Search Documents

By H. V. Winchell

An examination of the Pachucal and El Oro districts in July, 1920, although cursory and incomplete, disclosed facts of more than passing interest to the student of ore deposits; and inasmuch as the literature on these districts is limited and some of their features are little understood, a brief account may prove valuable as reconnaissance observations to be amplified by more thorough and competent observers in the future. Where no complete monograph of important mining camps has been published a partial presentation of the data is often useful, as it sometimes leads to fuller and more accurate descriptions, by stimulating discussion. The following notes are presented with the consent of A. F. Main, managing director of the El Oro Mining and Railway Co., whose fund of information and wide acquaintance with both districts alone made it possible to cover so much ground in a short time. I have also to acknowledge gratefully the aid of C. A. Lantz and D. S. Calland of the Santa Gertrudis and Real del Monte companies, respectively, in connection with permission to inspect geological features of interest in their mines. Pachuca, Hidalgo, Mex. This mining camp has been described by Ezequiel Ordonez2 and by A. F. J. Bordeaux.3 Reported to have been discovered in 1522, it has produced silver valued at between $250,000,000 and $375,000,000. Subsequent to the discovery here, by B. de Medina, of the patio process. in 1557, its production was increased, and now, using cyanidation, the output of the camp is nearly one-sixth of the production of the world. Topography and Climate The Pachuca district consists of a series of mountains and valleys, the minor features of which extend in an easterly and westerly direction and reach elevations of 8000 to 10,000 ft. (2438 to 3048 m.) above the

Jan 1, 1922

I HAVE now traversed for you in the small and fragile bark of my writing all the shores of the deep and spacious sea embracing the uses of material fires, drawn on by my own desire to enrich you with more learning and with the procedures of these things, as much as to satisfy your demands. Having through the grace of God arrived at the appointed end of my voyage and neither knowing nor perceiving a way of going farther, I had decided to furl the [167] sails and cast die heavy anchors into the water in order to enjoy in tranquillity respite from my sailing, when I was warned by my pilot that before I could disembark I should turn my glance backward and reexamine my work in detail to see if there were any part that had by chance remained undescribed in the obscurity of silence. When I did this there immediately appeared in my mind's eye the many sublimates and smoky tinctures that had been made by the burning and most powerful fire of love. I need not say that I knew of it in far-off countries or from the knowledge of others, but I knew it in my own breast and as my very own and can therefore surely esteem it as hotter than all the other fires that the world calls by that name. Although today its sparks and living flames are spent because of my cold and hoary season, nevertheless it is true that the memory of acts of love of long ago still remains with some smoke and warmth. Therefore, since in this work of mine I wish to describe for you the effects and powers of fires, I should logically have spoken of this before any of the others, because of its actual nearness and the great acquaintance I had with it. But since I have had the glance of my intentions directed at distant things, I have behaved as one does who does not see where he places his feet because he is looking at the sky, or as one who thinks about the affairs of others and forgets his own. But now I do not wish to pass over this thing and I wish to correct my error, particularly in order to provide a happier ending to my written work than by remaining among the horrible uproar of guns, powder, and saltpeter, which would be a harsher ending than speaking of love. Never-

Jan 1, 1942

By M. Metzger, J. Intrater

IN the large number of important studies on high-purity aluminum (e.g., recrystallization and grain growth, creep, internal friction), it does not seem to have been generally recognized that the iron content, despite its very low figure, has a strong influence on a number of properties. In part, its influence is due to the very low solubility of the Fe-A1 6 phase. For aluminum of about 99.99 pct purity, the iron content may be 0.001 to 0.004 pct. For values in this range, a second phase will be present below 410" to 480 °C. This was determined by extrapolation of a log solubility vs inverse temperature plot of the solid solubility data of Edgar.' One consequence is the inhibition of grain coarsening below the solubility limit. This is shown in Table I, which gives, for three iron contents, the annealing temperature required for the absence of grains smaller than 1/2 mm average diameter together with the minimum temperature for the presence of some grains larger than 2 mm diameter. The specimens were 1/4x 1 1/2-in. strips cut from hard-rolled 1/16-in. sheet supplied by the Aluminum Co. of America.

Jan 1, 1954

No greater opportunity for public service has ever been presented to the engineers of the United States, as a class, than the campaign to make thrift a permanent American habit, conducted through the Savings Division off the Treasury Department. The engineer owes a duty to his community, to his country, by reason of the very fact that he is an engineer. By reason of his position and influence, his education and experience, he owes to his country the duty of public service. The public understands that the opportunities of the engineer have allowed him to equip himself to handle logically and properly questions affecting the public. He has been trained to maintain a constructive viewpoint. His work is constructive and he builds for the future. The qualities that the public deems necessary for public service have been bred in him. The time has gone by when the professional man can perform his whole duty to himself and his community by shrouding himself and his calling in mystery and locking himself away from the public in office or laboratory. The duty of public service is calling for every man whose training has fitted him to perform that service. The engineers of the country have demonstrated their capacity and their willingness for public service. Throughout the war period they, have been found in every branch of governmental and. civilian activity which could contribute to national success, doing their share to promote national efficiency. Their duties are not over.

Jan 7, 1919

NEW MEMBER, The following list comprises the names of those persons who became members during the period Mar. 10 to Apr. 10, 1915: Members ADAMS, Louis WINFIELD, Supt., Rolling Mills, Lehigh Plant, Bethlehem Steel Co., So. Bethlehem, Pa.. ALLEN, ARTHUR WATTS, Mine Mgr Rodeo, San Juan, Argentina., BALL, EDWIN MARCOTTEL, Mine Supt., Ishkooda. Mines, Care Tenn. Coal, Iron & R. R. Co., H.F.D. 1, Birmingham, Ala. BOLN, CHARLES A., Oil salesman 135 S. 2d St., Philadelphia., Pa. BOYD, DAVID F., Naval Officer Navy Department, Washington, D. C. CAPERTON, GEORGE HENRY Charleston, W. Va. COGGESHALL, GEORGE W., Chem. Engr., Institute of Industrial Research, Washington D C

Jan 5, 1915

By JAMES QATLEY

THE atmosphere, which plays such an important part in the manufacture of iron and steel, is the most variable element involved in its several processes; and particularly is this true of the blast-furnace process, which consumes air in large quantities. At no time since the blast-furnace became an important and widely used apparatus-even when it was operated in the most crude manner-have the variations in composition of the raw materials used been as frequent and as great as the variations in humility of the atmosphere. Important, improvements have been made in the blast furnace and its accessories, such as the hot-blast stoves, the increase in size and change in the shape of the furnace, more efficient blowing engines, the increased protection given to the bosh walls, and the careful preparation of' the raw material, all of which have exerted a pronounced influence on the furnace-operations from a metallurgical standpoint. But during the past eight years little advance has been made in this direction; the fuel-consumption has not diminished, nor has there been any material increase in production. Within that period, however, there has been witnessed the greatest development in appliances for the economical handling of material. So complete has been the work in this direction, that, except in isolated cases, in this country at least., a further extension does not hold out much promise of a satisfactory return on the investment required. It seemed that, with the exception of the gas-engine, we had about reached the limit, for like a strong wall, the atmosphere, with its humility as variable to-clay as when first blown into a primitive blast-furnace, appeared to stand as a Barrier to

Jan 1, 1905

By A. B. Dyes, P. H. Braun, B. E. Cole

This paper presents a reservoir engineering analysis of the performance data for a waterflooding project in the Johnson Lease, South Ward field. This type of engineering analysis adds to the knowledge of the mechanics of water flooding. This study reveals that in general (a) high ultimate areal sweep-out efficiencies (95 to 100 per cent) can be expected, and (b) cross-flow among strata of different permeabilities during the fill-up phase can have an important influence on the behavior and should be dealt with in studying reservoirs for water flooding. The analysis further showed that the recovery predictions based on what was considered a consistent interpretation of core data and logs were low because little contribution was assumed from the low permeability, oil-bearing sand sections which have apparently yielded considerable waterflood oil. This project has yielded in excess of 2 1/2 times as much oil by water flooding as by primary depletion. These very favorable results were achieved without the use of any special injection well completion techniques. However, all of the low permeability material war included in the section open to injection despite its poor estimated primary yield. LEASE PERFORMANCE HISTORY The South Ward field lies in the southeast corner of Ward County near the southern tip of the tremendous Yates trend. Deposition of sand bodies along the seashore reefs during the latter part of the Permian period established what have turned out to be ideal conditions to form a great number of independent productive sands. Probably, these reservoirs in Ward and Winkler counties are providing operators with some of the nation's richest sources of secondary oil reserves through the use of waterflooding techniques. In South Ward field water has been very successfully used to flood oil from the Bennett sand occurring at a depth of about 2,300 to 2,400 ft. About 150 ft above the Bennett sand reservoir, the Grand Falls sand produced gas from a large cap extending over most of the field. The Atlantic Refining Co.'s 320-acre W. D. Johnson lease (Fig. 1) is on the northwest edge of the structure with only gas cap apparently present in the Grand Falls sand. The Bennett sand under this lease is oil productive, however, having a gross sand thickness averaging about 80 ft with a net of 18 ft of fairly clean, highly permeable sand, and about 36 ft of oil-bearing sand with low permeability and high water saturation. The lower permeability sand is interbedded with numerous layers of lime, shale, and anhydrite. Radioactivity logs from 12 wells and cores from two, examples of which are shown in Fig. 2, reveal that the total Bennett sand pore volume is about 71,000 bbl/acre. The estimated initial water saturation averages 41 per cent in the 54 ft of sand considered to contain oil; thus, also considering an estimated 18 per cent oil shrinkage, the lease originally contained about 34,000 bbl of oil per acre. Original pressure was probably about 1,400 psig. PVT correlations indicate that the reservoir fluid was originally saturated with gas. After discovery of the field in 1930, Atlantic completed the first well on the Johnson lease in March,

Jan 1, 1958

By W. F. Hosford

W. F. Hosford, (Massachusetts Institute of Technology) —evelopment of methods for predicting the plastic anisotropy of textured metals is an important step toward the improvement of properties by texture control. The engineering value of the present analysis is indicated by the good agreement between prediction and experimental findings. The purpose of this discussion, however, is to point out the weakness of the assumptions on which the analysis is based. The authors state that "the relative width and thickness strains are believed to depend only on the slip direction" and accordingly they disregard the orientation of the active slip plane. where E,, cW, and et are the tensile, width, and thickness strains, A,, A,, and At are the angles between the tensile axis x, the width direction w, and the thickness direction t, respectively; and G,, GW, and 4 are the angles between the slip-plane normal and x, w, and t, respectively. Therefore, the ratio of width to thickness strains resulting from slip on a single system would be These relations hold regardless of whether the slip plane is a crystallographic plane of the {110}, (1121, or (123) type or whether noncrystallographic slip occurs. If noncrystallographic slip occurs, it might be reasonable to assume that the effective slip plane is the most highly stressed plane containing the slip direction. In this case the slip direction, S.D., the slip plane normal, S.P.N., and the tensile axis, x, are coplanar (Fig. 19) and the angles are related by following expressions: where 9 is the angle between t and the projection of the slip direction in the w-t plane (igs. 1 and 2). The normal strains, Eq. [9], become

Jan 1, 1963

Members whose deaths were reported from Mar. 5, 1919, to Apr. 5, 1920. Elected Died 1895 ANDERSON, ROBERT HAY 1920 1916 ATWATER, M. W 1919 1905 BARD, D. C 1920 1893 BECKER, GEORGE F 1919 1914 BIGELOW, BRAXTON 1917 1917 BLACK, HERBERT F 1919 1911 BOWLER, ROBERT P 1919 1902 BROWN, ARTHUR H 1919 1913 BURNHAM, WILLIAM 1918 1905 Carnegie, Andrew 1919 1900 CARPENTER ROLLA C 1919 1908 CONNER H. MCKEAN 1919 1883 COOK, ROBERT A 1919 1903 COOPER, JOHN 1919 1875 CROXTON, SAMUEL W 1919 1889 DICKMAN, R. N 1919 1893 DUFOURCQ, EDWARD L 1919 1917 FAY, CHARLES H 1918 1875 FOHR, FRANZ 1919 1879 FRICK, H. C 1919 1880 GAYLEY, JAMES 1920 1917 GARVIN, JOHN C 1920 1915 GIBBS, CHARLES H 1919 1917 GODBE, RALPH T - 1918 GREGORY, A. E 1919 1917 HAMILTON, A. McL 1918 1914 HEISE, HENRY C - 1913 HINCKLEY, E. R 1918 1884 JENNINGS, HENNEN 1920 1895 JOHNSON, J. E., JR 1919 1895 KANN, MEYER M 1919 1895 KAYSER, H. W. F 1919 1918 KENNEDY, DANIEL J 1903 KING, PAUL S 1919 1901 LANGTON, JOHN 1920

Jan 1, 1923

By B. Fazan, O. D. Sherby, J. E. Dorn

McLean's technique was employed to determine the effect of temperature on the contribution of grain boundary shearing to the total creep strain in pure aluminum over the range of 610° to 747°K. The contribution of grain boundary shearing at the same stress was found to depend upon a temperature-compensated time, where the activation energy AH was practically identical with that for total high temperature creep. SEVERAL outstanding investigations by McLeanl-' have demonstrated that the total creep strain in polycrystalline aluminum at 473°K arises from microscopically detectable slip, subgrain tilting, and grain boundary shearing. Whereas microscopically detectable slip arises from dislocations that move out of the grains, subgrain tilting is due to entrapment of dislocations of like sign in subgrain bound-arles. Consequently, creep in polycrystalline aggregates appears to be the resultant of two mechanisms, namely, migration of dislocations and grain boundary shearing. This suggests that an appropriate law for creep should contain two additive terms ?1 = ?d + ?yb where the total creep strain, ?1, depends on the sums of the creep strains arising from motion of dislocations, ?d, and from grain boundary shearing, ?yb. But extensive investigations5 over wide ranges of alloys, grain sizes, temperatures, and stresses have shown that the total creep strain is quite accurately dependent on the single term functional relationship ?1 = f (?), s = constant where s is the stress (constant),* ? = te-?H/RT, t is the time under stress, AH is the activation energy, R is gas constant, and T is absolute temperature. Since Eq. 2 was found to be valid over those ranges where appreciable grain boundary shearing is observed, it appears probable that the activation energy for grain boundary shearing might be identical with the activation energy for migration of dislocations. Thus, under a given stress, it could be thought that where fd and fgb represent the appropriate functions for each mechanism of creep. The primary objective of this investigation was to obtain a direct check on the accuracy of this hypothesis. Experimental Procedure and Results Rolled aluminum sheet (99.987 pct Al), 0.100 in. thick, was used in this investigation. Creep specimens having a 0.25 in. wide, 3 in. long gage section were so machined that their axes were in the rolling direction. All specimens were annealed for 9 hr at 894°K before testing to produce a mean grain diameter of about 0.1 in. One face of each specimen was polished electrolytically in 10 pct HBF4. In order to permit accurate measurements of grain boundary shearing, the polished surface was lightly scribed with a ruling machine accurate to ±0.0001 in. to give a uniform grid of lines which were 0.01 in. apart. Although it was thought that surface working might modify the creep behavior in the vicinity of the scribed grid lines, this technique nonetheless was employed because such local differences in creep properties should not modify seriously the fractions of the total creep strain due to grain boundary shearing or to migration of dislocations. All creep tests were conducted under constant load with an initial stress of 250 psi. The specimen tem-

Jan 1, 1955

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselrnan Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo.

Jan 1, 1949

As already announced in the notice of the 114th (New York) Meeting of the Institute, the ladies present met and organized the Women's Auxiliary of the Institute. All ladies of the families of members of the Institute-are eligible to this Auxiliary. The purpose and objects of the Auxiliary are well stated in the address of the President, Mrs. S. J. Jennings, in opening the organization meeting on the morning of Feb. 20, 1917. The address follows: "Ladies: Friends from far and near, on behalf of the Women's Entertainment Committee of the A. I. M. E., I extend to you a hearty welcome. "Most especially are we glad to see our friends from the Pacific Coast and the middle West, .whose royal hospitality to the members of the A. I. M. E. and their wives and daughters on their trips to California and to the Copper Country of the Southwest can never be forgotten. We are glad to be able in some small measure to return it.

Jan 4, 1917

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting). A few mimeographed copies of this provisional report were made. Dr. W. P. Haynes presented some notes prepared by Dr. F. H. Lahee, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Com- mittee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. Sherwin F. Kelly pointed out that much time in university training, which ought to be devoted to technical subjects, was taken .up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. Thom protested against the crowding of high-school material into already overcrowded college curricula. C. E. Dobbin, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1946

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting). A few mimeographed copies of this provisional report were made. Dr. W. P. Haynes presented some notes prepared by Dr. F. H. Lahee, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Com- mittee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. Sherwin F. Kelly pointed out that much time in university training, which ought to be devoted to technical subjects, was taken .up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. Thom protested against the crowding of high-school material into already overcrowded college curricula. C. E. Dobbin, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1946

By C. H. Frick

BEFORE presenting the main topic, as indicated by the title, this paper will give some of the high-spot history of the anthracite industry. INTRODUCTION The earliest recorded use of anthracite was in the year 1762, when a company of Connecticut pioneers discovered anthracite near the present city of Wilkes-Barre, Pennsylvania. In the early days of the industry, the coal was used only in large pieces, the smaller pieces being discarded to waste piles. As the output of the industry increased during the nineteenth century, uses were developed for somewhat smaller sizes down to and including pea coal. Early in the twentieth century, sizes smaller than pea, such as No. I and No. 2 buckwheat, were developed and used. Accu¬mulations of piles from current mining operations were still increasing; that is, the smaller sizes were still being discarded. It was not until after World War I that preparation of the so-called steam sizes began commercially. This was largely No. 3 buckwheat, which is screened through a 3f 6-in. round-hole screen and over a 332-in. or a M 6-in. round-hole screen. USE OF SMALLER SIZES The earliest recorded experience in burning the small sizes of anthracite for steam production, other than in a previous small experiment, was in the year 1913, when a size known as "boiler fuel" was introduced-a mixture of rice and barley (No. 2 and No. 3 buckwheat). At that time, there was still no method known for burning the still smaller sizes. TABLE I.-Screen Sizes Used for Small Sizes of Anthracite [ ] At the present time, various sizes down to and including No. 5 buckwheat are being prepared (Table I) from current mining and bank-reclaiming operations. The sizes of No. 4 and No. 5 buckwheat and smaller are generally being used for steam production in large boilers. The Pennsylvania Power and Light Co., following World War I, used 680,000 tons of anthracite per year, burned largely on stokers for production of steam, whereas for the year 1943 it used 1,940,000 tons of stoker sizes and 400,000 tons of smaller sizes for grinding and burning in pulverized form. This company has taken a very large part in the research and development of ways and means of burning these smaller sizes of anthracite, including the grinding of the very small sizes. This paper is particularly concerned with the latter feature.

Jan 1, 1946

By Paul Pietrokowsky

THE formation of intermediate phases in the solid state reaction of titanium with silicon, germanium. and tin (of subgroup 4B in the periodic table) was the subject of a recent paper.' Further investigation of the system Ti-Sn revealed the presence of a new compound on the titanium-rich side of this phase diagram. Metallographic evidence indicated that this new phase was situated very close to 75 atomic pct Ti. The present work is concerned with the crystal structure of the intermediate phase Ti3Sn. Iodide-process titanium metal, furnished by the New Jersey Zinc Co., was used in this investigation. The metallic tin was received in powder form from Charles Hardy Inc., New York; its purity was 99.80 pct. The titanium rod was machined into small cups 1 cm in diam and about 1.5 cm in height. The tin powder was compacted, melted, and then placed in the titanium cups and alloyed by electric arc melting in a helium atmosphere. The alloys, weighing approximately 8 g, were sealed in evacuated quartz tubes and homogenized at 1030°C for 5 days. This isothermal heat treatment was terminated by a water quench from the soaking temperature. Filings of the alloyed pellets were sealed in evacuated quartz bulbs and quenched from 1030°C into liquid argon. A 14.32 cm Debye Scherrer X-ray camera was used for the powder diffraction study. The copper radiation was filtered. X-ray diffraction data for the compound Ti3Sn are given in Table I. The data were indexed on the basis of a hexagonal lattice. Good agreement between observed and calculated values of the square of the reciprocal interplanar spacings was obtained with the following expression: (1/d)2 = 0.03810 (h2 + hk + k2) + 0.04410 (l2) Unit cell parameters were calculated by the method of least squares from the reflections (20.3), (22.2), (40.1), and (42.1); ao = 5.916 & 0.004A, co = 4.764 ± 0.004A, and co/ao = 0.805. The relatively small size of the unit cell allowed the unambiguous indexing of most of the reflections from planes of large spacing. An inspection of the assigned indices (Table I) reveals the absence of (hk.l) reflections when 1 2n. A systematic absence of this type leads to the space group C 6/mmc or one of its subgroups. Assuming, for a first approximation, a linear increase in the density of titanium with the addition of tin, it follows that there are two stoichiometric molecules of Ti3Sn per unit cell. The density calculated from X-ray measurements is 5.194 g cm-'. At this point it became clear that Ti3Sn might be isomorphous with Mg3Cd. The 6 Ti and 2 Sn atoms were placed in the following positions of space group D4 6h, C 6/mmc: 6Tiin (h): X 2X 1/4; 22;; 1/4;Xx 1/4;x2x3/4; 2x x 3/4; x x 4; with x = 516 2 Sn in (c): 1/3 2/3 1/4; 2/3 1/3 3/4.

Jan 1, 1953

By John S. Crandall

Occurrence: small crystals in alluvial sands from the eroding Belt Series mica schists. Flowsheet: dragline, trommel screen, jigs, drier, crusher, screens. Value: ground, $2.50 per cu yd, garnet sand gross $60. per ton. Costs: production and sales $48. per ton. Uses: blasting sand in aircraft plants, monumental works, foundries. Efficiency comparison: superior to silica sand. Future: possibilities only touched upon, research continuing.

Jan 1, 1950

The annual world production of minerals approximates 1,700,000,000 tons, over 90 per cent. of which consists of coal and iron. Of this amount about two-thirds is used within the countries where the minerals are produced and one-third is shipped to other countries. The movement of most of these minerals, though, shows a rather remarkable concentration. For instance, manganese moves from three principal sources and converges at four or five consuming centers; chromite and tungsten move from two principal sources. The United States is more nearly self-sustaining in regard to mineral commodities as a whole than any 'other country on the globe; but the interests of conservation - call for an international viewpoint in the handling of our mineral resources., There is perhaps as much need of specializing in mineral output as there is of specializing in manufacturing. The thought that every country on the globe should be self-sustaining in regard to mineral supplies is of somewhat the same order as the thought that every family should produce all its own raw materials rather than take advantage of the more favorable conditions existing elsewhere and so specialize in human effort. Extension of international control of minerals seems to offer possibilities of loss and gain-loss through a considerable sacrifice of national trade .and a narrowing of the field for private initiative in trade; gain through the possibility of attaining certain ends which are attainable only by international agreement, such as an allocation of supplies which will be to the advantage of the greater number of nations rather than to the advantage of the few that are strong enough to dominate the situation. The interests of conservation clearly require international control. Moreover, the lesson of the war points to the necessity of overhauling old international understandings and machinery, even though such a task would encounter great difficulties, not the least of which lie in the persistence of human habits and inertia. Whether the time has come to establish a league of nations with economic control can be determined only by our individual and collective answers to the question whether we are willing to make the necessary economic sacrifices, individually and nationally, in the interest of world harmony. The mineral industry should fully understand that, with international control, efforts to promote export will need to be modified and curtailed; that expansion of our trade in many lines will mean equivalent loss of trade to other nations; that the almost universal conception that expansion of foreign trade is a meritorious aim and end in itself, without regard to its effect on other countries, will need revision.

Jan 3, 1919

By Lester Uren

Beginning with theoretical concepts of oil drainage, this paper demonstrates that the flow of petroleum into a well from a stratum of oil-saturated sand of uniform texture increases with the diameter of the well. This conclusion is supported by experimental evidence. It appears that if a well may be reamed to a diameter of 20 ft. within the oil sand, its production will be approximately doubled. A novel method is proposed for forming and supporting a cavity of such proportions within the oil-producing stratum. PETROLEUM occurs, in nature, as a fluid saturating the pore spaces between the grains of porous rocks or aggregations of rock particles such as sand, sandstone, conglomerate, shale, limestone, etc. The oil, under the influence of gas pressure, hydrostatic pressure, gravity, earth pressure, and, perhaps, other natural forces, is caused to flow through the porous "reservoir rock" into wells penetrating the stratum in which the oil occurs. The principal moving force is the pressure of dissolved or occluded natural gas within the oil, though this;, force is assisted by gravity and by the hydrostatic or buoyant pressure of ground water about the edges of the "pool." The wells, providing outlets to the surface, are centers of reduced pressure and the flow of rock fluids into a particular well is usually an expression of the difference in pressure existing between the space within the well and that of the stored oil .within the reservoir rock. The greater this differential pressure, the more rapidly will oil flow from the source rock into the well. Opposing movement of the oil from the reservoir rock into the well are certain natural forces related to the rock structure, such as pore friction and capillarity, and certain others related to the physical properties of the oil, such as viscosity and adhesion. The differential pressure between the well and the boundaries of the area drained by it must be sufficient to overcome the forces opposing flow if there is to be movement of oil into the well. If by any device the resistance to movement of the oil may be reduced, the oil will flow into the well at a more rapid rate and the effective area of drainage will be increased.

Jan 10, 1924

By R. W. Fountain, M. Korchynsky

The precipitation phenomena occurring in cobalt-tantalum alloys have been investigated in the temperature range frm 500" to 1050°C by correlating the results of metallographic, X-ray, micro-and macrohardness, and electrical resistivity studies. The property andmacrohardness,changes were found to depend on 1) general precipitation, and 2) lamellar precipitation. Two new intermetallic phases have been identified: 1) a Co3Ta, a metastable ordered face-centered-cubic compound, and 2) a stable ß Co3Ta phase of hexagonal structure. In addition, the previously reported Co2Ta phase was found to exist in two allotropic modifications: the hexagonal MgZn,-type and the cubic MgCu2-type Laves phases. SINCE a large variety of structures can result as a consequence of the decomposition of a solid solution, predictions on the nature of property changes are difficult, if not impossible, to make. For any rational attempt to correlate properties and structures of a precipitation-hardenable alloy, a detailed understanding of the kinetics of decomposition and morphology of phase separation, as well as knowledge of phase relationships, appears to be prerequisite. Information of this type has been accumulated in the past for many alloy systems, both of theoretical and pastforpractical importance.1,2 Although the presence of intermetallic compounds has been reported in cobalt-base alloys,3 the amount of published information on precipitation-hardenable cobalt-base systems is very limited. A survey of the binary phase diagrams of cobalt indicates that cobalt-tantalum alloys might be of interest as typical of other cobalt-base systems in which Laves phases of the A,B type can be precipitated from solid solution. The present work has been undertaken, therefore, to study the kinetics and morphology of the precipitation reaction in this system and to establish a base for a correlation between the structural aspects and properties in this class of alloys. PREVIOUS WORK The only available phase diagram of the cobalt-tantalum system is based on the work of Koster and Mulfinger. According to these authors, the maximum solubility of tantalum in cobalt is about 13 pct (at 1275°C) and. less than 7 pct at room temperature. Tantalum additions lower the temperature of allotropic transformation of cobalt (about 420°C), and at 7 pct Ta, the high-temperature face-centered-cubic modification (ß cobalt) is retained at room temperature. The precipitating phase was originally designated as Co5Ta2 compound (55.2 pct Ta, about 1550°C melting point), but subsequent investigations by wallbaum5" identified this constituent as the A,B-type Laves phase. Wallbaum's data indicate that there are two modifications of this intermetallic compound: one richer in cobalt (Co2.2 Tao.8)of the hexagonal MgNi, type; and another of a higher tantalum content (Co2Ta) of the cubic MgCu, type. On the other hand, Elliott7 found that the cobalt-rich alloy (CO2.10,Tao.~l) was predominantly the cubic MgCu, type at 800°C and a mixture of both the MgCu2 and the hexagonal MgZn,-type Laves phases at 1000°C. At 1200°C, Elliott found only the MgZn, type while at 1400°C, he observed only the MgCu2 type. At the stoichiometric composition, Co2Ta, Elliott reported only the cubic MgCu2-type Laves phase in the temperature range of 600oto 1600°C. The precipitation of the cobalt-tantalum intermetallic compound is accompanied by a marked increase in hardness. According to Koster's4 data, the Brinell hardness of an 8 pct Ta-Co alloy increases from 230 to 340 upon short-time aging at 800°C. EXPERIMENTAL PROCEDURE The binary cobalt-tantalum alloys investigated contained 5, 10, and 15 pct Ta. The range of tantalum additions was thus slightly broader than the reported minimum and maximum solid solubility limits of tantalum in cobalt (7 and 13 pct, respectively)4 The alloys were vacuum-induction melted in a magnesia crucible using cobalt rondelles and technically pure tantalum sheet as raw materials. Deoxidation of the melt was accomplished with carbon, and the chemical analysis of the alloys is given in Table I. The effect of isothermal aging treatments on the progress of precipitation was studied on samples cut from cast ingots. These samples were solution treated for 2 hr at 1250°C and water-quenched. Aging was conducted in the temperature range from 500" to 1050°C for periods between 15 min and 1000 hr and followed by water-quenching. To prevent contamination from the atmosphere, all samples were sealed in evacuated Vycor or quartz tubes for heat-treatments. For solution treatment, argon at 0.2 atmospheric pressure was introduced prior to sealing of the capsule to prevent collapse at high temperature, and titanium sponge was placed at one end of the capsule to act as a getter. MACROHARDNESS The effect of aging on Vickers hardness (Dph) of

Jan 1, 1960