Search Documents

By V. F. Marsters

Seepages of oil in Ecuador have been known for many years. The locality first to receive attention, and still worked in a modest way, lies on the north shore of the Santa Elena peninsula, between La Puntilla and Salinas. Operations mere first conducted largely by local cdpital. Later, foreign companies acquired large blocks of land, where they have done considerable drilling. For details concerning present drilling activities in Ecuador, we are indebted to Leon Price, an Ame~ican resident engineer of Ecuador. The information solicited came to the author through the office of the American Consulatell with permission to use it. The coastal plain bordering the Province of Tumbes, Peru, continues to the northeast, but narrow on passing the Zarumilla River. From this point northward it widens toward Santa Rosa. In fact, the pampas, as shown on the official Wolf map, correspond fairly well to the areal extent of tbe coastal plain as far as Guayaquil. This is shown in a general way on the accompanying map. The author understands that the Guayaquil enlbayment is bordered on all sides by the coastal plain, as recognized at Tumbes and farther southwest, and that it can be followed without a break as far north as Palmar. This view is supported by the mapped area regarded by Mr. Price as favorable or possible oil territory. Moreover the islands in the Gulf of Guayaquil are the same geologically as the coastal edge, being composed of Tertiary sediments. The author understands also that Tertiary formations occur north of Palmar. According to a report by Mr. Cardon, of Guayaquil, Tertiary sediments are exposed in the region of San Francisco and extend to and beyond Pta. Calera. There is also reason to believe that at least the lower part of the valley of the Santiago River is occupied by Tertiary sediments, ~~hich probably border the const line and extend into the River Mini l)nsin, and into Colombia. On the south coast there are many seepages, most of them near the inner edge of the coastal plain, between Zarumilla and Santa Rosa and also between Santa Rosa and Machala. I11 the latter region are

Jan 1, 1923

By Dart Wantland, C. A. Heiland

There once was a little kid, whose lot was a very tough one until he grew up. His parents did not have much in common; from all indications, it is probable that the child was not wanted. His father Geology and his mother Physics separated shortly after his birth, which occurred during the World War amid a smoke screen of mathematics. He was kicked around a great deal. His parents could not agree on a name, and they finally christened him "Geophysics," for short. His relatives insisted that the name should be "Geophysical Prospecting," "Geophysical Exploration" or "Exploratory Geophysics"; though the youngster has grown up by now, this battle is still going on. His father did not think the child would amount to much until he began to show some unexpected talents, which were acquired, no doubt, from his mother Physics. His progress caused his father no little worry, and he began to wonder whether his offspring would help him in his business when he grew up or would set up shop in competition with the old man. His aunt Petroleum watched his growth with benevolent interest; his uncle Mining remained rather skeptical and cousin Civil Engineering not only assumed the attitude of the man from Missouri but was not much convinced even after he had been shown. Making a long story short, the kid decided that he had to stand on his own feet and get along as best he could. Having come from a good family he possessed some outstanding characteristics such as resourcefulness and a reasonable amount of business ability. He therefore decided that it would be to his advantage to follow in his father's and mother's footsteps as much as possible, and develop the good qualities of both. As a result, the youngster did fairly well for himself, and his relatives decided that it might be to their advantage to be on better terms with him. Father Geology had come to the conclusion that the boy could be very helpful to him and now wanted him to live in his house. His mother, who had brought him through the teething and measles stages, felt quite capable of bringing up the boy without the help of his father; and, as the fairer sex will do, would confide to a neighbor every now and then that his

Jan 1, 1940

By C. A. Heiland, Dart Wantland

There once was a little kid, whose lot was a very tough one until he grew up. His parents did not have much in common; from all indications, it is probable that the child was not wanted. His father Geology and his mother Physics separated shortly after his birth, which occurred during the World War amid a smoke screen of mathematics. He was kicked around a great deal. His parents could not agree on a name, and they finally christened him "Geophysics," for short. His relatives insisted that the name should be "Geophysical Prospecting," "Geophysical Exploration" or "Exploratory Geophysics"; though the youngster has grown up by now, this battle is still going on. His father did not think the child would amount to much until he began to show some unexpected talents, which were acquired, no doubt, from his mother Physics. His progress caused his father no little worry, and he began to wonder whether his offspring would help him in his business when he grew up or would set up shop in competition with the old man. His aunt Petroleum watched his growth with benevolent interest; his uncle Mining remained rather skeptical and cousin Civil Engineering not only assumed the attitude of the man from Missouri but was not much convinced even after he had been shown. Making a long story short, the kid decided that he had to stand on his own feet and get along as best he could. Having come from a good family he possessed some outstanding characteristics such as resourcefulness and a reasonable amount of business ability. He therefore decided that it would be to his advantage to follow in his father's and mother's footsteps as much as possible, and develop the good qualities of both. As a result, the youngster did fairly well for himself, and his relatives decided that it might be to their advantage to be on better terms with him. Father Geology had come to the conclusion that the boy could be very helpful to him and now wanted him to live in his house. His mother, who had brought him through the teething and measles stages, felt quite capable of bringing up the boy without the help of his father; and, as the fairer sex will do, would confide to a neighbor every now and then that his

Jan 1, 1940

By Eugene Guccione

FOREWORD-At the SME-AIME meeting in Las Vegas this year, the SME Publications Board and the MINING ENGINEERING Committee decided that a fitting way of celebrating the United States' bicentennial would be to publish an article in ME covering the great men in American mining. After some discussion as to the inclusion of financiers -men such as William Randolph Hearst, J. Pierpont Morgan, etc.-the group agreed that the feature should be restricted to the "nuts-and-bolt people," e.g., mining engineers, geologists, mineral processing engineers. Thus, from the AIME All Institute Honors roll and from the SME Awards list, the group chose these 11 historical figures: Herbert Hoover, Daniel C. Jackling, Henry Krumb, James Douglas, Rossiter W. Raymond, Hal W. Hardinge, Seeley W. Mudd, Erskine Ramsay, Howard N. Eavenson, Robert A. Richards, Arthur F. Taggart. What follows is an account of each of these great miners' achievements and the problems they faced, and an assessment by some of today's mining leaders of the challenges that lie ahead.

Jan 7, 1976

By Peter B. Nalle

Over a period of years the Crestmore plant of the Riverside Cement Co. has been supplied with limestone from the Chino limestone bed. The limestone bed dips about 40º and extends 1500 ft along the strike. Thickness of the bed is such that horizontal distance from footwall to hanging wall varies from 400 to 1200 ft. When the new room and pillar mining system was instituted the haulage units used for development were model C Tournarockers. Four of these diesel units were purchased with the idea of using them solely for development work since it was realized that they would have to be supplemented by additional, and perhaps larger haulers.

Jan 4, 1959

By V. R. Garfias

With the exception of the United States and Russia, none of the leading world powers have within their boundaries the oil supplies needed to meet present peace-time requirements, and even in regard to the United States it is admitted by competent observers that the known oil reserves within the country are inadequate to meet demands for more than a comparatively few years. It follows, therefore, that the transportation of petroleum—almost entirely by tank steamers—from foreign fields to the main consuming centers is one of the most important factors affecting the present and future development of the oil industry. The world-wide distribution of petroleum is affected by numerous factors of which international politics is not the least important. The assurance of an ample supply of petroleum—one of the most essential munitions of war—is of paramount importance particularly to those countries subjected to the rivalries of powerful neighbors. And paralleling the importance of the control of an ample supply is that of its safe transportation from the fields to the consuming centers. To illustrate: France is dependent almost entirely on foreign sources for its petroleum requirements estimated at close to 100,000 bbl. daily, and in order to control such a supply after the World War it acquired an interest in the Iraq oil fields. Lately it has undertaken the construction of a pipe line from these fields to the Mediterranean seaboard in Syria with the expectation that late in 1934 these fields will supply between 30 and 40 per cent of the country's requirements. It should be noted, however, that the availability of this supply is entirely dependent on the safe operation in the Mediterranean at all times of an adequate fleet of tank steamers. Thus, in order to transport 40,000 bbl. daily, it will be necessary for one 10,000-ton tanker to leave Tripoli, the Syrian port, say for Marseille, every other day throughout the year while to meet the entire present peace requirements of France from the Iraq fields, a fleet of some 30 such tankers must be kept in continuous operation between Tripoli and Marseille.

Jan 1, 1934

By P. D. I. Honeyman

CHANGING trends in concentration, involving regrinding with the subsequent production of a finely divided, high-grade flotation product, presents a real problem to the modern copper smelter. In the treatment of such a material, handling difficulties are numerous and potential possible losses may be very great. In many plants, of course, preliminary roasting of the furnace charge remains an economical necessity. Under such circumstances, the operator has no alternative except to follow orthodox roaster reverberatory practice, though taking all possible precautions to avoid excessive dust losses and bad working conditions. In other plants, roasting is not only unnecessary but would be highly undesirable, and at best the charge would be merely dried before entering the reverberatory furnace. In the latter case the possibilities of raw charging loom large. The Miami plant of the International Smelting Co. handles the entire output of concentrates of the several mining companies operating in the Globe-Miami district. All of these companies produce a flotation concentrate which, at the Miami Copper Co. particularly, is all reground and is high in grade. In addition, the Inspiration Copper Co. ships a substantial tonnage of high-grade cement copper to the smelter from its leaching plant. Following the flow sheet of the original plant, all such material received was bedded, dried in Wedge furnaces and smelted in reverberatory furnaces. At times during the history of the plant it has been necessary to carry the drying operation further, to a partial roast, before reverberatory smelting. Since the charge contained over 80 per cent flotation concentrates, the handling of which in a dried condition was at best a dusty job, unusual precautions were taken to cut down dust losses. The Wedge furnace plant was equipped with a Cottrell treater and all hoppers and calcine cars were carefully designed to cut down dust loss in transferring the so-called calcine from hoppers to car and from car to furnace. In the furnace itself the dusting problem was a severe one. Arch erosion was very rapid and flues and waste-heat boilers rapidly filled up with a partly smelted flue dust.

Jan 1, 1932

Jan 1, 1914

By R. A. Bowen

The Montreal mine, operated by the Montreal Mining Co., is four miles west of Ironwood, Mich., in Iron County, Wisconsin. It is the westernmost producing property on the Gogebic Iron Range of the Lake Superior district. Its production is 4000 tons of hematite per day from an average depth of 2300 ft. This tonnage is hoisted through a five-compartment vertical shaft. Several mining methods are in use but in the larger orebodies the method is sublevel caving. ORE Occurrence and Chaeacteristics The main orebodies of the Montreal mine lie in eastward-pitching troughs formed by the intersections of intrusive dikes with impervious members of the iron formation. The formation has an average width of 425 ft., strikes east and west and dips north at approximately 62. The dikes dip south at 45° and bear north 20' from the strike of the formation, making the intersections with various members pitch east at 16°. The dikes are not continuous across the formation but are interrupted by a longitudinal bedding fault, which has a throw of 380 ft. vertically and 885 ft. horizontally. North of the fault zone the formation is called "hanging," south it is called "footwall" formation. The faulting has created two ore-bearing horizons; viz., at the intersection of banging dikes with the slate members and the foot dikes with the quartzite footwall. In each formation the main ore-bearing member consists of wavy beds of hard chert interlaid with hematite. In the most productive part of the mine, where the sublevel caving method is employed, a hanging-formation dike lies in juxtaposition with a footwall dike and the iron formation carries ore in certain sections from the quartzite footwall to the hanging dike. Here a horizontal section of the orebody may be 300 to 400 ft. wide for a length of 150 ft. or more and tail out lengthwise in both the foot and hanging formations. The footwall ore section is much longer than the hanging wall because of the orebody's greater height above the "pitching dike."

Jan 1, 1940

By R. A. Bowen

The Montreal mine, operated by the Montreal Mining Co., is four miles west of Ironwood, Mich., in Iron County, Wisconsin. It is the westernmost producing property on the Gogebic Iron Range of the Lake Superior district. Its production is 4000 tons of hematite per day from an average depth of 2300 ft. This tonnage is hoisted through a five-compartment vertical shaft. Several mining methods are in use but in the larger orebodies the method is sublevel caving. ORE Occurrence and Chaeacteristics The main orebodies of the Montreal mine lie in eastward-pitching troughs formed by the intersections of intrusive dikes with impervious members of the iron formation. The formation has an average width of 425 ft., strikes east and west and dips north at approximately 62. The dikes dip south at 45° and bear north 20' from the strike of the formation, making the intersections with various members pitch east at 16°. The dikes are not continuous across the formation but are interrupted by a longitudinal bedding fault, which has a throw of 380 ft. vertically and 885 ft. horizontally. North of the fault zone the formation is called "hanging," south it is called "footwall" formation. The faulting has created two ore-bearing horizons; viz., at the intersection of banging dikes with the slate members and the foot dikes with the quartzite footwall. In each formation the main ore-bearing member consists of wavy beds of hard chert interlaid with hematite. In the most productive part of the mine, where the sublevel caving method is employed, a hanging-formation dike lies in juxtaposition with a footwall dike and the iron formation carries ore in certain sections from the quartzite footwall to the hanging dike. Here a horizontal section of the orebody may be 300 to 400 ft. wide for a length of 150 ft. or more and tail out lengthwise in both the foot and hanging formations. The footwall ore section is much longer than the hanging wall because of the orebody's greater height above the "pitching dike."

Jan 1, 1940

By Jonathan S. Jackson, Bruce P. Ream

Leach water management is one of the few areas in dump leaching subject to operator control. As such, it is of considerable importance. Theoretical considerations indicate that high leach solution application rates are inefficient in washing solubilized copper from dumps. The high rates cause unnecessary dilution of copper values, raising unit recovery costs. Use of excessive amounts of leach solution also cools dumps, resulting in reduced leaching rates. This paper reviews leach solution application methods and details the results of field tests run to determine the benefits and feasibility of low versus high application rate techniques of applying water to dump surfaces.

Jan 1, 1980

By John H. Bassarear, Harold W. Sorstokke

The never ending search for lower unit costs led Pima Min- ing Company's management to study various alternatives shortly after Expansion III was completed. A considerable amount of ore as- saying 0.35% copper had to be moved to maintain mill feed at the desired 0.54 % copper content, which is the overall grade of the ore reserves. Detailed investigations revealed that for a period of 8-10 yr, about 14,000 tpd of 0.30- 0.40% copper ore pass the crusher enroute to the low grade stockpile. This ore is very hard, very clean and has to be mined at a uniform rate. A six month pilot plant run testing autogenous and semi-autogenous grinding gave encouraging results. Since no mining costs need to be charged to the extra tonnage (it had to be mined anyway), the major costs would be against milling. The decision to proceed was made in August 1970. Fluor-Utah was retained as the prime design construction contractor. Ore was put through the new mill on December 29, 1971. By March of 1972 design tonnage

Jan 5, 1973

By J. A. Rajala, R. W. Smith

The effect of increasing ionic strength, via monovalent and divalent ions, on alkyl sulfate flotation of hematite and quartz war investigated. The effects of collector chain length and pretreatment on this flotation were also studied. Sodium hexadecyl sulfate was shown to be a superior flotation collector to sodium dodecyl sulfate for recovery of hematite when there was no salt addition. Similar observation were made when sodium sulfate or sodium chloride was used to control ionic strength. Sodium dodecyl sulfate floated hematite better than its longer chutited counterpart under conditions of low pretreatment temperature and increasing calcium chloride concentration. The flotation recovery for all salt containing pulps was almost always improved after preboiling. Most of the results obtained when the pretreatment temperature was raised were attributed to increased solubility of the collector.

Jan 1, 1984

BECAUSE you cannot always proceed by the ordinary pathway since you sometimes find yourself in a place where you cannot have all that you might need or wish, it often happens that it is necessary to know how to recognize and understand your materials well, in addition to having them well disposed, and to know how to use your, ingenuity in arranging a mould., Furthermore, things have a great diversity among themselves, and it is not possible to give a particular rule for all. But if you have a certain broad fundamental knowledge when you have need of many things, the ingenuity awakens and supplies its needs by imitation. Now, because I have thought that you had not hitherto had the slightest shadow of knowledge of what I have described in this treatise of mine, I have expanded and narrated things in greater detail than perhaps I might have done. For this reason I have also decided that I wish to tell you of several methods that can be used if you wish to mould, especially in making an intaglio* for a relief, t or in making another intaglio in bronze from either an intaglio or a relief. And I will tell how every relief reduces, itself from convex to concave and also how the relief is made from the intaglio. These works are first made of plaster or pastes or some other liquid thing that is soft when moulded and becomes hard either by drying out with heat or by shrinking with cold, such as tragacanth, plaster of Paris, sulphur, lead, wax, or similar things. And, in conclusion, we describe the method of making an intaglio from a solid. In making an intaglio you must first consider whether it is a large or small thing, figure or foliage, whether it is in demi- or bas-relief, and whether it is a thing that projects from the mould wholly or in part.

Jan 1, 1942

Discussion o f Papers. Meetings of the Institute offer opportunity for social acquaintance and exchange of ideas, for the--presentation of papers, and-for discussions. thereon ; also incidentally for viewing under especially favorable conditions mining operations and industrial establishments, and for hospitalities which demonstrate the brotherhood clue to kindred interests. Placing sociability prominent is not to be assumed as relegating other features of meetings to subordinate positions; but during about 40 years of membership in the Institute, the value of acquaintances formed (often ripening into close friendship), and the interchange of data, have frequently demonstrated that the social feature of meetings is of great and lasting value to the membership. Of a roll embracing 4,011 members, resident in all parts of our country, and scattered in various portions of the world, only a small fraction are able to attend meetings, even if the localities selected are alternately widely separated. Hence, the return which most members receive for their annual assessment of dues is limited to the publications issued, and the credit of being recognized as a. member of a great and worthy organization. The greater the value of the contents of our publication, the fuller the return which goes to members. While the Institute disavows responsibility for views or statements made ill papers which appear in its Transactions, the fact that these contributions, after passing proper censorship, are accepted by the Institute and spread before the world may properly be received by the writers as endorsements of their (the writers') ability to present a specific technical or industrial proposition worthy of being carefully read. But the mere presentation and publication of contributed papers falls short of fulfilling one important feature of our meetings. If the purpose is confined to having the writers' views, discoveries, theories, or methods published, this can be obtained through the technical or trade journals and magazines. The true value of a paper presented at a meeting of the Institute may often be gauged by the discussion which it encourages, although there are contributions of decided value which do not especially invite discussion. However, most Of the papers offered contain statements apt to encourage criticism or elaboration by others whose experience or knowledge, or both, assist in combating or endorsing statements made.

Jan 7, 1913

By James H. Neisz, Gregory P. White

This paper discusses the development of surface coal mine planning programs for a microcomputer. A set of seven programs which were originally written for a large mainframe computer are described. The problems encountered in converting these programs to a micro with 52K of available core storage are discussed. A program for economic evaluation which is currently running on the micro is described and plans to convert other programs to the micro are detailed. In addition, we explain the microcornputer system we have assembled and give the rationale for each component. Problems we have encountered with this system are described for the benefit of others who may follow our path.

Jan 1, 1983

By W. H. Lang, C. H. Cox, H. Snell

The treatment of unaltered western phosphate ores by both wet and dry methods is discussed. The objective of the beneficiation is to produce salable Phosphate rock ( 31% P205), with an economic recovery of P205.

Jan 1, 1981

By Aaron J. Miles, Eugene A. Stepenson

The pressure distribution in a producing oil or gas reservoir has been obtained mathematically in a limited number of special cases where the boundary of the reservoirs are simple geometric figures with the wells conveniently located within them. Using some of the previous work as a basis, it can be proved that a number of additional problems of pressure distribution can be solved by use of soap film. This method is particularly applicable to a reservoir drained by a number of wells, or to a reservoir of irregular shape, or to both. Since this method obtains the pressure distribution, it also establishes the drainage boundaries of the wells. This paper derives the analogy between the equation representing the pressure distribution in a reservoir and the equation of the deflected membrane. It also describes the apparatus and the method of operation. The experimental method is employed to solve a problem whose mathematical solution is known and the results compared. These are found to be in good agreement. The method is applicable to any homogeneous liquid, compressible or incompressible, or to a gas, flowing in a reservoir of uniform thickness, permeability and porosity. The flow state may be either the steady state or the transient state wherein the density or pressure of the fluid in the reservoir declines at a constant rate. PRESSURE-DISTEIBUTION PBOBLEM Fluids encountered in the oil reservoir are compressible and expand and move toward the drilled hole where the Dressure is lowest. The loss of fluid from the reservoir lowers the pressure in the more distant parts of the reservoir, permitting the fluids in these parts to expand and move toward the well. The area around the well affected by drainage is increasing continuously, and the density, pressure, and velocity of flow

Jan 1, 1938

By David A. Keys

Applied geophysics is the youngest child of that old branch of learning that has been known from Aristotle's time as physics—the constitution and laws of nature. The mother science, with the help of mathematics, has given birth to many children, who, on becoming of age in the scientific sense, wedded more practical applications which later became known as electrical engineering, physical chemistry and acoustical engineering. Some vigorous sons still retain the family name, among which the most recent to take its place as a division of science is geophysics, which deals with the physics of the earth. Geophysics in its broad sense has many departments—meteorology, oceanography and seismology, to mention only three. Within the past 20 years, however, a special interest has arisen in the application of physical principles to problems in geology, mining and civil engineering, with the consequent rapid growth of what has now been called "applied geophysics." Applied geophysics in this narrower sense is the application of experimental and theoretical physics to determine variations and discontinuities in underground structures that cannot be ascertained from surface inspection. It seems evident, then, that the physics department is the natural place in a university where the principles and methods involved should be taught and developed, for the physicist will also have had the requisite training in mathematics that the proper understanding of many methods now used will require. A knowledge of the procedure and principles, however, is not sufficient for the successful application of geophysical methods. One may know the dynamics of flight of golf balls and of impact and yet not play a par game of golf! The proper selection and use of the right club to suit the circumstances of the lay of the ball and an acquaintance with the possibilities and limitations of the strokes as well as the practical execution of the play is essential to a successful game. So, also, in the application of geophysical methods, it is important for the geophysicist to use the best device under the conditions presented, to know the limitations of the conclusions deduced from his physical measurements and to make the proper interpretation of the results. A knowledge of geology will be of great aid in coming to the correct con-

Jan 1, 1940

By David A. Keys

Applied geophysics is the youngest child of that old branch of learning that has been known from Aristotle's time as physics—the constitution and laws of nature. The mother science, with the help of mathematics, has given birth to many children, who, on becoming of age in the scientific sense, wedded more practical applications which later became known as electrical engineering, physical chemistry and acoustical engineering. Some vigorous sons still retain the family name, among which the most recent to take its place as a division of science is geophysics, which deals with the physics of the earth. Geophysics in its broad sense has many departments—meteorology, oceanography and seismology, to mention only three. Within the past 20 years, however, a special interest has arisen in the application of physical principles to problems in geology, mining and civil engineering, with the consequent rapid growth of what has now been called "applied geophysics." Applied geophysics in this narrower sense is the application of experimental and theoretical physics to determine variations and discontinuities in underground structures that cannot be ascertained from surface inspection. It seems evident, then, that the physics department is the natural place in a university where the principles and methods involved should be taught and developed, for the physicist will also have had the requisite training in mathematics that the proper understanding of many methods now used will require. A knowledge of the procedure and principles, however, is not sufficient for the successful application of geophysical methods. One may know the dynamics of flight of golf balls and of impact and yet not play a par game of golf! The proper selection and use of the right club to suit the circumstances of the lay of the ball and an acquaintance with the possibilities and limitations of the strokes as well as the practical execution of the play is essential to a successful game. So, also, in the application of geophysical methods, it is important for the geophysicist to use the best device under the conditions presented, to know the limitations of the conclusions deduced from his physical measurements and to make the proper interpretation of the results. A knowledge of geology will be of great aid in coming to the correct con-

Jan 1, 1940