Search Documents

By R Williams, P Godwin

In a time of changing rainfall patterns and in the light of recent tailings dam failures, there is closer environmental scrutiny for proposed tailings dam construction or expansion. Therefore the elimination of the traditional tailings dam could provide both environmental and cost benefits to an operation. One method to dewater tails is using pressure filtration to achieve lower moistures than what is currently available using other dewatering technologies. Further benefits include a higher rate of filtrate recovery, reuse of waste material and the potential for dry stacking of the filtered tailings cake, thereby minimising both risk and cost. This paper chronicles the replacement of two existing belt filter presses with a single McLanahan recessed plate filter press to dewater a tailings stream at a Bacchus Marsh site. It covers the slurry testing, equipment selection, installation, commissioning and operation of the filter press to achieve the following objectives:• removing the current tailings dam and slimes cells from the existing process to minimise failure risk and reduce the cost of a dam upgrade, as well as operational and maintenance costs• free up the surface area which was previously occupied by tailings dams and slimes cells• recover additional water to be returned to the process• reduce flocculent usage• reduce truck movements and handling.The project’s owner also expects to reduce carbon emissions by over 3000 t over the lifetime of operation as well as substantially reducing operating expenditure. By recognising the carbon reduction benefits, the project owner was able to successfully achieve partial funding through the Voluntary Waste Industry Protocol.An unanticipated, but as yet unquantifiable, bonus for the project was to seek an offtake agreement for the tailings thereby allowing the tailings to be considered a valuable source of beneficiated clay suitable for the construction industry.CITATION:Godwin, P and Williams, R, 2017. Pressure filtered tailings – environmental and cost benefits, in Proceedings MetPlant 2017, pp 324–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By J Borthwick, M Yusi, M Douge

Feasibility studies form a vital and significant component of the project delivery cycle. They are at the heart of the valuation process. This paper focuses on variables which can affect a project and how these are assessed as part of the decision-making process through feasibility studies. Test work and site selection needs; the degree of engineering required to meet the study requirements and the quality of owner project information are discussed. Also, local factors including permitting needs, social, environmental and government relations are considered. Engineering and site factors are crucial in the estimating process. The interaction of detailed engineering, engineering assumptions and estimating methodologies are therefore examined. The ownerÆs perspective is considered along with risk analysis, which is fundamental in project feasibility study activities. The impact of this is also discussed.

Jan 1, 2009

The design and operating characteristics of the hydraulic cyclone elutriator were described in detail by Kelsall and McAdam (1963), and the method of operation of the commercially available version, the Cyclosizer, is described in the manufacturer's pamphlet (Anon). Complete details of the operating procedure are given in the relevant operating manual (Anon, 1964).The cyclones which form the basis of the Cyclosizer (Fig. 1) under normal operating conditions produce typical cut sizes of 44, 33, 23, 15, and 10 µm for cyclones one to five respectively for material with a specific gravity of 2·7. At the end of the selected elutriation period each sized fraction is discharged and collected for subsequent assay or analysis but all material rejected by the fifth cyclone (e.g. minus 10 \lm quartz) normally passes to waste. When this material is needed for separate study, although its amount and average analyses can be calculated by difference, it may be necessary to collect more than 250 I. of very dilute suspension, flocculate the solids, allow to settle, and decant off the supernatant liquid.This procedure is cumbersome and inconvenient and the simple technique to be described may offer some advantages. The temperature of the water fed to the Cyclosizer is maintained at a constant value for added reproducibility.PROCEDUREThe present overall treatment of the subsieve material (minus 37 \lm) fed to the Cyclosizer incorporated several refinements compared with normal operation and these may be best illustrated by anactual example. Material to be cyclosized (25 to 100 g depending on size distributIOn and specific gravity) is completely dispersed in water at 23 QC by vigorous stirrmg, using suitable dispersants if necessary, in a...

Jan 1, 1974

By Fallins J

THE John Darling Colliery, owned by The Broken Hill Proprietary Company Limited, is situated 12 miles south of Neweastle, NSW and about 1 mile from the ocean. The area of the holding is approximately 10,000 acres, about half of which underlies the Pacific Ocean. The area was proved to be coal bearing by diamond drill boring: this method not only proved the coal to exist, but gave the depths from which could be calculated. It also proved the existence or otherwise of heavy faulting, which is a very important factor in the design of the underground lay-out of a mine. The location of shafts had to be carefuIly studied, and, before final selection, the following salient points had to be considered:Railway communications.Flood waters.Boiler feed water.Surface buildings.Probability of coal washing.Underground haulage arrangements.Lengths of roadways from a ventilating viewpoint.Before the shaft sites were finally selected, an underground design was prepared to determine the direction of the main drives in relation to the boundaries of the holding, and the of the coal seam: the latter, being an important factor in this particular locality, was ascertained by a geological survey of rock outcrops in the neighbourhood. Size of shafts was the next subject for consideration. This was determined by output, number of seams to be worked, amount of ventilation required, and, on...

Jan 1, 1930

By M A. Gontalves, A F. D C Varajpo, S A. Stachissini

Clays from the Santa Elena Peninsula, south-east of the Ecuador coast, were investigated with a view to identifying their main mineralogical, physical, chemical and textural characteristics as well as their potential for industrial use as adsorbents. Identified as calcic bentonites, two representative samples from the Tosagua Formation (Oligocene to Lower Miocene) were selected for acid activation trials. The selection criterion was based on the greatest amount of clay fraction (<2 ¦m fraction) associated with the greatest content of montmorillonite. For the activation treatments, HCl and H2SO4 solutions of 4, 6 and 8 N were used in a stirred glass reaction vessel with the clay sample under reflux during four hours at temperatures of 70¦C for HCl and 85¦C for H2SO4. Mineralogical analysis by X-ray diffraction (XRD), chemical analysis by X-ray fluorescence (XRF), differential and gravimetric thermal analysis and measures of density, surface area and porosity indicated the changes occurred in the crystal structure of the montmorillonite. The acid treated clays were utilised in trials of purification and decolourisation of soybean vegetable oil in a ratio of 2:100 (clay/oil) at 90¦C for 30 min, under constant stirring. After centrifugation of the suspension, the wavelength of the bleached oil was measured by UV-visible spectrophotometer and the bleaching capacity of the clays was determined. The best bleaching capacity of the samples was obtained with 6 N H2SO4 acid-activated clays. The bleaching capacity was compared to Tonsil, a commercial acid-activated clay and similar results between them evidenced the potential industrial application of the Ecuadorian clays to bleaching of vegetable oil.

Jan 1, 2008

By M Scamardella

The CSA Mine is located at Cobar, New South Wales, where it was in continuous operation from 1966 to the time it went into receivership on 29 January 1998. When it closed it was under the ownership of Golden Shamrock. Glencore International, in conjunction with Mt Lyell Mining, undertook a due diligence study to determine the feasibility to re-open the mine. This envisaged operating CSA Mine as a low-cost, copper concentrate producer under the direction of Cobar Management Pty Ltd (CMPL). The new workforce would consist of contractor trades people in operating functions under the co-ordination of CMPL staff, both on the surface and underground. This was the key to establishing the new culture in the workforce. The orebodies at CSA Mine are steeply dipping with copper-lead-zinc mineralisation in zones of strong alterations in a fine-grained siltstone host sequence. The predominant economic minerals are chalcopyrite, sphalerite and galena. The major gauge minerals are pyrrhotite, pyrite, chlorite, sericite and quartz. Ore for the project is being developed and mined from two high grade copper lenses within the QTS North system. Chalcopyrite occurs in two forms. The first consists of coarse chalcopyrite grains in association with pyrrhotite or pyrite. The second form consists of chalcopyrite grains intergrown with pyrrhotite grains. This form of chalcopyrite is quite rare. It allows electrochemical interactions between grains, resulting in rapid oxidation of the chalcopyrite surface. Physically this ore looks like, and has been mistaken for æpeacock oreÆ, ie bornite, but is infact oxidised chalcopyrite.

Jan 1, 2000

The Newmont Waihi Operations are centred on the Martha mine at Waihi, New Zealand. The mine has produced over 6.6 million ounces of gold from both openpit and underground sources since operations began in 1878. The current open pit operations commenced in 1988 and in the year to 30 June 2002 produced 129,790 ounces of gold at a cash cost of USD122 per ounce. This paper provides an overview of current operations and future directions.

Jan 1, 2002

By L M. Zhang, T H. Xu, J Zhao

Blasting is one of the most commonly used strategies for excavation in civil and mining engineering. Yet blasting can also bring along such undesirable effects as ground vibrations and soil disturbance. Numerical analysis is a powerful tool for estimating the effects of blasting and improving blasting design. In this research, a constitutive model for sand is proposed for the numerical analysis of blast-induced ground motions and wave propagation in soil mass. In the model, three model surfaces, ie the critical surface, the dilatancy surface and the bounding surface, are defined following the bounding surface hypoplasticity framework. The strain rate is included explicitly into the model formulations so that the proposed model is valid under high strain rate loadings caused by blast-induced vibrations. The performance of the proposed model is validated by the simulation of drained triaxial compression tests conducted on a crushed coral sand under different strain rates.CITATION:Xu, T H, Zhang, L M and Zhao, J, 2014. A bounding surface model for sand subjected to blast-induced vibrations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

About 74% of global seismic energy release occurs in the Circum-Pacific zone. Worldwide, about 71% of seismic energy release is in the form of shallow earthquakes, 27% as intermediate, and 2% as deep earthquakes. Seismic energy release is variable in time and has been shown to correlate with the amplitude of the Chandler wobble. It was high during the period 1949 to 1967, and is now at a rather low level, with the latest earthquake over M = 8.0 having taken place in Indonesia in 1971. The average worldwide recurrence rate for the expected largest magnitude earthquake (M "9.5) has been estimated as several tens of years, in marked contrast to the several tens of thousands to hundreds of thousands of years separating the largest volcanic eruptions. Geological studies are needed to establish reliable mean intervals between large earthquakes, and to detect the e;:istence of long-term fluctuations in the ste of occurrence. Seismic gaps have proved seful in static forecasting of large earthquakes, by identifying places where closer study of the variation with time of seismicity, deformation, and other parameters, may lead to the dynamic p_ediction of time, place and magnitude of earthquakes. The model of stress concentration at asperities explains the main features of seismicity in the Circum-Pacific. Slow earthquakes have been detected instrumentally, notably an event immediately preceding the 22 May 1960 Chile earthquake, the largest this century. It seems likely that this type of deformation may explain both instrumentally detected and macroscopically observed pre-seismic deformation, as well as unusual animal behaviour reported before some earthquakes. Seismic and volcanic events are interdependent, with large earthquakes commonly triggering eruptions. Melting of rock and intrusion of magma is likely to accompany many earthquakes.

Jan 1, 1987

By L. Gilbert

Recent changes to environmental legislation and trends in the environmental regulation of mining in the Northern Territory are being driven by (among other factors) Federal Government policies and international agreements on the environment. These trends are discussed and the expected application of the NT Water Quality Management Strategy (based on the National Water Quality Objectives) over the next few years is examined with respect to mine environmental management practices. Some of the potential conflicts and changes in approach which may develop are identified and examples discussed. Proactive means of integrating trends in environmental legislation with mine planning and waste management are discussed.

Jan 1, 1994

By G Ferguson a, P Carrasco, P P. A Dowd

International codes of practice offer broad definitions with respect to the classification of resources in terms of risk. Specific guidelines and protocols, to analyse sample data, carry out geostatistical appraisals, develop geological models and finally estimate and classify resources, are not addressed. Neither are detailed requirements for engineering mineable reserves from estimated resources. In addition, international codes of practice fail to distinguish between types of deposit, other than in broad terms, as for example, The AusIMM JORC Code (JORC, 1999) which makes reference to diamond and coal deposits. The objective of this paper is therefore to set in motion the process of specifying detailed protocols, acceptable to the international community, for the assessment, reduction and management of risk associated with the development and extraction of mineral deposits. Ordinarily, the main risks and issues encountered during the process of estimating resources and subsequent conversion to reserves, encompass:failure to understand relevant geological controls of mineralisation; validation of grade interpolation; optimism in geotechnical appraisals of dilution and stability and the consequent selection of inappropriate mining methods; metallurgical modelling of minerals and contaminants reporting to concentrates; appraising the hydraulics of heap leaching and the numerous factors that can affect recovery; difficulty of managing metal price cycles and changes in regulations within the constraints of long-term mining plans; and development of better evaluation techniques for mining ventures. Uncertainty is inherent in estimation and engineering work, and its identification, reduction and management should be a fundamental goal of all involved in the mining industry (Figure 1). Variability may be reduced by:following internationally accepted practices for the collection, manipulation and analysis of geoscientific data; and verifying that the procedures actually performed meet the associated standards. Increasing amounts of data will also reduce uncertainty, but only if the procedures used to collect and appraise such data follow the relevant procedures. It is thus the aim of a series of papers in preparation, Beniscelli et al (in prep), to put forward detailed guidelines, for:project sponsors û to provide a global view of the work and documentation needed to support requests for funding various phases of project development and budget approvals; geologists û to indicate a checklist of the requirements and standards for the exploration and estimation of resources; and engineers and economic analysists û the protocols for characterising, modelling, engineering and evaluating the extraction of reserves. It is therefore hoped to encourage the development of consistent standards for declaring reserves within the mining industry. Data from projects and operations will be utilised to illustrate the benefits of adopting a rigorous approach to estimating resources and engineering reserves, Beniscelli et al (in prep).

Jan 1, 2000

By T Sasaoka, H Shimada

Mined-out limestone/aggregate quarries in Japan contain many high and enormous pit walls. Many precious resources are abandoned in these final pit walls. In addition, there are many mines which are located in or near populated areas in Japan. Utilisationof the potentially useful under- ground space at mined-out sites is a topic relevant to the practice of surface mining. This paper describes and discusses the concept of underground space utilisation and tunnelling systems, referring specifically to geotechnical/ tunnelling parameters.

Jan 1, 2008

By Allchurch P. D

At Perseverance a reserve of 45 million tonnes at 2% Ni was indicated by drilling. Holes were drilled in trellis pattern on section lines 61m apart to assess shallow mineralization. To explore at depth holes were spaced 122m apart, collared vertically, then allowed to deflect under controlled drilling conditions. The mineralization may be divided into the three homogeneous classes of soarsely disseminated, heavily dissem- inated and massive sulphides. In the standardised sampling and assaying procedures used to assess the deposit, attention was always paid to these fundamental ore types. All sampling and assaying processes were continuously monitored by checks. Sampling and sample preparation errors were small, to judge from the differences between results of original and check samples. Assaying errors, determined from analyses made by independent laboratories using different methods, slightly exceeded sampling errors. Comparison of underground core, c'iannel, and grab sampling, suggests that core sampling tends to undervalue.

Jan 1, 1976

o Resource production is essential for society. o Demand for resources will increase as population grows.o Resource industries are the main consumer of trained geologists.o The lead time from(1) training to productivity(2) research to resource production is measured in years.o An adequate supply of well trained geologists and successful geological research is an important agent in ensuring cost effective, adequate supply of mineral resources for society. Therefore the main beneficiary of geological education is society itself.o Society is paradoxically apathetic or antagonistic to the resource industry because (1) it represents change(2) lobby groups working for other causes have successfully moulded a bogey man image for the resource industry in the public eye.Professional training and research for resource industries consequently lack popular support. Funding is at an absurdly low level in comparison with the economic importance of resource supply.

Jan 1, 1990

By S E. Wallah, D Hardjito, B V. Ran

The manufacture of Ordinary Portland Cement (OPC) is not only energy-intensive but also releases a significant volume of carbon dioxide (CO2) to the atmosphere. In addition, OPC in concrete often causes premature deterioration that affects the durability of concrete structures. This paper explores an alternative to OPC concrete called geopolymer concrete.The present research utilises low calcium (class F) fly ash as the source material to produce geopolymer concrete. Several factors that affect the mix design process such as mix proportion, curing time, and curing temperature have been studied. In addition, the long-term properties such as drying shrinkage, creep, and exposure to sulfate attack are also being investigated.The test data presented in this paper reveal that geopolymer concrete possesses high compressive strength, undergoes very little drying shrinkage and moderately low creep, and shows excellent resistance to sulfate attack. The result is extremely promising and demonstrates the sustainability of geopolymer concrete as a construction material for a sustainable future.

Jan 1, 2004

By H Aoki, A Nakayama, K Morita, S Yamada

The thermal conductivity of mold flux is crucial for optimising the productivity and quality of steels. This study investigates the thermal conductivity of molten oxides, including CaO-BO1.5-AlO1.5 (CBA), CaO-BO1.5-AlO1.5-SiO2 (CBAS), and CaO-MgO-BO1.5-AlO1.5 (CMBA) melts, using a hot wire method. Additionally, their structure is examined using Raman spectrometry and magic angle spinning nuclear magnetic resonance (MAS-NMR) to explore their relationship. Furthermore, first-principles calculations are employed to assess the covalency of each bond in the melts for a more quantitative analysis of their relationship. The study confirms that an increase in the CaO concentration of the CaO-BO1.5-AlO1.5 melts reduces the amount of bridging oxygen and consequently decreases thermal conductivity. The covalency of the B[4]-O bond is highest, especially when the second-nearestneighbour Al atoms transition from Al[6] to Al[4], forming the AlB3O7 structure with B[4]. The relationship between thermal conductivity and the structure of CaO-BO1.5-AlO1.5-SiO2 melts can be quantitatively assessed using the degree of polymerisation of the network structure and the variation of covalency as indicators. Furthermore, replacing CaO with MgO in the CaO-MgO-BO1.5-AlO1.5 melts reveals a mixed alkaline earth effect on thermal conductivity.

Aug 21, 2024

By Thompson M

The humble gabion basket is to mine development what the light bulb and safety pin are to eir-ryday life. Gabions provide a flexible, easy to assemble and cost efficient solution for "101" mine and civil engineering development applications.In some instances gabion baskets are still efficiently in use after many years of faithful, maintenance-free service. In other situations, the baskets have been demolished or made redundant within days, either having served their temporary usefulness or negligently destroyed by the operator of heavy equipment. Either way, the gabion basket must surely rate among the top 10 cost efficient engineering construction materials.

Jan 1, 1994

By B Ascott

As a prerequisite to achieving integrated regional production reporting across multiple sites, Newmont Australia initiated a project to standardise the configuration and use of mine control systems at three underground sites. This paper outlines the project and considers the outcomes which, in a number of cases, have exceeded the original objectives.

Jan 1, 2008

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

The scope, pace and depth of mining is creating a need for improved ground control strategies to meet mine safety standards. Ground control and associated conservation problems relating to subsidence and the disposal of mining and metallurgical wastes can be resolved by mine filling with selected reject materials. The lack of suitable criteria to evaluate the applicability of such materials and especially cemented forms of fill is considered. Sulphide wastes, which are prone to oxidize, and cement are inexpensive mine fills, but their incorrect use can give rise to problems which are briefly described. Research work concerned with the utilization of sulphide wastes such as mill tailings, to produce fill with self-cementing properties has shown that the development of cohesion and strength is attributable to natural oxidation processes controlled by the physical and chemical composition of the fill mass. The cementing is caused by a number of oxidation products, and is most effective when the mineral pyrrhotite is present. The concepts of fill design are outlined and various criteria for assessing durability and deformational properties are proposed. Specimens prepared in the laboratory are capable of attaining unconfined compressive strengths up to 28 MN/m2.

Jan 1, 1973