Search Documents

By H. H. Evinger, M. Muskat

A method has been developed whereby one may calculate the productivity factors of producing formations from a knowledge of the reservoir conditions. Account is taken not only of the heterogeneous character of the gas-oil flow system but also of the detailed variations with pressure of the shrinkage and viscosity of the oil, the solubility of the gas in the oil, and even the variability of the gas viscosity and the deviation of the gas from ideal behavior. Curves are shown giving the results of numerical calculations on the production rate as a function of the pressure differential for a high-prcssure and a low-pressure system, three values of gas-oil ratio being treated in each case. Curves are also given showing the variation with distance from the well of the pressure, oil saturation, and permeability. The effect of connate water is briefly discussed in relation to the apparently large discrepancies between the calculated and observed productivity-factor values. Introduction The significance of the productivity factor as a measure of the capacity of an oil-bearing formation to produce is well recognized; for it is the composite and integrated resultant of the physical prop-crties of both the porous medium and the fluid stream passing through it with respect to the ease with which the particular petroleum fluids present in the formation can flow through it and into producing wells. The most direct method of determining the productivity factor of a well consists, as is well known, in the simultaneous measurement of reservoir-pressure differentials and rates of production and the expression of the data in terms of rate of flow per unit pressure drop.' Actual measurements carried out in this manner on producing wells have given factors that generally lie in the range of o to Ioo bbl. per day per pound pressure drop. This wide range arises not only from variations in permeability but also from the varying sand thickness of producing formations. One of the aims of developing a theory of the mechanics of oil production obviously is that of predicting what the productivity factor should be from a knowledge of the individual characteristics of the producing formation and the fluids produced. For homogeneous fluid systems passing through a porous medium into a producing well, it has been known for some time that the steady-state rate of liquid flow Q is given by the formula:* Q ? u log r?/r? where k is the sand permeability, h its thickness, µ the liquid viscosity, ?p the pressure drop between the well and the distant parts of the reservoir, in particular that at a radius re, and r? is the well radius. This gives the productivity factor: f= Q/kh?p ? 2p/µ log re/r? f=Q/ kh?p ? 2p/µ log re/r? which will have a numerical value for a

Jan 1, 1942

By M. Muskat, H. H. Evinger

A method has been developed whereby one may calculate the productivity factors of producing formations from a knowledge of the reservoir conditions. Account is taken not only of the heterogeneous character of the gas-oil flow system but also of the detailed variations with pressure of the shrinkage and viscosity of the oil, the solubility of the gas in the oil, and even the variability of the gas viscosity and the deviation of the gas from ideal behavior. Curves are shown giving the results of numerical calculations on the production rate as a function of the pressure differential for a high-prcssure and a low-pressure system, three values of gas-oil ratio being treated in each case. Curves are also given showing the variation with distance from the well of the pressure, oil saturation, and permeability. The effect of connate water is briefly discussed in relation to the apparently large discrepancies between the calculated and observed productivity-factor values. Introduction The significance of the productivity factor as a measure of the capacity of an oil-bearing formation to produce is well recognized; for it is the composite and integrated resultant of the physical prop-crties of both the porous medium and the fluid stream passing through it with respect to the ease with which the particular petroleum fluids present in the formation can flow through it and into producing wells. The most direct method of determining the productivity factor of a well consists, as is well known, in the simultaneous measurement of reservoir-pressure differentials and rates of production and the expression of the data in terms of rate of flow per unit pressure drop.' Actual measurements carried out in this manner on producing wells have given factors that generally lie in the range of o to Ioo bbl. per day per pound pressure drop. This wide range arises not only from variations in permeability but also from the varying sand thickness of producing formations. One of the aims of developing a theory of the mechanics of oil production obviously is that of predicting what the productivity factor should be from a knowledge of the individual characteristics of the producing formation and the fluids produced. For homogeneous fluid systems passing through a porous medium into a producing well, it has been known for some time that the steady-state rate of liquid flow Q is given by the formula:* Q ? u log r?/r? where k is the sand permeability, h its thickness, µ the liquid viscosity, ?p the pressure drop between the well and the distant parts of the reservoir, in particular that at a radius re, and r? is the well radius. This gives the productivity factor: f= Q/kh?p ? 2p/µ log re/r? f=Q/ kh?p ? 2p/µ log re/r? which will have a numerical value for a

Jan 1, 1942

By W. J. Garmoe

The Carr Fork mine is located approximately 50 kilometers southwest of Salt Lake City, Utah, in the Bingham or West Mountain District, adjacent to the Bingham open pit copper mine. Applied geology at Carr Fork, by Anaconda Minerals Company personnel includes detailed geologic mapping and sampling of underground workings, logging and sampling of drill core and cuttings, and the preparation and posting of geologic maps and cross sections for geologic interpretation, ore reserve calculation, mine operations, and long range planning. Accurate and easily understood graphic recording of Carr Fork geology is essential for optimum use by operating and engineering personnel. The design and implementation of exploration, development and definition drilling programs, research into geological spatial relationships, and analysis of structural complexities of the Carr Fork deposit are a1 so integral parts of the applied geology program.

Jan 1, 1984

By J. S. Bryner

In the study of metallographic specimens in the electron microscope, there is need for a method of locating the same field in both the light microscope and the electron microscope. This need arises chiefly from the fact that in the electron microscope the magnification and degree of resolution are so much higher, and the field so much smaller than in the light rnicroscope that it is often difficult, if not impossible, to identify positively what is being observed. The difficulty is increased by the fact that, because a transparent film replica of the metal surface must be used in the electron microscope, micro-constituents can be identified not by their color but only by their texture and contours. For these reasons it is desirable to obtain a series of photographs showing the same field in both microscopes in order that the appearance of common microstructures and micro-constituents in the electron microscope may be identified and catalogued for future reference. The need for a method of locating the same field in both microscopes arises also when it becomes desirable to enlarge in the electron microscope for more detailed study a particular interesting structure observed in the light microscope. Using the standard polystyrene-silicalJ replica technique, in which the silica film replica is fished from the ethyl bromide on a 1/8 in. diam zoo-mesh specimen screen, the possibilities of locating a particular area on the film in the electron microscope are rather remote. The desired structure may be obscured by the wires of the specimen screen or unrecognizable at the high magnification. A solution to the problem would be provided if a specially designed specimen screen, containing an opening which could be absolutely identified and quickly located in the electron microscope, could be fastened to the silica film replica in such a position that the desired field on the specimen would be located at the identifiable opening in the specimen screen. The design for such a specimen screen, a method for producing it, and a technique for fastening it to the silica film replica are described below. Description OF Method The Specimen Screen A simple design for a specimen screen containing an opening easy to identify and locate in the electron microscope is one with two lines of openings at right angles in the form of a cross. Such a screen is shown in Fig I. The opening at the center of the cross is identified easily and can be located quickly in the light microscope and in the objective image of the electron microscope. The specially designed specimen screens for this work were produced in quantity by electroforming. On both sides of a polished strip of copper I X 3 X 1/8 in., twenty patterns of the cross of openings were punched with a diamond point micro-hardness tester, using a load of magnitude

Jan 1, 1949

By Alfred H. Bell, Virginia Kline

In 1944, Illinois produced 77,413,000 bbl. of oil, or 4.6 per cent of the total for the United States, and continued to rank sixth in the nation in oil production. This represents a decrease of 6 per cent from 1943, when- the total Illinois production was 82,256,000 bbl. This decrease was much less than the 23 per cent decrease in 1943 from production of the previous year. The principal factor in arresting the production declinc, which had been going on since 1941, seems to be the increased drilling that followed the relaxing of the Federal Government's rules in regard to well spacing. The daily average production for 1944 was approximately 212,000 bbl. Daily averages by months were as follows: Jan......... 219,000 July........ 206,000 Feb......... 220,000 Aug......... 211,000 Mar........ 216,000 Sept......... 209,000 Apr......... 211,000 Oct......... 210,000 May........ 213,000 Nov........ 209,000 June........ 209,000 Dec......... 205,000 During the year, 1991 wells were drilled for oil and gas in Illinois as compared with 1791 in 1943, an increase of II per cent. Of the 1991 wells, 430 are classified as "wildcat" as compared with 461 in 1943. Twenty-eight new pools (Table 2 A) were discovered in 1944 as compared with 29 in 1943. Changes in federal drilling regulations, permitting closer spacing of wells, resulted in a drilling program that emphasized development of proved acreage rather than wildcatting. Data on production and drilling by fields are given in Table I; data on annual production and drilling for Illinois, in Table 3. Discoveries Twenty-eight new fields (Table 2 A), 42 extensions (Table 2 B), and 39 additional producing zones in existing fields (Table 2 C) were discovered in 16 counties in Illinois during 1944. Of the 28 new fields, one was abandoned during the year, 14 were one-well fields, eight others had not more than 6 wells, one had 8, one had 9, one had 11, one had 15, and the largest new field, Roaches North, had 28 producing wells at the end of the year. In all, 109 wells were producing in these new fields on Jan. 2, 1945, as compared with 111 wells producing from 29 new fields at the end of 1943. . The average initial production of the discovery wells of the 28 new fields was 129 bbl. of oil and II bbl. of water, a notable decline from the average initial production of 194 bbl, of oil and 15 bbl. of salt water for the 1943 discovery wells. In fields discovered since 1936, the total number of oil wells producing at the end of 1944 was 12,335. Productive Acreage The area of proved production in the new fields (discovered since 1936) increased from 144,335 acres at the end of 1943 to 173,485 acres at the end of 1944 (Table I), an increase of 29,150 acres. Of this increased area, 1720 acres are in fields discovered during 1944 and 27,430 acres are in extensions of fields discovered earlier.

Jan 1, 1945

By Albert B. Horn, J. J. McKetta, O. L. Culberson

Since water is present in natural gas and petroleum reservoirs, it is of engineering value to have accurate experimental data regarding the behavior of water in hydro-carbon systems. Since experimental data of this nature are so scarce in literature, a program is under way at the University of Texas to obtain experimental data regarding the distribution of water in petroleum hydrocarbons. This initial paper is subdivided into three parts: A. The apparatus and analytical procedure are discussed. B. The equipment has been checked by comparing the experimental data with data of literature on the solubility of methane in water at 77°F and pressures to 10,000 psia. C. Experimental data are presented at 100, 160, 220, 280, and 340°F on the solubility of ethane in water at pressures to 1200 psia. As the temperature is increased the solubility of ethane in water first exhibits a minimum and then a maximum solubility. The range of applicability of Henry's Law is discussed. INTRODUCTION Although considerable experimental data have been published on water-hydrocarbon systems in the hydrate region, the information on these systems in the vapor-liquid and the vapor-liquid- 'References are given at end of paper. Manuscript received at the office of the Petroleum Branch August 31. 1949. liquid regions at elevated pressures is extremely scarce. A survey of the literature on hydrocarbon-water systems at elevated pressures was presented by McKetta and Katz12,13,14 showing the systems and phases investigated. In addition to these existing published data, Poettman and Dean" have reported the water content of propane in the three-phase region (only the propane-rich liquid and the vapor phases were studied) and Michels, et al.15 have reported the solubility of methane in water at pressures to 6800 pounds per square inch at 77°F and at pressures to 1500 psia at temperatures to 300°F. It has been shown12,14 that the presence of water will materially affect the phase equilibrium of hydrocarbon systems. In order to make experimental studies on the quantitative effect of the presence of water in naturally-occurring hydrocarbon systems, it is desirable to have data available on binary hydrocarbon-water systems. A program is underway at this laboratory to determine the phase relations of the hydrocarbon-water systems. Initially the investigation will be limited to binary systems with water as one of the components. Later ternary and complex systems will be investigated and reported. EQUIPMENT AND ANALYTICAL PROCEDURE Apparatus In order to avoid a description of the methods employed in each subsequent paper, a description of the apparatus and the analytical procedure will be given here. The apparatus is shown schematically in Fig. 1. The numbered items in Fig. 1 represent the high pressure valves. The equilibrium cell is of the totally enclosed type, with a volume of 550 cubic centimeters. The cell is mounted in an air bath which in turn is mounted on pillow blocks and connected to a rocking mechanism so that the cell and bath will oscillate approximately 30 degrees above and below the horizontal at 35 oscillations per minute. The air bath is heated by two resistance heaters. The first or primary heater is 250 watts and is controlled by a thermoregulator; the second heater is of 500-watt size and is manually controlled to aid in bringing the cell to equilibrium temperature. Air circulation in the bath is accomplished by means of a fan. the shaft of which is concentric to the heaters. The walls of the bath are insulated with 2-in. thick blocks of 85 per cent magnesia. Temperature observations are made with three calibrated thermocouples. One couple is sealed in a well provided within the equilibrium cell, and is used as the criterion of the cell being at the equilibrium temperature. The other two thermocouples are located on opposite sides of the cell to indicate temperature uniformity within the air bath. The thermoregulator, used in conjunction with a relay, gives a variation in the temperature of the air in the bath of plus or minus one degree Fahrenheit. However, since the equilibrium cell weighs approximately 55 pounds, the

Jan 1, 1950

By Duncan MacVichie

THE iron fields described here are located in the Iron Springs and Pinto Mining districts, Iron County, Utah. This region is in southwestern Utah, about 260 miles south from Salt Lake City, and is reached by the Los Angeles & Salt Lake railroad of the Union Pacific system. The iron fields lie at an elevation of 5500 to 7500 ft. above sea level, and are essentially desert in character. They are covered with a light growth of sage brush, piñon pine, and scattered cedar. Weather conditions are unusually favorable for all-year mining operations, the winters being mild with little or no snow; and the summers not excessively hot, the temperature rarely rising to 100° during the day, while the nights are invariably cool. The iron-ore bearing area extends from the Iron Springs district to the Iron Mountain mining district, being approximately 25 miles long in a northeast-southwest direction, and from 1 to 3 miles wide in a northwest-southeast direction. In the Iron Springs and Pinto mining districts, the ore occurs at various points around three sides of Granite Mountain and Iron Mountain. This is readily understood by reference to Figs. 1-4. These mountains are composed of andesite, which has been forced up through the surrounding sedimentary formation, in the form of laccoliths. An extensive report on the geology of these districts was made by Leith and Harder,1 who state: The three dominating geological features of the district are three large andesite laccoliths which constitute the Three Peaks, Granite Mountain, and Iron Mountain; lying in a northeast-southwest line across the area in question. Three unconformable sedimentary series, aggregating 4000 ft. in thickness, outcrop in successive rings around these laccoliths, dipping outward asymmetrically, very steeply at the contact, less steeply further away. Still farther from the laccoliths, lava-flows 2000 ft. thick rest in nearly horizontal attitudes on the tilted sedimentary rocks. These general relations are modified by faulting. All of the rock formations of the district are more or less covered on the middle and lower slopes by unconsolidated and partly consolidated erosion debris, both aqueous and subaerial, which spreads out on the lower ground to make the deserts.

Jan 7, 1925

By D. C. Hilty

It has long been known that in melting high-chromium steels, some of the carbon might be oxidized out of the melt without excessive simultaneous oxidation of chromium, and that higher temperatures favor retention of chromium. The advent of oxygen injection as a tool for rapid decarburization of a steel bath permits significantly higher bath temperatures, and it was quickly recognized that the use of oxygen injection facilitated the oxidation of carbon to low levels in the presence of relatively high residual chromium contents. Up to the present time, however, specific data pertaining to the chro-mium-carbon-temperature relations in chromium steel refining have not been available. Individual steelmakers have evolved practices more or less empirically, but there has been very little real basis for predicting how effective any given practice can be in permitting maximum oxidation of carbon with minimum loss of chromium. The current investigation, therefore, was undertaken in an effort to establish the fundamental carbon-chromium relationship in molten iron under oxidizing conditions. As reported below, the equilibrium constant and the influence of temperature on that constant have been derived for the iron-chromium-carbon-oxygen reaction in the range of chromium steel compositions with what appears to be a fair degree of precision. The practical application of the result will be obvious. Experimental Procedure The laboratory investigation was carried out on chromium steel heats melted in a magnesia crucible in a 100-lb capacity induction furnace at the Union Carbide and Carbon Re- search Laboratories. The charges for the heats consisted of Armco iron, low-carbon chromium metal, and high-carbon chromium metal, the relative proportions of which were calculated so that the various heats would contain from approximately 0.06 pct carbon and 8 pct chromium to 0.40 pct carbon and 30 pct chromium at melt-down. When the charges were melted, the bath temperatures were raised to the desired level, and the heats were then decarburized by successive injections of oxygen at the slag-metal interface through a ½-in. diam silica tube at a pressure of 30 psi. The duration of the oxygen injections was from 30 sec to 2 min. at intervals of approximately 5 to 30 min. It did not appear that length or frequency of the injection periods had any significant effect on the results; cansequently, no effort was made to hold them constant and they were controlled only as was expedient to the general working of the heats. Between successive injections, the heats were sampled by means of a copper suction-tube sampler that yields a sound, rapidly-solidified sample representative of the composition of the molten metal at the temperature of sampling. This sampling device is a modification of the one described by Taylor and Chipman.1 An attempt was made to vary bath temperatures between samples, but it quickly became evident that, unless the variations were small or unless the new temperature was maintained for a minimum of 15 min. during which an injection of oxygen was made in order to accelerate the reactions, a very wide departure from equilibrium resulted. For most of the runs, therefore, temperature was maintained relatively constant at approximately 1750 or 1820°C. A few reliable observations at other temperatures, however, were obtained. Temperature Measurement The high temperatures involved in this investigation were measured by the radiation method, utilizing a Ray-O-Tube focused on the closed end of a refractory tube immersed in the metal bath. The immersion tubes employed were high-purity alumina tubes specially prepared by the Tona-wanda Laboratory of The Linde Air Products Co. These tubes were quite sturdy under reasonable mechanical stress at high temperature. They were unusually resistant to thermal shock, and chemical attack on them by the melts was slow. With care, it was found possible to keep these tubes continuously immersed in a heat for as long as 5 hr at temperatures up to 1850°C, before failure by fluxing occurred. The Ray-O-Tube—alumina tube assemblage was similar to those supplied commercially for lower temperature applications. In operation, the alumina tube was slowly immersed in the molten metal to a depth of approximately 5 in., and the device was then clamped solidly to a supporting jig where it remained for the duration of the run. A photograph of the equipment, in operation with Ray-O-Tube in place and oxygen injection in progress, is shown in Fig 1. When in position in a heat, the instrument was calibrated by means of an immersion thermocouple and an optical pyrometer. For calibration through the range of temperatures from 1500 to 1650°C, a platinum -platinum + 10 pct rhodium thermocouple in a silica tube was immersed alongside the alumina tube. Output of the Ray-O-Tube in millivolts and the

Jan 1, 1950

By J. Norman Bulkley

As electrical power is used to a greater extent on the Rand than in any other mining center, it is thought that a short description of the methods used and results obtained may be of interest. In comparing Rand practice with that on other fields, several general factors should be borne in mind: First, the mines are all working on large tonnages of low-grade ore (average. $6.50). The annual crushing rate is about 27,000,000 tons. Second, the mines are all grouped udder the financial and engineering control of mining houses, so that the results of a group, rather than an individual mine, are open for study, and practice follows more uniform lines. Third, coal of fair quality (about 12,000 B.t.u.) can be obtained for $2 to $3 per ton., Good supplies of condensing water are, however, scarce, and have to be carefully stored. Power Supply Power is supplied by the Victoria Falls & Transvaal Power Co., Ltd., and its subsidiary, the Rand Mines Power Supply Co. Both companies, which are practically one from an engineering point of view, operate the following stations, all feeding into the same system.

Jan 2, 1916

By Harlan W. Nelson, James B. Purdy

The great majority of stokers used in residential heating installations are of the clinkering type. Because of inherent characteristics of the underfeed combustion process as it occurs in these small stokers, and because of the wide range of operating conditions encountered in residential heating schedules, not all bituminous coals can be used successfully in residential underfeed units. The problem of providing consumer satisfaction has been attacked by the joint efforts of the stoker manufacturers and the coal industry; the stoker manufacturers have been concerned with improving their product to permit the use of a wider range of coals, and coal operators have made every effort to market selected and better prepared coals. In view of the wide range of physical characteristics and chemical properties of bituminous coals, the problems are real and are receiving increased attention. Some twelve years ago a laboratory method was developed at Battelle Memorial Institute for the relative evaluation of coals for use in residential underfeed stokers. The method was developed in conjunction with work being done at that time for Bituminous Coal Research, Inc., and for individual coal producers, to obtain information on the characteristics of coal that determined the successful performance of the small stoker. Details of the equipment and test procedure were given by R. A. Sherman1 in a paper presented at the University of Illinois Fifth Short Course in Coal Utilization. During the past several years, the evaluation of over forty different coals has been determined by investigations sponsored at Battelle by coal operators in the eastern producing districts. The purpose of this paper is to compare the results and conclusions derived from the various tests with marketing experiences of the operators, and to discuss briefly the relationship of test results to standard laboratory determinations. Equipment Used in Tests Fig 1 shows schematically the equipment used in the evaluation tests. The stoker is a commercial model of conventional design, having a nominal feed rate of 30 Ib per hr. A special laboratory furnace is used, which is tightly sealed to prevent the entrance of secondary air. The complete stoker-furnace assembly is mounted on platform scales which permits the measurement of combustible weight losses occurring during the test. The furnace stack, in which are a thermocouple, flue-gas sampling tube, and smoke meter, is connected to the laboratory exhaust breeching through a friction-less connection. Through use of an auxiliary blower system, provision is made for the measurement of the air delivered by the stoker fan to the windbox. A water seal in the duct work eliminates inter-

Jan 1, 1950

By R. R. Spencer, C. A. Campbell, R. J. Marcotte, A. S. Kromer, P. H. Ostlender

Calumet Div. of Calumet & Hecla Inc. is engaged primarily in mining, milling, and smelting the native copper ores of northern Michigan. The copper occurs in fragmental tops of lava flows and in certain interbedded felsitic conglomerates of Pre- Cambrian age. The most famous native copper ore- body in world history is the Calumet conglomerate, which outcrops between the villages of Calumet and Laurium for a distance of about 2 miles. The Osceola lode parallels the conglomerate lode and is mineralized for about 3 miles. Horizontal distance between the two is 750 ft. In 1932 the price of copper dropped to 54 per lb. Coupled with the high cost of obtaining copper from extreme depths, this low price made the venture un- profitable, and the mining unit was abandoned. After the shaft pillar copper was removed from several of the conglomerate shafts in a retreating operation, the mine was allowed to fill with water. In post-depression years, when the price of copper stabilized at about 12¢, Calumet Div. found it profitable to operate its remaining mines on other lodes, as well as its tailings reclamation plants.

Apr 1, 1956

By Edward Wisser

THE Pachuca silver district, situated about 100 kilometers northeast of Mexico City (Fig. 1), covers roughly the southeastern half of the Sierra de Pachuca. The latter is a mountain range with northwest trend, and forms a part of the northeastern rim of the topographic basin known FIG. 1.-LOCATION OF PACHUCA DISTRICT AND OTHER MINING CAMPS. as the Valley of Mexico. The length of the Sierra proper is about 50 km., its greatest width about 9 km., and it rises to a maximum of 600 meters above the general level of the basin floor. The Pachuca district consists of two contiguous subdistricts, the Pachuca area and the Real del Monte area. The center of the Real del

Jan 1, 1936

By John Lamont, Walter Crafts

The principle formulated by Grossmannl for calculating hardenability of steel by multiplying the ideal diameter of "pure" iron-carbon alloys by factors for grain size and alloying elements has been confirmed on many steels and has proved useful in designing substitute alloy steels. Grossmann found that the typical behavior of the multiplying factors was to increase directly in proportion to the amount of the alloy present in a steel. However, the multiplying factor for the effect of silicon on hardenability was found by Grossmann to increase to a lesser degree as the amount of silicon was increased. In view of the increasing use of silicon in heat-treating steels, the effect of silicon on hardenability is becoming more important. Calculation of the hardenability of high-silicon steels made at the Union Carbide and Carbon Research Laboratories, Inc., indicated that the multiplying factor for silicon increased directly in proportion to the amount of silicon present. A more extended study of high-silicon steels covering fairly wide ranges of grain size, carbon, manganese, and aluminum has confirmed that up to 2 per cent silicon the multiplying factor is directly proportional to the silicon content. Manganese and aluminum factors have also been! determined. The results of the study offer strong confirmation of the general validity of Grossmann's multiplying principle. Testing Procedure Steels on which the study of the effect of silicon on hardenability was based were made in high-frequency induction furnaces using Armco iron and standard alloying materials. The ingots were forged to bars, and sections were normalized prior to machining Jominy hardenability test specimens. The Jominy test was carried out under standard conditions.2 The depth of hardness penetration for determination of ideal diameter at "half hardness" was taken at the hardness level indicated in Fig. 29 in Grossmann's paper by the solid line for 50 per cent martensite in plain carbon steel. The depth of penetration of hardness on the Jominy specimen was converted to ideal diameter by the relation given in Fig. 28 of Grossmann's paper. Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Aluminum was determined as "acid-soluble aluminum" rather than as total aluminum, as it is probably more representative of the aluminum that is effective as an alloying agent. In addition to the elements nominally present in the steels, analyses were made for residual phosphorus, sulphur, nickel, copper, molybdenum and chromium on one heat of those made with the same materials during the same period. Actual grain size was determined by microscopic examination of small samples quenched in water after receiving the same thermal cycle as the Jominy hardenability specimens. Chemical analyses, heat-treatment, grain size, and hardenability are shown in Table I representing three ranges of composition.

Jan 1, 1943

By John Lamont, Walter Crafts

The principle formulated by Grossmannl for calculating hardenability of steel by multiplying the ideal diameter of "pure" iron-carbon alloys by factors for grain size and alloying elements has been confirmed on many steels and has proved useful in designing substitute alloy steels. Grossmann found that the typical behavior of the multiplying factors was to increase directly in proportion to the amount of the alloy present in a steel. However, the multiplying factor for the effect of silicon on hardenability was found by Grossmann to increase to a lesser degree as the amount of silicon was increased. In view of the increasing use of silicon in heat-treating steels, the effect of silicon on hardenability is becoming more important. Calculation of the hardenability of high-silicon steels made at the Union Carbide and Carbon Research Laboratories, Inc., indicated that the multiplying factor for silicon increased directly in proportion to the amount of silicon present. A more extended study of high-silicon steels covering fairly wide ranges of grain size, carbon, manganese, and aluminum has confirmed that up to 2 per cent silicon the multiplying factor is directly proportional to the silicon content. Manganese and aluminum factors have also been! determined. The results of the study offer strong confirmation of the general validity of Grossmann's multiplying principle. Testing Procedure Steels on which the study of the effect of silicon on hardenability was based were made in high-frequency induction furnaces using Armco iron and standard alloying materials. The ingots were forged to bars, and sections were normalized prior to machining Jominy hardenability test specimens. The Jominy test was carried out under standard conditions.2 The depth of hardness penetration for determination of ideal diameter at "half hardness" was taken at the hardness level indicated in Fig. 29 in Grossmann's paper by the solid line for 50 per cent martensite in plain carbon steel. The depth of penetration of hardness on the Jominy specimen was converted to ideal diameter by the relation given in Fig. 28 of Grossmann's paper. Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Aluminum was determined as "acid-soluble aluminum" rather than as total aluminum, as it is probably more representative of the aluminum that is effective as an alloying agent. In addition to the elements nominally present in the steels, analyses were made for residual phosphorus, sulphur, nickel, copper, molybdenum and chromium on one heat of those made with the same materials during the same period. Actual grain size was determined by microscopic examination of small samples quenched in water after receiving the same thermal cycle as the Jominy hardenability specimens. Chemical analyses, heat-treatment, grain size, and hardenability are shown in Table I representing three ranges of composition.

Jan 1, 1943

Records of coal in Colorado begin only a few years before the Civil War. In 1859 Macomb reported beds of lignite on both sides of Galisteo Creek, and in the foothills of the Placer Mountains, a place where an outburst and overflow-of trap had changed the lignite into bright, hard anthracite.1 The Union Pacific Railroad sent Joseph T. Hodge to investigate the coal deposits in the Rocky Mountains, close to the projected line, in the fall of 1863. He was told of coal on South Boulder and Rock Creeks, and that somewhere on Lodge Pole Creek it was being worked for supplying fuel for stage stations; a bed was also reported seven miles north of the stage road between Laporte and Latham. It was only in the vicinity of Denver that coal mines were being worked to any extent; these openings were on Coal Creek about 22 miles north of the town, said to have been opened in. 1860. The coal was used by the smiths with ,difficulty and slacked badly on exposure., Some coke was made from one of the seams, the coke being preferred to the raw coal by smiths. Another district was opened along South Boulder Creek, about two and a half miles from the base of the Rocky Mountains, two mines being worked to supply the Denver market.2 Hayden reported a large bed of coal at Golden in 1861 and of having seen a similar one in 1862 about 65 miles east of Pikes Peak, and in 1866, he saw large beds on Rock Creek 16 to 19 miles from Golden. In 1867 he saw the Belmont or Marshall's mines opened in 1863 on South Boulder Creek, which he said was the finest exhibition of coal in the state. The next one was the Murphy mine, on Ralston Creek, five miles north of Golden. A mine was also being worked near Canon City at that time.3 The coal at Golden was being worked in 1864.4 In 1867 the coal mined at Golden was being used in a firebrick' works. At Canon City and other places on the waters of Arkansas River, coal was being mined for use in the valley towns, bringing $5.00 per ton at the mines.5

Jan 1, 1942

By James H. Courtright, Kenyon Richard

SILVER Bell is situated 35 airline miles northwest of Tucson, Ariz., in a small, rugged range rising above the extensive alluvial plains of this desert region. Its geographical relation to other porphyry copper deposits of the Southwest is shown on the inset map in the lower left corner of Fig. 1. The climate is semi-arid. Altitudes range within 2000 and 4000 ft. Opening of the Boot mine, later known as the Mammoth, in 1865 was the first event of note in the district's history. Oxidized copper ores containing minor silver-lead values were mined from replacement deposits in garnetized limestone and treated in local smelters. Copper production had approached 45 million pounds by 1909 when the disseminated copper possibilities in igneous rocks were recognized. Extensive churn drill exploration carried out during the next three years resulted in partial delineation of two copper sulphide deposits, the Oxide and El Tiro. Although the then submarginal tenor discouraged exploitation of these disseminated deposits, selective mining of orebodies in the sedimentary rocks continued intermittently until 1930, providing a production total of about 100 million pounds of copper. The American Smelting & Refining Co. began exploratory and check drilling in 1948 and subsequently made plans for mining and milling the Oxide and El Tiro orebodies at the rate of 7500 tons per day. Production began in 1954 at a rate of about 18,000 tons of copper annually. Formations ranging in age from Pre-Cambrian to Recent are exposed in the Silver Bell vicinity. The more erosion-resistant of these, Paleozoic limestone and Tertiary volcanics, predominate in the scattered peaks and ridges comprising the Silver Bell mountains. The porphyry copper deposits are located along the southwest flank of these mountains in hydrothermally altered igneous rocks. These are principally intrusives which cut Cretaceous and older sediments and are considered to be components of the Laramide Revolution. For three-fourths of its length the zone of alteration strikes west-northwest, Fig. 1. There now is no single structure that accounts for this alignment. However, indirect evidence suggests that a fault representing a line of profound structural weakness existed in this position prior to the advent of Laramide intrusive activity. This line will be referred to as the major structure. It was obliterated by the Laramide intrusive bodies but exerted a degree of control on their emplacement, as evidenced by their shapes and positions. The influence of fault structures on the shapes of intrusives in other porphyry copper districts has been noted by Butler and Wilson' and by others. As shown on the inset map on Fig. 2, a fault of parallel trend and considerable displacement lies to the north. This fault is now marked by a line of small Laramide intrusive bodies. To the south is a third fault of large displacement. Evidence of its age in relation to the Laramide intrusions and mineralization is not recognized, but its conformance in strike with the other two major faults is significant. These three breaks establish a pronounced trend of regional faulting. They are high-angle, and the southerly one may be reverse, Stratigraphic separations on these faults are of the order of several thousand feet. The local Paleozoic section is about 4000 ft thick. It is composed predominantly of limestone with a basal quartzite member. The Cretaceous section appears to exceed 5000 ft. Conglomerates, red shales, and arkosic sandstones (the youngest) characterize the three principal members. Intrusion of alaskite marked the beginning of Laramide igneous activity. It was emplaced as an elongate stock with one side closely conforming to the major structure line throughout a distance of nearly 4 miles. The alaskite was at one time regarded as a thrust block of pre-Cambrian rock'; however, its intrusive relationship and consequent post-Paleozoic age has been established by inclusions of limestone found in outcrops north of El Tiro. The next event was the intrusion of a large stock of dacite porphyry into Paleozoic sediments and alaskite. The stock was some 3 miles wide and at least 6 miles long in a northwesterly direction. It was sharply confined along its southwest side by the major structure line. A number of large pendants of moderately folded Paleozoic sediments occur within and along its southwest edge. Thus the inferred, original major fault between Paleozoic and Cretaceous sediments became a contact between alaskite and Paleozoic sediments and then a contact between dacite porphyry and alaskite. Andesite porphyry may have been intruded later than the dacite porphyry, but relationships are not clear; it may be simply a facies of the latter. The intrusive activity was at this stage interrupted by an interval of erosion. The erosion surface probably was rugged, as there were local accumulations of coarse, angular conglomerate. Subsequently a series of volcanic flows and pyroclastics several thousand feet thick was deposited. A similar unconformity has been recognized elsewhere in the Southwest, particularly in the Patagonia Mountains near the Flux mine some 75 miles southeasterly. Here, as at Silver Bell, volcanics were deposited on an erosion surface cut in Cretaceous and older sediments which had been intruded by alaskite. Though no evidence is offered that closely defines the age of this unconformity, and proper analysis of the problem is beyond the scope of this paper, it is

Jan 1, 1955

By John Chipman, Eric R. Jette, O. B. Ellis

IN the study of the chemical reactions occurring in the open-hearth furnace, it is frequently assumed that a condition of equilibrium between slag and metal is attained. In order to test this assumption it is necessary to have dependable operating data as well as an exact knowledge of the equilibrium state. Considerable progress has already been made in the study of slag-metal equilibria, notably in the earlier work of Herty1 and of Oberhoffer and Schenck2 and in the more recent researches of Krings and Schackmann3 and of Koerber and Oelsen.4 None of these investigators, however, have employed basic slags comparable to those encountered in basic open-hearth practice, so that up to the present time our only information regarding the equilibria of these slags is based upon observations drawn from steelmaking practice in which there is little assurance that actual equilibrium was attained. The original plan of this investigation was to secure simultaneous slag and metal samples at intervals during the making of an open-hearth heat, recording the heat history in detail and obtaining complete analyses of slag and metal, then to bring these slag samples into equilibrium with liquid iron in the laboratory induction furnace and thus to determine directly whether or not the observed relationships in the open hearth represent conditions approaching equilibrium. This plan was only partly successful. While slags were obtained from the open hearth under satisfactorily recorded conditions and these were remelted in the laboratory under equilibrium conditions, changes in slag composition, which accompanied the remelting operation, were so great that the final slag from the induction furnace bore little resemblance to its open-hearth parent and the direct comparison was therefore abandoned. The results, however, lie within a range of slag composition that is of interest in the making of low-carbon steel. As far as we are aware, they represent the first published laboratory study of equilibria involving slags that contain all the constituents of basic open-hearth slag. EXPERIMENTAL HEATS The first set of measurements on slagmetal equilibrium was made in the Research Laboratories of the American Rolling Mill Co. at Middletown, Ohio. This will be known as series A. The second set was made in the Metallurgical Research Laboratories at Massachusetts Institute of Technology, and will be referred to as series B. Series A.-The induction furnace used has been described.5 Approximately I kg. of a special ingot iron containing less than

Jan 1, 1941

By W. D. Klopp, R. I. Jaffee, H. R. Ogden, D. J. Maykuth

The purification of commercial-purity tantalum powder by vacuum sintering in the temperature range 2600° to 2860°C has been investigated. Mixtures of tantalum oxide and tantalum carbide were sintered at 1800° and 2200°C. Tantalum bars containing 1 pct additions of oxygen, nitrogen, and carbon. were sintered in the range 1800° to 2600°C. Anulyses were conducted on the sititeyed mixtures to determine the extent of removal of oxygen, nitrogen, and carbon at each sintering condition. The mechanism for remova1 of each impurity, and the conditions necessary for preparing ductile tantalum by vacuum sintering are discussed. INTEREST in the refractory metals has been stimulated in recent years by the need for structural materials capable of operating at temperatures of 1100°C and higher. These metals include columbium (niobium) (mp 2468°C), molybdenum (mp 2620°C), tantalum (mp 2996°C), rhenium (mp 3160°C), and tung- sten (mp 3415°C). In addition to its high melting point, tantalum possesses the advantages of forming a solid, nonvolatile oxide at temperatures of interest and of being ductile and easy to fabricate. The classic method of consolidating tantalum from powder refined from the ores is by vacuum sintering at temperatures on the order of 2600°C. This sintering treatment both densifies the compacted powder bars and purifies the metal by causing impurities to boil out. The present work was undertaken to provide more quantative data on the relationship between sintering conditions and purity and to determine the mechanisms of impurity removal.

Jan 1, 1961

By H. A. Wriedt

Zinc-vapor pressures in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C were measured by an isopiestic method. Thermody-na?nic properties of zinc in these solutions were derived directly and those of iron with a Gibbs-Duhem integration. Zirzc and iron exhibit large, positive, and moderately temperature-sensitive deviations from ideality. Excess enthalpies and Gibbs energies are positive in the ranges studied. It has been establzshed in relating published phase equilibria to the Gibbs energies of forming solid solutions that positive departures from ideality also exist in the fcc solutions. Tlze stability, as defined by Darken, of the bcc solutions is small but positive at 703.5"C. Its decrease with decreasing temperature indicates that a miscibility gap may exist in the stable or metastable bcc solutions at lower temperatures. The changes of thertnodynanlic properties relatable to changes in magnetic state are minor compared to other changes due to alloying. The accuracy with which the relation between lattice parameter and composition of the bcc solutions is known has been improved. Zinc increases the lattice parameter of a iron by O.ZOZA per unit atom action zinc to at least NZn = 0.25. TO our knowledge, only Ciganl has previously investigated thermodynamic properties of the bcc solutions of the Fe-Zn system. He measured zinc-vapor pressures in the temperature range from about 320" to 360°C by an effusion technique. We have measured the vapor pressures of zinc in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C by an isopiestic technique. This investigation and the pursuant thermodynamic computations are part of a program for studying several properties of these solid solutions. In the appendix we report a remeasurement of the relation at room temperature between the lattice parameter and zinc content. Related work not reported herein embraces measuring the diffusivity2 of zinc in ferrite at 700" to 900°C and the Curie point temperature3 as functions of composition. EXPERIMENTAL METHOD AND APPARATUS Purified iron at a series of constant temperatures was saturated with zinc at a series of constant zinc-vapor pressures, the range of conditions being so limited that the equilibrated solid solutions were ferri-tic. The equilibration was conducted in long capsules, Fig. 1, that had been evacuated, gettered with titanium, and sealed. The purified iron, part of a vacuum-melted ingot of electrolytic-iron stock (Glidden Co. 1044-grade), had the impurity contents listed in Table I. It was used in the form of millings about 0.001 in. thick. A zinc of 99.999 pct purity (United Mineral and Chemical Corp.) and later one of 99.9999 pct purity (Cominco Products, Inc.) were used, with no observed difference in results. Sufficient zinc was placed in the capsule (separate from the iron and kept at a different temperature) to supply the vapor phase and the iron alloy, while leaving a pool of pure liquid zinc throughout the run. The imposed temperature of the residual zinc pool fixed the vapor pressure of zinc throughout the capsule; condensation was avoided at other locations by making this the lowest temperature in the capsule. Two common complications of nonisothermal systems were, we believe, effectively absent from ours: first, molecular species other than monatomic have no appreciable concentration in zinc vapor at 700" to 900~~: second, the development of zinc-pressure differentials in the capsules was suppressed by use of relatively large-diameter tubing and the absence of diluents in the zinc vapor other than desorbed impurities. The specimens and zinc pool were located at two isothermal zones (each ranging within 1°C over several inches) of a wire-wound, 37-in.-long vertical-tube furnace. The required temperature distribution was achieved by external adjustment of the currents in three electrically isolated windings. The temperatures of the isothermal zones were controlled independently by ther-

Jan 1, 1968

By F. Selig, A. S. Odeh

A second-order approximation to the exact solution of the diffusivity equation corresponding to the pressure build-up of a well producing at a variable rate is derived. This approximation is applicable when the well's shut-in time is larger than the total time elapsed since the well was first produced. The resulting equations are compact in form and easy to use. Thus, the need for Horner's' theoretically precise but rather laborious solution to the above problem is eliminated. In addition, these equations apply where the use of Horner's widely known approximate method is questionable. From a practical point of view, the reported method is best suited for analysis of drill-stem tests and short production tests conducted on new wells. INTRODUCTION The utility of drill-stem and short production tests in reservoir studies has long been recognized by the reservoir engineer. If interpreted correctly they could lead to a wealth of information upon which may depend the success or failure of reservoirs' analyses. Initial reservoir pressure and the average flow capacity are two quantities that are normally sought from a drill-stem and/or a short production test analysis. Pressures are the most valuable and useful data in reservoir engineering. Directly or indirectly, they enter into all phases of reservoir engineering calculations. Therefore, their accurate determination is of utmost importance. The flow capacity kh of the reservoir is indicative of its commercial capability. In addition, it can indicate the presence of a darnaged zone around the wellbore and, thus, the necessity for remedial measures. Of the several methods used to analyze drill-stem and short production tests, Horner's' method is by and large the most common. It applies to an infinite reservoir and or a limited reservoir where the effect of production has not been felt by the boundary. Horner's method makes use of the so-called "point-source" solution of the diffusivity equation. The point-source solution is approximated by a logarithmic function and the superposition theorem is utilized to give the familiar pressure build-up equation where is the shut-in time, q is in reservoir barrels per day and the rest of the symbols conform with AIME nomenclature. Eq. 1 was derived for a well which produced at a constant rate q from time zero to time t and was then shut in. In actuality, such a constant rate of production does not normally obtain. Therefore, a correction must be applied to Eq. 1 to account for the varying rates of production. Horner suggested two methods. The first, which results in a theoretically accurate solution, is rather lengthy and laborious and, thus, it is not suited for routine analysis. The second which has been termed a "good working approximation" is the one used by the majority of the reservoir engineers. In the second method, Eq. 1 is modified by simply introducing a corrected time t, and writing where q is the last established production rate prior to shut-in, and t, is obtained by dividing the total cumulative production by the last established rate. Horner's original paper does not give any indication that this method of correction is based on any theoretical justification. In addition, there is a question as to what constitutes the last established rate. In case of a drill-stem test some engineers use the average rate obtained by dividing the total fluid produced by the total flow time, while others calculate the average rate by dividing the total fluid produced by the last flow-period time. Obviously, different results obtain for the different flow rates used. Because of this, a simple method to the varying-rate case was developed which is theoretically sound and which defines clearly the flow rate and its associated time to be used in the calculations. The final equation arrived at is where q* and t* are a modified rate and time, respectively, and can be easily calculated. In addition, it is shown theoretically that Horner's approximate method, if used for a variable-rate case, gives the correct pressure but would not be expected to give the correct flow capacity. MATHEMATICAL ANALYSIS The general equation governing the flow of slightly compressible fluid in porous media may be written as The elementary solution to Eq. 4, representing an instantaneous withdrawal of Q units volume of fluid at the origin at t = 0, is known as the instantaneous sink