Search Documents

Published information on technical and market developments in the uses of zinc tends to dwell very largely on two groups of uses of zinc - zinc coatings (mainly galvanising) and zinc casting alloys. These two groups account for two-thirds of primary zinc consumption. However, if total zinc consumption is taken into consideration, coatings and casting account for a little over half the total. Either way, the health - or otherwise - of these 'other' uses of zinc can have a substantial effect on the industry as a whole. The aim of this paper is to put the whole market picture for zinc into better focus, concentrating on the factors which can affect consumption in the 'other half' of zinc's markets: ò brass - the third most important market for zinc at around one million tonnes - responds to changes in the economic cycle. It has seen substantial changes in the balance between different forms of semi products, and, in Europe at least, some real market gains; ò zinc sheet - one of the original uses of zinc in Europe - has grown substantially in some countries, but remains almost unknown elsewhere; and ò zinc pigments and compounds are so numerous that - barring the substitution of zinc oxide in rubber - major overall changes in the market are unlikely. The paper examines these markets and assesses their potential and implications for zinc markets as a whole.

Jan 1, 1993

Following unprecedented high market prices for tin and gold in 1980, significant advances in both mining technology and geological knowledge took place in northeast Queensland. These led to a rapid growth in mining activity. Production of these traditional metals reached levels comparable to those of the heyday of mining activity at the turn of the century.Although tin and tungsten prices have since collapsed, the geological knowledge gained and significant discoveries made during the boom, have created a potential for mine development when prices rise again. For other discoveries which are not workable because of treatment problems, future technological advances are required to raise their potential.

Jan 1, 1990

By Biao Q, Mizuta Y

Thermal constants such as thermal con- ductivity and thermal diffusivity of rock and coefficient of heat transfer of airway wall are the most important characteristic values which decide accuracy of prediction calcula- tion. However, quality of rock is not homoge- neous and water content in rock varies with location and so, a method for in-situ measure- ment of thermal constants must be taken in. The method developed by us is to measure in- situ rock temperatures at two different depths from airway wall. It is simple and we found its accuracy is good enough in the engineering Sense.

Jan 1, 1988

By Katsuyama K, Nag DK

Three aspects of rock mechanics, namely, in-situ stress estimation by acoustic emission (AE) method, strength of rock mass and role of chemicals to reduce the strength are covered. It is possible to detect the previously applied maximum stress by stressing a rock specimen to the point where there is a substantial increase in AE activity. This is known as Kaiser effect. From the AE signatures in the second and subsequent loadings, AE take-off point was identified more easily than in the first loading. In determining the compressive strength of rock mass, two factors have to be considered, namely, the size effect on the compressive strength of intact rock and the effect of discontinuities on the compressive strength of rock mass. Although a modified Bieniawski criterion gives best agreement with the triaxial test data, modifications have been suggested to Hoek-Brown criterion due to its popularity. It is possible to reduce the tensile strength of sandstone by saturating it with weak chemical solutions made with dodecyltrimethyl ammonium bromide, polyethylene oxide and aluminium chloride by up to 30%. In the case of compressive strength, there is no appreciable effect. The possible explanation is that the chemical solutions produce an effect on the strength of sandstone only when the failure mechanism is dominated by tensile mode.

Jan 1, 1998

Sixty years after its inception, after an alternation of periods of admiration and rejection by the industry, Sampling Theory can now be seen as going through its golden age. A brief history of its successive transformations and progresses achieved by its author, Pierre Gy, and his followers, reveals the theoretical as well as practical difficulties that had to be vanquished to reach this point. Its current level of acceptance and corresponding trends are discussed and illustrated, with an insight on its increasing real role in the industry and future prospects for its further development.

Jan 1, 2008

THE millng methods employed in the Mount Lyell Mining and Railway Company's mines are, perhaps, less known to the milling world than those of other important districts, due to the geographical remoteness and isolation of the Mount Lyell field,but they present many features which are unusual, and should be of interest to the mining engineer. Typical mining is carried out on an open-stope system, details of which are the result of local experience and evolution, and of which the outstanding feature is that the ground is so worked as to be largely self-supporting by virtue of domical form given to the stope roofs. It is locally termed "rill" stoping,' but differs widely from what is generally understood by that designation, chiefly in that the "rill" or slope is developed in every direction from a central focus, and not merely in directions followllig the strike of a lode or ore-body whose longitudinal dimensions are very much greater than its width. Such terms as "donie stoping" or "arched-back stoping" would be more appropriate and descriptive.The company's active operations' at the present time extend to the Mount Lyell and North Lyell mines, and, though the fundamental principles of stoping methods are the same in each, the dissimilarity of the ore-bodies, both in nature and mode ofoccurrence, necessitates considerable variation as to details to meet the respective conditions. The Mount Lyell pyritic body lends itself to the adoption of the .system in its simplest and almost ideal form, and a description of stoping in this mine willserve best to illustrate it, while later reference to details of practice in the North Lyell mine will indicate how it may be varied to meet more difficult circumstances.

Jan 1, 1915

By Brown GA

Results are presented which demonstrate the feasibility of employing electrolytic membrane technology to process leach liquors derived from alkaline pressure leaching of scheelite concentrates and to recover and recyle sodium carbonate. Thus the problem of disposal of sodium sulphate is avoided. In a further application of the technique sodium tungstate is converted to tungstic acid which can be further processed by three possible routes to crystalline or amorphous tungstic acid or tungsten powder. In each route sodium hydroxide is produced which on carbonation can be recycled as soda ash to the pressure leach stage. Further testwork is required to determine long term operational conditions in the membrane cell and to confirm the effect and deportment of impurities on products. The process has been patented.

Jan 1, 1986

An integrated computer system (the Short Term Mine Management System) has recently been developed by B.H.P. Steel Long Products Division in Whyalla, South Australia for use in their open pit iron ore mines.The system incorporates blast design, comprehensive blasthole data handling, grade coilrol, stockpile scheduling and management and reconciliation within a single, user friendly computer package. The blast design system allows the blasting engineer to design the layout of holes for a production blast using geological information projected from the bench above to aid in appropriate blasthole positioniog in particular rock types. The grade control system allows mining blocks to be designed and evaluated from blasthole information using interactive graphics processes. The handling, storage and reporting of blasthole survey, assay and geological logging data forms an integral part of this system. Stockpiles can be constructed from a number of mining blocks to reach a specified target grade using the stockpile management system. Although not yet integrated, the reconciliation system will reconcile stockpiles back to mining blocks and to the geological model.

Jan 1, 1990

By McPherson M. J

This paper describes a major ventilation study for the expansion of the El Teniente mine operated by Codelco, Chile. El Teniente is one of the world's largest under- ground mines. The design effort was under- taken in three stages and involved a partial mine ventilation survey with network simula- tion, detailed stope ventilation investiga- tions, and design of the entire mine ventila- tion circuit based on production plans to achieve 112,000 tons per day by 1995. The partial ventilation survey provided values of representative friction factors and resistances for typical ventilation raises and airways. These values were used to conduct detailed modeling of the block caving levels to investigate the most cost effective and practical means of providing the required ventilation. The results of these analyses were extrapolated to the proposed expanded mechanized zones.

Jan 1, 1988

By M Wortley, A Cantarutti, G J. Clarke, C

As part of a broad program to optimise the performance of their grinding circuit, BHP Billiton Cannington have installed an OCS¬ Expert system together with three VisioRockÖ online particle size analysis cameras. The main purpose of the system is to stabilise grind size and feed to the flotation circuit. This particular application of OCS¬ is the first installation to incorporate Metso Minerals Process Technology-Asia PacificÆs (MMPT-AP) Dynamic SAG/AG Mill Model, which is able to predict numerous mill parameters that were previously unable to be measured with the existing plant instrumentation. Integrated into the logic of the control algorithm are online vision based, particle size measurements of the AG mill feed and recycle crusher product. This paper will describe the history of the project from initiation to date, the model and OCS¬ logic configuration, and demonstrate the significant benefits realised at Cannington mine.

Jan 1, 2007

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. J. G. SYMONS) IN PRESENTING THE CERTIFICATE TO ROBERT COLVILLE BRADSHAW, O.B.E.Today it is my privilege and pleasure to introduce to you, Robert Colville Bradshaw. O.B.E., the third New Zealander to be honoured with Honorary Membership of The Institute. Sir William Hudson and Mr. C. H. Benney were the others.Mr. Bradshaw has been an Affiliate Member of The Institute since the formation of the New Zealand Branch in 1966. Like his friend Matt Benney. Bob Bradshaw is an accountant by training. Last June he retired as senior partner of the firm of chartered accountants, now known as Wilkinson Wilberfoss, with which he served from January 1929.Mr. Bradshaw grew up in New Zealand attending the Terrace School in Wellington, the New Plymouth Boys' High School where he was a boarder, and completing a Bachelor of Commerce at the university now known as the Victoria University of Wellington. He is an elected Fellow of the New Zealand Society of Accountants and an Associate of the United Kingdom Institute of Cost and Works Accountants.

Jan 1, 1977

By Coin CDA

From a study of coke samples obtained from the tuyere level of four Australian Blast Furnaces, the nature of in-furnace coke degradation has been investigated. At the periphery of the raceway is a concentration of fines and the lump coke appears dull and rounded. However coke from the deadman is angular and relatively undegraded. Cokes made from higher rank coal appear to suffer preferential attack of the reactive maceral derived component (binder). The coke from lower rank coal appears to be attacked non-preferentially by the solution-loss reaction. Initial attempts to simulate these phenomena have given results consistent with these findings. From chemical analysis of the tuyere probe samples there appears to be a relative increase in carbon and decrease in-.sulphur and phosphorous between stockline and tuyere level. An overall decrease in coke mineral matter derived material was noted and associated with this was a significant gasification of silicon. Consequent formation of silicon carbide was noted.

Jan 1, 1981

Utah's Blackwater mine began operations in 1967. The four CQCA mines controlled by Utah followed over the period 1971 to 1979. Project feasibility studies for all these were based on open cut mining to overburden depths of 60 metres, with typical project lives of 12 to 16 years, depending on reserves Further studies, initiated after the mines had started, showed that continuation of open cut mining beyond the 60 metre highwall was viable. In 1973, the Deep Stripping Project (DSP) was launched to define the scope for stripping deeper, to determine what the additional equipment needs might be, and to pu forward proposals for a full scale trial system. The project commenced at grass roots with a literature survey, proceeded through a sequence of equipment evaluation, specification, design and manufacture to the commissioning of the Goonyella BWE system. Studies are continuing to assess the future deep stripping requirements for all Utah's Bowen Basin mines.

Jan 1, 1983

By Lu S, Jiang Y

The conventional transportation system in open pit, a to u.* itc:,~> truck., to carry the ore along the ramps. Normally, the transportation distance increases greatly as mining progresses deeper. A new approach to overcome the above disadvantage is to adopt a buried roadway by which ores is transported by conveyors from the mining area to the outside dump in the shortest distance so that the production efficiency is greatly increased. Maintenance of the buried roadway in a good working condition is the key factor that determines the success or failure of the proposed approach. This includes the determination of support load, types and structures of support and other related supporting measures. The crucial problem here is to effectively control the load applied on the buried roadway in a certain range that the ordinary support can stand. Based on the theoretical analysis, numerical modelling and physical simulation testing using equivalent material, this paper studies effects on control of the support load by adopting certain measures, for instance reinforcing the surrounding rock and placing the extendable layer between the support and a rock mass. Furthermore, the influence of the dynamic load induced by the movement of heavy vehicles on the stability of the buried roadway is also investigated.

Jan 1, 1995

By I Kolomaznik

Each technological process can be reduced on the transport networks, and namely on the parametric networks and the non-parametric ones. The parametric networks are created by the piping, electrical cables or channels. The non-parametric network is created by the ways, suspended grooves, trackages and also by the belt conveyors or other conveyors for continuous material transport. If we reduce the technological process on transport networks, then, by the creation of these networks models and their mutual interconnection we obtain the model of the whole technological process. The model can be understood as the universal one, without exaggeration, because it is valid for any technological process. However, for us the mining production process is important what represents the mining and transport of raw materials under the support of the ensuring system. In this contribution one of the first attempt is described, and namely how to connect the parametric network which has been already worked out very properly with the non-parametric network what is presented in this contribution by the transport line of belt conveyors.

Jan 1, 2003

MR. L. C. BALL, chief government geologist, Queensland, wrote: This paper is intended as a severely mechanical exposition of the means adopted to deal with tremendous inflows of water concurrently with development and exploitation; but incidentally it serves as a splendid exposition of close co-operation maintained between the geological and engineering branches of this large organization.I have been impressed by the completeness of the mine plans of 'Mount Isa Mines Ltd.; but only such a paper as this has brought fully to my understanding the difficulty and complexity of the solid geometry involved in the detection and plotting of the orebodies and their stratigraphic control, including faults and large-scale brecciations, and the managerial foresight that set going the initial investigations.The company's geological branch of course must be given full credit for the results attained, but it gives me pleasure that the Geological Survey of Queensland has been closely associated in much of the study.It is noted that complete drainage was affected, but it would be interesting to learn whether the brecciated zone will again become waterlogged and whether from above or from below, and whether there has been any change in the dissolved mineral content of the water as the work progressed.

Jan 1, 1939

By Vanderberg B

A 3D, PC based computer program is currently under development by Blasting Analysis International, Inc., to analyze the kinetics of full scale blasts with two or more high-speed motion picture cameras. Todays common approach of utilizing only a single camera system can, in some cases, lead to great errors and erroneous conclusions when motion is assumed to be in a predefined plane of motion. CMe phrase, "What you see is what you get, it no longer true in 3D."). This is especially true in blasting environments which exhibit complex and/or predominant structural geology. The 3D system eliminates this problem, and includes automatic corrections for vertical and horizontal camera optic axis orientation, dimensional controls, lens distortion, field set-ups, projection imaging and digitized inputs. The only information required is the surveyed or known coordinates of at least six non coplanar points in the field of view. Motitn from each camera view is then digitized, transformed through a direct linear transformation, and processed with the 3D software, which also automatically time matches the data, even when the high-speed cameras are operated at different speeds. Eleven calibration constants are generated using an overdetermined system of linear equations to output the true 3D coordinates of motion in the time domain. Applications for this 3D approach are not restricted to just analyzing the kinetics of a blast. The system is sufficiently flexible to allow an accurate, quick and economical method of bench face profile analysis, generate muck pile profiles and estimate volumetric calculations. The recording systems for these applications can be common 35mm still photography and/or video equipment. It is envisioned that this system will soon replace expensive laser surveying systems at a fraction of the cost in the near future. It is also an excellent system to accurately quantify drill pattern layouts and the spatial locations of each blasthole. This information is required for generating single hole based synthetic seismograms to accurately predict the vibrational outputs of full scale blasts. In terms of litigation concerning claims resulting from blast induced ground vibrations to structures, the system is proving to be an excellent and economical method of performing pre-blast surveys where differential settlement is suspect.

Jan 1, 1990

The automatic control of grinding mills for optimum performance is an area of control which can benefit from new control concepts and technology. Economic pressures dictate that the mining industry undertake changes in process design, control system strategy and operations organisation that call for innovative reappraisals of the control system performance necessary to enhance the functions of the process operator. As more dependence is placed on instrumentation the chances of abrupt, total loss of process control through an entire production complex becomes a major concern of the plant manager.

Jan 1, 1978

JUDGING from the attitude of past and present Parliaments in Australia, it is a' reasonable assumption that encouragement of the principal industries has been adopted as a main principle in the government of the country, but while in most cases bonuses, subsidies, and other means have been proved successful and become recognized as established methods in the case of mining, which is undoubtedly one of the most important industries, the question is complicated by difference of conditions and variable quantities, and it can scarcely be said that any system has been proved generally successful. Indeed, it would not be a very extravagant statement to assert that problems connected with affording direct monetary assistance in aid of mining development, and at the same time devising a system adaptable to the varying conditions to be met, are, in every State of the Oommonwealth, matters continually exercising the minds of those concerned in providing and ailocating such assistance ie Parliament on the one hand, and the Department of Mines on the other.True, there are methods in vogue of granting State assistance to the mining industry which have undoubtedly been successful, but it is in most cases questionable whether the beneficial results following successful expenditure in one direction have compensated.

Jan 1, 1911

The Copper Concentrator at Mount Isa Mines Limited treats approximately 6 Mt of chalcopyrite ore annually. The ore is currently sourced from the 1100 and 3000 orebodies at Mount Isa. Chalcopyrite is the only significant copper bearing mineral, with pyrite, quartz and dolomite being major gangue minerals. Ore is typically 10% chalcopyrite, 11% iron sulphides and 79% non-sulphide gangue. Copper ore is treated through two autogenous mills, two ball mills and a flotation circuit. The autogenous mills replaced a crushing plant, two rod mills and two primary ball mills during 1991. For routine analysis of concentrator performance, composite samples of mill feed, final concentrate and tailings are generated every 4 week period. All samples are sized and size fractions are assayed. Recovery of mineral species to the concentrate are then calculated for each size fraction. Sometimes liberation analysis was also performed by QEM*SEM (Quantitative Evaluation of Material by Scanning Electron Microscope).

Jan 1, 1990