Search Documents

By R. Simon, L. Yarborough

This paper presents a correlation for predicting the critical pressures of gas-solvent-reservoir oil systems of the type encountered in gas and solvent injection processes. Experimental data from 14 systems were used to develop the correlation which expresses critical pressure as a function of composition, C7+ mol weight, and C7+ characterization factor. Critical pressures predicted by the correlation for the 14 gas-solvent-reservoir oil systems have an average deviation of 2.8 per cent of the experimental values. The correlation war used to study a wide variety of other hydrocarbon mixtures reported in the literature whose critical conditions are in the range of interest in oil recovery work (100 to 280F and 2,000 to 6,000 psia). Critical pressures predicted by the correlation had an average deviation, expressed as per cent of experimental value, of 5 per cent for 20 miscellaneous mixtures from the literature, and 6.4 per cent for I7 methane-butane-decane mixtures reported by Sage and Lucey. INTRODUCTION Predicting critical points of hydrocarbon mixtures is an important part of phase behavior calculations. If the critical point can be predicted for a specific mixture, the separation between the bubble-point and dew-point regions will be defined, and physical properties of the mixture can be calculated by using the principle of corresponding states. Numerous correlations for predicting critical points of hydrocarbon mixtures have been published. Six of these correlationsl-8 were for light hydrocarbons, and two correlations7,8 ere for high boiling-point petroleum distillates. Organick9 And Eilerts" presented correlations which combined the published data from both light and heavy mixtures, and these correlations became the only available methods for predicting critical pressures for wide boiling range mixtures. In the course of the authors' work on secondary recovery by gas and solvent injection, experimental data were obtained for 14 mixtures of dry gas, ethane-propane-butane solvents, and various reservoir oils. The critical pressures and critical temperatures of these gas-solvent-reservoir oil systems were in the range of 1,900 to 4,800 psia and 180 to 265F. The critical pressures predicted for the 14 mixtures by the correlations of Organick and Eilerts had an average deviation from the measured values of about 13 per cent. The authors felt that it was necessary to develop a better correlation for engineering calculations and the resultant correlation, which is presented on Figs. 1 and 2, predicts the critical pressures of the 14 mixtures with an average deviation of 2.8 per cent. The validity of the correlation was tested by applying the correlation to other hydrocarbon mixtures reported in the literature. This subject is discussed later in the paper. The authors feel that there is also a need for an improved critical temperature correlation for gas-solvent-reservoir oil systems. However, developing a critical temperature correlation is a significant study in itself and is not included in this paper. EXPERIMENTAL DATA The compositions and critical points obtained by the authors for 14 gas-solvent-reservoir oil mixtures are shown on Table 1. The methane concentrations in these mixtures varied from 20 to 63 mol per cent. The intermediate hydrocarbon group, consisting of ethane, propane, and butane, varied from 20 to 64 mol per cent, and the concentration of the C,, fraction from 10 to 20 mol per cent. The physical properties of the C,, fraction covered the range from light, paraffinic, nonasphaltic (Mixtures 5, 6, 7, 8, 9 and 10) to heavy, aromatic, and asphaltic (Mixtures 13 and 14).

By R. W. Heckel, R. A. Tanzilli

Treatment of the finite, diffusion-controlled, two-phase, moving-interface homogenization problem has been carried out by numerical methods for a wide range of input parameters. Solutions have been obtained for planar, cylindrical, and spherical diffusion geometries. The effects of parameters such as the interdiffusion coefficients (concentration-independent) of- both phases, the concentrations (time-independent) of each phase at the interlace, mean composition, initial size of the dissolving- phase, and initial composition of- the two phases are considered. The results are displayed to show both the position of the interjace and the degree of homogenization (expressed in terms of concentration at the matrix phase symmetry boundary) as a function of diffusion time. Typical exaw~ples to which the results may be applied are discussed. A limited number of exact, closed-form solutions to the multiphase, diffusion-controlled, moving-interface problem exists in the literature, e.g., Refs. 1 to 7. The exact, closed-form solutions generally consider the outermost phases to be infinite in extent and also assume an interfacial velocity function. It is through use of such boundary conditions that closed-form solutions are readily obtained. An extensive literature also exists on numerical solutions to the mathematically analogous solidification problem, e.g., Refs. 8 to 12. In addition, a numerical solution involving mass transfer with spherical interfaces and infinite boundaries has recently been carried out.13 A practically important class of diffusion problems exists, however, in which the boundaries of each phase away from the interface are finite. For example the finite boundary condition arises when one sets up a model for analyzing the homogenization behavior of two-component powder compacts in two-phase systems or for studying the solution behavior of precipitates. Although exact, closed-form solutions have as yet not been found to this class of problems, solutions are possible using numerical methods. The purpose of this paper is twofold: 1) to describe a numerical method for treating the two-phase, diffusion-controlled, moving-interface problem involving finite boundaries with planar, cylindrical, and spherical interfaces; 2) to present the results of a parametric study which identifies the role played by each variable appearing in the analytical model. R. A. TANZlLLI,Student MemberAIME,onleaveofabsence from the General Electric Co., Re-entry Systems Department and A. W. HECKEL, Member AIME, are Graduate Student in Materials Engineering, and Professor, Department of Metallurgical Engineering, respectively, Drexel Institute of Technology, Philadelphia, Pa. Manuscript submitted May 6. 1968. IMD MATHEMATICAL MODEL The three geometries analyzed are shown in Fig. 1. For each configuration a symmetry element is shown, across whose boundaries the mass transfer is zero. Mean composition, C, and the characteristic solute-rich phase half-thickness (or radius), 1/2, are the independent variables while the characteristic symmetry element half-thickness, L/2 (measured from solute-rich phase center to the matrix phase plane of zero mass transfer), is a dependent variable. The symmetry element for a planar interface accurately represents a real diffusion situation involving the stacking of symmetry elements of constant size. Because cylindrical and spherical symmetry elements of constant size cannot be stacked to fill space, the meaning of the dimension, L/2, for these situations may be considered in terms of the following approximations: and where NA is the number of parallel cylindrical elements per unit area on a surface normal to the cylinder axes and Nv is the number of spherical elements per unit volume. The model consists of a solute-rich phase matrix phase composite of limited mutual solubility. The concentrations at the interface are assumed constant with time; no assumption of local equilibrium at the interface is necessary except for the case where the

Jan 1, 1969

Executive HENRY A. BUEHLER, Chairman ERLE V. DAVELER EDGAR RICKARD JOHN M. LOVEJOY WILLIAM WRAITH J. V. W. REYNDERS, Consultant Finance HENRY KRUMB, Chairman E. E. ELLIS PAUL D. MERICA H. G. MOULTON, Consultant Admissions RALPH M. ROOSEVELT, Chairman GEORGE D. BARRON DONALD M. LIDDELL WILBER JUDSONW. D. B. MOTTER, JR.

Jan 1, 1934

By W. W. Svendsen, J. F. Hoffmeister, W. C. Larson, R. E. Cozad

The paper presents the background, history, and current development of the retractable core bit for the wireline drilling system. Design criteria, concept development, and system design of the retractable bit system are discussed, including laboratory test results.

Jan 1, 1983

By J. P. Hammond, C. J. Sparks, C. J. McHargue

IN a study of the effects of solid solution alloying on the deformation texture of titanium, an alloy containing 3.8 pct A1 was found to develop a (0001) [1010] texture instead of the texture characteristic of pure titanium.ls2 A short investigation has been made of the change in texture with aluminum content. Alloys containing 0.27, 0.47, 1.05, and 1.43 pct A1 were prepared by vacuum arc melting, using iodide titanium as the base material. Homogenized ingots were reduced 90 pct in thickness by cold rolling. Pole figures were obtained using the usual film techniques. Fig. 1 shows that the change from the tilted to the nontilted (0001) position is gradual. The dashed contour lines in Fig. 1 indicate the extent to which data was collected. The addition of 0.27 pct A1 resulted in a decrease in the transverse spread of basal poles. With increasing aluminum content, the amount of the tilt becomes less and the region of highest intensity takes the shape of a ring about the center of the pole figure. For aluminum contents greater than 1 pct, the (0001) [1010] texture is definitely present—the sharpness increasing as the amount of solute is increased.* It is interesting to note that Williams and Eppel-sheimer9 eported for commercial grade titanium a high intensity region 20" toward the rolling direction from the rolling plane normal in addition to. one 30" toward the transverse direction. Their basal pole figure was similar to Fig. 1, row inree. The observation that the texture changes gradually with solute concentration is similar to the results of similar studies on copper." At the present time these effects are not clearly understood. Acknowledgments This work was sponsored by the Aeronautical Research Laboratory (WCRRL), Wright Air Development Center, under Contract NO. AF' 33(038)-19574. The authors are grateful for the aid received and permission to publish these results.

Jan 1, 1958

New Jersey Zinc Co. - The Plants Canon City Palmerton Depue

Jan 12, 1953

Jan 1, 1969

NEW MEMBERS The following list comprises the names of those persons who became members during the period Sept. 10, 1916, to Oct. 10, 1916. BLOOMFIELD, EDWIN CHARLES, Min. Engr., 1012 Standard Bank Bldg., Vancouver, B. C., Canada. BRINGS, HENRY, Min. and Met. Engr., Chief Engr., and Geol., Mollet-Mesrine, 1212 Mills Bldg., El Paso, Texas. CHASE, MARCH F., Vice-Pres., Commercial Acid Co., 1906 Boatmens Bank Bldg., St. Louis, Mo. CUMMINGS, ALVIN M., Asst. Mine Supt., Witherbee, Sherman & Co., Inc., Mineville, Essex Co., N. Y. DOUGLASS, GEORGE M., Genl. Safety Inspector, Amer. Smelt. & Ref. Co. 120 Broadway, New Fork, N. Y. EMRICH, CLARENCE T., Chief Chemist, Old Dominion Copper Min. & Smelt. Co., Box 1163, Globe, Ariz. GARDANIER, SUTTER ALBERT, Assayer, Mgr., Douglas Assay Co., Douglas, Cochise Co., Ariz.

Jan 10, 1916

By R. S. Goodrich, G. S. Ansell

The microstructure of three Al-Al2O3 SAP-Type alloys (containing 2.0, 3.0, and 5.7 wt pct alumina, respectively) was studied utilizing transmission electron microscopy. These alloys were fabricated from aluminum powders by powder-metallurgical techniques, cold-rolled into thin strips, and recrys -tallized. Thin foils suitable for an electron-transmission study were then prepared from the strip material by electropolishing. The microstructure of these alloys is shown to consist of small (0.1 mean diameter) plate -shaped alumina particles finely distributed in an aluminum matrix. In the higher-oxide content alloys the platelets are somewhat larger and more irregular in shape. The distribution of oxide particles is not uniform and there is an increasing tendency toward clumping SINCE the discovery by Irmann1 that aluminum alloys produced by compacting, hot pressing, and extruding fine aluminum powders possess remarkable high-temperature mechanical properties, the Al-A12O3 SAP-Type alloys have been utilized extensively as model dispersion-strengthened alloys in both experimental and theoretical invest igations.2-8 The use of the SAP-Type alloys as model dispersion-strengthened alloys implicitly assumes that their microstructure has been completely delineated. This is, however, not the case. with increasing oxide content. In all the alloys studied, the mean center-to-center spacing of particles was quite small (0.2 u) due to the very fine oxide debris present. Selected-area diffraction of the specimen identified the oxide as either y Al2O3 or y' Al2o3. The re crystallized MD-5100 alloy exhibited a mean grain diameter of only 0.7u, while the grain size of the other alloys was several hundred microns. Severe pinning of the grain boundaries by oxide particles was rarely observed, and the grain boundary triple points in the small-grained MD-5100 alloy were often particle -free. Diffraction contrasts visible around the particles are attributed to elastic strain fields set up by differential thermal contraction during cooling from the recrystallization anneal. Early investigation demonstrated that optical metallography did not possess sufficient resolution to observe the microstructure of the SAP-Type alloys.' Later, extensive use was made of replication techniques to study the microstructure by means of electron microscopy.7-9 These studies indicated that the SAP-Type alloys consist of a dispertion of irregular Al2O3 platelets, approximately 150A thick 9 and a micron or so on edge,9 distributed in a matrix of commercial-purity aluminum. These oxide platelets tend to be oriented in the aluminum matrix, with their largest dimension parallel to the extrusion direction. 8,9 A study employing polarized-light techniques1' indicated that the grain size of a series of as-extruded SAP-Type alloys was several microns in diameter, while the grain size after re-crystallization was several millimeters in diameter. A more recent study 12 utilizing surface-replication techniques examined the particle morphology,

Jan 1, 1964

By Earle Schumacher

COPPER-CALCIUM alloys are of interest as materials for use in deoxidized conductors of high conductivity. That calcium is effective in deoxidizing and degasifying copper is well known. Brandenberg and Wiens1 have described the use of calcium in the casting of sound copper and state that the deoxidation can be carried out without difficulty. The castings that they prepared were sound and sufficiently ductile to permit wire drawing. Pratt,2 in British Patent No. 1699 (1907), has claimed the use of calcium for the deoxidation and degasification of copper. Masing3

Jan 1, 1929

By Fred J. Hurst

In 1934, Irvin Lavine (A), University of North Dakota, stated that the low-rank coals (lignite and subbituminous) of this country represent a vast tonnage of fuel of commercial value and predicted that some day they will play an important role in our economic welfare. Lavine also pointed out that one of the major problems with efficient utilization of the low-rank coals is their high moisture content. Following the discovery of uranium-bearing lignite in the Williston basin of North and South Dakota in 1948 by D. G. Wyant and E. P. Beroni, detailed investigations were conducted (primarily during 1950 to 1954) by members of the U. S. Geological Survey to evaluate the geologic factors and economic possibilities of the radioactive lignites as a source of uranium. The information gained in these studies and summarized in several papers indicated that a large potential reserve of uranium is contained in the subbituminous coal and lignite deposits of the Dakotas and Wyoming (2,3,4). Most investigators concluded that an epigenetic emplacement of uranium in the coal by means of circulating groundwater and the more extensive concentrations of uranium in coal are apparently related to the permeability of the rocks enclosing the coal beds. Breger (5) and others have shown that uranium is readily adsorbed by coal and is held irreversibly as a disseminated adsorbed constituent. Briefly, lignite beds containing 0.1 to 10% uranium have been discovered in the Dakotas and Wyoming. The distribution of uranium was found to be erratic and was usually concentrated in thin layers, which were characteristically 10 to 14 in. thick and occasionally 30 to 36 in. thick. Lignite beds more than 3 ft. thick generally contain more uranium at the top of the bed than at the bottom. Special strip mining techniques are required to mine these thin

Jan 1, 1983

By Lane D. Schultz, John D. McLennan, Jean-Claude Roegiers

During construction of the intake tunnels for a nuclear power facility in Ohio, evidence of a potential geological discontinuity was discovered. Assuming that the discontinuity might still prevail underneath the site, it was decided to measure the stress profile across the discontinuity. This information would be used to assess future stability on the basis of predicted shear stresses acting along the fracture. Seven intervals were hydraulically fractured to determine the magnitude and orientation of the stress tensor, in order to infer the shear stresses acting along the discontinuity. The formation consists of tightly interbedded shales. This, in combination with the shallow depths, would be expected to lead to horizontal hydraulic fractures -- a situation which generally provides limited information. Careful testing procedures, and meticulous interpretation, allowed the determination of the horizontal stress components as well as the vertical component, via the initiation and/or propagation of multiple fractures. The measured stresses fall within the range of stress magnitudes and orientation determined in other areas of the northeastern and north-central United States and in southern parts of Canada. In addition, a small stress gradient anomaly was recorded at depth. On a different scale, the measured stress regime is also evaluated in light of the regional geological setting.

Jan 1, 1982

By Carl F. Cline, Richard R. Vandervoort, Willis L. Barmore

THE objective of this investigation was to determine the high-temperature plastic deformation behavior of stoichiometric uranium mononitride as a function of stress and temperature. Interest in the properties of this material stems from its potential use in high-temperature nuclear reactor systems. The creep of other refractory compounds containing uranium (e.g., U02, UC) has been studied by various investigators.1"4 Fassler et al.4 have studied the creep of UN in vacuum from 1100° to 1350°C at stresses of 6000 and 8000 psi. In the present work, the creep of stoichiometric UN was investigated from 1500° to 1800°C at stresses from 2000 to 5000 psi in a partial pressure of 200 mm of nitrogen. The specimens were prepared by hot isostatic pressing of UN powder into cylinders of $ in. diam by about 1 in. high. After pressing, the specimens were heat-treated in nitrogen at 1900°C for 50 hr. The densities of individual specimens were determined by the water displacement method. All specimens were theoretically dense, based on a value of 14.32 g per cu cm.5 Principal metallic impurities in ppm by weight were: Ca, 50; Cu, 5; Fe, 30; Mg, 5; Ni, 10; and Si, 20. Oxygen content was 400 ± 50 pprn and carbon content was 100 i25 ppm. The nitrogen content was 5.56 ±0.05 wt pct. The average grain size for five specimens, as determined by the intercept method, was 0.14 i 0.01 mm. One specimen had a grain size of 2.0 mm. This large grain size is an anomaly, since all specimens had the same chemical and thermal histories. Specimens of 1/4 in. diam by 1/2 in. high were creep-tested in compression in a clam shell furnace heated by W-25 pct Re sheet elements. Temperature was measured to ilODC by an optical pyrometer which had been calibrated by a standard source. The distance between fiducial marks on the specimen was measured before placement into the furnace. The furnace chamber was evacuated to 10-5 Torr and back-filled to 200 mm N2. After heating rapidly to temperature, the load was applied and controlled to ±2 pct by an Instron testing machine. Upon initial loading, the specimen was deformed until a constant crosshead rate was obtained, then quenched to room temperature, remeasured, and replaced in the furnace. Upon subsequent reloading at temperature, the crosshead rate was constant for the selected condition indicating steady-state creep.

Jan 1, 1969

By Richard Pearce

H. M. Howe, Boston, Mass. (Communication to the Secretary): One by one our venerated idols are shattered, our cherished beliefs are filched away. Mr. Pearce's interesting experiments on the effect of an intermixture of coal in expelling arsenic from roasting copper-ores seems at the first blush to spike one of the great cannons of our faith. Plattner, however, is so positive that coal does lead to the expulsion of arsenic that we may well pause before accepting Mr. Pearce's results as final, and ask whether there is not some explanation of the discrepancy between them and Plattner's statements. Plattner states that while ferric arseniate decomposes easily under the action of carbonaceous matter with expulsion of arsenic as arsenious oxide (As2O3) and sub-oxide of arsenic (it is now generally thought, I believe, that this supposed sub-oxide is really but a mixture of metallic arsenic and arsenious oxide); cupric arseniate, on the other hand, undergoes this decomposition with difficulty, usually forming a certain proportion of arsenide of copper. Now, may not the whole matter lie just here? Mr. Pearce experimented on an ore containing its arsenic as enargite, sulph-arsenide of copper. This, in roasting, would probably give rise to arseniate

Jan 1, 1890

COUNCIL OF SECTION DELEGATES Nicholas A D'Arcy, Jr, Chairman (Southern California Section) Charles Chapman, Vice-Chairman (Florida Section) Ben H Parker, Secretary (Colorado Section) Frontier Refining Co Boston Bldg Denver 2, Colorado

Jan 1, 1956

By James A. Carney

The quality of water for steam boilers is a serious question in Illinois, and has been the occasion of many investigations, undertaken either for the discovery of sources of a better supply, or for the purification of the supplies already at hand. LOCATION OF SUPPLIES. The sources of supply of which this paper treats lie along the right of way of the Chicago, Burlington and Quincy Railroad Company, and form a nearly straight line from Chicago, Illinois, on Lake Michigan, to Burlington, Iowa, on the Mississippi River. The supplies consist of surface-, ground- and deep well-waters ; their locations are given in Fig. 1, which is adapted from a map of Illinois published by the Illinois Railroad Commissioners. The influence of the geological formation on the water-supply of Illinois is fully treated in an article in the Seventeenth Annual Report of the U. S. Geological Survey by Mr. Frank Leverett, entitled, " The Water-Resources of Illinois." It is not the purpose of this paper to introduce a geological discussion; and

Jan 1, 1898

By J. M. Lohr

A COMMERCIAL development requiring a suitable alloy or alloys for sealing into various grades of glass made it desirable to have a more exact knowledge of the expansion characteristics of the nickel-iron alloys than appeared in the published literature. The expansion of the more common. FIG. I.-EXPANSION CURVES OF SEVERAL FIG. 2.-EXPANSION CURVES OF TWO TYPES OF GLASS. (Courtesy of R. C. A.) TYPES OF GLASS. (Courtesy of R. C. A.) types of glass under consideration varies from 2.7 to 10.4 X 10-6 per degree Centigrade, over the range 20° to 400° C. For reference, the thermal expansion curves f several types of glass used for sealing by the lamp and tube industries are given (Figs. 1 and 2). This paper covers a detailed investigation of the thermal expansion of a series of nickel-iron alloys in which the nickel content varies from 30 to 70 per cent. Particular stress is laid on the alloys that contain between 40 and 55 per cent Ni.

Jan 1, 1938

By W. C. Winegard, E. L. Holmes

The effects of the solute elements lead and bismuth on grain growth in zone -refined tin have been investigated. At low temperatures, viz. below 160°C. or at high concentrations, viz. greater than 0.03 at. pct, the temperature dependence of grain growth was found to be constant. A correlation was found to exist between the rates of grain growth in the presence of solute impurities and the factor [C Ir - 1]2 , where C is the solute concentration, r is the radius of solvent atom, and r' is radius of solute atom. It is shown that the Liicke and Detert theory does not give a satisfactory explanation of the results obtained. INVESTIGATIONS of grain growth in zone-refined lead and tin and some effects of solute elements on grain growth in these metals have been reported by Bolling and winegardly2 and Holmes and winegard? The present investigation is an extension of the previous work, and was undertaken to provide additional results which might make it possible to discover the mechanism whereby the rate of grain growth is affected by the presence of foreign solute atoms. The experimental procedure was exactly the same as that described previously.3'4 Figs. 1 and 2 show the results obtained with lead and bismuth additions over the same temperature range, viz. 167" to 220°C, as that used for the investigation of grain growth in zone-refined tin.3 Fig. 3 shows the results obtained for zone-refined tin and for this tin with lead solute additions over an extended temperature range. DISCUSSION OF RESULTS As mentioned previously,3 the character of grain growth in the particular zone-refined tin used in these experiments appears to change as the temperature of annealing falls below about 160°C. The grain growth became somewhat irregular and was characterized by a jaggedness of many of the grain boundaries. The reason for this change is not known, but may be due either to residual impurity effects or possibly an oxide precipitation. It was obvious that normal grain growth only occurred in the zone-refined tin through the high-temperature range 167" to 220°C, and so the effects of solute atoms on grai11 growth over the two temperature ranges will be discussed separately. a) Effect of Impurity on Grain Growth in the Temperature :Range Above 167°C. It is apparent from Figs. 1 and 2 that, for low concentrations of solute, the rates of grain growth tend towards a common value as the melting temperature of tin is approached. As the concentration of lead is increased, the rate of grain growth close to the melting temperature is also reduced, and at high concentrations the temperature dependence of the rate of grain growth appears approximately constant. It should be noteil that the effect of bismuth is greater than that of the same concentration of lead, but both these solutes have a smaller effect on the rate of grain growth than silver, as seen from an earlier investigation of Holmes and Winegard. It should

Jan 1, 1962

By AIME AIME

AT a recent meeting of the Utah Section. A.I.M.E., P. D. Nielson, general plant superintendent of the new Geneva steel plant at Provo, Utah, spoke on "General Operations of the Geneva Plant." Mr. Nielson explained that the plant was located at Provo, Utah, on account of railroad facilities, the proximity of coal, iron, and limestone, and the nearness of water for operating the plant. Water probably was the most important item in making the decision.

Jan 1, 1944

By Jerome J. English, Gordon W. Powell

An experimental investigation and mathematical analysis of the thermal-dilation behavior of the titanium alloy Ti-7Al-3Cb have shown that the linear dimensional changes associated with the polymorphic transformation need not be isotropic. The absolute magnitude of the linear dimensional change, which may be either positiue or negative, associated with the cr-p transformation is dependent upon the relutzve volumes of different orientations of the transformation product. It is hypothesized that the dilation irregulati-ties that have been observed during the polymorphic transformation of pure, coarse-grained titanium and other titanium-base alloys can be explained in the same manner. When titanium is heated above about 165O°F, the hcp a structure transforms to bcc 0. Thermal-dilatioh measurements have shown that the transformation is accompanied by a decrease in length of 0.16 pct.' Such dilation behavior would be expected because the volume of the hcp unit cell is about 0.3 to 0.4 pct greater than that of the bcc unit cell. A recent investigation2 of the thermal-dilation behavior of an experimental a-p* titanium alloy, Ti- 7A1-3Cb, containing 0.06 wt pct 0 showed that its dilation behavior during the polymorphic transformation differed substantially from that reported for unalloyed titanium. The first time the alloy was cycled through the transformation, the dilation curve closely duplicated that of unalloyed titanium. However, upon repeated cycling through the transformation temperature range, both the magnitude and the sign of the dimensional change associated with the transformation were observed to vary with each cycle. This investigation was undertaken to obtain additional data on the dimensional changes associated with the polymorphic transformation in the Ti-7A1-3Cb alloy and to determine the cause of the dimensional irregularities. After testing, the specimens were examined metallo-graphically. In addition, Laue back-reflection patterns were obtained from selected sections taken perpendicular to the specimen axes to determine the a orientations present in these sections. White radiation from a tungsten target and a 0.1-mm-diam collimator were used to produce the diffraction patterns. RESULTS Dilation Curves. Three types of thermal-dilation curves were obtained when the a-8 titanium alloy was heated and cooled through the transformation temperature range. These three types of curves are illustrated in Fig. 1. The type I curve represents what is considered normal behavior, because the dilation change is what would be expected on the basis of the volumes of the unit cells of a and p. The Type I1 curve is the inverse of Type I. Normal behavior is characterized by an expansion on cooling through the transformation, whereas a contraction takes place in the Type 11 curve. With Type ni behavior, no clearly distinguishable length change occurs during the transformation. No other anomalies that might be indicative of other phase transformations were observed in the dilation curves at lower temperatures. Apparently, the cooling rate was low enough for equilibrium to be reached during the 0 to a transformation. Table I lists the types of dilation curves observed during the polymorphic transformation as a function of the direction of measurement and cycle number. The A1 value was determined by extrapolating the low-temperature (a + 5 pct p) and high-temperature (100 pct p) segments of the dilation curves to a common temperature and measuring the difference in the or-dinates at that temperature, see Fig. 1. The transformation occurs over a temperature range in this alloy, so the magnitude of A1 is not an absolute value but depends on the choice of temperature. A mean temperature, T,, within the transformation temperature range was selected for the measurement. T, on cooling occurred about 100°C lower than T, on heating. The first time each of the three dilation specimens was heated to above the temperature, that is, Cycle 2, normal Type I behavior was observed. In Cycle 3, two deviations from normal behavior occurred. First, during cooling of the longitudinal specimen, a substantially larger expansion, +0.21 pct, was measured as 0 transformed to a compared with +0.03 pct in Cycle 2. Second, the thickness specimen was observed to undergo a contraction instead of the anticipated expansion on cooling. Continued cycling of the three specimens from room temperature to 2500°F produced additional changes in the dilation behavior. These changes did not seem to be related to the fabrication direction of the alloy because the values of a1 for the longitudinal, transverse, and thickness specimens varied unpredictably in magnitude and sign. Furthermore, both the longitudinal and transverse specimens showed all three types of dilation curves at least once during the six cycles that they received. Fig. 2 is a sketch of the transverse specimen after

Jan 1, 1967