Search Documents

By G. D. Boozer, W. H. Somerton

RESEARCH CORP., LA HABRA, CALIF. Thermal diffusivities of some typical sedimentary rocks have been measured by a rapid unsteady-state technique. Thermal data including diffusivity and conductivity are presented for the temperature range of 200" to 1,800°F. Diffusivities calculated from steady-state conductivity rneasurernents compared favorably with unsteady-state data at the lower temperatures. Unsteady-state data are less reliable at higher temperatures; reported values may be as much as 20 per cent high at temperatures in excess of 1,500°F. This is caused partly by the simplified method used in calculating diffusivity from experimental data and partly by the many thermal reactions which occur at the higher temperatures. The marked decrease in thermal diffusivity and conductivity at elevated temperatures indicates the importance of considering the temperature dependence of thermal properties in subsurface heat-transfer calculntions. Knowledge of the effects of liquid saturation, overburden and pore pressures, and heats of reaction of reservoir materials will be required before complete subsurface thermal analyses may be made. INTRODUCTION Heat-transfer calculations are becoming increasingly important in the analysis of in situ combustion and underground nuclear explosions. Thermal data for natural rock materials at elevated temperatures are generally unavailable. Calculations at high temperatures may be grossly inaccurate if temperature-dependent thermal properties of rocks are not considered. It is known that the heat capacities of rocks increase with temperature. Heat capacities may be calculated from chemical or mineralogica1 analyses of the rock system. Thermal bulk expansion of rocks is believed to be small, although few data are available. Thermal conductivities of most natural rock materials decrease with increased temperature. Thermal diffusivity, defined as the thermal conductivity divided by the product of the heat capacity and the bulk density of the material, is used in unsteadv-state heat-transfer calculations. It is apparent that thermal diffusivity decreases markedly with increased temperature. A new method, which gives a nearly continuous record of thermal diffusivity within the temperature range of 200° to 1,800°F and requires less than 1.5 hours for the run,' was used to measure the diffusivity of several sedimentary rocks. Thermal conductivities were calculated from measured bulk densities, heat capacities calculated from chemical analysis and the measured diffusivity values. Thermal conductivities were measured at lower temperatures by a steady-state technique1 to test the agreement of data obtained by the two methods.

By Alexander L. Holley

THE Pernot system of rotating and withdrawing the hearth of a Siemens regenerative gas furnace for the production of Martin or open-hearth steel, is, perhaps, the most conspicuous of the several improvements which have lately been made in the steel manufacture. These several improvements in the open-hearth plant are not combined in any existing works, but most of them will be combined in not less than three works now erecting in the United States; and it seems probable that their joint result will not only reduce the cost of products of ordinary grades to Bessemer rates, but that it will produce new and better grades of products. The open-hearth steel furnace and its operation are so generally understood that but a few words of general description are necessary. The ordinary furnace is not unlike the common reverberatory puddling furnace, except that an intense, uniform, and controllable temperature is maintained by the Siemens gas regenerative system. The materials. employed are various : melted or unmelted pig with ore, and with or without scrap; pig iron purified from silicon and phosphorus, with or without scrap; pig iron and scrap, melted together in a cupola, or charged hot or cold, together or separately, into the steel furnace; a pig-iron bath, and hot or cold steel or iron scrap, direct sponge or Catalan or puddled blooms charged into the bath. The operation is, to a greater or less extent, according to the nature of the materials used, a desiliconization and decarburization of the pig or other crude iron, and its dilution by already purified materials. Manganese is employed at the end of the operation to remove oxide of iron and silica, a regulated amount of manganese remaining in the product. Figs. 2 and 3, Plate IV, represent the hearth and roof of the Pernot furnace; Fig. 1 shows, in cross section, the general arrangeent of open-hearth plant with Pernot furnaces, as generally designed by the author, and now building at two works. The engrav-

Jan 1, 1879

By Dale Nix

DuRing the past year approximately 400 depth pressures have been recorded in the Yates field. Of these, 315 were "shut-in depth pressures," observed for the purpose of adjusting well potentials without making open-flow tests. The "shut-in depth pressures" were distributed one to each well and determined under as nearly uniform conditions as possible. Therefore, there is a scarcity of data applicable to production problems, other than the adjusting of well potentials. A few of the data obtained have been used in an attempt to solve some of the producing problems. These applications, however, merely indicate partial solutions and their review herein is to emphasize the variety of problems to which depth-pressure data can be applied, rather than to present conclusive solutions. Very little had been accomplished in the development of instruments to determine pressures within the well bore, when it was decided to obtain such information in the Yates field. Through the combined efforts of the Yates Engineering Committee and several producing companies, three methods of determining pressures in the well bore were soon developed: (1) the "compressor" method, (2) the "volume chamber" method, (3) the "depth-pressure recorder" method. "Compressor" Method.—A small volume compressor is used to inject gas into the tubing. The rate of injection is low so that the frictional losses will be reduced to a minimum. During the test, the pressures at the top of the tubing and casing are observed on recording pressure gages. .As the compressed gas depresses the fluid in the tubing, the pressure on the casing decreases while the tubing pressure increases. The tubing pressure becomes a maximum when the fluid level reaches the bottom of the tubing; and the casing pressure usually rises quickly as the gas breaks around the bottom of the tubing. The sum of the maximum pressure recorded at the top of the tubing and the pressure exerted by the weight of the compressed gas column is equal to the depth pressure at the bottom of the tubing. The procedure can be reversed;

Jan 1, 1932

By E. T. Dumble

(San Francisco Meeting, September, 1915) THE history of the several petroleum deposits of Texas and Mexico, or of the sediments in which they now occur, if the deposits are not indigenous to such sediments, is known in a general way only, but it nevertheless casts strong light on the conditions surrounding them and is of great importance in the search for and exploitation of then. The petroleum deposits of Texas are separable into two main divisions: 1. The deposits of northwestern Texas, which are directly connected with the Oklahoma fields to the north, and have no representatives at all in the Mexican area. 2. The deposits of the coastal area, which extend into Louisiana on the east and connect with those of the Mexican coast to the south. Early in the Pennsylvanian period a series of bituminous shales and limestones were laid crown over a broad area in Texas, Arkansas, and Oklahoma. These are known as the Bend series in Texas, the Caney shales in Oklahoma, and the Fayetteville beds in Arkansas. Following their deposition an uplift occurred, forming the Lampasas geanticlinal, which runs northeastward from the old Paleozoic land area of the Llano region toward Red River. The Bend series is petroliferous in places and has furnished a few producing wells on each side of the Lampasas uplift. This uplift forms the barrier and. dividing line between the two divisions of the Texas petroleum deposits. To the west of it, in waters which were the southern extension of the interior continental seas, in connection with the sediments and coal beds of the Pennsylvanian and Permian, great quantities of petroleum were deposited either as oil or as "potential petroleum." These sediments have been subject to very slight disturbance, and only very gentle folds. are found, with no signs of volcanic action in any part of the area. The conditions, therefore, indicate that the greater part, if not all, of the oil in this area is indigenous to the beds in which it is found.

Jan 8, 1915

By H. M. Chance

Within the last 10 years the subject of mine taxation in its relation to coal-mining interests has come to have growing importance, not only to those engaged in the mining of coal, but also to the owners of land underlain by coal.

Jan 1, 1915

By Peter J. Tarkoy

A commonly encountered difficulty in subsurface mapping and surveying of joints is the presence of steel conduits and rails, power lines and magnetic rock. Their presence often complicates and occasionally precludes the use of magnetic instruments such as a geologist's compass. An instrument was designed and built to overcome this problem by relating joint orientation geometrically to a known tunnel axis, track, or laser beam. Because of the unknown effect of magnetic bodies of rock, steel and high potential power lines, it becomes difficult or even impossible to make necessary compensations to compass readings. Therefore, relating a joint orientation directly to magnetic or true north seems impractical in underground joint surveying. But since the orientation of mine openings and tunnel alignments is generally surveyed and accurately known, it would appear to be a more practical axis of reference.

Jan 10, 1973

By C. A. Heberlein

C. A. HEBERLEIN,* New York, N. Y.-The results stated by Rey and Brevers are so startling that they are of great interest, as the concentration of a low percentage of cinnabar by differential flotation yields a high-grade concentrate in the presence of either arsenical or iron pyrite. The authors say: "Cyanide can thus be used to depress arsenopyrite and make a good cinnabar-arsenopyrite separation. A cinnabarpyrite separation could probably be effected in the same way." Corrosive sublimate at the present price of mercury would be a very expensive reagent but the expense would be justifiable if a high rate of concentration could be obtained with a high extraction. On my request, special tests were made in the Punitaqui mill in Chile along the line suggested by the authors, without any improvement of either grade or extraction. As the recovery of the cinnabar in a complex sulphide of chalcopyrite and pyrite gave unsatisfactory results, I had tests made at the testing laboratory of the American Cyanamid Co. at Stamford, Conn. As these tests turned out to be highly satisfactory, not only at Stamford but later at the mine, they are presented here. [AMERICAN CYANAMID TEST FEED PER CENT Si02 66.54 A12032.08 CaO0.70 MgO 0.00 Alkalis1.78 Fe15.63 Cu0.44 S9.42 Hg0.45 OZ. PER TON Ag0.95 Au0.151 Screen Analysis of Tailings, Per Cent Plus650.0 Plus 1001.32 Plus 15020.75 Plus 20019.85 Minus 20058.08] The pulp had a density of 22 and a pH of 7.8. Total time of conditioning was one minute. The reagent added was Texas fuel oil, 0.116lb. Of 33.7 Bé. gravity containing 0.9 per cent sulphur. Frother, 0.062 lb. of No. 5 pine oil. Rate of concentration of mercury was 25.7: 1 [ ]

Jan 1, 1941

By Paul Levin

A coal preparation plant built with conventional materials only might be able to do an efficient job of preparing coal, but its maintenance costs would be high and emergency shutdowns frequent. To remedy this situation special materials are being used, either in original plant construction or for replacement of conventional materials. The special materials vary from high-strength and abrasion-resisting steels and stainless steel alloys to ceramics. They include hard surfacing welding rods, rubber refractories and some of the newer plastics, the merits of which are cited by the author. A coal preparation plant, limited strictly to the use of conventional materials-for example, mild steel, cast iron and ordinary rubber-could, no doubt, do an efficient job of preparing coal, but the high cost of maintenance and increasingly frequent emergency outages would soon force the operator to seek relief by introducing special materials such as alloyed steels, oil-resistant rubbers and hard-surfacing welding rods.

Jan 6, 1964

By D. K. Das, P. A. Beck, S. P. Rideout

IN a previous publication1 1200°C isothermal phase diagram sections were given for the Cr-CO-Ni, Cr-Co-Fe, Cr-Co-Mo, and Cr-Ni-Mo ternary systems, in which the a phase formed narrow, elongated solid solution fields. The present investigation is concerned with the 1200°C isothermal sections of the Co-Ni-Mo, Co-Fe-Mo, and Ni-Fe-Mo ternary systems. A prominent feature of these systems is the presence of narrow, elongated µ phase fields. The crystal structure of the phase designated as µ both here and in the previous publication1 was determined by Arnfelt and Westgren.2 For the (CO, W)µ phase, named by them Co,W, (and also frequently designated as a), these authors found that the crystal system is hexagonal-rhombohedra1 and the space group is D53d — R3,. Westgren and Mag-neli3 later found that isomorphous phases exist in the Fe-W and the Fe-Mo systems (these phases are often referred to as < and E, respectively). Henglein and Kohsok4 stated that the phase described by them as Co7Mo,; (otherwise frequently designated as c) is also isomorphous with the above three. The Co-Fe-Mo system was investigated at 1300°C by Koester and Tonn,5 who found a continuous series of solid solutions between (Co, MO)µ and (Fe, MO)µ Koester6 also indicated similar uninterrupted solid solutions in the Ni-Fe-Mo system. However, since the Ni-Mo binary system does not have a phase isomorphous with F, Koester&apos;s diagram is expected to be erroneous. No data appear to be available in the literature concerning the Co-Ni-Mo system. The face-centered cubic (austenitic) solid solut,ions of iron, nickel, and cobalt, which are quite extensive in all three systems at 1200°C, are here designated as the a phase. The body-centered cubic (ferritic) solid solutions, based on iron, are designated in this report as the ? phase, in conformity with the nomenclature used previously.&apos; Experimental Procedure The alloys were prepared by vacuum induction melting in zirconia and alumina crucibles. The lot analyses for the metals used have been given.&apos; The number of alloys prepared was 46 for the Co-Ni-Mo system, 65 for the Co-Fe-Mo system, and 113 for the Ni-Fe-Mo system. The compositions of these alloys were selected with due regard to maximum usefulness in locating phase boundaries. The alloy specimens were annealed at 1200°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. Alloys consisting almost entirely of the face-centered cubic austenitic a phase, or of the body-centered cubic ferritic c phase were double-forged with intermediate annealing. The double-forged specimens were then final annealed for 90 hr at 1200 °C and quenched in cold water. Alloys containing considerable amounts of any of the other phases could not be forged. Such specimens were annealed for 150 hr at 1200°C and quenched. Microscopic specimens of all alloys were prepared by mechanical polishing, in many cases followed by electrolytic polishing. Description of the polishing and etching procedures used and tabulation of the intended compositions of the alloys prepared are being published in two N.A.C.A. Technical Notes.7,8 , Many of the alloys were analyzed chemically and, in general, the results are in excellent agreement with the intended compositions. X-ray diffraction samples were prepared by filing or crushing homogenized alloy specimens and by reannealing the obtained powders in evacuated and sealed quartz tubes. After annealing for 30 min at 1200°C the tubes were quenched into cold water. X-ray diffraction patterns were made with unfiltered chromium radiation at 30 kv, using an asymmetrical focusing camera of high dispersion. X-ray diffraction and microscopic methods were used jointly to identify the phases present in each specimen. The amounts of the phases in each alloy were estimated microscopically. The phase boundaries were located by the disappearing phase method. The results were used to construct 1200°C isothermal sections for the three ternary phase diagrams. The accuracy of the location of the phase boundaries determined in this manner is estimated to approximately ±1 pct of each component. The portion of the three phase diagrams lying between the µ, P, and 6 phases on the one hand, and the molybdenum corner on the other, has not been investigated. Recently Metcalfe reported0 a high temperature allotropic form of cobalt on the basis of dilatometric results and of cooling curves. In the present work no attempt was made to search for the new phase in the cobalt corner of the Co-Fe-Mo and Co-Ni-Mo systems. No alloy was prepared with more than 80 pct Co; the alloys used were intended to locate the boundary of the a phase saturated with cL. The microstructures of the quenched a alloys near the cobalt COrner gave no suggestion of an in-suppressible transformation On quenching. The location of the boundaries of the a + ? two-phase fields in the Fe-Ni-Mo and Fe-CO-MO systems was determined entirely by the microscopic method. The face-centered cubic a alloys near the ? field transform partially or wholly into the body-centered cubic ? phase on quenching from 1200°C to room temperature. The ? formed in this manner has an

Jan 1, 1953

By AIME AIME

COUNCIL.* PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1910.) VICE-PRESIDENTS OF THE COUNCIL. J. PARKE CHANNING NEW YORK, N. Y. FREDERICK W. DENTON PAINESDALE, MICH. JOHN B. FARISH DENVER, COLO. (Term expires February, 1910.) W. C. RALSTON..: SAN FRANCISCO, CAL. W. L. SAUNDERS NEW YORK, N. Y. H. V. WINCHELL ST. PAUL, MINN. (Term expires February, 1911.)

Jun 1, 1909

By Richmond Bennett

Airborne geochemistry became a reality with the advent of a high-sensitivity air¬borne gamma ray spectrometer with large volume NAI(Tl) crystal detectors. The high-sensitivity spectrometer measures small variations in the concentration of potassium (as Ks°), thorium (as Tl308) and uranium (as Bi.214) along the flight lines in the area surveyed. Hydrothermal dispersion patterns are indicated by anomalous measured values of the concentrations of potassium, thorium, uranium, or their ratios. In two recent Australian survey areas, copper mineralization was located along favorable structures within hydrothermal dispersion patterns delineated by airborne geochemical surveys. In metamorphic terrane where there had been po¬tassium metasomatism, the hydrothermal dispersion patterns were indicated by high potassium/uranium ratios (K40/Bi). In a sedimentary environment that had been intruded by a stock, the path of hydrothermal fluids was indicated by uranium (Bi214), thorium (TV&apos;), and uranium/ thorium (Bi214/Tl208) ratios.

Jan 1, 1972

By Brigitta Hassler

INTRODUCTION In the early 1960&apos;s research was begun in Sweden to improve the agglomeration of our domestic iron ore concentrates (5). Different agglomeration methods that were used in the building material industry were studied under the economic support from the Swedish Technical Council, the Swedish Board of Technical Development and by the Swedish industry. The research work was performed at the Division of Mineral Processing at the Royal Institute of Technology in Stockholm. All known agglomeration methods were reviewed and the methods were developed to produce superior quality agglomerates (6). The term cold bonding (in contrast to sintering) was introduced to describe the induration operation in these processes and this has been accepted internationally. Even though we used it mostly for steam autoclaving methods, it has come to describe a class of processes that use binding methods by pore filling. Schumacher in Germany discovered around 1907 that a strong material can be produced by mixing slaked lime with fine ground quartz and subjecting to a steam atmosphere under pressure at about 185ºC. This started development of lime-sandstone building materials and later on, in Sweden, the light-weight concrete. Schumacher also used the same reaction for briquetting iron ore concentrates by adding silica and lime, and autoclaving. The product seems to have been accepted for blast furnace burden and the process was used on an industrial scale until the 1920&apos;s. The sintering method has a small melting phase as diffusion medium and in the steam-autoclaving method a small quantity of water condensate at about 200°C serves the same purpose. Thus the induration process by the hydrothermal hardening methods is similar to that of sintering or heat treatment.

Jan 1, 1977

By Robert Gillham, Victoria Yablonsky, Grover R. Castle

INTRODUCTION The commercial paper market, unique to the United States, is a direct exchange of funds between high-grade borrowers and large lenders; because it eliminates both the bank&apos;s role as middleman and also some significant transaction costs, commercial paper is the lowest cost short term instrument in the world. For this reason, virtually all borrowers would like to enter the market, but only issuers with the highest rating from Moody&apos;s and Standard & Poor can attract purchasers at the best rates. COMMERCIAL PAPER The commercial paper market, in existence for over 100 years, has traditionally been used for short-term financings, with most paper maturing within 30-45 days. Under the U. S. Securities Act of 1933, (section 3(a)3) industrial paper can avoid registration only if it matures within 270 days and is used for current transactions. It was first used to finance the short-term seasonal working capital needs of manufacturing companies. Since World War II, commercial paper use has grown steadily, serving in the 1950&apos;s as the market in which finance companies financed the explosion in consumer credit purchases of heavy consumer durables. LETTER OF CREDIT BACKING As far as is known, the use of letters of credit to support energy-related commercial paper began about 13 years ago with an arrangement to finance the nuclear fuel for Con Edison&apos;s Indian Point 3 Plant. Goldman, Sachs was the architect of this financing and Chemical Bank provided the letter of credit support. After an early burst of interest, this type of financing wobbled severely in the difficult credit markets of the mid-seventies before regaining serious momentum in 1976 and 1977. A mining project would not normally qualify as a borrower in the commercial paper market because of its credit standing and because its large capital needs require long term financing. However, lately, commercial paper has begun to take the place of a bank term loan in limited recourse project financings. L/C backed commercial paper took this new and startling turn in 1982 when it was used as part of the $700 million financing for the development of the Newlands-Collinsville coal mines of Mount Isa Mines Ltd. in Australia. This was the first use of L/C backed commercial paper in a long-term limited recourse project financing. First Boston acted as financial advisor and, again, Chemical Bank provided sole letter of credit support of $155 million. The $785 million BHP financing for the acquisition of the Queensland (Australia) coal assets of Utah International from General Electric Company followed the next year; there we acted with two other Front Banks to provide $270 million of L/C support. These two important transactions indicate that not only has commercial paper become an integral part of a long-term financing package, but also that it is no longer the exclusive domain of the best known U. S. companies. Lesser-rated companies and a multitude of foreign borrowers have gained access to this "exclusive club." How has this become possible? OPERATION OF AN L/C An instrument of the commercial banks, the "direct pay" letter of credit, has enabled lesser-rated companies to issue commercial paper in their own names. The letter of credit allows the issuer to substitute the credit rating of the supporting bank for its own. The L/C in effect allows a lesser-rated company to rent the bank&apos;s credit rating. This upgrading is possible because the bank is unconditionally obliged to pay the note-holders at maturity and then turn to the Issuer for reimbursement. The Issuer commonly "rolls over" a new short-term issue and reimburses the supporting bank from the sale of the new issue until cash flows from the project allow the borrower to reduce the level of paper outstanding. The commitment for an L/C facility, up to 12 years in the case of the Broken Hill transaction, governs the life of the commercial paper tranche of the financing. The term of the L/C commitment thus has the power to extend the ordinary 30-45

Jan 1, 1985

By E. L. Kamen, H. D. Kessler, M. Hansen, D. J. McPherson

The highly reactive Ti-Mo and Ti-Cb alloys were prepared and heat treated under protective conditions. Phase diagrams were established based on micrographic and X-ray diffraction analysis and detection of incipient melting. ß titanium forms a continuous series of solid solutions with both molybdenum and columbium, whereas these metals are only slightly soluble in the a titanium modification. PREVIOUS work on the Ti-Mo and Ti-Cb systems was very limited and is discussed in succeeding sections of this paper relating to the respective phase diagrams. The diagrams in the present work were determined principally by micrographic analysis, because other methods such as thermal analysis and dilatometry are not suitable, due to the low diffusion rates of these alloys in the transformation range. X-ray analysis was believed less useful than micrographic analysis because: 1—On quenching certain high titanium alloys from above their transformation range, the body-centered cubic ß phase decomposes into acicular a (hexagonal close-packed) which room temperature X-ray diffraction techniques cannot differentiate from isothermal a. 2— High temperature X-ray techniques might be used, but are difficult to apply and are subject to error because of the high reactivity of titanium with gases such as oxygen and nitrogen. Although metallo-graphic study was the basic method used, X-ray diffraction analysis was applied to a limited extent, to further substantiate the findings. The transformation ranges on the titanium side of the Ti-Cb and Ti-Mo systems were studied both with DuPont Process A (magnesium-reduced) titanium alloys and with iodide titanium alloys. The Process A metal was used chiefly to bracket the transformation range in order to reduce the number of alloys given a particular treatment for the more accurate final study with iodide titanium alloys. Experimental Procedure The analyses of the metals used in the preparation of alloys for this study are presented in Table I. Melting Practice: Early in the work, a consumable electrode, arc melting furnace was used in the preparation of the Process A Ti-base Mo and Cb alloys. This type of furnace has been described by other investigators.&apos;, &apos; One of the major difficulties of the consumable electrode melting process was the prep- aration of homogeneous electrodes (with the mixture of coarse titanium sponge and fine powder alloying addition) which would give homogeneous ingots. Composition gradients encountered may have been due to a tendency for powdered alloying metals to drop away from the electrode in handling. This difficulty in the preparation of homogeneous alloys was overcome by the use of a nonconsumable electrode furnace for later work. This furnace is similar to the one used by Mc-Pherson and Fontana a Ohio State University. A diagram of the nonconsumable electrode arc furnace is given elsewhere.&apos; The source of power was a 400 amp dc welding generator. Electrode tips of tungsten (% in. in diam) were used for all columbium melts and for a limited number of molybdenum melts. Molybdenum tips were used for the majority of molybdenum alloy melts. Columbium tipped electrodes were tried, but disintegrated rapidly at currents above 300 amp. In the Process A titanium melting practice the metals were charged into the water-cooled spun copper crucible in the following forms: l—titanium: sponge (—4 + 16 mesh); 2—molybdenum: sections of 0.003 in. sheet (approximately ½ in. sq); and 3— columbium: powder compacts (? in. lumps broken from large section). After alternately evacuating and purging the furnace several times with argon or helium, the arc was struck against the metal charge,

Jan 1, 1952

By Granville S. Borden

THE program for income tax legislation presented here proposes some diminution in the current tax burden on mineral producers but it will, if enacted, eventually increase the potential and current Government revenue from the mineral industry.

Jan 6, 1951

By R. Stefanko, R. H. King, L. A. Morley

Coal mine fires, injuries and electrocutions, and many production delays have resulted from trailing cable splice failures. Research was carried out at The Pennsylvania State University to determine the failure causes and recommended solutions. The study revealed that current splice kit materials are generally adequate with the exceptions of connector flexibility, adhesives bonding, and abrasion characteristics of taped jackets. Research indicated that the most prevalent breakdowns result from workmanship defects. Therefore, guidelines for improved splice construction are reported in detail.

Jan 1, 1976

By AIME AIME

COUNCIL.* PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1910.) . VICE-PRESIDENTS OF THE COUNCIL. J. PARKE CHANNING NEW TORE, N. Y. FREDERICK W. DENTON PAINESDALE, MICH. JOHN B. FARISH DENVER, COLO. (Term expires February, 1910.) W. C. RALSTON SAN FRANCISCO, CAL. IV. L. SAUNDERS NEW TORE, N. Y. H. V. WIINCHELL ST. PAUL, MINN. (Term expires February, 1911.)

May 1, 1909

By F. G. Miller

The washabilities of typical bituminous coals are discussed in an effort to illustrate the importance of determining, by a complete washability study, the sulfur forms and their distribution in a coal. This study will then show the extent to which the sulfur can be removed. It should be emphasized that each potential application requires a thorough study because of the varying amounts of sulfur in different coals. It is not the intent of this paper to show the best results that flotation can produce, but rather to illustrate the potential of this process and point out the importance of improved flotation techniques where sulfur reduction is involved. It is generally accepted that sulfur exists in coal in three forms: (1) pyritic, (2) organic, and (3) sulfate sulfur. Sulfate sulfur usually makes up less than 1% of the total sulfur content. Pyritic and organic sulfur make up almost all of the total sulfur content, occur in varying amounts in different coals, and can vary greatly in coal of the same seam. Pyritic sulfurs of 20% to 80% of the total sulfur have been reported. Other authors have shown that it is not possible to remove the organic sulfur without chemically altering the coal. Chapman and ones&apos; state: "Organic sulfur, unlike pyritic sulfur does not exist as discrete particles, but is intimately associated with the coal structure, and as such it is not possible to remove it or reduce its concentration by physical means." Any success in removing sulfur has come about by removing pyritic sulfur by physical means; therefore, removal of sulfur in the pyritic form is the subject of this investigation. The extent to which any impurities can be removed from a particular coal can be determined by a washability study. Outside of crushing coal to finer sizes or chemically altering the coal, there are no known methods of changing this inherent washability characteristic. The efficiency of various methods used to remove impurities can be determined by comparison of results produced at a yield to the results as shown by a washability study. In recent years heavy media processes have proven their ability to wash plus 28 mesh coal and nearly produce results shown to be theoretically possible by the washability study. Therefore, it is the objective of this paper to show various methods of treating the finer fractions of the coal, in the hope of developing

Jan 1, 1964

By Frederic Benard

The electrolytic copper refinery at Copper Cliff, Ont., is operated by the Ontario Refining Co., Ltd. The associated companies behind the enterprise are the International Nickel Co. of Canada, Ltd.; The American Metal Co.; The Consolidated Mining & Smelting Co. of Canada, Ltd.; and Ventures, Ltd. The plant was the outgrowth of the rapid development of copper resources in the nickel-copper ores of the Frood and other great mines in the Sudbury district, and of the desire to have all primary production units grouped together as closely as possible. The refinery is near the intersection of the Sault Ste. Marie to Sudbury highway and the Canadian Pacific Railway. It is about one mile south of The International Nickel Company&apos;s smelter at Copper Cliff. The standard-gage track systems of the refinery and of the smelter are connected by a standard-gage timber railroad trestle that crosses the railway and the highway by means of steel girder spans. The Canadian National Railway has access to the plant by means of this trestle and the nickel company&apos;s tracks, so that the refinery has connections with both the Canadian Pacific and the Canadian National railways, as well as a direct connection with The International Nickel Company&apos;s smelter, from which the bulk of the copper to be refined is hauled by the latter&apos;s electric locomotives. Buildings The refinery (Fig. 1) covers approximately 60 acres, enclosed by an unscalable chain-link fence. The main buildings have a content of 23,000,000 cu. ft., with a total roof area of approximately 600,000 sq. ft. and near them are the substation, cooling pond and main standard-gage track system (Fig. 2). A ladder track for car storage extends 1200 ft. south of the coal-pulverizer tracks and the scale house is on this spur. The intake and pumphouse for fresh water supply are at Kelly Lake, about 3000 ft. south of the plant. Owing to the severity of the winters, when temperatures of from 20" to 40&apos; below zero are to be expected, the building of this refinery involved a number of problems in insulation, layout, ventilation, etc., which were

Jan 1, 1934

By C. R. Boyd

The region to which I have the pleasure of calling your attention, though limited in area, is remarkable for the quantity and purity of its mineral deposits, and in these respects it would be difficult to find its equal anywhere. IRON ORES. The red and brown hematites, pipe ore, and semi-magnetites, from which is made in charcoal furnaces the highest quality of iron for car-wheels, extend through the counties of Giles, Montgomery, Pulaski, Wythe, Smyth, Washington, Bland, Tazewell, Russell, Scott, Lee, Floyd, Carroll, and Grayson, Virginia, and run over into Ashe County, North Carolina. One locality of semi-magnetite, in the centre of the great Giles County basin, has in sight, by actual measurement, 50,000 tons of ore, which, according to Prof. Fesquet, contains 69.74 per cent. of iron and no phosphorus. In the great brown-ore belt, which passes through the counties of Montgomery, Pulaski, Wythe, Smyth, and Washington, there is an extraordinary deposit of more than a million tons. A small section of this very long vein, on Cripple Creek, in the County of Wythe, yields an ore which, analyzed by Mr. James Aumann, gave the following results: Metallic iron,........58.15 Water,.........12 96 Alumina,........2.32 Silica,.........1.09 Phosphorus,.. none. At one point towards the western end of Red Land Mountain, in Pulaski County, New River section, I measured a body of ore in this belt which will yield, to a depth of 150 feet, over 8,000,000 tons, and the deposit extends far below the 150 feet measured at the upper part. Again, at Rich Hill, near the mouth of Reed Island Creek, these veins show extraordinary surface development, giving an ore of very great purity. At numerous places, also, in the counties of Giles, Bland, Tazewell, Russell, Scott, Wise, and Lee, these brown and red iron ores are exposed in such vast quantities as to baffle both description and measurement. That of Chestnut Flat, in Giles County, back or west of the Angel&apos;s Rest Mountain, is an easily reducible ore, blood-red when crushed, of which there are fully 300,000 tons in sight. Its analysis is as follows :

Jan 1, 1880