Search Documents

By H. B. Pulsifer

.ABOut 1.5 varieties, or tnodifications, of the best rnagnesiurn available were prepared and subjected to etching tests, then examined for micro-structure. Of the 30-udd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressule cold metal deforms slightly, then shears to fracture without plastic flow. The chief structural features of magnesium arc presented in two reduced photographs and 30 photomicrographs. Materials Tested There are only two sources in the United States from which new metal can be procured: the American Magnesium Corpn. and the Dow Chemical Co. No pronounced structural or property differences in the metals from these two companies were disclosed by the work of this investigation. The following materials were obtained from the manufacturers: 1. Massive crystals of distilled metal (American Magnesium Corpn.). 2. Rods of hot-extruded metal, ½-in. squares and 5/8-in. rounds (American Magnesium Corpn.). 3. Sheet magnesium, 0.005-in. thick (American Magnesium Corpn.). 4. Cast stick metal, 13/8-in. dia. (Dow Chemical Co.). 5. Magnesium-aluminum alloy, hot-rolled plate, ½-in. thick (American Magnesium Corpn.). From these materials, were prepared: 6. Sections from a furnace-cooled ingot made from clistilled crystal. 7. Cold-strained pieces from (6), (4) and (2). 8. Pieces cold-squeezed to fracture from (6), (4) and (2). 9. Hammer-struck pieces from (6), (4) and (2). 10. Steam-hammer struck pieces from (6), (4) and (2). 11. Sections from furnace-cooled ingot of the magnesium-aluminum alloy.

By H. B. Pulsifer

ABOUT 15 varieties, or modifications, of the best magnesium available were prepared and subjected to etching tests, then examined for microstructure. Of the 30-odd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressure cold metal deforms slightly, then shears to fracture without plastic flow. The chief structural features of magnesium are presented in two reduced photographs and 30 photomicrographs. MATERIALS TESTED There are only two sources in the United States from which new metal can be procured: the American Magnesium Corpn. and the Dow Chemical Co. No pronounced structural or property differences in the metals from these two companies were disclosed by the work of this investigation. The following materials were obtained from the manufacturers: 1. Massive crystals of distilled metal (American Magnesium Corpn.). 2. Rods of hot-extruded metal, ½ -in. squares and 5/8-in. rounds (American Magnesium Corpn.). 3. Sheet magnesium, 0.005-in. thick (American Magnesium Corpn.). 4. Cast stick metal, 1 3/8-in. dia. (Dow Chemical Co.). 5. Magnesium-aluminum alloy, hot-rolled plate, ½ in. thick (American Magnesium Corpn.). From these materials, were prepared: 6. Sections from a furnace-cooled ingot made from distilled crystal. 7. Cold-strained pieces from (6), (4) and (2). 8. Pieces cold-squeezed to fracture from (6), (4) and (2). 9. Hammer-struck pieces from (6), (4) and (2). 10. Steam-hammer struck pieces from (6), (4) and (2). 11. Sections from furnace-cooled ingot of the magnesium-aluminum alloy.

Jan 1, 1928

By R. E. Head

Under existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes. Surface Contamination The experience gained by microscopic study of numerous gold ores and tailings has shown that there are pronounced differences in the physical characteristics of the minerals composing them, more especially of the gold. Repeated studies of tailings from flotation and cyanidation of gold ores has established the fact that surface contaminations on gold particles are often directly responsible for high gold losses; comparison of gold particles isolated from flotation concentrates and the resulting tailings have showed that the clean gold has been recovered and the tarnished or contaminated gold invariably lost in the tailing. Obviously, it is not possible to make such a comparison of gold ores treated by cyanidation, as the clean gold has been taken into solution; but when the gold found in cyanide tailing has a tarnished or coated surface, one may infer, with a reasonable degree of certainty, that the clean gold has been extracted. This premise is supported by experimental evidence obtained by isolating particles of tarnished gold and exposing them to cyanide solution in small parting cups. In one such experiment, tarnished gold particles picked from a cyanide tailing showed but slight evidence 01 dissolving at the end of 27 days. In this test, a cyanide solution of 1.6 11). per ton was used and the leach solution was decanted arid renewed every

Jan 1, 1939

By R. E. Head

Under existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes. Surface Contamination The experience gained by microscopic study of numerous gold ores and tailings has shown that there are pronounced differences in the physical characteristics of the minerals composing them, more especially of the gold. Repeated studies of tailings from flotation and cyanidation of gold ores has established the fact that surface contaminations on gold particles are often directly responsible for high gold losses; comparison of gold particles isolated from flotation concentrates and the resulting tailings have showed that the clean gold has been recovered and the tarnished or contaminated gold invariably lost in the tailing. Obviously, it is not possible to make such a comparison of gold ores treated by cyanidation, as the clean gold has been taken into solution; but when the gold found in cyanide tailing has a tarnished or coated surface, one may infer, with a reasonable degree of certainty, that the clean gold has been extracted. This premise is supported by experimental evidence obtained by isolating particles of tarnished gold and exposing them to cyanide solution in small parting cups. In one such experiment, tarnished gold particles picked from a cyanide tailing showed but slight evidence 01 dissolving at the end of 27 days. In this test, a cyanide solution of 1.6 11). per ton was used and the leach solution was decanted arid renewed every

Jan 1, 1939

By L. M. Pidgeon, K. T. Aust

There has been considerable interest in the possible use of titanium in magnesium alloys.' Zirconium has shown some promise in this connection2 and its general similarity with titanium suggests that the latter might act in a similar manner. A literature survey revealed that quantitative data on the Mg-Ti system was unavailable. Several patents3 have claimed that titanium additions from 0.2 to 4 pct to magnesium alloys were possible, but no mention was made as to the form in which the titanium existed in the alloy. Kro114 succeeded in introducing only traces of titanium into magnesium by bubbling TiCl4 through the metal under argon or by reacting it with sodium titanium fluoride. The application of theoretical data given by Carapella5 based on Hume-Rothery's principles, involving atomic size factor, crystal structure, valency and the electro-chemical factor, suggests that a Mg-Ti alloy is a favorable case, and the system appeared to warrant experimental examination. Experimental Procedure and Results THERMAL ANALYSIS If titanium is appreciably soluble in magnesium, a change in the melting point of the magnesium might be detectable using standard cooling curve methods. Magnesium was melted in graphite crucibles under an argon atmosphere, the assembly being enclosed in a silica tube. Graphite thermocouple protection tubes served also to stir the melts. The apparatus was very similar to Fig 1, with the addition of a refractory and baffle system to prevent undue heat losses from the top of the crucible. Chromel-alumel thermocouples were calibrated using Al of 99.97 pct purity. Dominion Magnesium Limited sup- plied redistilled high purity magnesium of the analysis given above. Titanium was added in three different forms: 1. Titanium powder —100 mesh, from the Titanium Alloy Manufacturing Co., Niagara Falls, N. Y. 2. Sheet titanium from the U.S. Bureau of Mines, produced by Mg reduction of TiCl4. 3. Magnesium —50 pct titanium master alloy from Metal Hydrides Inc., Beverly, Mass. The melting point of the high purity magnesium used was measured experimentally as 651.0°C. More than a dozen tests were conducted using titanium from the three sources referred to above, in calculated additions up to 20 pct titanium, at temperatures between the melting point and 1000°C and holding periods up to 6 hr. In no case was evidence obtained of solubility of titanium in magnesium, using inverse-rate and time-temperature curves. The melting point of the magnesium was unchanged within the accuracy of measurement, namely -+0.5°C; and no other thermal arrests were detected. Metallographic investigation of the thermal analysis billets indicated that the titanium additions were apparently mechanically entrapped in the magnesium in segregated areas. Consequently, these samples were not analyzed for titanium. The master alloy proved to be a mechanical mixture of titanium particles in a magne- sium matrix. These results indicated that the titanium solubility, if such existed, could not be obtained by the usual thermal methods. X RAY DIFFRACTION INVESTIGATION In an effort to detect solubility of titanium in magnesium, samples were investigated using both the Debye-Scherrer and the Focusing Back-Reflection methods. Filings from samples of the thermal analysis billets and from pure magnesium were annealed in argon one hour at 350°C to relieve mechanical strain. Measurements made of the interplanar spacings showed no difference between the Mg-Ti samples and pure magnesium. The interplanar spacings could be measured to within 0.0002A, and the greatest variation found was 0.0004A, in the back-reflection method. The diffraction lines for magnesium were not shifted by the titanium additions indicating that the solid solubility of titanium in magnesium is of a very low order—less than 0.5 pct. From both diffraction methods, a d or interplanar spacing of 0.817A was obtained for the redistilled high purity magnesium. This latter value is not given in the standard X ray diffraction cards for magnesium metal or vacuum distilled magnesium. Theoretical calculations for a close-packed hexagonal space lattice for magnesium indicate that the planes {2134) should give a line which was found. The relative intensity for this reflection at 0.817A is slightly less than that at 0.870k for magnesium. SOLUBILITY OF TITANIUM IN LIQUID MAGNESIUM The Mg-Mn system was examined by Grogan and Haughton6 who were

Jan 1, 1950

By David R. Maneval, Sylvester Lemezis

All acid mine drain waters, regardless of source, share certain characteristics; but they do differ in exact chemical composition, degree of acidity, and total solids content. Any serious program to treat such waters must recognize these differences and apply to each specific case the technique which offers the best promise of each specific case the technique which offers the best promise of technical and economic success. The Pennsylvania Dept. of Mines and Mineral Industries has originated and funded studies of many different treatment means. Neutralization with lime is now being used on 200 different polluted streams in Pennsylvania, and multistage flash evaporation has been selected for a particularly large and troublesome outfall near Wilkes-Barre, Pa. A 5 x 106 gpd plant for this latter site is now being designed by Westinghouse Electric Corp. which developed a concentration process based on multistage flash evaporation as part of the State's research program.

Jan 1, 1973

By H. A. Hancock, L. M. Pidgeon

Equilibrium carbon monoxide pressures were measured over the reaction between chromium oxide and a number of solid ferrochromium alloys in the composition range 0.4 to 4.8 pct C and 0 to 49 pct Fe. Measurements were also made for the carbides Cr23C6 and Cr7C3 which agreed well with previous investigations. Between 1050°and 1400°C the pvessures varied from 0.1 to 56 mm and increased markedly with the iron and carbon contents of the alloys. The data were used to estimate the activity of carbon in the alloys and to calculate the equilibrium conditions for the decarburization of a useful range of ferrochromium alloys. WHEN ferrochromium is produced by the reduction of chromite with carbon in an electric arc furnace it invariably contains up to 10 wt pct C. For many purposes such as the production of stainless steel, it is necessary that the carbon content be as low as from 0.02 to 0.05 pct. Thus an important part of the ferrochromium industry consists of the production of low carbon ferrochromium. The classical Bessemer steelmaking technique cannot be used to oxidize low carbon contents in chromium and ferrochromium alloys without also oxidizing the chromium. Recently a new commercial process2-4 has been introduced for oxidizing carbon from high chromium content alloys which consists of heating the solid alloy with such oxidizing agents as Cr2O3, Fe2O3, or SiO2 in a retort at reduced pressures. By maintaining the carbon monoxide pressure below the equilibrium value for the system, the carbon can be removed as carbon monoxide without oxidizing the chromium. The equilibrium conditions for the decarburization of solid chromium carbon alloys have been determined by Boericke5 who measured the carbon monoxide pressure over the reaction between the various chromium carbides and chromium oxide. A typical reaction is shown below. Cr23C6 + 2Cr2O3 =u 27Cr + 6CO [1] These values are not applicable to the decarburization of commercial ferrochromium alloys which invariably contain major amounts of iron. The present investigation was therefore undertaken to measure the change in the equilibrium carbon monoxide pressure brought about by additions of iron to the Cr-C-0 system, thus extending the work of Boericke into the region of the production of low carbon ferrochromium. MATERIALS AND METHOD Materials. Measurements were made on two carbides of chromium, Cr233C6 and Cr7C3, and fifteen Fe-Cr-C alloys. The chromium carbides were made

Jan 1, 1963

By P. G. Dunn

Geologic studies during development at Copper Flat were directed at acquiring the necessary information in evaluating a low-grade porphyry copper deposit. In addition to the geologic mapping and core-logging of a typical exploration project, these studies included: - careful checks on the sampling and assaying, - selection of representative samples used to establish the recoverable amounts of precious metals in the ore, - examination of underground workings driven to provide samples both for metallurgical testing and for assay comparison, - evaluation of plant site and waste dump areas as non-material, including a placer examination of the tailings disposal area, and location of an adequate water supply. All these investigation were carefully documented to provide the necessary data both for the engineering design and, more importantly, for the feasibility studies required for successfully financing the project.

Jan 1, 1985

By H. P. Leighly

WORNER1 briefly studied the embrittlement of titanium by mercury. He found that mercury will wet the titanium surface at 400°C in vacuo, if the specimen had been heated previously to 700°C to dissolve the oxide coating. Subsequent exposure to the atmosphere causes the mercury film to recede rapidly. Bending of the titanium specimen even after the mercury film has receded results in a brittle fracture. For the study of the embrittling effect of mercury on titanium, specimens 2 by 12 by 0.051 in. were cut from RC-130-A sheet, an alloy having a nominal 8 pct Mn content and a mixed a-ß structure. The specimens were stressed horizontally at a predetermined value after which a plastic ring having a cavity 1/2 in. diam by 1/2 in. deep was placed on the specimen. The cavity was filled with mercury and a hole was drilled in the specimen through the pool of mercury. If the stress level was high enough, fracture occurred instantaneously with the drilling. By repeating the test at different stress levels, the threshold stress can be determined. Mercury embrittlement causes a drastic reduction in the ultimate tensile strength of this alloy from 132,000 psi to about 15,700 psi. The drilling of the hole, in the absence of mercury, does not change the tensile properties. Fig. 1 shows the typical fractures observed as a result of the embrittlement of this alloy by mercury. The central portion of the fracture was brittle represented by the jagged region which appears to have occurred on the shear planes at about 45 deg to the stress axis. Ductile fracture, which is perpendicular to the stress axis, occurred near the specimen edges accompanied by a reduction of the specimen thickness. Examination of the fracture reveals that only in the brittle region does mercury wet the

Jan 1, 1962

By J. R. Thoenen

The Bureau of Mines has used various sizes of core barrels above 2 in. and below 10 in. in diameter to core manganese, potash, coal, brown iron ore and bauxite. The paper describes in some detail the methods and types of equipment used to obtain maximum sampling accuracy. Introduction On December 11, 1946, R. D. Longyear, in his capacity as Chairman of the Subcommittee on Exploration Drilling, wrote the author requesting him to prepare a paper presenting the collective ideas of engineers in the Bureau of Mines on the design, standardization and application of core barrels using diamonds or other hard cutting media for drilling holes larger than two inches and less than ten inches in diameter. In subsequent correspondence it was indicated that similar papers covering the experience of other government agencies would be solicited and all such papers received would be combined in a symposium on the subject for discussion at the March 1947 meeting of the Mining Methods Committee AIME. In soliciting such information from other Bureau engineers, it developed that most Bureau experience had been confined to standard core size, two inches or less in diameter, and that larger sizes had been used only for special purposes. It is hoped the data contained herein will be of help to other operators in solving problems encountered in the field. Acknowledgments This paper was made possible by the request of Lowell B. Moon, Chief, Mining Division, Bureau of Mines, to all Division engineers to send to the author any data they had on the subject. Engineers of the Mining Division contributing were: M. H. Kline, Chief, Raleigh Branch. Paul T. Allsman, Chief, Salt Lake City Branch. J. H. Hedges, Chief, Tucson Branch. C. H. Johnson, Chief, Rolla Branch. A. M. Evans, Mining Engineer, College Park Branch. Wing Agnew, Engineer in charge, Mount Weather, Virginia. Andrew Brown, Mining Engineer, Tus-caloosa Branch. In addition Albert L. Toenges, Supervising Engineer, Bituminous Coal Mining Section, Pittsburgh, contributed his experience in coring coal beds. The author's experience in the use of cores within the limits stated has been confined to the brown iron-ore work described by Brown and coring bauxite and clay in Arkansas. Design and Standardization of Core Barrels Bureau engineers are primarily interested in obtaining core that will best represent

Jan 1, 1949

By J. R. Thoenen

The Bureau of Mines has used various sizes of core barrels above 2 in. and below 10 in. in diameter to core manganese, potash, coal, brown iron ore and bauxite. The paper describes in some detail the methods and types of equipment used to obtain maximum sampling accuracy. Introduction On December 11, 1946, R. D. Longyear, in his capacity as Chairman of the Subcommittee on Exploration Drilling, wrote the author requesting him to prepare a paper presenting the collective ideas of engineers in the Bureau of Mines on the design, standardization and application of core barrels using diamonds or other hard cutting media for drilling holes larger than two inches and less than ten inches in diameter. In subsequent correspondence it was indicated that similar papers covering the experience of other government agencies would be solicited and all such papers received would be combined in a symposium on the subject for discussion at the March 1947 meeting of the Mining Methods Committee AIME. In soliciting such information from other Bureau engineers, it developed that most Bureau experience had been confined to standard core size, two inches or less in diameter, and that larger sizes had been used only for special purposes. It is hoped the data contained herein will be of help to other operators in solving problems encountered in the field. Acknowledgments This paper was made possible by the request of Lowell B. Moon, Chief, Mining Division, Bureau of Mines, to all Division engineers to send to the author any data they had on the subject. Engineers of the Mining Division contributing were: M. H. Kline, Chief, Raleigh Branch. Paul T. Allsman, Chief, Salt Lake City Branch. J. H. Hedges, Chief, Tucson Branch. C. H. Johnson, Chief, Rolla Branch. A. M. Evans, Mining Engineer, College Park Branch. Wing Agnew, Engineer in charge, Mount Weather, Virginia. Andrew Brown, Mining Engineer, Tus-caloosa Branch. In addition Albert L. Toenges, Supervising Engineer, Bituminous Coal Mining Section, Pittsburgh, contributed his experience in coring coal beds. The author's experience in the use of cores within the limits stated has been confined to the brown iron-ore work described by Brown and coring bauxite and clay in Arkansas. Design and Standardization of Core Barrels Bureau engineers are primarily interested in obtaining core that will best represent

Jan 1, 1949

By J. H. Polhems, R. B. Brackin, D. B. Grove

THE heavy media separation process plays an outstanding role in the concentration of 4000 tons of zinc ore per day at the Mascot mill of the American Zinc Co. of Tennessee. Of the total tonnage, 72 pct is treated in the heavy media separation plant to reject 56 pct of the ore as a coarse tailing, which has a ready market. Concentrates from this separation are beneficiated further by jigging and flotation. Approximately 25 pct of the total zinc concentrate production is made in the jig mill. Jig tailings are ground and pumped to the flotation circuit where the balance of the production is made. Fig. 1 shows a generalized flowsheet of the mill. The Mascot ore is a lead-free, honey-colored sphalerite in dolomitic limestone, with lesser amounts of chert and some pyrite. A mineralogical analysis is given in Table I. After 10 years of successful operation with galena medium and treatment of nearly 10,000,000 tons of ore, a decision to convert to ferrosilicon was made early in 1948 because of the increasing price of galena and consequent high operating costs. The conversion was made on Nov. 6, 1948, and the results obtained since that time have shown remarkable improvement over those made with galena. The Table I. Mineralogical Analysis of Mill Feed, Pct Calcium carbonate 49.5 Magnesium carbonate 35.2 Iron oxide and aluminum oxide 1.5 Zinc sulphide 4.5 Insoluble 9.3 100.0 Table II. Comparative Data, Galena and Ferrosilicon Ferro- Diner-Gelenaa siliconb ence Operating costs per ton milled, ct. 21.21 9.12 12.09 Medium consumption per ton milled, lb 0.80c 0.15 0.65 Reagent consumption per ton milled, lb 0.45 0.02 0.43 Tailing assay, pct Zn 0.310 0.297 0.013 Concentrate. oct Zn 12.08 10.33 1.75 Heavy medla ieparatlon recovery. pct 89.38 90.22 0.84 Mill feed rate, tons per hr 153 166 13 Heavy mesa separation feed rate. tons per hr 100 10 0 Tons milled per heavy media separation man shift 350 620 270 Mill feed to coarse tailings, pct 51.0 56.7 5.7 Lost mill time, pct 5.6 5.0 0.6 Power consumption, kw-hr per ton 2.06 1.92 0.14 a 1947. " First 6 months of 1950. c Net consumption after deducting credit for reclaimed waste galena. Consumption of new galena was 1.320 lb per ton milled. For entire life of galena operation, a credit of 40 pct of the value of the new galena added was realized from the sale of waste galena. comparisons given in this report cover the first 6 months of 1950 as representing the ferrosilicon operation, and the year 1947 as representing the galena operation. This was the last full year in which galena was used exclusively and is representative of the best work done during the 10 years of operation with this medium. After only 2 years' operating experience, with ferrosilicon and treatment of 1,807,585 tons many advantages have been revealed and are summarized in Table 11. Development Prior to the introduction of the heavy media process, all the mill feed was crushed through 5/8 in. and treated by jigging. A finished tailing assaying 0.66 pct Zn was made on rougher bull jigs, and cleaner jig tailings were ground for treatment by flotation. The first test work on the sink-and-float method of mineral beneficiation was carried out at Mascot in 1935, using a 3-ft cone and galena medium for batch tests. The following year a 6-ft cone was installed for pilot-plant work. This unit became a part of the mill circuit on March 1, 1936, and handled a gradually increasing tonnage in the next 2 years as the process developed to the point where it could treat all the + 3/8-in. material in the mill feed. Coarse jigging was then discontinued on March 1, 1939, and all coarse tailings have been made by the heavy media separation plant since that time. Feed Preparation: The original feed preparation plant consisted of a drag washer followed by two 4x10-ft Allis-Chalmers washing screens. A surge bin and two additional 5x12-ft AC washing screens were added in 1943. Use of primary and secondary washing screens was found essential to provide the cleanest possible feed for the cone and thereby avoid excessive contamination of the galena medium. Improved washing was obtained by replacing the drag washer with a 7x20-ft Allis-Chalmers scrubber, shown in Fig. 2, which has been in service since May 1944. Throughout the life of the galena operation, delivery of extremely muddy ore to the mill overloaded the medium cleaning system, and it frequently was necessary to cut off the feed and clean the medium for several hours until its normal viscosity had been re-established. The cleaning circuit

Jan 1, 1952

By A. T. Miesch, L. B. Riley

An error occurred in the preparation of Fig. 3, p. 249, of Basic Statistical Measures Used in Geo-chemical Investigations of Colorado Plateau Uranium Deposits. This figure shows the relation of the arithmetic mean: geometric mean ratio to the geometric deviation. Curves for the cases where n, the number of samples, is 100, 10, and 5 are too high with respect to the ordinate. The error is negligible at low geometric deviations, but becomes increasingly greater wi,th higher values of geometric deviation. Arithmetric mean values in Table I1 are not effected by the errors in Fig. 3. The authors will endeavor to supply copies of the revised curves on request; write to: A. T. Miesch, Geologist, Branch of Radioactive Materials, U.S. Geological Survey, Bldg. 25, Federal Center, Denver 25, Colo.

Jan 1, 1962

By H. LeRoy Scharon, A. B. Cleaves

THE application of geophysical techniques in the A engineering surveys of the Philadelphia and Western Extensions of the Pennsylvania Turnpike System is unique inasmuch as this is the first time, (to the authors' knowledge), that such studies have been employed on a large scale on a major highway system. These investigations were confined to specific areas along the center line of the proposed Philadelphia Extension between Carlisle and King of Prussia, and the Western Extension between Irwin and the State line near Youngstown, Ohio, as shown in Fig. 1. Along the 100 miles of the philadelphia Extension, the geophysical surveys were confined to 137 individual cuts and comprised a total length of 37.4 miles of line. The Western Extension, 66 miles in length, has 108 individual cuts. The accumulated length covered by electrical resistivity studies was 17.3 miles. The depth of the cuts varied from a minimum of 10 ft to a maximum of 62 ft. The geophysical investigations were made for the purpose of determining depths to bedrock in the 245 proposed cuts and at the sites of various structures. The 'data also served as a basis for geological interpretations of the condition of bedrock, contact zones, rock types, water table, and other factors significant in highway construction. The geophysical method of investigation employed the use of the electrical resistivity principle using the Gish-Rooney type electrical resistivity meter and the Wenner electrode configuration.* Apparent resistiv- ities were determined for constant intervals to various depths and were correlated with surface geological observations and subsurface geological conditions revealed by key diamond drill holes situated within a given cut interval. From these correlations, depths to bedrock were postulated with notations on other geological features that might be pertinent to modern highway construction. Geology The bedrock underlying the areas of the extensions of the Turnpike afford an excellent academic study of the electrical resistivity depth method as well as a practical application to modern highway engineering. The rocks encountered on the Philadelphia Extension vary in age from pre-Cambrian to Triassic and Quaternary, whereas in the Western Extension, bedrock is confined to relatively flat-lying strata in the Allegheny, Conemaugh, and Monongahela formations of the Upper Paleozoic, Pennsylvanian. Glacial and Recent stream, valley, and terrace deposits are common. Philadelphia Extension The oldest bedrock encountered in this extension are igneous and metamorphic. These, encountered chiefly in Chester County, consist of the strongly

Jan 1, 1952

[ARIZONA Established July 10, 1915 CHARLES R. KUZELL, Chairman GILBERT C. DAVIS, First Vice-Chairman ALBERT MENDELSOHN, Second Vice-Chairman MORRIS G. FOWLER, Secretary-Treasurer Phelps Dodge Corporation, Douglas, Ariz. LYLE M. BARKER P. D. I. HONEYMAN A. T. BARR H. M. LAVENDER T. G. CHAPMAN WALTER C. LAWSON GEORGE M. COLVOCORESSES W. H. LOERPABEL EDWIN H. CRABTREE, JR. CARL F. MILLS WALTER I. GARMS P. M. MOSIER WESLEY P. Goss J. A. RICHARDS 11. C. HENRIE JOSEPH A. WILCOX C. F. WILLIS]

Jan 1, 1946

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment, these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In U.S. Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center's 900-lb per hr pilot plant, approximately 85% of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to 51000 ppm equivalent SiO*, while maintaining a Ca(II) content of =16 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water. Water quality is perhaps as important to flotation as are the reagents used. The character of water is extremely variable, depending on whether the source is a well, lake, or stream, upon the season and temperature, upon prior use, and upon the character of the watershed. All of these factors influence the water hardness and the quantity of other dissolved inorganic salts, turbidity, dissolved and suspended organic matter, dissolved gases, and pH. Frequently, the differences in water quality can measurably influence flotation selectivity, often to the point of spelling success or failure. Water hardness is particularly troublesome in flotation systems employing fatty acids, but other unrecognized constituents may also contribute to peculiarities in flotation behavior. Furthermore, a given water source may be entirely satisfactory in one flotation system, but entirely inappropriate in another. In recent years, society has given more attention than formerly to water use, even in areas where water is plentiful. However, both the demands of a growing population, with increased per capita needs, and also those of industry must be met. As a result, riparian rights must be negotiated with the appropriate government agency or agencies so that consumption of water is often allocated or otherwise controlled. Furthermore, the disposal of off-process industrial and domestic water is coming under the increasing scrutiny of these same governmental units. In these respects, the mineral industry is no exception, so that conservation, water reclamation, and reuse may be expected to assume increasing importance. In 1932, it was stated that, "water reclamation is generally more expensive than the economy in water and reagents resulting from its use. It is employed only if it is urgent to save water."' The economic aspects of this statement may still be true, but the unrestricted use of water is becoming less and less an option of the user. The purpose of this paper is to discuss an investigation conducted by the U.S. Bureau of Mines (USBM), in which water reclamation and treatment were undertaken to develop procedures for, and to assess the effects of, water reuse on the flotation treatment of nonmagnetic taconites. This investigation is a logical extension of previous work described by the author and associates at the Twin Cities Metallurgy Research Center employing selective flocculation-desliming and anionic flotation of silica from low-grade, nonmagnetic iron ores2,8 The requirements for the selective flocculation-de-sliming and the anionic flotation of silica processes determined the direction of the investigation. Previous studies had indicated that pH levels of about 11.0 and 11.8 were required for selective flocculation and flota-tlon, respectively. The calcium content of the water was believed to be of importance in both of these operations, and since Minneapolis tap water with a Ca(I1) content of about 16 ppm had been successfully used, an attempt was made to reclaim the process water at an equal level of dissolved calcium. Additionally, the objective was to nullify or effectively limit the effects of dispersants and fatty acid residuals from prior stages of processing. Last but not least, the system of water treatment had to have the capability of reducing turbidities to workable levels. With about half of the effluent being derived from the selective flocculation-desliming step and carrying about 25,000 ppm of highly dispersed, suspended fines, this last objective appeared formidable at the outset. Procedures for water reclamation were derived, in part, from well-known mineral dressing practices, from past observations and investigations, and from concepts contained in various pertinent publications on water treatment."c These procedures involved: 1) flocculation with lime and poly electrolyte-type flocculants, 2) lime-soda-ash softening, 3) chemical precipitation, and 4) mineral surface adsorption. Control was exercised at various stages of water reclamation by frequent measurements of Ca(11), pH, and turbidity.

Jan 1, 1971

By E. C. Pechin

THE Lucy furnace, owned by Messrs. Carnegie, Kloman & Co., and located on the Alleghany River, on the outskirts of Pittsburgh, is a splendid modern furnace, 75 feet high, and 20 feet bosh. She had been working well on low grade ores of about 50 per cent., producing daily 68 to 75 tons. There was on stock 500 tons of Republic ore, one of the purest and best of the Lake Superior ores, averaging over 68 per cent. of iron, which had been procured for the purpose of making a trial for Bessemer iron. This was charged by itself, and Mr. Skelding, the founder, reports that he did not succeed in getting a single cast when it came down, before the furnace chilled from the hearth to the top of the boshes, some 25 feet. Every effort was made to save her, without avail, and the disagree-

Jan 1, 1874

By C. Upthegrove

DURING the past year considerable work dealing with physical properties of cartridge brass was done at the University of Michigan in cooperation with the Ordnance Department of the U. S. Army. This paper gives some of the data bearing on the effect of the anneal, previous to the final reduction or rolling, on the physical properties, particularly the hardness. Various phases of the subject of physical properties of cartridge brass have been presented by different investigators. Mathewson and Phillips1 refer to the work of Grard, in 1909, as the first systematic presentation of the relation between temperature-and time of anneal; changing of physical properties and microstructure, and the previous reduction by cold rolling. They discuss the relation between time and temperature of anneal and the previous reduction by cold rolling also; the relation between physical properties and grain size of annealed brass. The degree of deformation previous to the annealing was found to determine the temperature at which recrystallization and corresponding changes in physical properties would take place. Bassett and Davis,2 in establishing the relation between grain size and Brinell hardness; found the hardness for low-temperature annealing to be dependent on the previous degree of reduction, while for anneals above a certain temperature the hardness after the anneal was independent of the degree of reduction. Actual differences in hardness, due to the degree of reduction, disappear only on annealing at 600° C. or above; though the differences for metal subjected to different degrees of reduction and annealed at temperatures between 350° and 600° C. were found to be relatively small. In their determination of the relationship of grain size to Brinell hardness, Bassett

Jan 5, 1922

By W. H. Ode, W. A. Selvig

By plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Committee on Coal Classification. This scheme was sponsored by Subcommittee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as fo1lows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. The lignitic class of coal was divided into two groups both below 8,000 B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934

By A. N. Diehl

IT is the object of this paper (1) to deal with the elements in blast-furnace gas from the standpoint of their importance, and the part they are to play in future consumption, and (2) to give detailed information about the construction and operation of a plant designed among the first in this country for washing gas on a large scale.

Jan 5, 1914