Search Documents

By K. L. Clark, Nicholas Kowall

MAXIMUM furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. WORK OF OTHER INVESTIGATORS In 1938, Burns, Moore and Archer published a curve7 that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the range found in constructional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only 0.20 per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E. 43xx steels. His procedure consisted of chill-casting a test bar that was large enough to give a surface that could be prepared for Brinell indentations. The test piece was quenched immediately after solidification was complete and hardness readings were taken, so that the carbon content could be read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. EXPERIMENTAL WORK Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By L. B. Slichter

IT has been estimated that rock exposures in most mining districts aggregate less than 1 per cent. of the total surface area.1 Conclusions concerning the hidden 99 per cent. necessarily have been based on knowledge of only a small fraction of the surface, and from this limited information the geologist has been obliged to deduce the approximate and general nature of the underlying formations. In the search for ore it is necessary to supplement this general picture with greater detail. Fairly accurate knowledge of relatively small zones is required. This knowledge is carefully sought in many different ways-detailed interpretations of geological history, the tracing of float, the use of test pits, of trenching, of drilling, and of other methods. Practical ingenuity, scientific brilliance, great perseverance and patience, and the expenditure. of large sums of money have all been a part of this search. The problem of exploring beneath cover with economy, and of obtaining essential information which this cover hides, is obviously a difficult one. It is also a very important one, for geologists inform us that already the story of the 1 per cent. exposed outcrops has been largely read.2 There remains the nearly virgin field comprised in the hidden 99 per cent., and the importance of this zone is bound to increase continually. In recent years, the problems connected with the exploration of this "99 per cent. zone" have attracted a constantly enlarging group of investigators and at present greater efforts than ever before are being made to resolve then. This work, in its various special aspects, has enlisted, beside geologists, the cooperative efforts of chemists, physicists, and mathematicians. The progress made in this development should be kept before those directing explorations in order that due advantage may be taken of a changing situation.

Jan 1, 1928

By W. P. Lass

The gold precipitate from the zinc-dust presses in the cyanide plant of the Alaska-Treadwell Gold Mining Co., Treadwell, Alaska, is treated, in the refinery adjoining, by the Tavener or lead-smelting method. About 3 or 4 tons of this precipitate is produced monthly having 'a gold assay value of $40,000 to $60,000 per ton. It was formerly the practice to treat the byproducts from this process, consisting of 2 tons of slag, 300 lb. of matte, 500 1b. of refinery refuse, flue dust, etc., in a 24-in. water-jacketed blast furnace. This practice was discontinued in the summer of 1914 by reason of the difficulty of keeping the lead-well open when treating a high-grade lead product; of preventing the loss of gold in the flue dust; and of avoiding injury to the general health of the refinery operators; a plain single-phase electric furnace was substituted for the blast furnace. The furnace was constructed from an old steel acid drum by cutting off the top and introducing a cable, made from strands of bare copper wire, through the bottom and spreading the strands out fan-shaped on the inside of the drum. Powdered graphite, obtained by grinding up old crucibles, mixed with 10 per cent. cement, was tamped wet into the bottom of the drum, around and completely covering the copper wires. The graphite was carried up to the bottom of the furnace, or lead-well, and acted as the lower electrode. The sides were built up of ordinary firebrick forming a melting chamber 14 in. in diameter by 20 in. high. The upper electrodes, of graphite or carbon, are 3 in. in diameter and 40 in. long, arranged with joints enabling new electrodes to be connected without shutting down or wasting stubs. A screw feed was arranged for raising and lowering the upper electrode. (Figs. 1 and 2.) The cover for the furnace had three openings, one for feeding the charge, one for the escape of gases, and one in the center for the introduction of the electrode. It was later found more practical to enlarge this center opening to 6 in. in diameter, to allow of a central feeding of the charge around the electrode.

Jan 1, 1916

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee. Each year the Nominating Committee is to select "official" candidates for eight places, as follows:, (1) President and Director (2) Vice-President and Director (3) Vice-President and Director (4) Director (5) Director (6) Director (7) Director (8) Director

Jan 1, 1939

By Zárate G. E.

Practical and statistical considerations concerned with the sampling, sample preparation and chemical analysis of precious metal ores are reviewed. The principal requirements related with the characteristics of sample cutter, sample preparation, equipment and methods are discussed. The main errors introduced in the different stages of the sampling systems are defined. The application of statistical techniques to evaluate these errors to determine the ore grade variation and to design the number of increments needed to get an accurate assay are presented. Finally, results obtained with the application of this method to gold and silver ores are analyzed and some recommendations are given.

Jan 1, 1984

By R. J. Evans, A. G. Revesz

Silicon films have been grown by chemical reaction on (111) silicon substrates. The surfaces were examined by various microscopic and interfero-metric methods. Surface structures are classified into two groups depending on whether the angles between the bounding planes and the (111) surface are small (<3 deg) or large (> I0 deg). A layer-gvowth mechanism is postulated to explain the topography and the influence of growth parameters. Growth proceeds by lateral expansion of the (111) layers in (211) directions, thereby forming steps. The step edges are perpendicular to the direction of expansion and are thus along (110) directions. Step bunching md surface nucleation both play an important role in modifying the flow pattern and in the step regeneration. These are influenced ver?) much by impurities, especially oxygen. Although the growth is a result of a surface-controlled ga: reaction, it is very similar to growth from an impure solution. OVERGROWTH ("epitaxial growth") of silicon is important and widely used. During the past years several investigators have observed various topographical features or so-called faults on the grown films. A study of the surface morphology gives some insight into the growth mechanism. I) EXPERIMENTAL Silicon films have been grown on silicon substrates by a method described by Theuerer.&apos; Silicon is formed by reduction of SiCl, in hydrogen. The rate of incidence of SiC1, was varied between 5 x 10"6 and 2 x 10&apos;4 moles min-&apos; cm-&apos;. The mole fraction of Sic4 in the Hz-SiCL mixture was about 5 x X Both the rate of incidence and the mole fraction were calculated on the assumption that the Hz bubbling through the SiC1, reached equilibrium saturation. Assuming uniform velocity distribution, the linear velocity of the gas in the reactor tube was estimated to be 2 cm sec-l. The temperature of deposition was varied between 1070" and 1260°C. Chemically polished p-type silicon wafers of 20 to 100 ohm cm resistivity were used as substrates. These were within 1/2 deg of a (111) orientation. The thickness of the grown n-type film was determined by two methods: a) measurement of the depth of the p-n junction taking into account the junction shift due to diffusion, b) measurement of the traces of stacking-fault tetrahedra on the (111) plane.&apos; The agreement between the two methods was better than 20 pct. The rate of growth varied between 0.2 and 4.0 pmin-&apos;. The formed films were examined by reflection and light-section microscopy, and by multiple-beam interferometry. Phase-contrast illumination revealed height differences of about 30A. For measuring heights greater than 1 p a light-section microscope3 was used. The resolution by multipke-beam interferometry4 was between 50 and 100A. Crystallographic directions on the surface were determined by X-ray and from the orientation of etch pits and stacking faults as revealed by Dash etch (I part HI?, 3 parts HNOJ, and 12 parts CH3COOH). Some specimens have been investigated by electron microscopy. Platinum-shadowing and carbon-replica techniques were used to show the fine topography and reflection diffraction to determine the structure of the grown layers. 11) RESULTS The topographical features can be classified into three groups. he first group is comprised of fine ridges (striations). The second group consists of structures, which are bounded by planes making angles of less than 3 deg with the (111) surface. They are, therefore, vicinal planes. Structures which closely resemble growth or etch pyramids from the third group would normally be bounded by perfect low-index crystallographic planes. In this case they are deformed. The angles between the bounding planes and the (111) surface are generally larger than 10 deg. The fine ridges are present, even on the smoothest surfaces, as shown in Fig. 1. They are along a (110) direction. The height differences could not be resolved with interferometric techniques. The basic characteristic structures of the second group are depressions and hillocks. These are bounded by three planes, two of them with larger slopes than the third one. The edges between the planes, as projected to the (111) surface, point in (211) directions. Various habits of these structures are shown

Jan 1, 1964

Some Things We Don&apos;t Know about the Creep of Metals. By H. W. Gillett (T.P. 1087) Reduction of Iron Ores under Pressure by Hydrogen. By Michael Tenenbaum and T. L. Joseph (T.P. loll, with discussion) Induction Furnaces for Rotating Liquid Crucibles. By E. P. Barrett, W. F. Hol- bRook and C. E. Wood (T.P. 986, with discussion) Mechanism of Solidification and Segregation in a Low-carbon Rimming-steel Ingot,. By Anson Hayes and John Chipman (T.P. 988, with discussion) Solidification of Rimming-steel Ingots. By A. HultGRen and G. PhRagmen. (Contribution 112) Dendritic Structure of Some Alloy Steels. By Daniel .I. Martin and James L. Martin (T.P. 1066, with discussion) Occlusion and Evolution of Hydrogen by Pure Iron. By George A. Moore and Donald P. Smith (T.P. 1065, with discussion) Structure of Iron after Con~pression. Hy Charles S. Barrett (T.P. 977, with discussion) Structure of Iron after Drawing, Swaging, and Elongating in Tension. Ry Charles S. Barrett and L. H. LevensoN (T.P. 1038, with discussion) Magnetic Torque Studies of the Texture of Cold-rolled and of Recrystallized Iron-silicon Alloys. By Leo P. TaraSovJ(T.P. 1012, with discussion) Influence of Atmosphere and Pressure on Structure of Iron-carbon-silicon Alloys. By Alfred Boyles (T.P. 1046) Kinetics of the Decomposition of Austenite at Constant Temperature. By J. H. Austin and R. L. Rickett (T.P. 964, with discussion) Reaction Kinctics in Processes of Nucleation and Growth. By William A. Johnson and Robert F. Mehl (T.P. 1089, with discussion) Phase Changes in 3.5 Per Cent Nickel Steel in the Acl Region. By I. N. Bavarine (T.P. 1031, with discussion) Chromium in Structural Steel. By Walter Crafts (T.P. 1055) Surface Allotropic Transformation in Stainless Steel Induced by Polishing. By J. T. BuHwell and J. WUlff (T.P. 1032, with discussion) Nature of :Passivity in Stainless Steels and Other Alloys, I and 11. Ry H. H. Uhlig and John WUlff (T.P. 1050, with discussion) Thermal Expansion of Nickel-iron Alloys (Nickel from 30 to 70 Per Cent). Ry J. M. Lohr and Charles H. Hopkins (T.P. 987, with discussion) Low-temperature Transformation in Iron-nickel-cobalt Alloys. By L. L. Wy~Ian (T.P. 1013, with discussion) Fracture of Steels at Elevated Temperatures after Prolonged Loading. By R. H. Thielemann and E. R. Parker (T.P. 1034, with discussion)

Jan 1, 1939

Some Things We Don&apos;t Know about the Creep of Metals. By H. W. Gillett (T.P. 1087) Reduction of Iron Ores under Pressure by Hydrogen. By Michael Tenenbaum and T. L. Joseph (T.P. loll, with discussion) Induction Furnaces for Rotating Liquid Crucibles. By E. P. Barrett, W. F. Hol- bRook and C. E. Wood (T.P. 986, with discussion) Mechanism of Solidification and Segregation in a Low-carbon Rimming-steel Ingot,. By Anson Hayes and John Chipman (T.P. 988, with discussion) Solidification of Rimming-steel Ingots. By A. HultGRen and G. PhRagmen. (Contribution 112) Dendritic Structure of Some Alloy Steels. By Daniel .I. Martin and James L. Martin (T.P. 1066, with discussion) Occlusion and Evolution of Hydrogen by Pure Iron. By George A. Moore and Donald P. Smith (T.P. 1065, with discussion) Structure of Iron after Con~pression. Hy Charles S. Barrett (T.P. 977, with discussion) Structure of Iron after Drawing, Swaging, and Elongating in Tension. Ry Charles S. Barrett and L. H. LevensoN (T.P. 1038, with discussion) Magnetic Torque Studies of the Texture of Cold-rolled and of Recrystallized Iron-silicon Alloys. By Leo P. TaraSovJ(T.P. 1012, with discussion) Influence of Atmosphere and Pressure on Structure of Iron-carbon-silicon Alloys. By Alfred Boyles (T.P. 1046) Kinetics of the Decomposition of Austenite at Constant Temperature. By J. H. Austin and R. L. Rickett (T.P. 964, with discussion) Reaction Kinctics in Processes of Nucleation and Growth. By William A. Johnson and Robert F. Mehl (T.P. 1089, with discussion) Phase Changes in 3.5 Per Cent Nickel Steel in the Acl Region. By I. N. Bavarine (T.P. 1031, with discussion) Chromium in Structural Steel. By Walter Crafts (T.P. 1055) Surface Allotropic Transformation in Stainless Steel Induced by Polishing. By J. T. BuHwell and J. WUlff (T.P. 1032, with discussion) Nature of :Passivity in Stainless Steels and Other Alloys, I and 11. Ry H. H. Uhlig and John WUlff (T.P. 1050, with discussion) Thermal Expansion of Nickel-iron Alloys (Nickel from 30 to 70 Per Cent). Ry J. M. Lohr and Charles H. Hopkins (T.P. 987, with discussion) Low-temperature Transformation in Iron-nickel-cobalt Alloys. By L. L. Wy~Ian (T.P. 1013, with discussion) Fracture of Steels at Elevated Temperatures after Prolonged Loading. By R. H. Thielemann and E. R. Parker (T.P. 1034, with discussion)

Jan 1, 1939

By M. H. Mueller, P. A. Beck, W. P. Chernock

HARRIS introduced the term inverse pole figure for the diagrams previously used by Barrett&apos; to represent the volume fraction p(a,ß) of material in various orientations with respect to the fiber axis in a specimen with fiber texture. The direction of the fiber axis with respect to the crystal lattice is specified by the two independent angle variables a and ß. In such a diagram p gives the fiber axis density distribution over the various crystallographic directions. The p(a,ß) may be given in a two-dimensional diagram by means of contour lines (p=con-stant) in a stereographic projection. The inverse pole figure incorporates in a single contour line diagram all the information given conventionally in pole charts for various (hkl) reflections and, therefore, it represents a considerable degree of condensation. Also, it gives this information directly in terms of the volume fraction of the specimen in various orientations, and it obviates the necessity of referring back and forth between the various pole charts in an attempt to interpret them in terms of orientations. Inverse pole figures undoubtedly represent the most adequate method for describing a texture in a quantitative manner and, at least in the case of fiber textures, this method is certainly a practicable one. Harris described1 a simple procedure for determining at least the rough outlines of a quantitative inverse pole figure. This method depends on the measurement of the intensity of X-ray reflections from various (hkl) planes lying parallel to the same specimen surface. In the case of a rod, reflections from a plane specimen surface perpendicular to the rod axis (fiber texture axis) are to be used. Harris has shown that the measured intensities I,,, reflected by crystal planes (hkl), aligned perpendicularly to the fiber axis of a specimen with unknown fiber texture, and the corresponding intensity Iu nkl from a random specimen are related to the p(a,ß) value for the unknown texture by the following equation IAkl/I°Aklw=c/c°.p(a, ß) [1] where C and C° re parameters depending on the crystal imperfections (extinction), surface preparation (e.g., thickness of oxide layer), the absorption coefficient in the specimen, effective line breadth, and instrumental factors. The values of the variables a and ß1 defining the crystal orientation, depend only on the indices hkl of the reflecting plane perpendicular to the fiber axis. Since p, as described by Harris1, is normalized in such a way that upon integration over the total orientation range its mean value is 1, the parameter C/C may be calculated approximately by the summation of Eq. l over all available X-ray reflections hkl, corresponding to a set of discrete orientations (rather than by integration over the complete range of orientations represented by the continuous variables a and ß). From the summation of Eq. 1 1/n SI AKL/I° Akl = C/C. SP(a,ß)/n is obtained where, as stated above 2p(a,ß) =1. n Therefore

Jan 1, 1959

By Paul Weir

During the past decade, methods of producing bituminous coal in the state of Illinois, which ranks third in production among the states in which bituminous coal is mined, have undergone great changes. From less than one million tons in 1923, the strip-mine production has gradually increased to a high of 11,725,870 tons in 1937. From a negligible amount prior to 1927, the amount of coal mechanically loaded underground had increased to a high of 28,374,362 tons in 1937. The amount manually loaded in 1937 reached a low of 12,332,023 tons. In this same year, this state ranked first in strip-mine production, also in mechanically loaded production. For this reason a study of the influence of mechanization on location of production in Illinois may be helpful in anticipating what may happen in other producing states. The reason for the changes in methods lies in the differences in costs of production. The Bureau of Research and Statistics of the National Bituminous Coal Commission has made public the following costs of production by various methods in the state of Illinois (district 10) for the last nine months of 1937: all mines, $1.7602 per ton; strip mines, $1.4319; mechanical loading mines, $1.7457; hand loading mines, $2.1793; all underground mines, $1.8703. These are weighted averages for the entire district. Inasmuch as production in 1937 was reported from 58 counties scattered over two-thirds of the area of the state and from five different seams varying in thickness from less than 3 ft. to as much as 12 ft., it is apparent that the location of production must be influenced by the extent of mechanization possible in the various producing counties. SHIFT in Production The term "mechanization" is commonly used to designate the coal-loading operation. However, in a broader sense it embraces the use of any and all mechanical and electrical equipment on the surface and underground. Strip mining is an intensive form of mechanization. The mechanical cleaning of coal is a form of mechanization. Cutting machines and motor haulage likewise are forms of mechanization, hence

Jan 1, 1940

By Paul Weir

During the past decade, methods of producing bituminous coal in the state of Illinois, which ranks third in production among the states in which bituminous coal is mined, have undergone great changes. From less than one million tons in 1923, the strip-mine production has gradually increased to a high of 11,725,870 tons in 1937. From a negligible amount prior to 1927, the amount of coal mechanically loaded underground had increased to a high of 28,374,362 tons in 1937. The amount manually loaded in 1937 reached a low of 12,332,023 tons. In this same year, this state ranked first in strip-mine production, also in mechanically loaded production. For this reason a study of the influence of mechanization on location of production in Illinois may be helpful in anticipating what may happen in other producing states. The reason for the changes in methods lies in the differences in costs of production. The Bureau of Research and Statistics of the National Bituminous Coal Commission has made public the following costs of production by various methods in the state of Illinois (district 10) for the last nine months of 1937: all mines, $1.7602 per ton; strip mines, $1.4319; mechanical loading mines, $1.7457; hand loading mines, $2.1793; all underground mines, $1.8703. These are weighted averages for the entire district. Inasmuch as production in 1937 was reported from 58 counties scattered over two-thirds of the area of the state and from five different seams varying in thickness from less than 3 ft. to as much as 12 ft., it is apparent that the location of production must be influenced by the extent of mechanization possible in the various producing counties. SHIFT in Production The term "mechanization" is commonly used to designate the coal-loading operation. However, in a broader sense it embraces the use of any and all mechanical and electrical equipment on the surface and underground. Strip mining is an intensive form of mechanization. The mechanical cleaning of coal is a form of mechanization. Cutting machines and motor haulage likewise are forms of mechanization, hence

Jan 1, 1940

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

The object of this paper is to describe the adaptation of electrical resistivity measurements to the particular case of exploration in which the surface is an expanse of water (river, lake, sea). Water in itself does not constitute an obstacle to electrical exploration. It is merely an overburden, which is fluid instead of being solid, and as a consequence the routine of the measurements has to be modified. Also, in many instances, the liquid under consideration is highly conductive (salt water). This introduces an additional difficulty into exploration work, and has to be overcome by the geophysicist. We do not propose to discuss here the basic principles of electrical resistivity measurements, which have been dealt with in various previous papers,&apos; but will simply recall the two fundamental techniques which govern its field application: 1. Horizontal exploration, or method of the resistivity map, in which a series of electrical measurements are carried out at various stations, keeping the same electrode spacing. Thus, a horizontal layer of the subsoil, of a practically constant thickness, is explored. 2. Vertical exploration, or "vertical sounding"2 method, in which a seriesr of measurements is made with increasing electrode spacings at one or several stations. In this way, the apparent resistivity is determined at a given station for various increasing thicknesses of the ground.

Jan 1, 1934

By R. G. Webber, F. C. Langenberg

During the course of some magnetic investigations which the authors have under way, six bars of 0.43-carbon steel were tested, a permeameter designed after the Hopkinson yoke type being used. The results obtained were of some interest and although far from complete serve at least to show the necessity for a careful investigation of the previous history of the samples under study as well as the chemical composition. A steel of given chemical composition may assume a great variety of structures, depending on its treatment. Professor Sauveur has devised a very clear and effective means of illustrating this point. The accompanying microphotographs show some of the possible structures assumed by a 0.30 carbon steel (Fig. 1). It is now a well-established fact that a structural change is accompanied by changes in the tensile strength, elastic limit, hardness, etc., and it seems reasonable to assume also, a change in the magnetic properties. Six bars of a 0.43-carbon steel were used, all the bars being taken from the same rod and treated as follows: Bar 1. Heated to 1,100° and cooled in the furnace. Bar 2. Heated to 1,000° and cooled in the furnace. Bar 3. Heated to 900° and cooled in the furnace. Bar 4. Heated to 1,000° and cooled in air. Bar 5. Heated to 900° and cooled in air. Bar 6. Untreated. The bars were then turned to 13 mm. diameter and tested by the Hopkinson yoke method. After testing, three specimens were taken from each bar, one from each end and one from the middle. The homogeneity of the bars was tested in this manner and in no instance could any difference in structure in the three specimens1 be detected. Bars 1 to 3 inclusive are pearlitic in structure. The white areas are ferrite (iron with certain impurities in solution) and the dark areas pearl-

Jan 1, 1915

By Strathmore R. B. Cooke

That calcium will activate quartz for flotation with anionic collectors such as soaps has been known for a number of years,1 2 3 and the method has been applied to the concentration of various iron ore 4 5 6 as well as to other materials. Clemmer gives the permissible pH range for the activation of quartz by calcium as between 9.5 and 12.5 with an optimum value of 11.0, and Hertzog7 has determined the calcium abstraction of iron ores and of Ottawa sand, but otherwise little quantitative data are available. The purpose of the present investigation was to determine those conditions under which dilute solutions of calcium chloride will activate quartz for anionic flotation and to determine the amount of calcium ion adsorbed by quartz. Those variables, the influence of which was primary, such as calcium, sodium, and hydrogen ion concentrations, were studied. Other factors which influenced the results are discussed in the description of the experiments. Three different experimental methods were used to determine the activation of the quartz. The first method was to treat a sample of ground, deslimed quartz with solutions of calcium chloride and sodium hydroxide, and to determine the calcium adsorbed by chemical analysis of the solution. Ad- vantages are that a direct value for the

Jan 1, 1949

By S. A. Falconer

D. A. Dahlstrom—Mr. Falconer has done an admirable job of proving the adaptability of the cyclone to the beneficiation of a very difficult size range in the preparation of coal. The addition of the cyclone to other coarser size methods makes it economically feasible for the coal operator to rigorously control his marketed products at a high and uniform quality level down to the 48 and 100-mesh size. Furthermore, it should be pointed out that by utilizing the cyclone as a deslimer or classifier the —3 200-mesh fraction, usually containing large percentages of undesirable material, can also be quickly and cheaply removed from the clean coal. Advantages of such a step are several: (1) Reduction of ash content, especially where clays and slimes are serious. (2) lower moisture content of the final coal. (3) easier mechanical and thermal de-watering of the fine coal due to higher cake and bed permeabilities. The author has indicated that adjustable control means should be installed on the cyclone operating on a heavy-media slurry. This also holds true for the cyclone acting as classifier, deslimer or preliminary dewatering agent and is worthy of special emphasis. Such controls, while not necessarily automatic, must be simple, rapidly adjustable, and require a minimum of attention. Three methods available to the operator are (1) throttling valve on the feed line, (2) back pressure valve on the overflow, and (3) adjustable diameter underflow nozzles. The first two, while fulfilling the specifications, suffer the disadvantage of restricting capacity if severe throttling is necessary. The third method has little effect on capacity and easily maintains an underflow of correct moisture content. Several designs are possible, but two find the widest application. The first was developed by Robert Piros of The Truax-Traer Coal Co. and uses a simple casting containing two holders for underflow nozzles which can be rotated about an axis parallel to the cyclone centerline. These holders retain the underflow nozzle flush with the conical section walls. When a change in nozzle diameter is required, the new size is placed in the spare holder and rotated into place. A second design utilizes a soft rubber cylindrical tube which is compressed or released from three sides, causing the inner diameter of the tube to decrease or increase. This is achieved by using a machine-threaded,

Jan 1, 1951

By S. A. Falconer

D. A. Dahlstrom—Mr. Falconer has done an admirable job of proving the adaptability of the cyclone to the beneficiation of a very difficult size range in the preparation of coal. The addition of the cyclone to other coarser size methods makes it economically feasible for the coal operator to rigorously control his marketed products at a high and uniform quality level down to the 48 and 100-mesh size. Furthermore, it should be pointed out that by utilizing the cyclone as a deslimer or classifier the —3 200-mesh fraction, usually containing large percentages of undesirable material, can also be quickly and cheaply removed from the clean coal. Advantages of such a step are several: (1) Reduction of ash content, especially where clays and slimes are serious. (2) lower moisture content of the final coal. (3) easier mechanical and thermal de-watering of the fine coal due to higher cake and bed permeabilities. The author has indicated that adjustable control means should be installed on the cyclone operating on a heavy-media slurry. This also holds true for the cyclone acting as classifier, deslimer or preliminary dewatering agent and is worthy of special emphasis. Such controls, while not necessarily automatic, must be simple, rapidly adjustable, and require a minimum of attention. Three methods available to the operator are (1) throttling valve on the feed line, (2) back pressure valve on the overflow, and (3) adjustable diameter underflow nozzles. The first two, while fulfilling the specifications, suffer the disadvantage of restricting capacity if severe throttling is necessary. The third method has little effect on capacity and easily maintains an underflow of correct moisture content. Several designs are possible, but two find the widest application. The first was developed by Robert Piros of The Truax-Traer Coal Co. and uses a simple casting containing two holders for underflow nozzles which can be rotated about an axis parallel to the cyclone centerline. These holders retain the underflow nozzle flush with the conical section walls. When a change in nozzle diameter is required, the new size is placed in the spare holder and rotated into place. A second design utilizes a soft rubber cylindrical tube which is compressed or released from three sides, causing the inner diameter of the tube to decrease or increase. This is achieved by using a machine-threaded,

Jan 1, 1951

By B. Haimson, C. Fairhurst

One of the main functions of rock mechanics research has been to find ways of determining in-situ stresses. Many methods have been suggested, the most significant ones calling for measurements inside bore- holes. These methods usually employ some instrumentation for the purpose of measuring hole deformation. Several years ago, a new method was suggested by Scheidegger,l based on previous work by Hubbert and Willis.2 It was the method of "hydraulic fracturing," which had been introduced by the oil industry in 1948 for the purpose of oil-well production stimulation. Basically, hydraulic fracturing consists of sealing off a section of a borehole, pumping in a fluid, and pressurizing it until fracture occurs. If pumping is continued vigorously, the fracture is opened up and extended. In an oil field, such an artificial fracture increases the overall permeability of the formation and usually enhances production. During the entire operation, the variation of pressure with time is ordinarily recorded. Hubbert,2 Scheidegger,1 Kehle,3 and others have shown that the recorded pressures can be theoretically related to the magnitudes of the principal in-situ stresses; the orientation of the fracture can often be used to determine the direction of the principal stresses. The advantage of hydraulic fracturing over the present in-situ stress determination methods is simplicity: no sophisticated instrumentation is required inside the borehole; hence, the stresses can be measured at any depth. Moreover, if the formation is impermeable to the fracturing fluid, no elastic constants of the rock are required in calculating the stresses, a

Jan 1, 1970

By J. M. Locke

Bruckner&apos;s revolving cylinders for roasting ores, etc., are now used at a number of the mills in Colorado and New Mexico, for the purpose of roasting and chloridizing silver ores, with highly satisfactory results, even from those cylinders of small size, erected before the many improvements of recent date. AS examples of the larger improved cylinders, reference can be made to those erected at the Tennessee Reduction Works, Silver City, Grant County, New Mexico, and those which were built, in 1871, at the celebrated Caribou Silver Mill and Mines, Colorado, a mining enterprise which has proved so satisfactory as to have been lately sold to a Holland company for an enormous amount. These cylinders, as now constructed by Messrs. Lane & Bodley, of Cincinnati,,Ohio, are shown in Plate 111, in which Fig. I is an elevation in perspective, Fig. 2 a longitudinal, and Fig. 3 a transverse section. Fig. 4 is a sketch of a mill, with Bruckner&apos;s cylinder. The exterior of the cylinder is a shell of boiler iron, 12 feet long by 5 feet 6 inches in diameter. The ends are partially closed with similar material, leaving in the centre a circular opening about 2 feet in diameter, bounded by a flange projecting several inches. Upon one side is placed an opening closed by a hinged door. Upon the outside of the cylinder are bolted three bands, as shown in Fig. 1, in which the section of the first is square, and that of the third semi- . circular; the second, or middle band, is a strong spur gear. Passing through the cylinder are six pipes parallel to one another, in a plane at an angle of 15" to the axis of the cylinder; these pipes also lie in this plane at an angle of from 30" to 35&apos; to the longitudinal .axis of the plane, as shown in Fig. 2, where the internal arrangement of the cylinder is seen, a perforated diaphragm being formed through part of the cylinder by means of perforated plates placed between

By Gordon S. Duncan

(New York Meeting, February, 1912 THE U. S. Geological Survey, I believe, has almost completed a study of the Harney Peak quadrangle, preliminary to the publication of a report on that, district. As I was engaged for some months on an investigation of the mode of occurrence of the ore-bearing formation in this area, it has seemed to me timely to make public the results of my study, as a contribution to the consideration of this subject. It seems scarcely necessary to describe the locality and general geology of the Black hills of South Dakota, for since 1846 many have contributed information concerning this region, some of the reports bearing such well-known names as those of Walter P. Jenney, Henry Newton, S. F. Emmons, and C. R. Van Hise, while we have only to glance at Bulletin No. 4 of the South Dakota School of Mines, in which Prof. C. C. O&apos;Harra, of that institution, has given us a bibliography of contributions to the geography and geology of the section, to find that other well-known men have studied the district, and have given us the benefit of their researches. The U. S. Geological Survey has made geological maps of nearly the whole of the Black hills, the only quadrangle yet to be completed being, as stated, the Harney Peak district. During the late summer and autnmn of 1910, it was my lot to examine and report. on a considerable area in this neighborhood, which once had been prospected, and in some cases exploited, for tin. This paper gives an account of certain geological phenomena, noted at that time, which greatly influenced my conclnsions. The predominating formation of the district is pre-Cambrian, represented by a highly-cleaved mica-schist, usually very garnetiferous, and sometimes hornblendic. Rising like an island from the surrounding schist is a large mass of granite, known as

Jul 1, 1912

By S. J. Sindeband

Prior to discussing the metallurgy of sintered chromium borides, it is pertinent to outline some of the reasoning behind this investigation and the purposes underlying the work. This study was initiated as an aproach to the ubiquitous problem of a material for service at high temperatures under oxidizing atmospheres, and it was undertaken with a view to raising the 1500°F (816°C) ceiling to 2000°F (1093°C) or better. For the reason that no small, but rather a major, lifting of the high temperature working limit was being attempted, it was felt appropriate that a completely new approach be taken to this problem. A summary of the thinking behind this approach was published recently by Schwarzkopf.&apos; In briefest terms, it was postulated that the following requirements could be set up for a material which would have high strength at high temperatures. 1. The individual crystals of the material must exhibit high strength interatomic bonds. This automatically leads to consideration of highly refractory materials, since their high energy requirements for melting are related to the strength of their atom-to-atom bonds. 2. On the polycrystalline basis, high boundary strength, superimposed on the above consideration, would also be a necessity. Since this implies control of boundary conditions, the powder metallurgy approach would hold considerable promise. Such materials actually had been fabricated for a number of years, and the cemented carbide is the best example of these. Here a highly refractory crystal was carefully bonded and resulted in a material of extremely high strength. That this strength was maintained at high temperature is exhibited by the ability of the cemented carbide tool to hold an edge for extended periods of heavy service. Nowick and Machlin2,3 have analytically approached the problem of creep and stress-rupture properties at high temperature and developed procedures whereby these properties can be approximately predicted from the room temperature physical constants of a material. The most important single constant in the provision of high temperature strength and creep resistance is shown to be the Modulus of Rigidity. On this basis, they proposed that a fertile field for investigation would be that of materials similar to cemented carbides, which have Moduli of Rigidity that are among the highest recorded. The cemented carbide, however, does not have good corrosion resistance in oxidizing atmospheres and without protection could not be used in gas turbines and similar pieces of equipment. It would be necessary then to attempt the fabrication of an allied material based upon a hard crystal which had good corrosion resistance as well. It was upon these premises that the subject study was undertaken and at an early stage it was sponsored by the U.S. Navy, Office of Naval Research. Since then, it has been carried on under contract with this agency. Chromium boride provided a logical starting point for such research, since it was relatively hard, exhibited good corrosion resistance, and, in addition, was commercially available, since it had found application in hard-surfacing alloys with iron and nickel. That chromium boride did not provide a material that met the ultimate aim of the study results from factors which are subsequently discussed. This, however, does not detract from the basis on which the study was conceived, nor from the value of reporting the results which follow. Chromium Boride While work on chromium boride proper dates back to Moissan,4 there has been a dearth of literature on borides since 1906. Subsequent to Moissan, principal investigators of chromium boride were Tucker and Moody,5 Wede-kind and Fetzer,6 du Jassoneix,7,8,9 and Andrieux." These investigators were generally limited to studies of methods of producing chromium boride and detennining its properties. Some study, however, was devoted to the chromium-boron system by du Jassoneix,7 who did this chemically and metal-lographically. This system is not amenable to normal methods of analysis by virtue of the refractory nature of the alloys involved, and the difficulties of measurement and control of temperature conditions in their range. Dilatometric apparatus is nonexistent for operation at these temperatures. Du Jassoneix made use of apparent chemical differences between two phases observed under the microscope and reported the existence of two definite compounds, namely: Cr3B2 and CrB. These two compounds, he reported, had quite similar chemical characteristics, but were sufficiently different to enable him to separate them. The easiest method for producing chromium boride is apparently the thermite process, first applied by Wede-

Jan 1, 1950