Search Documents

By R. W. Gurry

In a series of charts this paper presents the composition of all gas mixtures, composed of the elements carbon, hydrogen, oxygen and nitrogen, which at temperatures from 1000° to 1800°F are in equilibrium with (1) austenite of various carbon contents, (2) iron and iron carbide, (3) graphite, (4) iron and its oxide. THIS paper presents the results of calculations made to determine the proportions of CO, CO2, CH4, H2, H2O and N2 in gas mixtures which, at temperatures from 1000" to 1800°F, satisfy, individually, the following conditions: (1) equilibrium with carbon steel of specified carbon content throughout the stable 7 iron region; (2) equilibrium with iron and iron carbide, both above and below the eutectoid temperature; (3) equilibrium with graphite; (4) equilibrium with iron and its oxide. From these data a new type of chart has been prepared which permits one to determine, from a room-temperature analysis of the furnace gas in question, the effect of the gas upon the steel at furnace temperature. Thus a guide is provided as to the carbon content which will result and as to the possibility of oxidation or sooting. All of the atmospheres commonly used in the commercial heat treatment of steel are composed of some or all of the simple constituents CO, CO2, CH4, H2, H2O and N2, and also in some cases oxygen or higher hydrocarbons. As the gas mixture is heated certain alterations in the proportions of the constituents take place, and at the temperature of the furnace the composition is, in general, not at all that of the entering gas. If equilibrium in the gas phase is presumed a calculation involving the use of certain fundamental data predicts for a certain temperature the carburizing, decarburizing, or sooting characteristics of a given atmosphere, and, upon the additional assumption of equilibrium between gas and metal, also the oxidizing ability of the gas and the ultimate carbon content of the steel. The extent to which these predictions are fulfilled will depend upon how closely the assumptions of equilibrium are realized in any particular case. Although at lower temperatures equilibrium is often not reached, there is considerable evidence indicating that above about 1000°F the approach to equilibrium in the gas phase is generally substantially complete, particularly in the vicinity of the steel which acts as a powerful catalyst in promoting reactions in the gas phase. The extent of the gas-metal reactions is commonly affected essentially by the sojourn at temperature; equilibrium with respect to carbon, for example, is accomplished simply by continuing the treatment long enough. However close the approximation of equilibrium may be in any instance, the above mentioned calculation indicates the condition of the steel at equilibrium, and at the present time this is the only basis of control of a furnace atmosphere. The effect at elevated temperature of a gas of a certain composition at room temperature upon a given steel has customarily been judged by first calculating from gas equilibrium constants the proportions of the gas constituents at the temperature of the steel, then comparing certain of these with the proportions known to be in carbon or oxygen equilibrium. This process is tedious and time-consuming, in particular because the calculation generally involves a series of successive approximations; and since some knowledge and familiarity with this type of computation are required, not everyone needing the information has been, in the past, in a position to obtain it. By making a series of equilibrium calculations, combining with fundamental data for gas-metal reactions, and plotting the results in a special way, a chart has been prepared which enables anyone

Jan 1, 1951

By W. C. Hagel, H. J. Beattie

Seven austenitic alloys of varions base compositions and minor-alloy additions were solution-treated, aged systematically between 1200oand 1800oF, and examined by X-ray and electron metallography. Intragranular preczpitations of µ, Laves, s, ?', Ni3Ti, and x phases were observed as a function of composition and aging time and temperatwre. Phase solubility limits were detevtnitzed within 100Fo intervals. These inter metallic compounds fall into two distinct general classes, and whichever class predomznates depends on base composition. It has become increasingly evident that multicom-ponent austenitic alloys are well characterized by their precipitation processes. Since certain groups of elements act as one, the relationships among these processes are reasonably simple; complete identification of such processes is usually attainable by a systematic aging study with a combination of techniques centered on microscopy and diffraction. Several nickel- and cobalt-base alloys illustrating cellular precipitation and its interaction with general precipitation were reported previously.1 The group of alloys covered in the present paper demonstrates precipitation-hardening reactions involving two distinct classes of intermetallic compounds where the predominating class appears to depend on base composition. This dependency ties in with a crystal-chemistry regularity first observed some twenty years ago by Laves and Wallbaum but never amplified to our knowledge. Results of electron-microscope and X-ray diffraction studies on systematically aged hot-rolled alloys known commercially as S-816, S-590, Rene-41, Incoloy-901, M-308, and M-647 are reported here. Some of these alloys have previously undergone minor-phase analyses by other investiators. Alloy S-816 was investigated by Rosenbaum, Lane and Grant,3 and Weeton and Signorelli.4 Rosenbaum found only CbC in hot-rolled bars. Lane and Grant found CbC and a small amount of M6C in the cast structure and stated that both carbides form during aging, most of the precipitation being CbC. Weeton and Signorelli found CbC, M23C6 and a weak indication of a phase after a slow step-down cooling cycle from 2250°F. Rosenbaum also investigated hot-rolled samples of S-590 and identified CbC and M6C. Preliminary information on Rene-41, gained partly from the present work, was reported by Morris.5 Long-time precipitation phenomena in Incoloy-901 at 1350°Fwere investigated by Clark and Iwanski.B heir raw data re- semble those of our present heat with 0.1 pct B, while their interpretation of these data resembles our interpretation of data from another heat with only 0.001 pct B; they made no statement as to boron content. No previous minor-phase studies of alloys M-308 or M-647 have been reported. EXPERIMENTAL METHODS Table I gives alloy compositions in both weight and atomic percent. Specimens were solution-treated from 1700º to 2200ºF, aged at logarithmic-time intervals up to 1000 hours between 1200 and 1800 F, and examined in accordance with procedures previously described in detail. ' ' Phase extractions were carried out in electrolytic cells containing 800 ml of either 7 pct HC1 in denatured ethanol or 20 pct H3PO4 in water. After electrolysis for 48 hr at 0.1 to 0.2 amp per sq inch, residues were separated by filtration or centrifuging. X-ray powder patterns of residues were recorded on a diffractometer for accuracy and on film for sensitivity. Lattice parameters were calculated by least-squares analyses of indexed sin 8 values, and relative abundances were estimated from intensities of strongest lines of each phase. These phase abundances denote relative amounts with respect to each other rather than to the alloy. Mechanically polished specimens were etched in a freshly mixed solution of 92 pct HC1, 5 pct H2SO4, and 3 pct HNO3. Parlodion replicas for the electron microscope were chromium-shadowed in high vacuum at a glancing angle of 20deg. All electron micrographs are reproduced here with the shadowing source above. The correspondence betweenelectronmicrostructures and phases identified by X-rays was established by a high redundancy of correlation between relative amounts at different stages of aging and examination above and below critical transformation or solubility temperatures. EXPERIMENTAL RESULTS S-816 and S-590—The phases found in S-816 and S-590 after various aging and solutioning treatments are listed in Table 11. These data and the observed

Jan 1, 1962

By AIME AIME

SECOND only to the February Annual Meeting of the Institute are the Regional and Divisional meetings held in the fall of each year. Six such gatherings are scheduled in the next the months, with something likely to interest every member of the Institute. A brief résumé of the programs follows. Regional Meeting Vancouver T HE regional meeting of the Institute will be held at Vancouver, Sept. 13 to 20, in conjunction with the annual western meeting of the Canadian Institute of Mining and Metallurgy. The pro gram appeared on page 350 of MINING AND METALLURGY for July and-proof of careful preparation-a month later re- quires no correction and little elaboration. On the technical side there are few changes. A new item on the Wednesday morning program is the paper, "Investigation of Residential-type Stokers," by H. F. Yancey, supervising engineer, Northwest Experiment Station. U. S. Bureau of Mines, Seattle. As to entertainment the meeting is taking on some most pleasurable aspects. Two notable excursions have been arranged.

Jan 1, 1937

By C. D. Thompson, D. C. Violetta, C. A. Czako

The mechanics of the continuous sintering process are briefly reviewed and the application of this process for the beneficiation of principal minerals used in making cement is shown. Pilot plant tests using pyrobeneficiation techniques were conducted with mixtures of limestone and shale in various ratios. Results are illustrated and show the percentage removal of carbon, carbonates, sulfur, alkalies, and volatiles as a function of the limestone-shale ratio. Tests with varying quantities of solid fwls, added to mixtures containing limestone and shale in a 4 to 1 ratio, were made to attain optimum elimination of the volatile constituents. Experimental results show that 90 pct of these constituents were removed during the calcination sintem'ng process. The advantages of using the beneficiated material for making cement are discussed with regard to prepam'ng, handling, and clinkering operations. A sintering process for treating raw materials or kiln waste products which contain high amounts of alkaline materials is described. Tests were performed with a high alkaline waste dust mixed in a 1 to 1 ratio with raw cement meal. The data from these tests and others using different halides for aiding alkali removal are evaluated by the alkali content of the cement clinker. Test results showed that the Dwight-Lloyd process could be applied with facility in beneficiating raw materials for cement making. Substantial quantities of deleterious volutile constituents were removed by calcining and sintering techniques. The continuous sintering process has been applied for a number of years as a means of beneficiating minerals for subsequent conversion to merchantable products. The process was developed and first used for nonferrous metallurgical applicatfons. However, it has risen to prominence for ferrous metallurgical applications where last year in the U.S. and Canada nearly 40 million tons of iron ore were treated by grate firing processes. Through the years of process development many investigators have realized the versatility of the sintering process and have directed experiments toward the use of it for applications with nonmetallic minerals. These have included calcining limestone, carbonizing coal, expanding shale, and burning cement raw meal. Today commercial sintering plants produce cement clinker from mixtures of limestone and shale, lightweight aggregate from shale or clay, and calcined products from phosphate shale. The mechanics of the downdraft sintering process have been presented by many authors. In general practice the materials to be agglomated are mixed as moistened fines with a solid fuel and this mixture is spread uniformly on the grates of the sintering machine. The charge is then momentarily directed under an ignition furnace. After ignition a continuous downdraft of air promotes combustion of the fuel and through heat transfer particles become partially fused into a coherent mass. This is cooled from continued draft induced after combustion. Many investigators have shown that distinct zones are formed during the process of sintering iron ores. At the midway point of the sintering process these are prominent and are, respectively, from the top of the bed to the bottom, comprised of a cooling zone of sintered material, a combustion zone of sinter formation, a calcination zone, a drying zone, and a zone of unreacted materials. Completion of sintering occurs near the discharge end of the machine where the firing zone approaches either the grates or grate dressing material called hearth layer. Here the peak draft temperature usually can be noted in the windboxes. The zonal pattern has been illustrated with the use of graphs which show thermal gradients as they progress through the bed of materials during sintering. Fig. 1 shows, in simplified form, thermal gradients existing when clinkering cement on a sintering machine. The thermal gradients illustrated are for periods of initiation, midway and completion of the clinkering process. The occurrence of these zones has importance for the beneficiation of cement raw materials. A research program was performed at the Dwight-

Jan 1, 1961

H. H. Bleakney (Dept. of Mines and Technical Surveys, Ottawa, Canada)— The work of Dr. Machlin and his colleagues at Columbia University is so scholarly that one hesitates to take issue with them. Nevertheless the writer feels compelled to enter a demurrer to the mechanism of intercrystalline cracking proposed in this paper. The principal obstacle to its acceptance is found in its preoccupation with purely mechanical influences and its disregard for the chemical effect of impurities. The writer believes that the destruction of metallic cohesion by concentration of impurities at the grain boundaries is a necessary and sufficient condition for the development of intercrystalline cracking; and he believes that discussion of the numerous mechanical explanations proposed should wait until some valid objection to the chemical hypothesis has been advanced. It is nearly twenty years since Gillett" drew attention to the possibility that the chemical influence of precipitation might be the cause of intercrystalline cracking. As early as 1935, Greenwood'" remarked that grain-boundary precipitation of impurities in lead appeared to promote intercrystalline cracking. Again in 1939, Scott commented as follows on a paper by Thielemann and Parker:'" "There are at least two familiar phenomena that can influence grain-boundary cohesion: 1) intergranular oxidation; and 2) grain boundary precipitation. An important consideration in this work, therefore, is to determine which, if either, of these factors is responsible for the low values of cohesive strength observed." In 1952. the writer presented evidence," some original and some abstracted, which indicated that in copper, silver, aluminum, lead and iron, intergranular cohesion was a function of the purity of the metal. In 1954 Glen, discussing a paper by Ridley and Tapsell14 indicated his belief in a precipitation mechanism for the intercrystalline embrit-tlement of molybdenum steel and suggested that with an absolutely pure metal it would be almost impossible to obtain an intercrystalline crack. This suggestion has

Jan 1, 1959

By Ian Wark

IN the paper on the development of the flotation process at Broken Hill (Australia) prepared by the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy and published in its Proceedings for 1930 (N. S. 80), it is stated that the concentration of ores by flotation has been established on a commercial basis in Australia since 1904 and that differential flotation was practiced at Broken Hill in 1912. Since then, progress in flotation practice throughout the world has been rapid, and during recent years the knowledge of the reactions between comparatively modern so-called chemical promoters or collecting agents and the mineral surfaces has been broadened by the published accounts off many investigators, particularly those working in American universities. Because of the benefits the Australian mining industry has derived from the flotation process, it was felt that the industry should take some part in the efforts that are being made to extend the knowledge of the principles on which the flotation process is based. Accordingly, early in 1930, three Broken Hill mining companies-the Broken Hill South, the North Broken Hill, and the Zinc Corporation-together with the Electrolytic Zinc Co. of Australasia, Ltd., and the Mount Lyell Mining & Railway Co., established a laboratory in the chemistry department of the University of Melbourne for the purpose of investigating the principles underlying flotation. Subsequently, the Burma Corporation, Ltd., expressed a desire to cooperate. The two authors are directly employed and controlled by these six organizations, and the cost of the investigation is divided equally among them. The research has been carried out under the general direction and in close cooperation with Harry Hey, chief metallurgist for the Electrolytic Zinc Co. of Australasia, Ltd., and the authors desire to place on record their indebtedness to him for his ever willing help and constructive criticism.

Jan 1, 1932

By David W. Brunton

From the old-fashioned " grab-sample " to the modern timing-device, which takes a machine-sample with mathematical precision, there is a wide gap, which was only crossed by many years of toil and unremitting endeavor. Even to-day, notwithstanding the advancement in the art, " grab-sampling " is still practiced—sometimes to afford the unscrupulous mine-promoter a basis for fairy-tales with which to entrap the too-gullible investor, and often by milling and smelting companies to determine the amount of moisture in custom-ores. The latter practice is almost as reprehensible as the former, and it causes more trouble and ill-feeling between seller and buyer than all other factors put together. -NO reputable concern to-day would think of attempting to determine by grab-sampling the amount of gold, silver, lead, or copper contained in an ore, and yet many buyers expect the miner to accept the results of grab-sampling in the determination of the amount of water contained in the ore, forgetting that accurate results are just as necessary here as in the determination of the metals, because the result determines the percentage of weight of the ore which shall be excluded and considered to have no value whatever. Samples for the determination of moisture should be taken with as great care as samples for the determination of metallic content, and in order to avoid the extra expense of a separate operation moisture-samples should be taken from the sample-safe. As the sample reaches the sample-bin in a smaller stream and by a more circuitous route than the " reject" travels in its path to the outgoing car, it loses more moisture en route, and a constant should be added to compensate for this difference. Carefullg ,con ducted experiments have shown that the differ.elice in loss of moisture between the two routes does not exceed 10 per cent. in summer and 7 per cent. in winter. For instance,

Jan 1, 1910

By J. F. Smith

ELASTIC constants of yttrium and eleven of the rare earth elements have been measured. This has been accomplished by measuring the propagation velocities of ultrasonic pulses. The velocity measurements were made by noting the elapsed time between an applied pulse and the appearance of successive echoes. The pulse-echo technique has become relatively common, and the basis of the measurement is outlined in several standard tests, e.g., Heuter and Bolt.1 Two important assumptions are made when using this method for the determination of elastic moduli. First, the pulse is assumed to propagate as a plane wave. To justify this assumption, the cross section of the test specimen should be large compared to the wave length of the transmitted pulse. For these measurements on the rare earth elements the minimum cross section wave length ratio was about 20. A second assumption which must be made when using polycrystalline specimens is that the grains are sufficiently numerous and randomly oriented so that the specimen may be approximated as elasti-cally isotopic. The grain size in the as-cast specimens which were used is believed to be sufficiently fine for this approximation, and the degree of preferred orientation is believed to be small. Supporting this viewpoint is the fact that elasticity measurements by the pulse-echo technique on as-cast specimens of other metals give results which are in satisfactory agreement with values obtained by other techniques. Hence, it is believed that the measured elasticity values for the rare earth elements are not apt to be seriously in error due to the assumption of elastic isotopy. The apparatus used in this determination was a modified Sperry Reflectoscope with a precisely calibrated time base circuit. Piezoelectric transducers were used both to generate the pulse and to detect the echoes. X-cut quartz crystals were used for the longitudinal modes, and Y-cut quartz crystals were used for the shear modes. Frequencies of 2.25 and 5 megacycles per sec were employed. Most of the specimens were 2.5 to 5.0 cm in length. Results Table I is a tabulation of the measured propagation velocities of longitudinal waves and of shear waves, together with densities obtained by Sped- ding, Daane, and Herrmann2 from lattice parameter measurements. The shear modulus, Poisson's ratio, and Young's modulus were calculated from the data in Table I through use of the following relationships: µ = pv32 [1] s=2-(vb/vs)2/2[1-(vb/vs)2] [2] and Y= 2µ(l+s) [3] where s is the shear modulus, Y is the Young's modulus, s is Poisson's ratio, p is the density, V0 is the longitudinal wave velocity, and v, is the shear wave velocity. The calculated quantities are shown in Table 11. Compressibility values can be computed from the relationship and the computed values may be compared with measured values obtained by Bridgman.8 Table III lists the data for such a comparison. The agreement is satisfactory, being particularly good for neodymi- um and gadolinium, poor for samarium, and intermediate for the other elements. Some variation is expected since Bridgman's measurements are isothermal, whereas the present measurements are adiabatic. In addition there may be some effect due to small variations in purity. Though most of the rare earth metals measured by Bridgman and all of the metals used in the present measurements were prepared at this laboratory, minor purity variations might exist since the samples came from different lots. Also, any imperfections such as dislocations, vacancies, voids, grain boundaries, microcracks, etc., should contribute to the volume change of a com-

Jan 1, 1958

By G. S. Cole, G. F. Bolling

A series of Al-Cu alloys has been cast from constant superheat to solidify either with a hot top or with a free liquid/air interface. All the other variables which affect relative fluid motions were kept constant except the imposition of slow rotations m oscillations of the mold. Depending upon the exact circumstances, evi-dence could be found for the nucleation of equiaxed grains from dendrite bits detached from the columnar zone, or from the free surface, or from solid bits induced at pouring; a special experiment showed the solute buildup during ingot solidification and by inference the reality of constitutional supercooling. All methods of grain nucleation are thus supported. When solidification is arranged in a static mold the columnar- to-equiaxed transition occurs by one of these nucleation paths, subject to the natural decay of temperature gradients which promotes nucleation or the survival of nuclei. But when solidification is forced under special fluid flows it may display odd transitions. In one of these the equiaxed zone is synihesized from. dendrite bits detached from the solid/liquid interface. These survive under the concurrent lowering of temperature gradients and eventually cause transition by impeding columnar growth. GRAIN structure control is desired because real experience shows that specific properties are associated with specific cast grain structures. But since control is thus a matter of need and does not require understanding, much of casting remains art. For example, the manipulation of relative fluid motions in simple ingots provides a control of grain structure development,1-4 but theoretical insight is not required in order to broaden its potential applicability. Fortunately, however, once a variable like fluid flow is recognized it can also provide paths toward new insight. New observations using this variable have provided an insight which is curious. All the theories or descriptions of the columnar-to-equiaxed transition (CET) seem to be supported as long as the appropriate experiment is carried out. In order to develop this idea, let us ignore segregation, the chill zone (until a later section of this paper), and the origin and development of the columnar zone.= The details of questioning how equiaxed material forms in a casting may be divided in two. The first part is simply a questioning of the origin for equi-axed grains: are there fresh nuclei from heterogeneous nucleation, or dendrite bits broken off or melted from the columnar zone or elsewhere,6 or other solid bits surviving from the outset of freezing? The second is more complex, a questioning of the CET: does columnar growth slow down and allow the dominance of equiaxed grains, however they are formed, or do equi-axed grains take over and force columnar growth to stop? This "chicken-or-the-egg" second question can be quite useful, especially because it allows us to delineate the ordinary or NATURAL EQUIAXED ZONE and the induced or SYNTHETIC EQUIAXED ZONE. A natural equiaxed zone occurs if solidification proceeds in the absence of disturbances or extraneous forces such as ultrasonics, stirrings, and so forth. Both the CET theory proposed by Winegard and Chal-mers, 7requiring constitutional supercooling, and the CET theory suggested by Chalmers,8 requiring nuclea-tion only on pouring, pertain to the natural equiaxed zone. The best collating evidence to date for both these theories is contained in the work by Biloni and Chal-mers;9,10 the former theory7 is supported by special versions of the unidirectional growth experiment performed by Plaskett and winegardl1 and the latter theory' is supported in detail for the solidification of small ingots. An equiaxed zone can be synthesized when disturbances caused by forced fluid flows2-4 or other artificial means9,10 break off or melt off dendrite tips from an advancing solid/liquid interface,* if (and only if) temperature gradients in the melt are (forcibly) reduced enough to ensure the survival of these bits of dendrites, 2'3 Willful disturbances even so trivial as those produced by rapping a mold might be included here; as will be shown for example, this follows Southin's suggestion that the free liquid/air interface

Jan 1, 1970

By J. F. Haseman, J. E. Davenport

IN the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1-2 results in inadequate beneficiation. INVESTIGATION OF FLOTATION METHODS Flotation has been used in Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate.3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over-all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P205 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P205, 20; Si02, 40; CaO, 29; Fe203, 2; A1203, 3; F, 2.3. The particle-

Jan 1, 1947

By Hon. Tasker Oddie

DURING the closing days of the last Congress a resolution was passed, creating the Senate Com-mission of Gold and Silver Inquiry. The resolu-tion charges the Commission with the responsibility to investigate and report to the Congress on Jan. 1, 1924, upon the following subjects: 1. The causes of the continuing decrease in the production of gold and silver. 2. The causes of the depressed condition of the gold and silver industry in the United States. 3. The production, reduction, refining, transportation, mar-keting, sale, and uses of gold and silver in the United States and elsewhere. 4. The effect of the decreased production of gold and silver upon commerce, industry, exchange, and prices. The personnel of the Commission is as follows: Senators Pittman, Sterling, Goodling, Walsh and Oddie. At a meeting on May 8, H. N. Lawrie, a mining engi-neer and economist, was appointed as Assistant to the Commission. The present situation with respect to the gold and silver mining industries is well illustrated by the follow-ing data: The total world production of gold (in dollars) for 1915 was $468,724,918, and for 1921, $329,915,101; as shown by the reports of the U. S. Mint; and for the year 1922, $306,793,000, which is based oh a prelimi-nary estimate; this indicates a decrease of 34.5 per cent. between 1915 and 1922. The total world production of silver (in fine ounces) for 1915 was 178,850,000 oz.; for 1921, 175,268,234 oz., a decrease of 2 per cent.

Jan 6, 1923

Report of the Secretary TO THE BOARD OF DIRECTORS AND THE MEMBERS OF THE AMERICAN INSTI¬TUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN As will be shown by the special reports of the Finance, Membership, Library, Papers and Publications, Increase of Membership, and other standing Committees, together with that of the Treasurer, the year 1927 was one in which the Institute made very satisfactory progress in a number of directions. In total numbers the membership is no larger but in revenue from dues there has been a marked increase. This has been due to the promotion to full membership of Junior Associates of earlier years, to the larger proportion that come in originally as members rather than juniors, and to the keener interest in the work of the Institute reflected in prompter payment of dues. The latter is important, since experience shows that of those who fall behind a large number must ultimately be dropped for non-payment. Conditions in the mining in¬dustries have been healthy though not booming. It has been much easier for members to find employment and meet their financial obligations but there has not been that flow of young men into mining, and hence in part into the Institute, that characterized certain earlier years. Rather the tendency toward centralization and larger industrial units has re¬stricted the number, though not the scope, of opportunities for technical men in the mineral industries. The Institute is constantly receiving resignations from members crowded out of mining into other lines of activity. On the other hand, those who remain in mining and metal¬lurgy have a greatly increased necessity for information and contacts with technology. A few years ago many superintendents and most foremen were non-technical men. Today the reverse rule obtains and shift bosses and men who occupy even lower positions in industrial units are called upon to know and to apply such an amount of technical knowl¬edge that graduate engineers are the rule rather than the exception. The curious situation has obtained that with a much smaller enrollment of students in the schools of mining and metallurgy there has been at times an actual shortage of young engineers for beginners' jobs. The young men retort that the conditions of employment and pay offered in mining are not equal to those in other lines and, while it is undoubtedly true that the young engineer beginning in mining is able to start under conditions markedly better as to pay, living, and responsibility than did the men who are now leaders, they are required to know much more and have usually spent more in time and money to qualify for their jobs. The whole matter is one which warrants much more attention than has been given to it. For the Institute it is important since the young men

Jan 1, 1923

By J. M. Sands

THE state of Kansas had a daily average crude-oil production of about 87,000 bbl. at the beginning of the year. This showed a steady but consistent decline during the 12 months, so that the daily average production at the end of the year was slightly over 68,000 barrels. GREENWOOD COUNTY THE most active development in Kansas during the year was in Greenwood County, in a line from near Sallyards in T 25-R 9 to east of Madison in T 22-R 11. The main part of this development has been in a succession of pools beginning at the south with the Polhamus pool in 34-24-9 and 3 and 4-25-9; Thrall pool in 28, 29, 32 and 33-23-10; Burkett pool in 13, 23, 24 and 26-23-10; Seeley and Wick pool in 22, 27, 28,. 32 and 33-22-11 and 5, 6, 7, and 8-23-11; Frohm pool in 11, 14 and 15-22-11; Madison pool in 31 and 32-21-12 and 6, 22, 12 and 1-22-11. Some of these pools have two or more sands, locally called Bartlesville and Burgess Sands. They range in depth from 1850 ft. near Madison to 2450 ft. near Sallyards, the general dip being to' the west. The thickness of these sands run from 20 to 100 ft., the initial production of the wells being 50 to 1000 bbl of 40-gravity oil or better.

Jan 3, 1924

By George B. Langford

ON THE QUESTION of postwar controls there are today three schools of though ; some advocate state control of everything the socialists ; second are those who advocate the removal of all governmental control over industry - the freedom of enterprise ideal ; and third are those who advocate a middle course - sufficient control to stabilize economic and industrial life, and to prevent violent fluctuations such as we saw in the interwar years. I advocate this third course. I firmly believe un free enterprise, but not in freedom of enterprise, or laissez faire, and there is a great and significant difference between these two.

Jan 1, 1944

By Earl Oliver

Dean Roscoe Pound, of Harvard Law School, in addressing the A.I.M.E. Petroleum Division on Feb. 22, 1934, said, "When you are able to work out a program that is mechanically feasible, that is economicaIly advisable, and which seems in your judgment, which is just as good as that of anyone, to be politically wise, you will not have very much trouble in the end in inducing the courts of today to find that it is legally sound." The purpose of this paper is to show: first, legal conditions necessary to promote conservation and stabilization; and second, to suggest operating procedure when those legal conditions are established. The proposal is mechanically feasible and economically advisable. A growing public understanding should make it politically wise. The disappointing progress in the development of conservation and stabilization can be attributed to the lack of two legal concepts as integral parts of oil and gas law; i.e., (1) a practical substitute for the capture rule, (2) collective ownership control for the individual oil and gas pool. When these two concepts are established on an equitable basis, conservation and stabilization procedure will become a comparatively simple process, more or less automatic in its adaptation and operation. Establishing these concepts is the function of the law-making agencies and might well be left to them for discussion except that the mechanical processes that give them form and substance must first be developed by the engineer. A Substitute for the Capture Rule Much has been written on these subjects, but the most concrete statement that has come to the attention of this writer is the following from an article by Charles G. Haglund in the Kentucky Law Journal of May, 1934: The Oxford1 case is not only authority for the proposition that it is competent for the legislature to modify the old property law of capture with respect to oil and gas but that it may also delegate such authority to a subordinate body.

Jan 1, 1935

By H. OSBORG

THE patent literature of alloys for the last two decades or so indicates that the number of liatents referring to smaller and smaller percentages of essential alloying constituents is on the increase, whereas the number of patents relating to considerable percentages of alloying additions becomes smaller. The claims regarding physical properties indicate consistently higher and more rigid values and show the possibility of modifying the physical properties by only slight changes in the percentage of minor constituents or by applying different methods - of treatment. Alloys of the same base have been made suitable for a number of different applications by intelligently and rigid- ly controlling their composition, melting, casting, working, and heat-treatments. Other trends indicated in the development of modern alloys are higher corrosion resistance, higher fatigue limits, and "stability" in volume.

Jan 1, 1937

By JAMES SCULLY

For the last 4 years political leaders have found a new subject on which they can safely generalize wihout creating opposition. That subject is commodity prices. Since the four-fold increase in OPEC crude oil prices, public attention has focussed as never before on the subject of commodity prices. To advocate stabilizing commodity prices is akin to supporting motherhood or peace or better schooling. Everyone gives lip service to the concept that stable commodity prices are desirable. It is easier to state the principle than to achieve it. Prices that are stable in terms of one currency may be clearly unstable in terms of a different currency. This has become a troublesome matter since 1971, when the world's leading trading currencies were set free to float in relation to each other. To illustrate: consider copper prices in the interval between the end of 1974 and the end of 1977. During those 3 years, the copper price in pounds sterling on the London Metal Exchange rose by 25 per cent. During that period, however, in terms of the USA dollar equivalent, the price was unchanged. And during that period, in terms of the German mark equivalent the price shrank by 13 per cent while the Japanese yen equivalent fell by 20 per cent. Thus a price that appears stable in dollars, rose in terms of pounds sterling and fell in terms of marks and yen. Had this result been achieved as a consequence of an international effort to stabilize prices, an American would have said the effort was successful. An Englishman would have said it had failed to prevent a price rise. And a German or a Japanese consumer would have been happy to have covered his copper needs at a lower cost in terms of his own currency.

Jan 1, 1978

By Thomas R. Scotese

A rock mechanics instrumentation and monitoring program was implemented during pillar extraction at Gulf Mineral Resources' Mt. Taylor Mine, the deepest uranium mine in the U.S. Three types of monitoring were employed: (1) drift convergence around stopes (using a portable tube extensometer), (2) stress changes in pillars (using vibrating wire stressmeters in horizontal boreholes), and (3) load changes in haulageways under stopes (using vibrating wire load cells in jack stands). Results include convergence-time graphs, convergence contour maps, stress-time graphs, a stress increase contour map, load-time graphs, and abutment load limit maps. Major factors influencing results include (1) size of pillars around the extraction area, and (2) presence and orientation of a major fault adjacent to one extraction area. These factors, combined with pillar extraction, produced evidence of load transfer over 120 m from a stope measuring only 55 m x 45 m. Vertical stress increases of 7 to 17 MPa (1000 to 2500 psi) within 60 m of the stope were obtained using the stress- meter manufacturer's method. The fault apparently prevented load transfer in the down-dip direction but increased load transfer in the up-dip direction. Convergence rates of up to 1.3 cm/day (0.5 in/day) were measured at two stations. Instruments were generally reliable despite adverse underground conditions. The instrumentation and monitoring program at Mt. Taylor provided a warning system against ground control problems and a characterization of ground behavior for future development and extraction of pillars. Recommendations are made for future mining and instrumentation practices.

Jan 1, 1984

By C. Land, R. Hultgren

Heat contents of four Cr-Ni alloys were determined in a diphenyl ethev calorimeter. Aside from ferromagnetic effects, Kopp's law of additivity of heat capacities is approximately fol-lowed, in disagreement with earlier results of A. W. Foster. In 1934 Foster1 reported heat-capacity measurements of dilute solutions of chromium in nickel, primarily as a study of the effect of alloying on the ferromagnetic Curie temperature. He found that, apart from the Curie temperature effect, the general level of heat capacities was reduced 10 pct by the addition of 1 pct Cr; 20 pct by the addition of 2 pct Cr. His measurements of pure nickel essentially agreed with accepted values. These results indicate that small amounts of dissolved chromium cause an increase in the Debye temperature of nickel, presupposing a change of frequency of interatomic bonding vibrations which is much larger than should be expected. If Foster's results were verified, therefore, they would have important implications for bonding theory. The only other heat-capacity measurements in this system seem to be those of Taylor and Hinton,' who studied anomalies which they attributed to super-lattice formation at 25 at. pct Cr. At temperatures above the anomaly, Taylor and Hinton found heat capacities at this composition were quite normal, approximately obeying Kopp's law of additivity. EXPERIMENTAL WORK In order to verify or disprove the remarkable results of Foster, the heat contents of four dilute solid solutions of chromiunn in nickel were measured in a diphenyl ether calorimeter. This instrument, described elsewhere,, operates on the principle of the Bunsen ice calorimeter, but uses diphenyl ether as the working substance. Diphenyl ether melts at the convenient temperature of 26.S°C and supplies a more sensitive measure of heat than ice. The hot sample, in an atmosphere of argon, is dropped from a furnace at a measured temperature into a chamber which is surrounded by a mixture of solid and liquid diphenyl ether. The heat from the hot specimen melts some of the solid without chang- ing the temperature of the calorimeter. The amount of solid melted, and therefore the number of calories released by the specimen, is measured from the increase of volume of the mixture, which pushes mercury down a graduated capillary tube. The apparatus has been standardized against the known heat content of pure platinum. Heat loss during the dropping of the specimen was estimated by comparing the heat content of an empty platinum capsule with a solid platinum ball of the same radius and degree of polish of the surface. Repeated tests demonstrate the precision of measurement to be closer than *0.3 pct. Smoothed experimental results are listed in Table I. The tabulated values for pure nickel are taken from kelley, several measurements were made which agreed closely with this tabulation. For chromium, however, no similar agreement was found. The values tabulated were taken from a thorough study of chromium with the diphenyl ether calorimeter which will be published elsewhere.= Suitable plots of the data showed the expected ferromagnetic anomalies in the low-chromium alloys, while the 11 pct alloy shows no ferromagnetic anomaly, but a different, small anomaly below 900°K. This is perhaps the same anomaly found in CrNi, which was once attributed to superlattice formation,' but is probably due to some other cause, such as antifer-

Jan 1, 1960

Jan 1, 1901