Search Documents

By Horiszt G

his report is going to point to that the effect of the mining dewatering on the area of Transdanubian Mountain Range has reached a phase when the cost of dewatering and providing damages can seriously jeopardize a profitable mining operation. Up to 60s the interest of mining had been dominant only, but since the begining of 80s the conceptions of industrial development and the value of enviroment protection have been changed. The natural karstwater balance of the TMR can be presented (Figure Land 2.) and the present situation of it points to that the descharge has exceeded the reacharge in 50 %. During the past 10 years the decreasing of the stored karstic water resourches was 1.1 km . The decreasing of the spring yields reached 80-82 % of the natural ones. (Figure 3-4.). Conservation of the present discharge may lead up to the totaly drain of the karstwater regime. A computer aid control system had been to develop by the bauxite mining and using of it the yield of dewatering decreased and a moderate rising of the water table has started since 1986. A recunstruction was made at the biggest thermal-medicinal lake its springs have had their source in 40 meter depth inside a spring cave at the bottom of the lake. Earlier the spring yield decreased due to the dewatering activity of mines. As a result of using of the CAC system and the providing works at the thermal sprino,the karstwater balance has got in the state of equilibrum, the first cost was decreased and spring yield was increased and the enviromental limits were adverted from the way of mining.

Jan 1, 1988

By Davies B, Rogers A, Grainger A, Todd J, Brenman R, Jones L, Horton B, Eager L

Research into the control of diesel particulates (DP) has been. conducted by BHP Coal for more than 7 years. Personal monitoring of employee exposures (n = 480 full shift samples) conducted at nine underground coal mines has indicated that the exposure of the workforce ranges from less than 0.1 to 2.2 mg/m3 of DP dependent on job type and mining operation. Approximately 50% of the mass of DP captured is elemental carbon (EC) which is the species currently being considered by some international regulatory authorities as the exposure standard. Five technologies for controlling DP were investigated in a combination of studies conducted in an above ground simulated tunnel, in a special controlled section of underground mine roadway and validated by application in standard coal mining operations at Tower Colliery. Tests conducted under controlled conditions indicate that dependent on the type of fuel in use, the introduction of low sulphur fuels can reduce DP levels in return airways by up to 50% and in actual mining situations a reduction of 20% can be achieved in exposure of the workforce. In addition, subjective responses from the workforce indicate that exhaust emissions from low sulphur fuels provide lower irritation and a more pleasant aroma. The use of water filled scrubber tanks reduces the level of DP emissions by 25%. Chemical decoking of engines resulted in a reduction of 20% in DP in return airways. A commercially available non-flammable disposable dry exhaust filter constructed from synthetic organic fibres with an operational lifetime in excess of 20 hours was found to reduce DP exhaust emissions by 80%. Investigations have indicated that the use of increased ventilation to control DP levels particularly in multiple vehicle situations does not follow a simple dilution factor and in some instances compliance with current regulatory requirements may not produce the required reduced exposure levels. The results from single component control strategies provide considerable reduction in exposure to DP, however the most efficient and cost effective control methodology is the use of a combination of individual systems modelled to operations conducted at each mine.

Jan 1, 1998

By H Park, D J. Holland, L Wang, Y Matviychuk, Y Lee

Reuse of process water in mineral and coal flotation plants is widespread to effectively reduce freshwater consumption. However, the accumulation of the frother in the recycled process water is a growing problem as high remnant frother concentration often leads to undesirable overfrothing issues throughout the plants. Various approaches have been proposed by others to measure frother concentration, but none of them is used in flotation practice owing to the requirement of timeconsuming sample preparation steps and/or specialist training to operate and maintain. There is a pressing need for the development of a simple and fast frother concentration measuring technique to avoid overfrothing issues and to optimise the flotation process. The present paper presents two promising approaches to measuring frother concentration online. The first approach measures the concentration of alcohol type frothers based on the host-guest interactions between frother molecules and a formulated liquid. This method is simple and fast as it only requires mixing the formulated liquid with the water sample for up to one minute. The potential of this approach was demonstrated by determination of the residual MIBC concentrations at different locations across a coal flotation plant. The second approach measures frother concentration using a solid-phase extraction (SPE) process and a cryogen-free benchtop NMR spectrometer. Using this approach, both alcohol type and polyglycol type frother solutions can be analysed for concentration determination within 30 minutes. It has also been demonstrated that the concentration of individual frothers in a frother blend (ie MIBC and PPG425 in water) can be accurately analysed even in the presence of background chemicals. This technique has otential for real-time measurement of frother concentration as the whole process can be fully automated.

Aug 24, 2022

The value of Australia's education services exports increased to over $15 billion dollars in 2009, placing education as the third overall export earner behind coal and iron ore; however there are concerns over the impact of emerging policies on the future of both the industry and the provision of mining education. Policies have impacts on the growing number of international rankings (or league tables) of mining jurisdictions and universities. A high position in such rankings might be used as a measure of perceived quality with benefit to those at the top and to the detriment to those lower down.    Top performing companies in the relatively new domain of sustainability have been shown to achieve better financial performance than their industry competitors, assisting them in attracting top quality committed staff, hence positioning themselves well for the future. The world's mining companies, jurisdictions and universities are now ranked with results in the public domain. It is argued as to the validity of the data or perceptions used in such rankings, but there is no doubt they are influential in determining the flow of dollars around the globe. By investing your pension fund assets in the shares of the top performing companies, by placing your exploration dollars in a country at the top of such a list of attractive jurisdictions, attending or recruiting from a University at the top of the rankings - risk must surely be reduced?   While savings and risk reduction can undoubtedly result from the introduction of new technologies developed through appropriate R&D (the other core activity of a university), the maintenance of a very high level of exploration and production performance through dedicated highly skilled staff every hour of every day quietly improves financial performance, while avoiding safety, environmental and/or community incidents (ie protects the 'triple bottom line'). As always risk reduction comes down to enabling quality people to do a quality job - through the actions of such people we can sustain the global mining industry and secure our social license to operate. However, there is global concern over where the numbers of such people, including those with the recently required skills in sustainability, are going to come from.   This presentation will discuss some of the complexity and interactions involved in the development of such rankings, the dangers inherent in their simple acceptance and use, plus indicate some of the directions mining educators might take to sustain and increase the supply of quality graduates to the global mining industry. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Jun 1, 2010

By D S. Stewart, K W. Keskimaki

The Henderson Mine has been utilising a continuous panel caving method to extract molybdenum ore since starting operation in 1976. In the past three decades since the mine was designed, many changes have taken place in underground technology as well as the general nature of the mining business. The impacts of larger scale underground equipment and automation are significant at Henderson and continue to reshape the nature of the enterprise. During the first years of operation in the 1970s, Henderson required almost 2000 employees to achieve full production, today only about 400 people are required to fully utilise the plantÆs capacity. The most recent change to the facility is the conversion from a rail haulage system to an underground crushing and conveying system that transports ore 25 km to the Henderson mill site. This change has required the introduction of large, rubber tired haulage trucks underground and the mining methods necessary to develop the large openings demanded by the trucks and underground crusher. The development of the underground crusher is also the first step to mining the final bottom horizon of the orebody. Along with this move comes an opportunity to almost triple the effectiveness of the mining effort, through higher draw columns and wider draw bell spacing. This final advancement to a totally trackless mine has positioned Henderson well for safe and efficient operation as it enters the 21st century.

Jan 1, 2000

By D J. Williams, E M. Rykaart

Soil cover systems are routinely used to reduce acid rock drainage (ARD) from mine waste rock dumps and tailings impoundments. A technology for the analysis, design, instrumentation and monitoring of barrier-type (oxygen limiting) and store/release-type covers has rapidly developed and the number of covers under construction has grown extensively during the past ten years. Mine operators are currently investing in this relatively new technology with the expectation that these covers will reduce long-term liability with respect to acid generation, drainage and treatment costs. While the design life for cover systems may extend into hundreds of years, we have less than ten years of construction experience and proven performance. Some cover designs appear to be functioning well; however, the performance of many more is now being called into question. The paper presented herein evaluates the integrity of cover systems from a global perspective. Soil cover systems for the control of ARD are being constructed at mine sites located within high rainfall equatorial regions, deserts ranging from low to high latitude, humid temperate regions, and cold-continental climates. While the technology for analysis and design of soil cover systems is well developed, factors that compromise the performance of cover systems (in addition to the paramount issue of climate) relate to material selection and availability, cost and construction practices. Long-term performance is also strongly affected by physical stability (ie erosion), volume change (ie cracking, desiccation, settlement and freeze/thaw cycling), vegetation, soil evolution and ecological stability. This paper provides a review of the application of soil cover systems for the control of ARD. Cases where cover systems have been constructed with both success and failure are illustrated. General criteria and recommendations for cover selection, design, construction, and maintenance are provided.

Jan 1, 2003

By C A Heinrich, Jaques A. L, L A I Wyborn

Most orebodies have cross-sections of less than I km2 and hence do not offer a particularly large target for exploration. Fortunately, although in the geological record ore deposits are small and rare and result from the exceptional coincidence of certain geological processes, these processes are mappable on a much larger, district to regional scale and constitute a mineral system in which the ore deposit is the central feature. A mineral system can therefore be defmed as 'all geological factors that control the generation and preservation of mineral deposits, and stress the processes that are involved in mobilising ore components from a source, transporting and accumulating them in more concentrated form and then preserving them throughout the subsequent geological history'. The mineral system concept emphasises that for many ore deposit types, although economically viable mineralisation may only occur on a scale of say, hundreds of metres, the total system offluid-rock interactions that led to ore formation can extend over a distance of tens to hundreds of kilometres around the deposit. When mapped out, the total mineral system provides a far larger exploration target than the actual ore deposit itself. Important geological factors defining the characteristics of any mineralising system include: I. sources ofthe mineralising fluids and transporting ligands; 2. sources ofthe metals and other ore components; 3. migration pathway; 4. thermal gradient; 5. energy source; 6. a mechanical and structural focusing mechanism at the trap site; 7. chemical and/or physical traps for ore precipitation. Many of these factors individually are common through

Jan 1, 1994

Within the Mt Whaleback open cut mine the integrity of the final pit wall is achieved through careful rock slope design, use of rock reinforecement technology where marginal stability exists and use of controlled blasting techniques and excavation practices. By reducing the effective density of ANFO explosive within blastholes to around 0.2 glcm', and developing standard blast pattern designs for various rock types, blast damage to pit walls has been minimised. Accurate geological prediction is necessary for optimum blast design. Controlled blasting is undertaken where blasting occurs within 90 m of the designed final batter crest and hole by hole assessment of final limit blast patterns is undertaken before pattern charging. Shovels and trucks remove the bulk of blasted and dozed rock material, but due to the mine's variable pit wall slope configuration, bulldozer excavation of some critical design batters has been successfully Implemented.

Jan 1, 1986

The GDR has extensive lignite deposits at its disposal, which formed the basis for the development of an independent energy source after 1945 and which will retain their significance well beyond the year 2000 (see fig. 1). In 1946 lignite output was about 110 x 106 t. In 1985 312x 106 t was produced and in 1988 the planned output will be ca. 315 x 106 t. Thus, the domestic produc- tion of lignite covers ca. 75% of the GDR's primary energy requirements. More than 80% of the electrical energy is gener- ated by the use of lignite and about 12% by nuclear energy. In addition to this, about 18 x 106 t/a mineral oil and about 6 x 109, m3/a natural gas are imported, predominantly from the Soviet Union. The lignite deposits of the GDR are of Tertiary origin and are recovered exclusively by opencast mining. There are two large regions (fig. 2): - in the region east of the river Elbe (Cottbus/Senftenberg- "Niederlausitz") and - in the region west of the river Elbe (Halle/Leip- zig/Magdeburg). These deposits differ in geological age and conditions of depo- sition, consequently there are differences in their chemical and physical composition and, thus, in their uses. The younger Mio- cene coals of the main region in the East of the river Elbe belong to the epirogenetic type and have a low content of ash and sul- phur. Among other things, they are suitable for the production of brown coal high-temperature coke (Lauchhammer and Schwarze Pumpe). The older Oligocene coals of the Halle/Leip- zig region are bitumenous in certain areas. Therefore, they form the basis for production in low-temperature carbonizing and chemical plants. In the Halle-Magdeburg region, where the lig- nite is in contact with the underlying Zechstein subdivision, so- called "salt coals" are found.

Jan 1, 1989

Authorisation No.66 (to Prospect) was allocated to R.W. Miller & Co. Pty. Ltd. on 1st November, 1976. Exploration has brought coal reserves to measured status in the Jerry's Plains sub-group which are about 550m. thick. The immediately lower Vane Sub-group, about 200m. thick, includes about 20 seams. The total measured and indicated reserves of the two sub-groups based on the criteria adopted by the company amount to 1362 million tonnes in situ. This very large resource is subject to very many mining constraints both physical and economic which limit the saleable reserves under present conditions to about 120 million tonnes. The results of the calculation of reserves after exploration is complete in a deep multiple seam situation is dependent upon the criteria used to include or exclude seams in the reserves. These criteria are state- ments of the miner's expectations of the market, mining and coal preparation technology, local and national politics and the law as it may be applied in the future.

Jan 1, 1979

By Resta S. A

Energy Resources of Australia Ltd - Ranger Mine is located about 255 kilometres east of Darwin in the Alligator Rivers Region of the Northern Territory. The Ranger project is surrounded by Kakadu National Park which is on the UNESCO World Heritage list. . Ranger Mine operates the largest uranium mine and processing plant in Australia. It is designed to produce 3000 tonnes of uranium oxide per year, but presently is producing a little less than one half that figure due to the depressed uranium market. The safety performance of the employees and Ranger as a whole continues to improve. The lost time injuries (LTI) have significantly reduced from 74 in 1985 to five in 1994. The total days lost due to LTIs have gone from 1543 to 14. These significant improvements have reflected directly on workers' compensation premiums in which a four-fold reduction has occurred. It is estimated that the actual monetary saving to the company is about $1.3 million per year and directly reports to the profit of the company. There is also an obvious and significant reduction in the less quantifiable costs such as the suffering of the injured employees and cost to society. The paper will review the various initiatives introduced and assess their effectiveness. Performance improvement is primarily dependent on the commitment, introduction of various initiatives and the subsequent change in workplace culture.

Jan 1, 1994

Discovered in 1954 and mined since 1966, the X41 copper orebodies have produced over 143 Mt @ 3.3 per cent copper. By June 2002 the production from these orebodies had depleted the Mineral Resource to 36.6 Mt @ 2.8 per cent Cu (including 31.5 Mt @ 2.5 per cent Cu combined 2002 Ore Reserve). Mine production will ramp down to cessation beyond ten years. The 2002 Copper Business Study was commissioned to review the status of the Mount Isa copper business and to optimise the long-term strategy of the operations. The study resulted in a vastly improved geological and geostatistical model, and financial studies led to the optimisation of mine cut-off grades. Utilising these new models, a near-mine target generation workshop was conducted by the copper stream geology team. The workshop focussed on exploration for new ore sources and the extension of existing orebodies to supplement the Mineral Resource inventory for future conversion to Ore Reserves. Several prospective targets were identified and the Conceptual Northern 1100 Drilling program was subsequently designed. This paper shall discuss the practicalities of near-mine target generation in Mount Isa, the issues faced when locating and preparing drill sites in a mature mine environment, and the preliminary results of the drilling program so far.

Jan 1, 2003

By C F. Nichol, L Smith, R D. Beckie

A better understanding of the hydrogeology within mine waste rock and cover systems is essential for the quantification, prediction and prevention of metals loading to the environment surrounding waste rock piles. The effect of surface condition on the internal flow mechanisms within an intermediate-scale constructed waste rock pile is being investigated at the Cluff Lake Mine, Saskatchewan. Changes in the water balance, the outflow distribution and water residence time have been observed in the waste rock pile following successive modifications of the surface condition. The three year old, run of mine, free-dumped surface was ripped to a depth of 30 cm to 40 cm, and levelled in October of 2001. In August 2002, a 10 cm to 15 cm cover of compacted waste rock was placed on the pile. Outflow, precipitation and run-off data collected during natural and artificial rainfall events have been used to quantify the maximum infiltration rate, and the spatial pattern of discharge and cumulative volume of water that infiltrated into the waste rock under each surface condition. Infiltration data together with the outflow data provide a basis to address the residence time of water within waste rock and the dominant flow mechanisms for different surface conditions. With a free dump surface spatially distinct wetting fronts are observed at the base of the pile that vary in flow rate by an order of magnitude (measured at a 2 m by 2 m scale) and in time by up to a week. Following ripping and levelling, similar cumulative outflows were observed, but the magnitude and arrival time of wetting fronts changed across the pile. A decrease in outflow volume, a decrease in infiltration volume, a two-fold increase in the response time of wetting fronts and a more spatially uniform distribution was observed following placement of the compacted surface layer. Based on preliminary data, the internal structure appears to be the dominant factor controlling outflow variability.

Jan 1, 2003

By I Cameron

Simulation is increasingly being used to analyse mineral processing operations and explore efficiency options. Engineers that use simulation are rightly concerned with the quality and applicability of the underlying models. However, many of these models have a significant empirical component, and the best structure for this component may not be apparent. There is an opportunity to improve the quality and application range of these models by exploring potential structures for this empirical element. One approach to this problem is the use of structural optimisation, which is a formalisation of the model development process. This method searches through a family or hyper-structure of candidate models for a model that is optimal with respect to some measure of model quality. This method has been applied to the modelling of an industrial flotation circuit. The result was a model that was a significant improvement over a number of standard models reported in the literature. Structural optimisation provides a method to compare potential models in a systematic and efficient way, and hence to improve the structure of process models.

Jan 1, 1998

By I A. Lamb

The Melbourne City Link Project has two tunnels, the Domain and Burnley Tunnels, which have been constructed by Transfield Obayashi Joint Venture (TOJV) under a design and construct contract. The two tunnels are located essentially under the Kings Domain, the Yarra River and, in the case of the longer Burnley Tunnel, under the inner suburb of Richmond. The Burnley Tunnel is 3.5 km long and reaches a depth of 65 m at the central Swan Street Shaft, the invert being at RL -60 m. The Domain Tunnel is 1.6 km long, with the invert reaching RL -20. The tunnels were driven, for the most part, in the siltstone and sandstone of the Silurian Age Melbourne Formation. Construction aspects of the driven tunnels as related to the engineering geology have been described by Hutchison et al (1998). The Silurian bedrock is a fractured rock aquifer that is connected to overlying alluvial aquifers. Excavation of the tunnels allowed temporary groundwater inflows which substantially de-pressurised portions of the various aquifers. This de-pressurisation provided the potential to accelerate on-going secondary consolidation rates of the Holocene Aged Coode Island Silt (CIS) and the older Quaternary Fishermens Bend Silt (FBS) deposits, in areas where these materials directly overly the aquifers. As a large portion of the urban area of South Melbourne and the old river course of the Yarra River contain extensive CIS deposits, and were within the drawdown influence of the tunnels, the management of the hydrogeological regime was very important. The permanent design of the tunnels comprised drained and undrained sections (a partially tanked design) which, along with some permanent recharge, provide long-term protection against the possibility of accelerated settlement rates. During construction TOJV implemented a comprehensive groundwater management plan to deal with issues related to the temporary drawdown of the aquifers and the temporary acceleration of settlement. This paper describes the hydrogeological regime, the effects of the tunnelling, the monitoring programs, the extensive temporary recharge system, and the consultation program that TOJV utilised to manage the hydrogeological issues.

Jan 1, 1999

By C M. Côte, P Bolz, R Chrystal

The design of final landforms is an integral part of mine closure plans in Queensland and aims to ensure the rehabilitated land is safe, stable and non-polluting. Landform stability in this context is commonly assessed using Landscape Evolutions Models (LEM) which are physical models simulating sediment erosion and deposition around individual landforms over long timespans (up to thousands of years). The most used LEM for assessment of rehabilitated landforms in Queensland is SIBERIA (Willgoose, Bras and Rodriguez-Iturbe, 1991; Tucker and Hancock, 2010). SIBERIA models are complex, require very detailed input data and simulate erosion and deposition over time frames that extend decades beyond closure. They are not suitable to assess erosion risks during the operational phase of a mine and to support the development of erosion and sediment control plans. Other types of erosion models, such as the Revised Universal Soil Loss Equation (RUSLE, Wischmeier and Smith, 1978) or Water Erosion Prediction Project (WEPP, Nearing et al, 1989) calculate soil loss on a monthly or yearly basis and are much better suited to erosion management during the operational phase. They are simpler to implement and can support the design of control measures. For instance, designing a sediment basin requires quantification of sediment loads, which can be produced by these models. In Queensland, the legislation around sediment and erosion control for open cut mines is currently tightening. Soil erosion remains a major concern due to potential impacts on the receiving environment. It requires management during operation and for closure consideration alike and it is critical that erosion and sediment control plans are developed with the most appropriate tools. Globally, RUSLE is the most widely used soil loss model (Borrelli et al, 2021). This is because it is an empirical model with relatively simple input requirements: biophysical data such as soil properties, vegetation cover, topography and rainfall variability, which can be directly measured or derived from regional or national databases and/or spatial data sets that are available in most parts of the world. The second most used model is WEPP (Borrelli et al, 2021) but compared to RUSLE, there is a large drop in the frequency of its use. This is because WEPP is physically-based and has more complex data requirements. WEPP integrates hydrology, hydraulics, erosion mechanics and land cover to predict soil erosion and sediment transport on hill slope profiles and small watersheds (Stolpe, 2005). It requires some biophysical parameters in formats different from those of RUSLE, as well as detailed hydrologic and catchment data. Nevertheless, it has been used in landform design for mines across Australia to determine final landform stability (eg Howard and Roddy, 2012; Costin, 2020). In this study, we assess which tool would be the most appropriate to support development of erosion and sediment control plans from operation to closure. We use RUSLE and WEPP to predict soil loss from a mine site, compare the results from both models and outline the advantages of each method.

Aug 2, 2023

By J Jeffrey, G W. Wilson, L Gilbert, C

Prior to the commencement of mining, the acid rock drainage (ARD) potential of the waste rock to be produced by an open cut mining operation is assessed by a variety of techniques carried out on drill-hole samples. These include, among others, acid base accounting (ABA), net acid generation (NAG) testing, and kinetic testing. Based on the results obtained, a strategy for the identification, separation and selective placement of waste rock having different potentials to form ARD is developed. During the course of mining, the waste rock classification scheme will be re-assessed periodically to confirm that it is appropriate. This re-evaluation may result in a change in classification scheme, and waste rock dump samples may be obtained for ARD assay purposes to confirm the appropriateness of the revised scheme. The paper describes the evolution over time of the scheme used to classify waste rock at a major open pit gold operation in New South Wales, Australia, including the development of a hydrological model. To confirm the appropriateness of the revised scheme, ARD assay testing was carried out on drill-hole samples collected from dumps having different ARD potential designations, including Non-Acid Forming (NAF), Potentially Acid Forming (PAF), and Low Grade Ore stockpiles. The results of the ARD assay testing and water quality monitoring confirmed the appropriateness of the ARD potential designations and the revised classification scheme, which has been adopted.

Jan 1, 2003

By Thatcher R

In areas where undeveloped land represents a scarce resource, an upgraded post mining land use can result in economic benefits to both the mining company and to the community. A study undertaken at Allied Queensland Coalfields Ltd's Aberdare Colliery located between Brisbane and Ipswich during 1986/1987, assessed the costs and benefits of developing the site following mining for grazing, forestry and residential uses. The proposed final land use plan comprised a combination of these uses which can be upgraded to higher valued uses once subsidence monitoring of backfilled opencut areas and dumps indicates that total settlement has reached acceptable levels. The study involved the documentation of existing site environmental parameters and the delineation of site opportunities and constraints. The unpredictable nature of settlement over backfilled opencuts and overburden dumps represents the major constraint to urban development on mined areas.

Jan 1, 1987

By B Andrew, L Krois

Ground control systems, including ground control management, play an integral role in the effective and efficient extraction of copper ore at the Xstrata Copper û Mount Isa Copper Operations (MICO). Rock mechanics engineers and support technicians at Xstrata Copper have undertaken a wide range of investigations and actions over the past few years. Outcomes from this work have resulted in the evolution of ground control management practices on the site. Specific areas of improvement include the installation of efficient one pass ground control systems, greater application of sprayed concrete for areas requiring rehabilitation and the addition of new improved products, the removal of obsolete and less efficient products used in standard ground control practice. In some areas underground, the most effective methods to manage ground control hazards continue to be a variation on proven methods that have been in use for many years in the MICO. Ground control systems for developing through the basement contact zone are very similar to that developed in the late 1980s. Similarly, ground control systems have gone through repetitive evolution, whereby some systems fall in and out of favour subject to perceived costs. For example the pouring of concrete shuttering around drawpoints in poor ground conditions has recently been re-accepted as an effective means to manage this poor environment û despite having been previously cast aside as too expensive. Ground control management systems continue to evolve towards the goal of creating a workplace that is free of rockfall-related injuries and provide for higher levels of efficient and effective techniques by which ore is extracted from the ground.

Jan 1, 2005

By M Simanjuntak, A M. Supomo

PT Freeport IndonesiaÆs copper/gold operation disposes of approximately 222 000 dry metric tonnes of tailings per day via two thickeners. Reduction of the flocculant dosage rates in each of the tailing thickeners has been achieved with the installation of Clarometers«, modifications to the existing operating DCS control strategy and a change in plant flocculant. This has reduced the flocculant consumption rate in the last twelve months by approximately 20 per cent. It has also highlighted the disparity in the settling rates of the two thickeners. Collaborative efforts between Cytec technical site engineers and Freeport operational personnel have made possible the overall gains achieved in the tailings thickener optimisation.

Jan 1, 2003