particles. In this paper the mineralogy of Meggen ore was investigated. Both light-optical and electron-optical techniques were used to evaluate the mill feed and products of the concentrator. Detailed examination by reflected-light microscopy to assess the comportment of galena in the complex pyritic ore was inconclusive in establishing the cause for low lead recovery of only forty percent of the ore's lead content. Electron microprobe analyses indicated that the majority of the lead lost to the tailings was accounted for by extreme fine (often smaller than one micron) and complex intergrowths of galena in pyrite. The remainder was lost as fine free galena grains.

Jan 1, 1987

By Julian Johnson

The effect of changing redox potential (Eh) on the high temperature sulfuric acid leaching of Western Australian dry-land nickel laterite ores has been investigated. In particular, the effect of added reductant (sulfur, sodium sulfite) or oxidant (potassium chromate) on Eh, leaching kinetics, metal extractions, acid utilisation and leach residues has been determined. Three separate ores - nonhonitic ores from Murrin Mumn and Bulong, and limonitic ore from Cawse - were used in the study. Sulfur addition varied from 0 to 7.8 kg/t ore. The total acid loading was kept constant at 430 kg/t (Murrin Murrin ore) and 330 kglt (Cawse ore), whilst acid loading for Bulong ore was varied according to the presence of either reductant or oxidant. The extraction of both nickel and cobalt from limonite ore remained unaffected when small amounts of sulfkr were added, but addition of even small amounts of reductant to nontronitic ore decreased both nickel and cobalt extraction. Increased manganese and iron dissolution were observed as the levels of reductant increased, accompanied by a decrease in chromium dissolution. As the iron dissolution increased, free acidity decreased, with a subsequent decrease in nickel extraction. In contrast, addition of oxidant lead to reduced iron and manganese dissolution and slower extraction of nickel and cobalt. Keywords: Limonite, Nonhonite, Eh, Nickel Extraction

Jan 1, 2004

By Ramana. G. Reddy, Haoxing Yang

The electrodeposition of zinc from zinc oxide using urea and choline chloride mixture in a molar ratio 2:1 is investigated in different experimental variables, namely, the concentration of added [BMIM]HSO4, temperature, and applied cell voltage. The additive, [BMIM]HSO4, was determined to have beneficial effect on the current efficiency, energy consumed in the process and surface morphology of the deposits. The highest current efficiency (92.6%) and lowest energy consumption (2.92kWh/kg) was obtained for solution with 20mg/mL [BMIM]HSO4. The morphology showed the formation of absorbed additive layer on the cathode at higher concentration of additives. Experiments were conducted at different temperatures between 343K and 388K and at various applied cell voltages between 2.7V to 3.6V to determine the best experimental conditions. By varying temperature, highest current efficiency (91.3%) and lowest energy consumption (2.69 kWh/kg) was obtained at 373K. The electrodeposition process is enhanced between the applied voltage 3.0-3.3V by achieving lower energy consumption (2.75~3.06kWh/kg) and higher current efficiency (88.4~89.7%). SEM images showed grain size is significantly increased in higher applied voltages. While at higher temperatures, it seemed to generate particle growth as clusters at the outer deposit layer.

Jan 1, 2014

By J. R. Rendón

Cylinders of commercial aluminium alloy 6063 were homogenized under different conditions. The experimental results indicated that the general mechanical behaviour as related to curves of 0.2% yield strength, ultimate tensile strength and Brunnell hardness versus homogeneizing process is the same in both cases. The mechanical properties as compared to those required by plant specifications, tend to be better with increasing values of % Mg2Si in the alloy, as expected. The electron microscopy investigations revealed that in both homogeneizing processes the resulting microstructure consist of significant spheroidizing of the alpha phase (AlFeSi) and fine-needle type structure of beta phase. The alpha phase was also present in a Chinese type scripture. Furthermore, the slow cooling within the furnace resulted in the nucleation and growth of Mg2Si precipitates generally along the grain boundaries.

Jan 1, 1997

The high pressure acid leach process (HPAL) is being commercially used in four plants around the world to treat limonitic laterites. The two major operating costs of the HPAL process are the sulphuric acid and the energy required to heat the pulp to the desired temperature (>240°C). As an alternative to acid injection and steam heating, the in-situ generation of sulphuric acid and heat, produced during the high temperature pressure oxidation of sulphur-bearing materials blended with laterites, has been investigated at the laboratory scale. Various sources of sulphur have been examined, in particular, elemental sulphur, pyrrhotite and a Cu-Ni low-grade bulk concentrate. Under the proper blend ratios, all sulphur sources tested generated sufficient acid to result in equivalent nickel and cobalt dissolutions. A significant improvement to the process economics can result from the addition of sulphur sources containing valuable by-products, such as nickellcobalt andlor precious metals (gold and PGMs). This is especially true in the latter case, when the HPAL can be operated under Platsol conditions (i.e. with the addition of 5-10g/L of chloride), to dissolve the base metals and precious metals simultaneously in the autoclave. Various examples of the application of this concept are presented, together with a brief discussion of its implication on the autoclave design and the downstream processes to recover the values from the leach solutions. Keywords: limonite, co-treatment, acid consumption, sulphur, sulphur compounds, pressure acid leach (HPAL, PAL), Platsol process

Jan 1, 2004

By T. DebRoy

In recent years rapid technological advances have been achieved in the application of high energy density heat sources such as lasers and electron beams in diverse metals processing operations such as metal refining, fabrication, coating, surface modification and alloying. However, our phenomenological understanding of these new and emerging processes has not kept pace with the technological achievements. Inadequate understanding of plasma-metal interactions, the complexity of the component physical processes, and the scarcity of thermophysical data at temperatures much higher than the melting points of metals are the main difficulties in the comprehensive analysis of these processes. Several unique contemporary issues related to metals processing with high energy density beams such as rapid evaporation of alloying elements during processing and the role of plasma in influencing vaporization rate interfacial tension and species solubility in metals are discussed in this paper.

Jan 1, 1993

By E. N. Mounsey

Ausmelt Technology was selected by Bindura Nickel Corporation (BNC) as the basis for a new copper circuit to process nickel plant copper leach residue to blister, anode and finally cathode copper and recover PGM values at the Bindura Smelter Refinery (BSR). The process selected, based on Ausmelt Technology to smelt and convert the residue to matte and blister copper and produce a discard slag, is novel incorporating smelting, converting and slag reduction process steps in a single Ausmelt vessel. The process demands a high quality blister copper product with low levels of arsenic and nickel. This paper reviews the project and the initial operational results to the end of 1997 of the Ausmelt Top Submerged Lancing (TSL) smelter and discusses the implications for the wider TSL converter market.

Jan 1, 1998

By Wolfgang Baum

Case studies from epithermal gold-silver deposits in the western United States and in Latin America show that the routine use of process-related mineralogical studies has become an important tool for the reduction of development, capital and operating costs. Bypassing the mineralogical characteristics of epithermal gold-silver ores, as a result of fast-track development approaches, has resulted in multimillion dollar metal losses and/or in considerable modification costs of existing operations.

Jan 1, 1988

By John G. Reid

When the paper "Operations at the Greenvale Nickel Project Mine and Refinery" was delivered at the 1st International Laterite Symposium in February 1979, the Yabulu Caron plant had been operating for four years and production had just stabilized. The design had been based closely on the Caron plant at Nicaro, Cuba, built in 1944, also by Freeport. Yabulu had 10 Herreshoff ore roasters and production in 1978 was 18,682 tonne nickel as impure oxide sinter and 763 tonne cobalt in a mixed sulphide with a cobalt to nickel ratio of 1 :2.5. In the 25 years since the 1st Symposium, two more roasters have been added, but dry ore processing rate has remained relatively unchanged at 2.4M Uyr to allow a lower feed rate per roaster with associated higher recovery. The ore source has changed from the domestic Greenvale mine to imports from New Caledonia, Indonesia and the Philippines. Nickel production between 1978 and 2003 has risen by 67%, cobalt has risen by 146% and the products have changed to high purity nickel compacts and "ChemGrade" cobalt salt. The plant changes that have contributed to the increased recovery, production and product value are discussed. Keywords: Caron, Yabulu, nickel, cobalt, ammonia

Jan 1, 2004