Search Documents

By Oda Y, Hashiuchi M

In the smelting section, flexible fuels such as coal or coke are used in place of heavy fuel oil in order to utilize energy sources more efficiently. Heat recovered from the off gas of the furnace has been converted by the waste heat boiler into steam, which is used for self power generation and for heating or maintaining various temperatures. The amount of the recovered steam in the smelter is currently increasing due to maximum utilization of powdered cokes. The heat source required to maintain the temperature of the electrolyte in the tank house is electric power and steam. However until recent year this steam was provided by its own heavy oil combustion type boiler in the tank house since the amount of steam consumed in heating the electrolyte is large. Though experimental work over the last few years has shown the advantages of reducing steam in the tank house by fully covering the cell, the implementation of the full cover can lead to other operating problems. However various improvements, mainly the covering of the cell with a simple device, have led to greatly reduced steam consumption. As a result, steam for the tank house is now provided by the waste heat boiler only bringing more efficient energy usage.

Jan 1, 1987

As partition curves are widely employed to characterize screening efficiency which, by definition, should include a time parameter, it is shown, perhaps for the first time, that time is already included in the partition curves and how. Laboratory and plant results are used to show how screening efficiency depends on feed composition, near-mesh and oversize material and screen motion, and how these factors may combine to give an erroneous result that two identically efficient screens are different and two screens of different efficiency are identical. Reasons are given which show why a renewed interest in screening would benefit not only screen engineers and operators but also those concerned in formulating standard specifications of screen analysis methods.

Jan 1, 1984

By S Steffen, S Talu, J Poulsen, G Watt, A van As, J S. Ooi

The economic success of cave mining projects is significantly influenced by the secondary fragmentation size distribution of the caved orebody and making the fragmented ore available for extraction. If the cave does not propagate as predicted, it may lead to stalled cave growth and/or localised preferential caving. This can cause significant ore loss and the inclusion of excessive waste in draw columns, both of which damage the economic value of the project. Uncontrolled caving can have severe consequences for the safety and economics of mines. Such safety risks include air blasts due to the formation of excessive air gaps and damage to infrastructure due to surface subsidence. Monitoring the cave-back delivers critical feedback that is required to exert control over its propagation and reduce the likelihood of adverse consequences. Current methods for monitoring cave propagation include access through open holes, microseismic monitoring systems, time domain reflectometers and extensometers. All of these monitoring systems rely on stable holes for installation and ongoing data collection. However, cables in holes often get sheared due to ground movement in the seismogenic zone well ahead of the cave front, rendering the systems useless. To resolve this issue, Elexon Mining, with the support of Rio Tinto, developed the Networked Smart Marker system, which is based on Elexon’s Smart Marker technology. This system provides a more robust and versatile alternative to other cave monitoring systems as the data is transmitted wirelessly through rock, and thus is not vulnerable to hole shearing/dislocation experienced with current cave monitoring systems. Installations at the Argyle block cave have proven that the Networked Smart Maker system can continue to provide information on the cave-back’s location long after all conventional monitoring systems have failed. This paper summarises the findings from these installations and highlights the benefits for all geotechnical monitoring systems reliant on the stability of drill holes to remain functional.CITATION:Steffen, S, Poulsen, J, Van As, A, Talu, S, Watt, G and Ooi, J S, 2016. Wireless system for monitoring cave-back propagation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 251–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Bahsford A

The presence of coal in the Sydney area was confirmed in 1891 when Cremorne Bore No. I intersected cindered coal at 1 854 m. The decision to develop Sydney Harbour Colliery was based on the results of Cremorne Bore No. 2 (drilled in 1892) in which a 3.12 m. seam of unaltered coal was encountered at 889 m. Geologists from the New South Wales Department of Mineral Resources consider that this seam is probably equivalent to an upper split of the Bulli seam. Long Cove at Balmain was selected by Sydney Harbour Collieries Ltd. as the site for mine development in 1896. This was due to opposition to the proposed establishment of a colliery on the north shore of Port Jackson near Cremorne. Construction of the main access and ventilation shafts (termed Birth- day and Jubilee), other mine infrastructure and the quay wall occurred between 1897 and 1902. A fatal accident in which five men were killed occurred during the construction of the Birthday Shaft in 1900. This acci- dent resulted in amendments to the Mining Act providing for guide rails in shafts.

Jan 1, 1988

By R Gilbertson, N Freeman

Metallurgical accounting is key to the control and production planning process of any mining operation. This is even more crucial for complex operations involving mining, concentration, smelting, refining and marketing. The tracking of multiple metal product and contaminant components through the operation can improve process predictability and inventory management. Appropriate use can be made of æhigh quality dataÆ for strategic reserve utilisation, mining operations, milling operations, etc. This information enables the optimisation of all aspects of the mining and processing operations. This case study discusses a metal balance implementation for WMCÆs Olympic Dam operations; a large integrated mining, concentration and refining operation, which used an existing off the shelf statistical data reconciliation package developed for the oil industry. It was extended to track and balance the metal co-products across the entire integrated mining, mineral processing and refining plant. The key benefits discussed are tight integration with existing data collection systems, formalisation of previously informal processes, and leveraging the development and support available for a widely used package. The project provided a solution for the site metallurgical balance spanning the mine and processing plant. The solution facilitates a bridge between the planning and production worlds, using a common data model across the site.

Jan 1, 2002

By T J. Napier-Munn

This paper proceeds from the premise that process improvement is a key part of the mineral engineer’s role, and one in which he/she can make a significant contribution to shareholder value. It presents four tools to help with process improvement projects. Two are designed for process monitoring, to determine as soon as possible whether there has been a true change in performance: the cumulative sum (cusum) control chart plot with V-mask, and the control chart using a process model. The other two are used for process optimisation: simplex self-directing evolutionary operation (SSDEVOP), and a response surface model developed using a central composite rotatable experimental design (CCRD). These methods are robust, have a rigorous theoretical basis and are easy to implement. They also promote project continuity which increases the chances of success, particularly in fly-in/fly-out (FIFO) operations. Variants are used in other industries, but they are rarely if ever applied in mineral processing to-day for reasons which are unclear. The paper gives examples of the application of each method in concentrators which demonstrate that they have the potential to be useful additions to the mineral engineer’s professional toolbox.CITATION:Napier-Munn, T J, 2014. Cunning solutions to process improvement, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 5–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Misra A

After review of the status of research on optirnisation of retreat longwall faces it is argued that an acceptable optimisation model must be based upon realistic cost data that take into account not only the face costs, but the total panel costs. These include the cost of development, face cost, removal and installation cost. The determined optimum length of a retreat longwall face is based upon a realistic model and actual costs.Parameters that influence the optimum face length have been varied over wide limits to allow determination of the sensitivity of the model and the effect of the parameters on the optimum face length. It is concluded that for medium production rates and medium system availability, the optimum face length of a retreat longwall face under Australian conditions lies between 180 and 220 metres.

Jan 1, 1995

By Jones JJ

A laboratory study of size segregation is described using a model of a Paul Wurth hopper industrailly employed for blast furnace charg- ing purposes. Experimental charge materials used in the study were glass ballotin.i (1-4mm dia.) and sinter fines (0.25-4mm). The tracer material employed consisted of coloured glass beads. The results of the study show that the discharge stream from a Paul Wurth hopper is characterised by an initial negative segregation followed by a positive segregation and that this segregation pattern is a property of the hopper geometry and the filling conditions. A simple computer model based on experimental tracer concentration results is proposed. The measured segregation results and those predicted by the model show close agreement. Application of the results with special reference to the effect of size segregation on charge permeability in blast furnaces is also included.

Jan 1, 1984

Autogenous and Semi-Autogenous grinding has become an accepted method of reducing primary crusher product to micron sizes in a single or a two-stage grinding circuit. The elimination of secondary and tertiary crusher circuits and sometimes rod mills helps to lower overall operating costs and, in many instances, can make uneconomical projects viable. Selecting AG/SAG Mills have been rather a "hit and miss" affair over the years, but now with the many different types of tests available, accurate mill size predictions can be made, provided the test data is evaluated correctly. This paper endeavours to simplify the process of evaluating test data and sets down some guidelines for designers to follow when selecting AG/SAG Mills.

Jan 1, 1991

By S Lee, I Sohn

The ferrous and non-ferrous metallurgical industries have been utilising slags, fluxes and mattes for process optimisation and quality improvements at high temperatures. Understanding the fundamentals of the thermodynamics and kinetics of chemical metallurgy regarding slags, fluxes and mattes has been essential to the technological developments of these optimisation and improvements. This work will discuss how these fundamentals have been studied in the reactions involved and implemented in the ferrous industry from primary refining to continuous casting. In particular, the chemical driving forces that allow these reactions to take place and the limitations of the kinetics that require optimisation to enhance the reactions. In addition, the future research direction for slag technology innovation and the role of these fundamentals will also be described.

Jun 19, 2024

By Taylor GP

Mt Kasi in Fiji is a high sulphidation style of gold deposit exposed at a high crustal level. Individual alteration centres are localised at the intersection of cross structures within a through-going structural corridor, the Mt Kasi Fault System. A two stage alteration/ mineralisation model suggests that much of the high sulphidation alteration is derived from the initial rapidly moving gas-rich portion of the hydrothermal fluid. The gradual cooling and neut-ralisation of hot acid fluids by mixing with oxygenated ground waters forms the characteristic zoned alteration assem-blages which grade from cores of residual silica through silica-alunite to peripheral clays. The liquid-dominated phase of the hydrothermal fluid brecciates the competent, altered rocks and deposits sulphide mineralise-ation within the breccia matrix. High gold grades occur in the matrix-rich breccias and decline from the hydro-thermal fluid upflow to outflow zones.CSAMT (controlled-source audio magneto-tellurics) geophysics has been used to define the geometry of the alteration centres while strike slip movement on the major structures accounts for the dilational structural environment in which the ore hosting breccias form.

Jan 1, 1994

By Nakajima A

Some attempts were made to recover uranium from aqueous systems by using various biosubstances including microbial biomass. Of hundreds species of microorganisms tested, extremely high uranium absorbing ability was found in Pseudomonas stutzeri, Neurospora sitophila, Streptomyces albus and Streptomyces viridochromogenes. In parallel to this research, various kinds of biomass and commercially available crude drugs were screened to measure their abilities to adsorb uranium. Of these biosubstances tested, high uranium adsorbing ability was observed in chestnut skin, Comi fructus, Geranii herba and Chaenomelis fructus. From these results it may be considered that the uranium adsorbing ability of these biosubstances is due to the following; the uranyl ion is co-ordinated by the polyphenolic compounds such as tannin existing in the biosubstances. Along with these fundamental researches, we have developed a new adsorbent, the immobilised persimmon tannin (kakishibu tannin), for uranium and thorium. This adsorbent can accumulate 1.71 g of uranium per gram of the adsorbent (14 mEq/g), and the uranium adsorbing capacity of this adsorbent exceeds by several times that of commercially available chelating resins (2 - 3 mEq/g). We attempted to recover uranium from uranium refining waste water by using the immobilised persimmon tannin. As a result, the immobilised persimmon tannin can recover trace amounts of uranium from uranium refining waste water containing 10 - 15 ppb uranium with high efficiency. Almost all of the uranium adsorbed onto the adsorbent can be desorbed by washing with 0.05 - 0.1 M HCl or H2SO4. Thus, the immobilised persimmon tannin can be used repeatedly in the adsorption-desorption Cycle.

Jan 1, 1993

By A R. Sale

This paper highlights two aspects of the mineral sands industry in Australia: the development of the industry from approximately 1870 through to 1980, and the author’s experience in the industry from 1966 to date.The first real heavy mineral (HM) mining in Australia started in 1870 with the mining of heavy mineral slicks on the beaches along the east coast of Australia. The real potential of Australian heavy minerals was however only realised in the 1920s with the first production of a heavy mineral concentrate that was shipped to Canada for processing. Post WW 11 and the Korean War, Australia was the largest producer of mineral sands products in the world as well as a significant developer of associated separation equipment and technology. The number of producing companies in the east coast peaked at 33 in 1957, was reduced to ten by 1965, and subsequently further reduced to five in 1980 as a result of potential mining areas being declared National Parks or Conservation Reserves. Today there is one company, Unimin Australia Pty Ltd (formally Consolidated Rutile Ltd) operating on the east coast. In contrast there were three companies on the west coast in 1965, four companies in 1980, and four companies today (albeit not the same companies).There have been considerable ups and downs for the industry in Australia, however world wide it was renowned in the past as being an industry that attracted numerous interesting and innovative characters that played a major role in developing it into the vibrant industry that it is today. This, given the current climate, is predicted to continue into the future.The author has been continuously involved in the industry for over 45 years from 1966, initially as an electrician at Consolidated Rutile Ltd culminating in the role of General Manager/President of Iluka Resources Limited USA, prior to his retirement in 2009. His exposure has been world wide and has covered all aspects of the industry but in the main focused on project development and operational areas. During this time there have been significant technological advances, yet to some extent the basic principles have not changed at all. Some of the most noteworthy advances include the development of the Wright Spiral in 1977, the development of the Reading High Intensity Wet Magnet (WHIMS), the rare earth magnets, the CRL floating thickener and the improvement of analytical techniques. From a safety, health and environmental perspective there has been significant advances that the industry has much to be proud of. These include wetland restoration both in Australia and in the US, the restoration of farmland in Virginia and Capel, and the re-establishment of native species, for example at Eneabba and Richards Bay to name but a few.

Oct 5, 2011

By P Salmon, M Kennedy

Sun Metals Corporation Pty Ltd (SMC), a wholly owned subsidiary of Korea Zinc Co Ltd (KZC) is a company formed to develop, construct and operate a zinc refinery, 11 km south of Townsville in North Queensland. The project opportunity exists because of on-going consumption growth for refined zinc metal, technological, environmental and economic obsolescence of existing zinc processing plants, and a prolonged ædroughtÆ of new zinc processing capacity under construction. The Project will utilise proven technology developed by KZC at the Onsan refinery in Korea. The Townsville Refinery has been designed to be the most environmentally-friendly zinc refinery in the world, and in particular to resolve the issue of secure, long term treatment of the ironbearing content of the zinc raw materials.

Jan 1, 1998

By M Edgar, G Pattemore, M Auad, K Job, A Job, S Gale

In recent decades, significant advances have improved the modelling techniques for predicting slope failure. Predicting failures is vital in open pit mining due to the significant risk posed to personnel and equipment from unstable pit walls. Failures not only cause harm and damage to people and equipment but also cause delays to production and subsequently increase operational costs. Coupled with improvements in modelling techniques, utilisation of advanced scanning systems, such as high-definition imagery from UAVs has enabled faster and more precise mapping and modelling. However, one key element required for accurate slope stability modelling and monitoring is the ability for mine geotechnical engineers to have an accurate understanding of the mineralogy and moisture content of slopes, in real-time. To address this challenge, research has been undertaken to utilise hyperspectral imaging across a broad spectrum, combined with high-definition imagery, and LiDAR to scan slopes for minerals and moisture content. In addition to accurately mapping mineralogy and moisture, the data must be collected autonomously and remotely to ensure ongoing safety. The results show that there are many direct and indirect benefits from this new technology, including the ability to monitor slopes at a safe distance and in real-time, improved accuracy of modelling, detection of risks, and improving the automation workflow for geotechnical engineers. The paper presents recommendations for the implementation of the technology in open cut mining environments.

Jun 22, 2022

A combination of the needs of business, employee desires and safety and health considerations is stimulating increasing attention to the time spent by people at work and the timing of that work. Particularly we are seeing: - innovative work schedules for 24-hour mining businesses; and - response from industry to accommodate the needs, even the desires, of employees in return for systems which are more productive and more capital efficient. There appears to be an evolutionary trend for business management to become more sophisticated and responsive to the need for achieving close to best cost work schedules to sustain continuous improvement. The underlying motivating forces driving this trend for improved techniques in organising attendance at, and time spent at work, is the seemingly inseparable combination of technological advance and ever-increasing accumulation of capital. The mining industry has not remained untouched by this thrust for ever-increasing need for best use of labour, to adopt advances in technology and to provide attractive opportunities for putting accumulated capital to work. An essential component of this on-going thrust is a substantial effort by the mining industry to improve the performance of labour by providing most-productive work schedules.

Jan 1, 1996

Polish coal mines are well equipped with methane monitoring systems,nevertheless the worsening conditions force a continuous impro- vement in the field of environmental monitoring. Application of modern electronic components make it possible to design the new modular telemonitoring system incorporating the best features of the older systems,widely employed in Polish collieries, eliminating their weak points. Several new sensors and portable instru- ments for methane monitoring and early fire detection have been developed and tested in mining conditions.

Jan 1, 1988

By Linge HG, Klauber C

The key element in the carbon-in-pulp process for gold processing is the loading of dissolved Au(CN)2 from solution onto activated carbon. The mechanism and kinetics of this step have been examined by solution adsorption-desorption and X-ray photoelectron spectroscopy for both coconut derived activated carbon and peat-based activated carbon. The results show that these carbon types have the same mechanism and kinetics of adsorption. There is no contribution to the bonding from carbon-oxygen functionalities on the carbon surface, as has been invariably supposed in all previous theories for the mechanism of the reaction. It is shown that Au(CN)Z is reversibly adsorbed intact on and parallel to the graphitic planes of the carbon with the formation of a weak carbon-gold n-donor bond. The kinetic measurement of carbon gold loading reactivity is discussed and use of the Murdoch equation for this test is critically assessed.

Jan 1, 1989

By Stanton G

The Department of Mapping and Surveying (DMS), the Australian Key Centre in Land Information Studies (AKCLIS), the Department of Industry Development (DID) and the State Government Computer Centre (SGCC) are testing a regional information network in northern Queensland. Several study sites have been chosen by different groups of participants. The members of each common-interest group share their data for the site. They can also access datasets supplied by other organisations that are not directly involved in the particular study being undertaken. The participants include state government departments, local authorities, fed- eral organisations and the private sector. The participants communicate with computer systems in Brisbane via Q-Net. Q-Net is a pilot State government tele- communications network, established by the Department of Industry Development. Q-Net uses the communications sat- ellite AUSSAT 1 as the primary instrument of data transfer. The Q-Net network is a star system, with a Master Earth Station in Brisbane acting as a hub for radial earth stations, located throughout Queensland.

Jan 1, 1987

By S G. Gemell

"The financial model is an integral component of any project evaluation based on mineral resources, ore reserves and (at least internally) exploration targets. Given the unity of purpose for preparing financial models for project evaluation purposes, the diversity of both format and content of the finalised models is surprising. Many models are prepared by staff or consultants who are comfortable with a particular format that may be used for other purposes, such as budget preparation or financial reporting. It is natural in these situations that the practitioner will take these models and adapt them to the purpose. The end result may or may not succeed in providing a clear, accurate and sufficiently detailed view of the project’s economic viability.When preparing a model, the practitioner should be cognisant of the interpretation and review, or audit, process. The auditor may be a consultant or employee of a bank, potential equity provider or of the project sponsor itself. Depending upon the scale of the project and the level of participation of the entity that the auditor represents, the financial model will be interrogated more or less rigorously. In any event, the end user will require the model to permit easy change of inputs and will wish to confirm that such change is appropriately and thoroughly transmitted throughout.Accordingly, there are some ‘dos and don’ts’ that can be readily applied in the creation of the financial model that will greatly assist the end user, not just in the change of inputs, but also in reviewing the model’s integrity. The less time and effort required by an auditor in this regard is reflected directly in the cost of the review process.CITATION:Gemell, S G, 2016. Financial modelling with the auditor in mind, in Proceedings Project Evaluation 2016, pp 172–180 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016