Search Documents

By George Rice

INSTANTANEOUS outbursts of gas in underground workings are similar in effect to great blasts of explosives, but without heat effects. Fortunately they occur only in a few localities in exceptional coal fields of the world and under exceptional geologic conditions. Such violent outbursts should not be compared with the ordinary outflows of gas into coal mines or with explosions of gas and dust. The phenomenon is essentially one of gas held in circumscribed areas under very high pressure and as a mining face or heading approaches such a place and the mining excavation sufficiently weakens the natural surrounding dam or shell, this is burst by the pressure just as by the discharge of a mass of explosives. The outbursts, so far as known to the writer, have been confined to coal beds and have not occurred in other mineral deposits. Hence, as discussed later, he believes that it is the relation of the gases to the coal material that is a factor in conjunction with others in producing conditions which permit the phenomena to occur when mining is done. The gases in most instantaneous outbursts have been hydrocarbon gases but in two coal fields they have been definitely found to be chiefly or wholly carbon dioxide. One of these localities in which CO2 outbursts have been frequent and have caused loss of life is in the southern part of the Gard basin, near Alais, in southern France. In 1919, the writer visited the Fontaine mine in this field the day following the occurrence of an outburst by which two men were smothered by carbon dioxide and fine dust. After 24 hr. the CO2 had not been entirely removed by the ventilating current. Occasional outbursts of CO2 have also occurred in other small basins in France, causing accidents, as in Puy-de-Dome. However, mines in the Gard basin, north of those in which CO2 outbursts have occurred, have experienced hydrocarbon gas outbursts.

Jan 1, 1931

By M P. Sandy, R M. Stephenson

Portals to access underground mines are important infrastructure and their design requires careful consideration. Portals are generally expected to last for the life of the mine. Typically, the exposure of personnel and equipment is high, with many hundreds of movements through the portal per day. Consequently, the risk associated with geotechnical instability must be extremely low. Portals are often established from a boxcut. In areas where the weathering profile is well developed, the design and execution of the boxcut can involve significant effort, with the objective of minimizing the volume of the boxcut, whilst ensuring that conditions at the design depth are suitable for establishing a stable portal. Properly designed site investigations are a critical part of this process. Currently available portal design guidelines have not been updated for decades, however the equipment and ground support systems have changed significantly in recent years. Many mine portals have since been constructed in a relatively short time frame with success, often in challenging ground conditions using some of the more modern approaches to ground support. This is beneficial because delays in establishing a portal will generally delay other critical path activities, and lead to cost overruns.

Mar 15, 2021

By G. L. Oldright

This paper is the thirteenth of the series on Smelting in the Lead Blast furnace, and the third of the series on Handling Zinciferous Charges. Two other papers have been written on the Rate of Descent of the Stock Column, and Formation of Accretions. These are Reports of Investigations 2963 and 3094, for the Tooele plant and the Bunker Hill plant, respectively.

Jan 1, 1934

By G. L. Oldright

The data in this paper were collected at the Trail smelter of the Consolidated Mining & Smelting Co. of Canada, Limited, through the courtesy of S. G. Blaylock, vice president and general manager; James Buchanan, smelter superintendent; George Murray, assistant smelter superintendent; and the staff members given in Paper XI, Report of Investigations 3243. INTRODUCTION This paper is the thirteenth of the series on Smelting in the Lead Blast Furnace, and the third of the series on Handling Zinciferous Charges. Tyro other papers have been written on the Rate of Descent of the Stock Column, and Formation of Accretions. These are Reports of Investigations 2963 and 3094, for the Tooele plant and the Bunker Hill plant, respectively.

Jan 1, 1934

Using Dynamic Simulation Throughout a Process Plant's Life Cycle

Sep 13, 2010

By Resta S. A

Energy Resources of Australia Ltd - Ranger Mine is located about 255 kilometres east of Darwin in the Alligator Rivers Region of the Northern Territory. The Ranger project is surrounded by Kakadu National Park which is on the UNESCO World Heritage list. . Ranger Mine operates the largest uranium mine and processing plant in Australia. It is designed to produce 3000 tonnes of uranium oxide per year, but presently is producing a little less than one half that figure due to the depressed uranium market. The safety performance of the employees and Ranger as a whole continues to improve. The lost time injuries (LTI) have significantly reduced from 74 in 1985 to five in 1994. The total days lost due to LTIs have gone from 1543 to 14. These significant improvements have reflected directly on workers' compensation premiums in which a four-fold reduction has occurred. It is estimated that the actual monetary saving to the company is about $1.3 million per year and directly reports to the profit of the company. There is also an obvious and significant reduction in the less quantifiable costs such as the suffering of the injured employees and cost to society. The paper will review the various initiatives introduced and assess their effectiveness. Performance improvement is primarily dependent on the commitment, introduction of various initiatives and the subsequent change in workplace culture.

Jan 1, 1994

The Federal Coal Mine Health and Safety Act of 1969 limits to 2 milligrams per cubic meter (for dust containing a maximum of 5% quartz) the average respirable dust concentration to which individual miners may be exposed. Section 205 of the Act directs that an appropriate exposure formula for dusts with quartz content in excess of 5% be established. This formula, entered in F. R. Document 70-12351 filed September 16, 1970, is 10 milligrams per cubic meter divided by % quartz. Thus, the total respirable dust exposure permitted limits the quartz to a maximum of 100 micrograms. For example, if % quartz is 5%, 10 mg/5 = 2 milligrams, and (.05) (2 mg) = 100 micrograms. Similarly, if % quartz is 10%, 10/10 = 1, and (.10) (1 mg) = 100 micrograms, etc. If the % quartz is less than 5%, the 2 mg/M3 limit prevails.

Jan 1, 1974

An Appreciation of Dr. Douglas by Dr. ALBERT R. LEDOUX The Bulletins of the American Institute of Mining Engineers and the program of the International Engineering Congress, held last September at San Francisco, called attention to an important feature in the pro¬ceedings of the Congress; viz., the public presentation to Dr. James Douglas of the John Fritz Medal, for notable achievements in mining, metallurgy, education. and industrial welfare. Dr. Douglas' health, unfortunately, did not permit of his taking the journey to California. While he had been willing that the bestowal of the medal should be a public ceremony, his natural modesty made him shrink somewhat from what he considered something of an ordeal, and he begged those who were to take part in it to use restraint in anything which they might have to say as to his work and attainments. It was, therefore, with some considerable satisfaction on his side that he learned that the medal would be given him without a public, ceremony in New York, or elsewhere. . On Dec. 5, 1915, the writer of this had the pleasure of handing him the medal, certificate, and official letters of transmittal, at his home at Spuyten Duyvil, where lie was surrounded by his children and grandchildren, with one or two of his most intimate friends. He begged the writer to return his thanks to the Committee of Award; and again to express the feeling that nothing in his career merited so great an honor. On this point all of the members of the Institute will share the writer's feeling that Dr. Douglas is too modest. James Douglas was born at Quebec, Canada, in November, 1837. His father Was a distinguished physician and surgeon, employing his skill in the field of philanthropy: He established the first retreat for the insane in the Dominion, to which lie. devoted himself up to the time of his departure from Canada, when it was taken over by the Government. The son spent 2 years in study at the University of Edinburgh, which lie entered in 1855. Returning to Canada, he graduated from Queens University, at Kingston, Ontario, with the degree of Bachelor of Arts, having also studied medicine, and later theology. After his graduation he traveled extensively with his father in Europe and in the Orient, visiting Egypt several time's. They returned with important archaelogical collections, which Dr. Douglas subsequently donated to the Metropolitan Museum of Art in this city. He then returned to Edinburgh, where he continued his course in medicine, surgery being perhaps his chief interest at that time. He was subsequently licensed to preach and his contemporaries bore testimony to his broad philanthropy and to the sympathy which dominated his every act. His taste was distinctly literary; he had carried off a prize at Edinburgh in English literature.

Jan 1, 1916

By R. Hummel

When the slope angles of the southern side of the Venetia open pit were required to be flattened by some 20 degrees after an analysis completed by De Beers geotechnical engineering in conjunction with SRK, the additional waste stripping tonnage generated was in the order of some 70 million tons. The potential cost of having to move this tonnage had a significantly negative effect on the Net Present Value of Venetia Mine, challenging the viability of the third pushback and rendering a potential fourth pushback completely uneconomic. This paper details some of the innovation that went into the design and planning process undertaken to virtually negate the instantaneous effect of the flattened slope angles and the associated waste tonnage as well as further improve the NPV of Venetia Mine and bring the fourth pushback back into economic viability. This process has become known as NPV+ and is anon going exercise in waste reduction/deferment and revenue advancement.

Jan 1, 2001

By R. G. Jones

Many novel projects suffer delays, cost overruns or failure because of inadequately qualified technologies. A new qualification to measure the quality of innovation is discussed.

Jul 1, 2015

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

By R. M. Santmeyers

This paper presents one of a series of digests of foreign mining legislation and curt decisions that is being prepared in advance of a. general report relative to the rights of American citizens to explore for minerals and own and operate mines in various foreign countries. This interpretation of the mining legislation of Madagascar was prepared from the best information (in French) available in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers, to whom it dill be referred through the courtesy of the Department of State. INTRODUCTION The basic mining law of Madagascar is the decree of 1923, signed at Rambouillet by the President of France on July 19, and published in the Journal Official de Madagascar et Dependances. It has been modified by a number of subsequent laves and regulations, generally of minor importance.

Jan 1, 1933

By Ulick R. Evans

I Should like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country—researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. Films Produced at Elevated Temperatures If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By Ulick R. Evans

I Should like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country—researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. Films Produced at Elevated Temperatures If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By Z. M. Dai

Microorganisms in AMD (Acid Mine Drainage) were enriched in 9K culture medium. The enrichment was applied to leach copper pyrite after the microbial community structure and metabolism was stable. Before and after bioleaching, the microbial DNA was extracted and applied to RFLP (restricted fragment length polymorphism) analysis to demonstrate the relationship between the leaching efficiency and the change of microbial community. Atomic absorption spectrometry results showed that when concentration of the pulp was 10% and pH were 1.5, 2.0 and 2.5, the leaching rate were 56%, 57% and 34% on the 18th day respectively. These results indicated that the rise of pH resulted in the decrease of leaching rate. In lower pH condition, the growth of microbe was faster: when pH was 1.5, the microbial cell number reached to 1.4×107cells/mL on the 9th day; while pH was 2.5, the microbial cell number decreased to 4×106cells/mL. The analysis of microbial community structure showed that Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans were dominant species before bioleaching (account for 43% and 32% respectively). And after bioleaching, these two species were still dominant when the initial bioleaching pH were1.5 and 2.0. While the initial bioleaching pH was 2.5, the proportion of these two species decreased. These results demonstrated that the initial bioleaching pH would affect the microbial community structure in bioleaching system at room temperature, and this affect could lead to different copper pyrites bioleaching efficiency.

Jan 1, 2014

The first mention of gold in Western Australia was in 1848 when some specimens of copper ore, which are believed to have come from the Murchison district, were sent to Adelaide for assay. Gold was present in these specimens, but no particular interest seemed to be attached to this fact as the search at that time was mainly concentrated on base metals and coal. Interest appeared to be shown in gold in 1852 when several parties moved out eastwards from York looking for goldbearing country. Though these parties inmany cases were very near to what is now known as the Yilgarn Goldfield, nothing was found.The next record of gold was reported in some specimens which were brought in from Cardup, some 25 miles from Fremantle. Though this area was investigated, it would appear that all the gold had been contained in the specimens and nothing further was found, though the report had been the cause of a small rush of people interested in gold.From time to time specimens had been brought in by various people from the district east of Northam, and in 1861 a reward emanating from private sources was offered for the finding of gold within a radius of 150 miles from Perth. The Government at this stage took an interest in exploration for gold and in the same year supplemented this privately offered reward on a £ for £ basis. The Government also, about this time, commissioned a practical miner, with prospecting experience in the Eastern States, to examine the country between Albany and Northam with a view to the possible existence of goldbearing veins in that area. His report, however, was entirely unfavourable and nothing further was done. In 1873 a quartz lode was discovered near Albany arid a company was formed to work...

Jan 1, 1956

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"ABSTRACTTheoretical approach to estimate the ultimate pile capacity gives a rough idea at the initial stage of design that later on strengthen by the execution of static pile load test at site. The static pile load test is the only best option for the estimation of ultimate capacity of various types of piles. There are various methods based on strength, serviceability, net deflection for end bearing, shaft adhesion, graphical and extrapolation approaches for the interpretation of pile load test data to calculate the ultimate capacity. In this paper an attempt is made to evaluate the best-fit method for the estimation of ultimate capacity of single helix screw pile. The pile load tests on model scale were performed on screw piles of different helix diameter. The purpose of adopting model scale of testing was to achieve a state at which settlement increases without further increase in vertical load. The ground was compacted with dry sand at denser state. It was observed from the test results that extrapolation methods such as Chin- Kondner and Decourt predict the load settlement curve of screw piles very well, however ultimate pile capacity was on higher side which may not be suitable for the strength of helix plate. Decourt approach to plot the pile load data showed clear indication of the deformation of helix due to strong subsurface condition. A modified approach in Decourt method is proposed for estimating the ultimate capacity of screw pile having deformed helix whereas reduction factor is suggested for Chin-Kondner method for the estimation of ultimate capacity of intact screw pile.INTRODUCTIONDeep foundations are used to avoid the soft ground at shallow depth that is not suitable for carrying the structural load. Different types of piles have been used to transfer the load to deeper stratum. The screw pile is one of the new piling method and its use is considerably increasing. It consists of a cylindrical steel shaft with one or more helices at various length of the shaft. The diameter of helices (Dw) is usually 2 – 2.5 times the shaft diameter (Ds). The pile is installed to the required depth through torque and pressure. The advantage of screw pile over other piling system is its quick installation mechanism, high end-bearing and uplift resistance, noise reduction and minimum use of man power."

Jan 1, 2014

By Carsten Gerold

The paper is giving an overview about successful operating Loesche Vertical ? Roller ? Mills (VRM) installations and summarises the main benefits of the dry compressive Loesche grinding technologies in Airflow- and Overflow-Mode. Some of these benefits are optimised energy efficiency of the grinding - classifying - circuits, increased mineral recoveries and decreased OPEX costs, at a parallel simplification of the process route. Within this paper the process values of the Loesche VRM are compared to existing or planned conventional grinding ? classifying circuits. Further advantages discovered in pilot trials and examples for new more efficient process route alternatives are given. The paper reports about production and pilot trial experiences obtained by crushing and grinding Iron Ore, Iron Ore Concentrates, Copper Shale, Copper Matte, Copper Slag, Titanium Slag, Tin Slag, Steel and Stainless Steel Slag with Loesche VRM.

Sep 1, 2012

By B Belle

In a deep, gassy predrained coalmine, ventilation and goaf drainage systems act as critical controls to manage longwall (LW) panel return gas levels. The goaf capture efficiency of most LW panels ranges from 45 to 85 per cent based on the gas domain at respective workings. Recent operational experiences have indicated that 50 m goaf hole spacing is optimal for management of high production retreat gassy LW panels, where the probability of goaf hole failures are frequent. Due to the horizontal stress direction geotechnical issues, goaf hole failure just behind the LW face is a recurring challenge resulting in significant and immediate increases in LW panel return gas levels. This paper presents a successful implementation of an innovative LW tailgate (TG) road cut through seal goaf fan/venturi system. The system incorporated a 17' (400 mm cased) hole drilled to 320 m deep in a perimeter roadway on a retreating LW TG road drawing the working seam horizon goaf gas behind the perimeter of seals. The surface goaf fan/venturi system was aimed to safely exhaust the LW deep goaf gas and thus withhold the goaf stream spillage to TG drive area and reduce the panel gas load by controlled operation of the system using continuous monitoring of CH4, CO and O2 levels. This control philosophy was made operational without impacting the use of the perimeter inbye ventilation shaft used for mine cooling and providing additional ventilation dilution capacity. The instantaneous reduction in TG gas levels of up to 0.3 per cent was observed even when the LW was 300 m away from the c/t seal goaf hole. Success of this concept TG seal goaf gas control system used even when the LW was 1300 m outbye has become an inventory of additional control for future deep and long LW blocks. This paper attempts to share the design process in addressing other risks and desired outcomes in managing the LW gas levels.CITATION:Belle, B, 2015. Innovative tailgate mobile goaf gas management in two gate road longwall panels – concept to implementation, in Proceedings The Australian Mine Ventilation Conference, pp 31–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Andrew Stewart

The author desires to express appreciation to R. A. Cattell, C. T. Seibel, and H. S. Kennedy, of this Bureau, and to Dr. Richard Wiebe of the fixed nitrogen research laboratory, Department of Agriculture, for helpful criticism and comments in the preparation of this paper. More especially thanks are due to A A. Cattell for his many valuable constructive suggestions. INTRODUCTION From time to time, the Bureau of Mines receives inquiries from the non-technical public on the subject of helium. People ask for information concerning its properties; they want to learn Whence it is derived, how it is produced, and to what uses it may be put. In consequence, the following paper has been written to give in simple terms an account of this most remarkable of gases. It has been thought desirable for purposes of analogy to include reference to All the members of the group of elements to which helium belongs, and, incidentally, to embody in the narrative certain other information pertinent to the subject.

Jan 1, 1933