Search Documents

By C. Zener, J. H. Hollomon

IT Is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect o rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. EARLIER INVESTIGATIONS A clear analysis of the conditions necessary for plastic flow and for fracture was first given by Ludwik,1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis, both a flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracture is less than the flow stress and ductile if the reverse is true. According to Ludwik's analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence or now stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The. curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated' by the authors. According to this principle of equivalence, strain rate E and temperature T affect the flow stress only through a single parameter p of the form: p = EeQ/RT [I] In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. Combinations of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By William E. Ford, Edward Salisbury Dana

1. THE SCIENCE OF MINERALOGY treats of those inorganic species called minerals, which together in rock masses or in isolated form make up the material of the crust of the earth, and of other bodies in the universe so far as it is possible to study them in the form of meteorites. 2. Definition of a Mineral. - A Mineral is a body produced by the proc¬esses of inorganic nature, having a definite chemical composition and, if formed under favorable conditions, a certain characteristic molecular structure which is exhibited in its crystalline form and other physical properties. This definition calls for some further explanation. First of all, a mineral must be a homogeneous substance, even when minutely examined by the microscope; further, it must have a definite chemical composition, capable of being expressed by a chemical formula. Thus, much basalt appears to be homogeneous to the eye, but when examined under the microscope . in thin sections it is seen to be made up of different substances, each having characters of its own. Again, obsidian, or volcanic glass, though it may be essentially homogeneous, has not a definite composition corresponding to a specific chemical formula, and is hence classed as a rock, not as a mineral species. Further, several substances, as tachylyte, hyalome¬lane, etc., which at one time passed as minerals, have been relegated to petrology, because it has been shown that they are only local forms of basalt, retaining an apparently homogeneous form due to rapid cooling. Again, a mineral has in all cases a definite molecular structure, unless the conditions of formation have been such as to prevent this, which is rarely true. This molecular structure, as will be shown later, manifests itself in the physical characters and especially in the external crystalline form.

Jan 1, 1922

By Robert G. Van Nostrand, John H. Henkel

TRANSIENT potentials obtained in resistivity prospecting can be separated into two classes. The first is electromagnetic, has a comparatively short time constant, and increases in relative amplitude as the electrode separation is increased. These electromagnetic transient potentials, of which an excellent theoretical treatment is given by Yost,1 are the result of changes in the current and can be classed as differentiated signals. The second class is electrochemical, has a comparatively long time constant, and decreases in relative amplitude as the electrode separation is increased. The electrochemical signals are generated by the current flow itself and can be classed as integrated signals. The transient potentials due to electrochemical factors are the subject of this article. The phenomenon is referred to as induced polarization. Schlumberger2 was the first worker to observe induced polarization, but he was unsuccessful in attempts to apply the principles of induced polarization in electrochemical prospecting. Other workers, notably Bleil3 have studied polarization and in some cases pointed out its possibilities, but no theory has been presented that describes polarization and its time dependence adequately. It is the purpose of this discussion to present the essence of a theory to geo- physicists and to show that it leads to results consistent with experimental evidence. The theory on which this analysis is based has existed in electro- chemical circles since 1910.4

Jan 3, 1957

By Haim Chiswik

IN recent years considerable attention has been devoted to the devel-opment of new commercial uses for silver, chiefly because of lowered prices and large stocks of the metal. This has led to increased interest in the phase diagrams of silver alloys. The silver-lead diagram is reported' to be of the simple eutectic type, but no measurements of the solubility of lead in silver have been made. The solubility of silver in lead has been estimated2 from diffusion experiments and resistance measurements to vary with temperature from 0.09 to 0.18 atomic per cent (0.05 to 0.10 weight per cent). Silver-rich silver-lead alloys have recently been recommended as high-strength bearing metals.3 The silver-bismuth diagram is similar.' The solubility of bismuth in silver has been estimated to be about 5.5 weight per cent on the basis of X-ray work.4 Matthiessen5 found a solubility of silver in bismuth from 0.25 to 0.50 per cent by conductivity measurements. Silver and thallium form the same type of diagram,1 with no data on their mutual miscibilities. We have studied the first two of these diagrams by X-ray methods, verifying their main features and determining the solubilities of lead and bismuth in silver at several temperatures. We also determined the solubility of thallium in silver at one temperature. The solubilities of silver in lead and in bismuth were found to be too low to be detectable.

Jan 1, 1940

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Member, aged 25, recent graduate, with some experience in laboratory of steel plant, desires position as metallurgist or assistant in copper, aluminum, or steel works. No. 118. Member, aged 52, technical graduate, with 20 years' experience as engineer with coal-mining companies, desires position as engineer or superintendent of coal mine. No. 119. Member, aged 39, technical graduate, with extended experience in surveying, assaying, milling, and copper smelting, desires position along cyaniding, concentration, or copper-smelting lines. No. 120. Member, aged, 38, technical graduate, with several years' experience in research work, in mine operation and as professor of mining engineering, is desirous of engagement in planning concentration and metallurgy of odd and difficult ores. No. 121. Member, aged 32, graduate M. I. T. in mining and metallurgy, at present and for last five years superintendent of Western lead smeltery, will consider engagement with solid company, if opening promises advancement. Specialty, smelting of lead ores, high in lead and zinc content. Ten years' experience in the operation, design, and erection of a large lead plant. Now desirous of bettering position.. No. 122.

Jan 8, 1914

By R. F. Mehl, M. Gensamer

THE stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals1 has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.2 It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. ‡ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, whether deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of

Jan 1, 1938

By Eliot Blackwelder

For the purposes of this paper, the boundaries of China and Siberia will be taken as they stood about 1907. Except in the Caspian region, it is doubtful if all the oil ever produced in these countries would equal one day's flow of a good Texas well. Considering the vastness of the regions and the variety of strata, it seems strange that these two countries should have made so small a showing in the petroleum industry. No doubt the condition is caused partly by lack of prospecting and of modern methods of development; in larger measure, however, it is evidently because of unfavorable geological conditions over nearly all of east-central and northern Asia. CHINA The known oil occurrences in China are very few. For many years, perhaps a barrel a day has been obtained by primitive methods from wells near the city of Yenchang in the northwestern province of Shensi. A like amount was obtained from wells bored for salt water in the vicinity of Kiating in southwestern Szechwan. The little oil was separated from salt water by allowing it to stand in jars. The salt wells yield also considerable natural gas, which is used to evaporate the salt and also for domestic purposes. There is evidence that wells were bored in this part of China before the third century. It is said that more than 1200 wells have been sunk in that district to depths of 1600 to 2000 ft. (485 to 610 m.) in connection with the salt industry. The scarcity of petroleum in China may be ascribed to three general geologic conditions: First, China contains practically no marine sediments of Mesozoic or Cenozoic age; second, the Paleozoic sediments are not for the most part of the types that generally contribute petroleum; third, the rocks of nearly all ages have been strongly folded, faulted, and more or less intruded by igneous rocks in all parts of China except certain areas in the west and northwest.

Jan 7, 1922

By H. Le Chatelier

SILICA brick are indispensable in the manufacture of steel because they alone are able to withstand the high temperature of regenerative furnaces. All attempts to replace silica brick by other refractory materials for this purpose have failed, but the reason for this failure has remained obscure; we shall give an explanation later in this paper. Before the war, silica brick employed in France came principally from abroad, for which reason, since the beginning of hostilities, certain French steel works have been seriously handicapped. Our attention was first directed to the question by M. Bred, Engineer of the Teil Works. With him, we began certain investigations, at first using our laboratory and the furnaces of neighboring steel works. The larger part of our experiments, however, have been made in the laboratory of the Faculty of Sciences at the Sorbonne. For the heating of our samples, we are deeply obliged to MM. Charpy, Yeatmann and Guérineau. In undertaking these studies, our first aim has been to render assistance to French industry, by indicating, as precisely as possible, the necessary conditions for the manufacture of high-grade brick; but at the same time we have intended to give an example of the manner in which scientific methods may be put to practical application in the solution of industrial problems. Although our work has been confined to samples of only a few grams, we are nevertheless convinced that our information can be directly utilized by brick-works of which the output is measured in thousands of tons

Jan 9, 1918

By C. E. Schwab

A lead-zinc orebody, in fairly strong quartzite and with a dip of 35" to 60°, is block-caved by use of scrams in a stair-step pattern up the ore footwall. Scram linings to handle coarse muck and permit the use of folding scrapers are developed by the use of end-grain wooden blocks to reduce maintenance and keep operating cost to a minimum. THE Bunker Hill mine, since its discovery in 1885, has steadily produced a high grade of lead-silver-zinc ore. By the end of 1952 over 21,000,000 tons of this high-grade ore had been produced by square-set mining, and reserves in the mine continue to be very satisfactory both as to quantity and grade. For many years prior to 1941, mine production and mill capacity had been 1200 tons of feed per day. Closely adjacent to the mill, and stored behind dikes, coarse jig tailings had been impounded during the time preceding the advent of fine grinding and selective flotation. When manpower became short in 1941 and sink-and-float preconcentration was proved successful, mill capacity was increased to 1800 tons per day to treat these jig tailings economically. By 1946, because the supply of jig tailings was limited, underground exploration was started to discover and prove ore reserves of low-grade material which could be mined by an appropriate bulk mining method. During the years of square-set mining many possible areas of low-grade mineralization had been observed. One chosen for the first exploration work was sufficiently remote from active mining areas so that subsidence, if an ore-body were proved, would cause no problem. Also, old adits and workings were still open and in good enough condition so that exploration in the mineralized zone could be started with a minimum of preparatory work. In 1948 an orebody was proved of sufficient tonnage, of a grade about 2 pct Zn, 0.5 oz Ag, and 1.0 pct Pb. It was decided to use block-caving, the only appropriate mining method by which this grade of ore could be economically recovered. Exploration for additional reserves in other areas of the mine is continuing, but ultimate results are not known at this time. With more sink-and-float capacity, larger ball mills, and more flotation machines, mill capacity was increased to 3000 tons per day, permitting the mining of ore in the square-set area at a maximum rate not usually achieved, because of the scarcity of labor. Increased mill capacity also permits block caving and the mining of jig tailings at variable rates to keep mill feed up to 3000 tons per day. Fortunately the three types of feed are amenable to the same mill circuit and reagents for recovery of Pb and Zn. For example, during the first 10 months of 1952 square sets produced 827 tons per day, block-caving 1421 tons per day, and jig tailings 643 tons per day, an average daily production of 2891 tons for all three products. Exploration had proved the existence of an ore-body 1000 ft long and 165 ft wide in horizontal section, see Fig. 1. Company engineers were concerned only with the vertical extension, about 300 ft, from an old level to the surface. Much of this almost outcropped, Fig. 2. The ore lies in the hanging wall of a major fault of the Bunker Hill mine, standing at 65" in one end of the zone and separated from the fault by a wedge of waste, see Fig. 3. This wedge pinches out near the center of the zone, at which point the ore dips 45", lying nearly on the fault, Fig. 4. The remaining portion lies on the fault and conforms to the fault dip of 35", Fig. 5. Open-pit mining for the top of the ore was considered, but since the ore zone dipped into and under the mountains, adverse waste-to-ore ratios precluded use of this method. The ore occurs in massive quartzite of sufficient strength to support untimbered drifts, crosscuts, and raises. Zones of weakness in the quartzite are bedding, jointing, and small faults or slips. The mineralization, which occurs as small stringers of sphalerite and galena as well as pyrite, creates another line of weakness. The mineral veins or veinlets in themselves are high-grade. Their size and regularity and the amount of barren quartzite by which they are separated determined the limits of mineable ore, which are all assay limits except for the one determined by the major fault. Block 1 Without any background of caving in this type of quartzite, engineers selected the first block on the very steep end of the zone. Compelling reasons prompted this decision. The steep portion of the ore in Block 1 was of the lowest grade, so that if difficulties were encountered no very valuable ore would be lost, while the experience gained might be applied in mining the remaining blocks. A block 200x200 ft was laid out, with four scrams spaced 50 ft apart for drawing and placed at a right angle to the strike. Finger raises were placed in a 25-ft interval grid pattern, with flat undercutting done by crosscuts at the undercut level 25 ft above

Jan 1, 1954

By T. A. Klinefelter, O&apos, R. G. Meara, Glenn C. Truesdell, Richard W. Smith

The investigation of domestic talcs was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. 1, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for' aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." History The use of steatite and talc in ceramic bodies goes back a great many years. If pure, talcs shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a. large business was carried on in the manufacture of tips for gas burners.' With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Man-churian talcs. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1948

By T. A. Klinefelter, Glenn C. Truesdell, Richard W. Smith, R. G. Meara, O&apos

The investigation of domestic talcs was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. 1, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for' aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." History The use of steatite and talc in ceramic bodies goes back a great many years. If pure, talcs shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a. large business was carried on in the manufacture of tips for gas burners.' With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Man-churian talcs. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1948

By Francis Flynn

MANY excellent papers, descriptive of the milling and smelting of every kind of commercial ores, the refining of virgin metals, the casting into various shapes demanded by the trade, the rolling into shapes best suited to the factory machinery and the making of composition alloys to suit every requirement have been issued by the many technical societies dealing with non-ferrous metals. It is a wonderful collection of papers, of which the mining and metallurgical engineers may well be proud, but strange as it may seem, metallurgists in general appear to take the stand that when they have delivered suitable alloys to the foundry and rolled products to the factory their duty to write papers has ceased, at least in so far as the A. I. M. E. is concerned. Still we read in the daily papers that the mining companies are absorbing metal-manufacturing industries. The purpose of this paper is to describe the reclaiming of non-ferrous scrap metals at manufacturing plants, taking as an example the automobile industry.

Jan 1, 1929

By John G. Baragwanath

THE September issue of the Engineering and Mining Journal carried an item regarding the Cercapuquio Mining Co. which was mentioned as a large producer of lead, zinc, and cadmium, situated near Huancayo, Peru. The paragraph caught my eye because I had not heard of the property in thirty years and I recollect all too well the circumstances of its accouchement. In 1916 1 was making my headquarters in the town of Huancayo, then the terminus of the Central Railway of Peru, and was examining mines and prospects in that general area for Cerro de Pasco. In the course of my work I became acquainted with an engaging and energetic "practical" miner named Balarin, a Dalmatian living in Huan¬cayo, and made numerous trips in his excellent company. One day Balarin came to the down-at-heels hostelry where I stopped and told me that a Cholo prospector, a character by the name of Jose, had just reached town and claimed to have made a discovery in a little known locality called Cercapuquio. Lead-silver, Balarin said, and showed me a sample of galena about the size of his fist. "Fine," I remarked. "When do we leave?"

Jan 1, 1947

By W. Rostoker

Single isothermal sections were constructed for the titonium-rich corners of the systems Ti-Fe-O, Ti-Cr-O, and Ti-Ni-0 with a view to locating the shape and disposition of the ternary intermediate-phase fields for the compounds isomorphous with Fe3W3C. IN a previous note,' it was reported that a group of ternary intermediate phases existed which occurred in the general composition range Ti,X,O-Ti&O where X was one of the following elements: copper, nickel, cobalt, iron, or manganese. In two instances, binary intermediate phases occurred (Ti²Cu and Ti²Ni) which appeared to be isomorphous. The X-ray diffraction patterns of the phases could be indexed on a cubic lattice whose cell edge was of the order of 11 kX. Karlsson2 stated that the line extinctions and line intensities indicated that these phases were isomorphous with Fe³W³C and therefore belonged to the space group Oh. This author also noted that no unique phase of this type occurred at the composition Ti,Cr,O. This latter statement was accepted as true at the time the previous technical note was written.' However, work continued along these lines and that reported here has shown that a phase isomorphous with Fe³W³C does exist in the vicinity of the composition Ti³Cr³O but not at or near Ti4 Cr²O. The lattice parameter of this phase was found to be 13.01 kX. Metallographic examination of both as-cast and annealed specimens of these supposed ternary oxide phases disclosed structures which were far from single phase in many instances. It was considered a point of some interest to locate more positively the composition coordinates of the single-phase fields. To this end, single isothermal sections for the systems Ti-Fe-O (1000°C), Ti-Cr-0 (1000°C), and Ti-Ni-0 (900"C) were constructed. Phase relationships were studied by both X-ray diffraction and metallotrra~hic methods. Allovs were prepared as 10 g buttons by melting in a noncon-sumable electrode, water-cooled copper crucible arc-melting furnace using a helium atmosphere. Oxygen was introduced quantitatively by the use of weighed amounts of TiO² or TiO. Iodide titanium and the purest available alloying metals were used. All results are discussed in terms of the nominal composition of the melts. Previous experience with making oxygen-rich alloys had shown that oxygen losses were not significant if a homogeneous melt was produced. Weight-loss measurements were used to check loss in metallics during melting. Anneals were conducted in evacuated Vycor bulbs, and annealing times ranged from 24 hr at 1000 °C to 48 hr at 900°C. To achieve equilibrium in certain sluggish alloys, seven-day anneals were used. Debye-Scherrer powder patterns were taken in a 14 cm diam camera using filtered CuK radiation (K² = 1.541232 kX; K., = 1.53739 kX). Specimens were prepared by crushing and screening previously annealed buttons. In general, the X-ray diffraction results were used to identify the major phases, while the metallographic examinations were more useful in indicating the number of phases present. By the use of the combined results and general fundamental rules governing ternary equilibrium, it was possible to construct isothermal sections in good detail. In some instances where auxiliary lattice-parameter data were available, it was possible to lay down tie lines and to locate more positively corners of three-phase fields. Isothermal Section of the System Ti-Fe-O at 1000°C The binary systems Ti-O³ and Ti-Fe4 have been published. Binary phases, TiO, TiFe, and TiFe2, are likely to be encountered in the titanium-rich corner of the system. The structures are NaCl (Bl), CsCl (B2), and MgZn, (C14) types, respectively. Although preliminary X-ray diffraction studies indicated the presence of a ternary phase in the composition range Ti,Fe,O-TiJ?e,O, metallographic examination of two specimens at these compositions revealed the presence of other phases. Thirty-eight alloys were used to delineate the phase boundaries of the isothermal section illustrated in Fig. 1. The five almost single-phase ter-

Jan 1, 1956

In 1936 the Institute established the Anthony F. Lucas Gold Medal, which will be awarded from time to time "for distinguished achievement in improving the technique and practice of finding and producing petroleum." These awards will be sponsored by the Petroleum Division. Captain Lucas was a pioneer in the oil industry, one of the early wildcatters and a leading mining and petroleum engineer. He was famous as the discoverer of Spindletop. He became a member of the Institute in 1895 and in 1913 was the first Chairman of the Petroleum and Gas Committee of the Institute, the forerunner of the present Petroleum Division. He also headed the Committee in 1914, 1917 and 1918. The first medal was presented at the annual dinner in 1937, Feb. 17, to J. Edgar Pew. The personnel of the Committee on award as appointed in February, 1937, is as follows: John R. Suman, Chairman Until Feb., 1938 Until Feb., 1939 Hallan N. Marsh R. OgaRRio Russell 6. McFarland H. H. Power John R. Suman CaRl A. Young Until Feb., 1940 Until Feb., 1941 W. B. Heroy Joseph Jensen C. V. Millikan John M. Lovejoy J. Edgar Pew Carroll H. WEgemanN Members ex-officio R. C. Allen John W. Finch Axtell J. Byles H. B. FUQUA

Jan 1, 1937

By Robert A. Cook

Among the new devices for cheapening the cost of material entering into the manufacture of iron is the mechanical drawing of coke, by which the coke from bee-hive ovens is extracted with a minimum of manual labor. About twenty years ago, an ordinary plate-conveyer was put in use at the plant of bee-hive coke-ovens owned by the firm of Bell Bros. & Co., near Middlesboro, England. This conveyer ran close along the front of the ovens, and carried the coke to the cars. The ovens were drawn by hand, and a very great saving in cost was secured, as one man could draw and clean out twice as many ovens after the conveyer was put in use—he having no forking to do, and the coke being carried away as fast as it was drawn to the mouth of the oven. The next step was further to eliminate hand-labor as far as possible; and Mr. Thomas Smith of the Thorncliffe Iron Works, near Sheffield, patented in 1891 the machine for drawing coke which I here describe. This machine, the outcome of several years of experimenting, has now been in successful use since 1891, and there are between twenty and thirty of them in operation at present, and others building. The machine, as may be seen from Figs. 1 and 2, consists of a wedge-shaped shovel of proper width and thickness, connected with a steel rack of sufficient length to reach the back of the oven. The rack is supported by rolls, and guided by a device operated by a hand-wheel, which directs the shovel in the oven. The rack is driven by a pinion on a vertical shaft carrying a bevel-gear on the upper end. This bevel-gear is driven by another on the engine-shaft. The engine is single-cylinder, with reversible gear; and engine and machine are mounted on a truck, which is propelled

Jan 1, 1897

By J. J. Calaman, D. H. Fleming

DURING 1950 the jet-piercing process was used commercially in the piercing of primary blast-holes in magnetic taconite at the preliminary taconite plant of .the Erie Mining Co., Aurora, Minn. The Erie Mining Co. purchased a jet-piercing machine and associated equipment in 1949, and the machine has been in operation since its installation in the summer of that year. An overall view of the pit with the JPM-1 jet-piercing machine in operation is shown in Fig. 1. During three months of 1949 and continuously since February 1950, production piercing took place under all pit conditions. By the end of October 1950, a total of 15,000 linear ft of hole had been pierced in an open pit handling an average of 1200 to 1800 tons of crude a day in one 8-hr shift. While it is recognized that this output does not approach the millions of tons a year planned for the developing Minnesota taconite projects, the machine as a unit has been operating under conditions probably more adverse than those that eventually will be encountered in the large operations. This pilot operation has permitted evaluation of the piercing problem in the full-scale taconite plant. This paper describes jet-piercing process funda- mentals, important features of the latest jet-piercing burners and machine, actual piercing results obtained, and new developments that give promise of materially increasing overall process efficiency. To produce the blasthole, jet-piercing utilizes thermal energy, as contrasted with the application of mechanical energy in churn drills and jackham-mers. The heart of the process may be termed a tailored flame produced by a rocket-type burner, thermodynamically similar in every respect to that of the giant rockets being developed for military purposes. The heat release in the combustion chamber of the burner is about 50x10' Btu per cu ft per hr as compared with 5x10' for most modern steam generators.* Combustion of liquid petroleum fuels (kerosine, diesel oil, or No. 2 fuel oil) with gaseous oxygen in the burner chamber at pressures of 100 to 200 psi results in temperatures of about 4300°F. Expansion of the hot combustion gases through divergent nozzles produces high-temperature supersonic jets having measured velocities of about 6000 fps. Impinging the flame jets on rock causes a thin surface layer to expand and break away from the base as a result of the thermally induced stresses. This spalling action is aided further in chert and quartzite by the 0.82 pct volume change resulting from the 6 to p quartz inversion at 1066"F.t The dynamic action of the jets whisks the spalled rock

Jan 1, 1952

Edward Halse, Puerto Berrio, Colombia, S. A. (communication to the Secretary): I have read with much pleasure the interesting and valuable paper by Mr. Kunz, and hope that the following brief notes, gathered a few years ago, while a resident in Mexico City, may help to elucidate the subjcct: Turquoise.—This was known to the Aztecs as Xihuitl. Santiago Ramirez states that they found it in the Cerro Xicohtzonc, close to Atzcapatzalco, a suburb of the City of Mexico (compare page 59). Opal.—This was known to the ancient Mexicans, for they named it mezcuitlatt (compare page 63). Jade.—Under this was iucluded a third mineral, prehnite, not mentioned by Mr. Kunz. According to James D. Dana, part of the "jade " of China is prehnite; and Humboldt informs us, in his work on New Spain, that the same species of jade is known in some parts of Mexico as mahagua (majagua ?). The same writer says, in his Views of the Cordilleras, that the Aztec name Tecpatl included flint, hornstone, and green jade; and finally, in his Travels in South America," he discusses the nature of the ancient amazon-stones, and declares them to have been made out of a jade resembling " compact feldspar," one of the constituents of the gabbro verde di Corsica. IIence those stones were probably composed of nephrite. According to Humboldt, the form given to them most frequently is that of the Babylomian cylinder, longitudinally perforated, and loaded with inscriptions and figures. They were also cut by the natives into very thin plates, perforated at the center, suspended by a thread, and worn as amulets. According to the historian Clavijero, the specific name given by the Aztecs to the nephritic stone (jadeite) was Quitzalitztli,

Jan 1, 1902

By Roy E. Dickerson, W. M. O Connor

The production of crude petroleum of the Bacuranao field, Cuba, fell off rapidly because no new wells Mere drilled. In December 1938, the total was 15 bbl. per day. The estimated average from this serpentine field for the year is 20 bbl. per day. The Motembo area produced an estimated average of 160 bbl. per day. Production in July was 215,946 gal of gasoline, or 165 bbl. per day. In August production was higher because a new well in the concession, the Luisa Marcela, produced 189 drums the first day and required pit storage. The Atlantic Refining Company of Cuba started a deep test upon a long, narrow, surface-defined anticline 3 km. south of Remedios, a town on the north coastal plain of Santa Clara province, in December 1938. The Atlantic Refining Co. is doing extensive seismograph arid gravity-meter work in Matanzas arid Santa Clara provinces. The Shell company was rigging for a deep test in western Havana province at a location about 2 km. west of the town San Antonio dc los Banos New Petroleum Law More serious attention was given by some of the major oil companies to the development of petroleum in Cuba as a, result of the passage of a Petroleum Law ill that country on May 9, 1938. Under the old mining lam of Cuba, which gave no special treatment to petroleum, the usual provisions giving reasonably satisfartory guarantees to encourage investmerit of foreign capital were either entirely lacking or were 30 ambiguously expressed as to require legislative action. Under the new law, Government royalty is fixed at 10 per cent with the provision that it will be reduced to 9 per cent on crude petroleum that is refined in Cuba. Royalty to the surface owner is 1 per cent. A surface tax on a sliding scale from 10¢ to 406 per hectare per year is applicable to all exploitation concessions granted under the law or adapted to its provisions. So export tax is payable upon petroleum. Stability of taxation

Jan 1, 1939

By W. M. O Connor, Roy E. Dickerson

The production of crude petroleum of the Bacuranao field, Cuba, fell off rapidly because no new wells Mere drilled. In December 1938, the total was 15 bbl. per day. The estimated average from this serpentine field for the year is 20 bbl. per day. The Motembo area produced an estimated average of 160 bbl. per day. Production in July was 215,946 gal of gasoline, or 165 bbl. per day. In August production was higher because a new well in the concession, the Luisa Marcela, produced 189 drums the first day and required pit storage. The Atlantic Refining Company of Cuba started a deep test upon a long, narrow, surface-defined anticline 3 km. south of Remedios, a town on the north coastal plain of Santa Clara province, in December 1938. The Atlantic Refining Co. is doing extensive seismograph arid gravity-meter work in Matanzas arid Santa Clara provinces. The Shell company was rigging for a deep test in western Havana province at a location about 2 km. west of the town San Antonio dc los Banos New Petroleum Law More serious attention was given by some of the major oil companies to the development of petroleum in Cuba as a, result of the passage of a Petroleum Law ill that country on May 9, 1938. Under the old mining lam of Cuba, which gave no special treatment to petroleum, the usual provisions giving reasonably satisfartory guarantees to encourage investmerit of foreign capital were either entirely lacking or were 30 ambiguously expressed as to require legislative action. Under the new law, Government royalty is fixed at 10 per cent with the provision that it will be reduced to 9 per cent on crude petroleum that is refined in Cuba. Royalty to the surface owner is 1 per cent. A surface tax on a sliding scale from 10¢ to 406 per hectare per year is applicable to all exploitation concessions granted under the law or adapted to its provisions. So export tax is payable upon petroleum. Stability of taxation

Jan 1, 1939