Search Documents

By Ken Dyck Sr.

"Construction of the Cigar Lake uranium mine in northern Saskatchewan is well under way. Production is anticipated to begin in the first half of 2007. When in full production, the mine is projected to produce a net 18,000,000 pounds of U3O8 per annum from a high grade ore averaging approximately 20% U3O8.Water management was a major issue that required substantial effort in the Cigar Lake design. Not only is effluent quality controlled, a tight water balance to minimize effluent volume is also designed into processes in order to minimize environmental impact. This paper focuses on the water treatment process and water handling equipment, as well as the operating philosophies that will reduce fresh water consumption to a minimum. An overview of the mining and ore handling systems, as well as aspects of controlling water production from the ore formation and the mine development areas will also be discussed.INTRODUCTIONThe Cigar Lake ore body has proven and probable reserves that total 232 million pounds U3O8. Cigar Lake is the world’s largest undeveloped high-grade deposit. It is the second largest highgrade deposit surpassed only by the McArthur River deposit another Cameco - operated mine in the Saskatchewan Athabasca Basin. Cigar Lake is owned 50% by Cameco Corporation, 37% by AREVA (COGEMA Resources Inc.), 8% by Idemitsu Uranium Exploration Canada Ltd. and 5% by TEPCO Resources Inc. When production starts in 2007, ground ore slurry from Cigar Lake will be shipped to the McClean Lake mill (owned by AREVA) some 80 km away. All of the Cigar Lake uranium will be leached from the ore at McClean Lake. During initial production ramp up, all uranium will be processed at McClean Lake to yellow cake (uranium oxide). After the average production has exceeded a 10 million pound per year rate, Cigar Lake uranium will begin to flow from the McClean Lake Mill to the Rabbit Lake Mill. At this point, subject to regulatory approval, 57% of the Cigar Lake uranium, in a uranium rich solution, will be transported to Rabbit Lake mill (owned by Cameco) for purification to yellow cake. A complete summary of the flow of uranium from the Cigar Lake ore body through to product at both McClean Lake and Rabbit Lake can be found in a recent paper titled “The Cigar Lake Project – Mining, Ore Handling and Milling” in the March 2004 issue of the CIM Bulletin. The paper was written by C.R. Edwards."

Jan 1, 2006

By Hua-Zhong Yu

Gold is one of the most widely used substrate materials for self-assembly. Self-assembled monolayers (SAMs) prepared from alkanethiols and their derivatives on gold are the most reliable and well-studied systems to date, which have attracted much attention because of interest in two-dimensional molecular assemblies, and of their potential applications in molecular devices, sensors, and functionalized interfaces. Gold electrodes are also very important in microelectronics and electroanalytical chemistry. This work reports the characterization of a new type of gold substrates for self-assembly. The gold substrates are constructed from recordable compact disks (R-CDs) with simple and straightforward wet-chemical treatment, and can be made at desired sizes and shapes that satisfy different experimental needs. In particular, an easy, inexpensive, and reproducible method to prepare self-assembled monolayers (SAMs) on CD-R gold substrates after removing the protective polymer films with concentrated nitric acid was described.

Oct 1, 2003

By Graham Davey

"Low speed stirred milling has been employed for many years in the metalliferous and industrial minerals industries. High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. By combining low speed and high-speed milling fine and ultrafine grinding efficiency and operating costs can be improved.The correct selection of different fine grinding technologies is covered, when each mill is applicable and when a combination of the VERTIMILL® Grinding Mill and SMD provides the best economic solution.INTRODUCTIONUltra-fine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits, around the world are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The traditional approach for gold containing refractory material has been to liberate the locked gold by chemically destroying the pyrite through oxidation. Roasting, pressure oxidation, and bacterial oxidation all employ various degrees of temperature, pressure and catalysis to react the pyrite with oxygen to produce iron oxide and sulfur by-products. However all of these methods are economically impacted due to specific operational added requirements and emissions controls. Pressure and bacterial oxidation have very high capital and operating costs."

Jan 1, 2006

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The slurry systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1500-2000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed with a larger diameter impeller and increased vane lengths, and is expected to triple Aurora’s mission length for hydrotransport pumps.INTRODUCTIONSlurry Pumps are Critical Equipment at SyncrudeSlurry pumps are a critical component in Syncrude’s operations. In a typical Aurora application, each pump stage helps move over 8000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1500-2000 hours, or 12-16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in higher than optimal impeller vane speeds for the service conditions.PROJECT BASISSlurry Pumps are the Reliability Bottleneck at AuroraSlurry pumps are currently the shortest-lived components that determine the overall system run length at Aurora, in Hydrotransport, Extraction and Tailings. Vibrating screens and piping had been previous bottlenecks, but their reliability has been improved through upgrades in equipment design and wear materials. Both vibrating screens and piping can now achieve 4000 hour mission lengths."

Jan 1, 2013

By Trevor Yeomans

"NVI Mining’s Myra Falls Operation is a forty year old underground mining operation feeding a 4000 mtpd concentrator.The current Mill, built in 1985, was designed to process a large massive sulphide ore-body. This ore-body, known as the “HW”, contains about 50% pyrite. Value minerals are chalcopyrite, and sphalerite, with precious metals occurring in all mineral types.By 1997, mining of a new ore-body, known as “Battle-Gap” commenced. Mineralogically complex, the new orebody contains about 15% pyrite, copper minerals including primary chalcopyrite, secondary bornite, chalcocite and tennantite, combined with increased galena and sphalerite.Flotation performance generally decreased with increasing amounts of Battle-Gap ore types, with both copper concentrate quality (increased lead and zinc content) and copper recoveries being affected.Following significant metallurgical testwork, a new fully sequential copper-lead-zinc flotation flowsheet and reagent scheme was developed.This sequential flowsheet was progressively installed and commissioned during 2006.Copper concentrate lead and zinc smelter penalty contents have been reduced by some 40%, whilst increasing copper recovery by 10%.INTRODUCTIONNVI Mining operates the Myra Falls Operation near Campbell River on Vancouver Island, BC. The complex has been in operation since 1966 with mining being predominantly underground. One unique feature of Myra Falls is that the mine operates within a BC Provincial Park.In 1985, a new large massive sulphide ore-body (HW) had been defined, and metallurgically tested. A new concentrator was built based upon this massive pyrite, chalcopyrite, and sphalerite mineralization producing copper and zinc concentrates by conventional flotation methods."

Jan 1, 2008

By Todd Smith, Brigitte Lacouture, Greg Anderson, David Lin

"The lead and zinc flotation circuits at Red Dog Mine are preceded by a preflotation circuit which recovers naturally-floating organic carbon contained in the ore. Organic carbon is a potential contaminant in the lead concentrate and is detrimental to lead-zinc selectivity. Prior to 2007, the Red Dog preflotation circuit consisted of a single stage bank of tank cells which floated the organic carbon. The preflotation concentrate was discarded directly to tailings, however, this stream contained significant amounts of lead and zinc. Zinc loss to preflotation ranged from 2% to 6%, relative to the zinc in the mill feed and was proportional to the amount of organic carbon in the ore. The main mechanism of the zinc loss was entrainment.Pilot plant and modeling testwork were conducted to examine the use of a Jameson Cell to clean the preflotation concentrate. Results indicated that up to 90% of the zinc deporting to preflotation concentrate could be returned to the flotation circuit for recovery. The installation of a 5.4 m Ø Jameson Cell with 18 downcomers was initiated in June 2006. The new preflotation cleaning circuit was commissioned in March 2007. Conservatively, preflotation cleaning has resulted in zinc and lead absolute recovery gains of 1.0% and 1.5%, respectively. The $9.1M project has a payback period of approximately 1 year at current metal prices.INTRODUCTIONRed Dog Preflotation CircuitRed Dog Mine is located above the Arctic Circle in northwest Alaska. It is the world’s largest zinc concentrate producer with a production rate of more than 1.0M t/yr. Red Dog is operated by Teck Cominco Alaska Incorporated under an operating agreement with the Northwest Alaska Native Association (NANA). Due to the remote location of the mine, it is accessible only by air, or seasonally, by ocean-going barges.The Red Dog deposit is a rich sedimentary exhalative (sedex) zinc-lead-silver deposit. The major sulphides, in decreasing order of abundance, are sphalerite, pyrite, galena and marcasite. Due to the complex nature of the ore body, run-of-mine ore is blended in stockpiles before being crushed and processed through the concentrator. The average mill feed grade for 2006 was 6.1% lead, 20.6% zinc, 8.0% iron and 0.67 % organic carbon."

Jan 1, 2008

By Ivan C. Machado

Jaguar Mining Inc. is implementing a 1.1 Mtpy, 7-year LOM gold project in the Iron Quadrangle (?Quadrilátero Ferrífero?), Brazil. Construction is on schedule and startup is programmed for Q2 2010. Mill feed grade averages 4.43 g/t and LOM gold production is estimated at 800,000 oz. The project entails two sulfide underground mines and three oxide/transition open pit mines. A state-of-the-art flotation/gravity concentration/CIP Plant has been designed based on testwork carried out by internationally recognized Canadian, U.S., and Brazilian laboratories. The mass recovery of the flotation section is only ca 10%, while its gold recovery is about 90%. Therefore, the CIP-ADR Plant will treat only 10% of the solids mass contained in the mill feed, while 90% will be fully cyanide-free material that will be partially used to feed a Backfill Plant. The leached tailings will be conveyed to a rather small tailings dam, whose 20- m3/h supernatant solution will be treated by a new electrolytic technology. The plant design contemplates a High Density Thickener for the cyanide-free rejects exceeding the backfill demand and a Regrinding Section before the Leaching Circuit. The estimated overall metallurgical recovery sits around 92%. This paper focus on the use of modern technologies to reduce costs, risks, and liabilities.

May 1, 2010

By Owen Matthews

THE property of Cochenour Willans Gold Mines, Limited, is in Dome township, Red Lake area, northwestern Ontario, a hundred miles north of Kenora and close to the Manitoba border. 'Planes of Canadian Pacific Air Lines, Limited, serve the district daily, except Sundays, from Kenora, Ontario, and Lac du Bonnet, Manitoba, passengers being trans-ported from Winnipeg to Lac du Bonnet by car. Freight is handled by the Patricia Transportation Company. It is brought in from Hudson, Ontario, on the Canadian National railway, in summer by water and in winter by tractor trains over the frozen lakes. The first staking on the property was done during the 'rush' of 1926 and 1927 by William M. Cochenour, and on April 30th, 1928, a syndicate was formed, taking in claims of W. M. Cochenour and Dan Willans and H. G. Young. Surface trenching was carried on almost continuously until 1934. In October, 1932, Ventures Limited took an option on the property, and in December of that year they carried out an extensive diamond drilling programme, but considering the results did not justify further work, they relinquished the option. In July, 1934, further surface work was carried out under the supervision of W. P. Mackle and, on the strength of his report, Noah Timmins Incorporated took an option on the property and agreed to make an initial expenditure of $100,000 on development work. This was carried out under the direction of Hollinger Consolidated Gold Mines and included the sinking of a shaft to a depth of 165 feet, establishment of a level at the 150-foot horizon, and some 1,900 lineal feet of drifting and cross-cutting. The results obtained from this work were not considered of sufficient promise and the option was terminated in August, 1935. Mr. Cochenour then approached Alex Mackenzie and associates, and the present Company, Cochenour Willans Gold Mines, Limited, was organized on April 9th, 1936, and sufficient money was raised to continue operations. Under the direction of W. P. Mackle, the shaft was deepened and a second level was established at the 275-foot horizon; but, due to several adverse reports by outside engineers, it was found impossible to raise sufficient money to carry on the work and operations were suspended in December, 1937. In January, 1939, an agreement was entered into with Gold Eagle Gold Mines for the milling in their plant of some Cochenour ore. A total of 4,959 tons was treated, and the results were so encouraging that further finances were raised by C. A. Gentles & Company, of Toronto. Following further development in the mine, it was decided to erect a mill. Construction was started on September 1st and the mill was turned over on November 29th. The first gold brick was poured on December 23rd.

Jan 1, 1942

By Sengpasith Houngaloune

Arsenic, which is a toxic and carcinogenic element, causes serious environmental problems throughout the world. It is also known as a major contaminant in the non-ferrous mining and extractive metallurgical industries, thus its disposal is one of the most important environmental issues for the mining and metallurgical industries. In order to ensure a safe disposal environment for the final wastes, stabilization of arsenic has been studied extensively with various approaches. Solidification/stabilization (S/S) represents one of the most effective methods to reduce the availability of arsenic in soil and waste by transforming toxic or potentially hazardous phases into less hazardous ones. Cement based S/S processes could reduce the solubility of arsenic in solid waste, using inorganic binders such as cement, lime, and pozzolanic materials. A new tailings management technique, called cemented paste backfill (CPB), has become widely employed for improving mining techniques and for tailing storage purpose and this technique could also enhance arsenic stabilization, by fixing the contaminants in the binder matrix. Disposal of arsenic in the form of scorodite (FeAsO4?2H2O) has been widely accepted as currently the most suitable method for stabilization and the safest known storage material. The Bio-scorodite process has been reported to be more economic and environmentally friendly method than the chemical crystallization processes. Retention of arsenic by schwertmannite (Fe8O8(OH)6SO4), a metastable ferric oxyhydroxy sulfate mineral, has gained more attention in the recent years. Schwertmannite has a large specific surface area and high capacity to adsorb arsenic in solution. Several researchers have reported that the transformation of schwertmannite to goethite could be retarded by the presence of adsorbed arsenic; therefore schwertmannite might be viable alternative for long-term storage of arsenic. In this paper, various approaches used in arsenic stabilization are reviewed with emphasis on the development in the recent years.

Aug 1, 2013

By Pavel Vasak

Microseismic monitoring has become standard practice in the mining industry as a ground control monitoring tool at depth. Translating the information into practical hazard assessment tools for the rock mechanics practitioner is the focus of research jointly conducted at Creighton Mine by INCO Mines Technology Centre (MTC) and the Geomechanics Research Centre (GRC) in Sudbury, Ontario. Rock mass damage mechanisms are typically related to stress and the presence of geological structures. Due to well executed de-stress blasting practices at the mine, stress related problems are minimized. However, structurally related damage mechanisms associated with shear zones, faults and joints pose a substantial hazard. Identifying active structures from the dataset of seismic and microseismic events is generally problematic. We propose a new methodology that uses a combination of spacetime event density, hierarchical clustering and principal component analysis to identify planes of microseismic activity, termed active planes (APs). Once identified, the presence and intersection of active planes can be used to provide a hazard ranking for nearby excavations. The ranking is based on the standard Q rock mass classification system, with emphasis on the joint set number (Jn) and stress reduction factor (SRF) parameters. If the rock is treated as a fractured continuum, then, the Jn indicates the degree of freedom for blocks to move and hence, increased potential hazard. An increased hazard can also result if the APs are larger-scale and discrete (faults) rather than ubiquitous (joints). In this case the SRF is used as a measure of the degree of looseness in the rock mass.

May 1, 2004

By Jan E. Nesset, Phillip J. Mackey

"Studies have shown that there is a correlation between commissioning and start-up time, i.e. time to reach full plant design capacity, and the degree of innovation and technical/engineering uncertainty in the project design. The paper describes the types of start-up curves for plants according to the level of technology or uncertainty in the process design. The need to properly describe and understand the commissioning and start-up time is examined using these curves and the importance on project success is highlighted. A number of case histories of recent mining and metallurgical projects are also reviewed. Finally, the paper reviews how to better assess the level of start-up uncertainty associated with a project and makes suggestions for decreasing the commissioning time due to technological risk.INTRODUCTIOThe start-up of a new mining and metallurgical facility, a much anticipated event, is a critical step in the life of such a project. Achieving a successful start-up and reaching the design capacity on-time requires careful planning, a thorough understanding of the key technological and engineering components involved and a well-trained and adequatelystaffed start-up crew. In this paper, some of the aspects related to start-up of a mining/metallurgical project will be explored, and in particular, the impact of the technology component will be examined. In order to illustrate this, a number of case histories based on recent mining and metallurgical projects will be discussed. Ways of assessing and understanding the uncertainty associated with technological issues related to start-up of a mining and metallurgical plant will also be examined.The history on mining and metallurgy is full of success stories of great mines and mills that are now considered “company makers” (well known examples of such successes include the Horne mine for Noranda which had a 1 year start-up in 1926-27, the Dome mine for Placer Dome, the Grasberg deposit for FMI in Indonesia). Less well documented are specific studies relating to plant start-ups and what constitutes a success or a failure, however there are a few notable references in the literature and these will be reviewed."

Jan 1, 2003

By Andre L. De Vegt, Cees J. N. Buisman

"For the past eight years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps:1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (H2S). The H2S reacts with the dissolved metals to form insoluble metal sulfide precipitates.2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur.Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m3/d. A test program, utilizing a large scale pilot plant, will commence in November 1995 at a copper mine in the U.S.A. to remediate groundwater contaminated with sulfate and heavy metals. Biological reactor performance and selective metal recovery will be studied. Sulfur dioxide (S02) can be removed from fluegas using a combination of scrubber technology and the two biological steps. The end product is elemental sulfur. A commercial size biological desulfurization plant has been in operation since July 1994 treating 50,000 Nm3/h of fluegas. Sulfide can be removed from mining waters or anaerobic wetlands using a THIOPAQ® Sulfide Oxidizing reactor.lntroductionSulfur can be present in various water and gaseous streams in a mining operation. In many cases the sulfur compounds have to be removed because of toxicity, corrosive properties and contribution to acid rain. Mine waters can contain dissolved heavy metals. An efficient way to remove dissolved metals removal is the precipitation as metal sulfides. Paques has developed and installed treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. These treatment systems biologically convert sulfate to hydrogen sulfide (H2S) which can be used in heavy metal precipitation. Excess H2S is biologically converted to elemental sulfur. This paper provides an overview of these newly developed biotechnological treatment systems."

Jan 1, 1997

By Khosrow Ebrahimi

We document the occurrence, mineralogy and firing properties of magnesite from hydrothermal deposits in the upper Cretaceous ophiolites of Eastern Iran. These deposits occur as thin veins of nearly pure cryptocrystalline magnesite with only trace amounts of quartz, calcite, and dolomite. Ratios of CaO/SiO2 in the bulk ore are variable. The composition of dead-burned magnesite from these deposits, calcined at different temperatures and durations, is predictable from phase equilibria. Textures of the calcined magnesite were studied by SEM; results show that the principal impurites produced during calcination are forsterite, monticellite, merwinite, dicalcium and tricalcium silicates, and that these are located principally at triple junctions of the periclase crystals. The size of periclase crystals increased with temperature and duration of calcination and the amount of periclase-periclase grain contacts was reduced by increasing the concentration of impurities in the starting products. EPMA show: 1) that CaO and FeO contents in periclase increase steadily with an increase in the CaO/SiO2 ratio and the FeO content of the bulk ore, respectively, and 2) that limited solid solution exists between impurites. This study demonstrates that high quality dead-burned magnesia refractories can be produced from the Iranian magnesite with low CaO, SiO2 and FeO contents.

May 1, 2004

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By Colin Hardie, Simon Pelletier, Rakan Rhabani, Guy Comeau

"In order to improve the nickel concentrate thickener operation at Raglan Mine, two pulp deaeration cyclones were installed. These units obtained from Outotec Pty Ltd, also called the FrothBuster®, have been in continuous operation since mid-October 2006. The primary objective of the de-aeration cyclones is to lower the solids content in the thickener overflow by de-aerating the concentrate pulp before it enters the concentrate thickener. This dearated slurry should help decrease the nickel particle losses that report to the thickener overflow because of the flotation effect within the thickener.Optimizing the de-aeration cyclones has been a slow and ongoing process, however, initial testing is encouraging. The latest test results indicate a 50 % reduction (0.070 to 0.035 % solids) in nickel losses to the concentrate thickener overflow resulting in an additional $350,000 in annual revenues.This paper will present an overview of installing the de-aeration cyclones within a limited space, as well as the preliminary commissioning and testing challenges. This paper will also discuss the most recent concentrate thickener operating results since the de-aeration units were installed.INTRODUCTIONThe Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik Region has been in production since 1997. In early 2002, the concentrator implemented the Zero Process Water Discharge (ZPWD) project to recycle the process water to decrease fresh water consumption and reduce discharges to the environment. Due to this initiative, the chemistry of the process water changed significantly resulting in flotation concentrate streams, which were very frothy and difficult to manage. This phenomenon has resulted in operational challenges in many areas of the concentrator including slurry pumping, flow measurement and concentrate thickening.In October 2005, the Raglan Mine underwent a conversion from an AG mill to a SAG mill operation in order to increase throughput and to optimize key process areas. As part of this project, the first two North American pulp de-aeration (FrothBuster®) units from Outotec were installed to improve the operation of the concentrate thickener. The primary objective of the deaeration technology was to lower the solids content in the thickener overflow by de-aerating the concentrate thickener feed pulp. This in turn was to reduce the froth, which accumulates on the thickener surface, and more importantly reduce valuable nickel losses to the thickener overflow because of the flotation effect within the thickener."

Jan 1, 2008

By Véronique Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modeling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioniong of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

May 1, 2003

By D. M. Wyslouzil

"Micron or sub-micron size gold inclusions in sulphide minerals cannot be extracted by conventional cyanidation. The gold surfaces must first be exposed by decomposition of the sulphides. As an alternative to roasting, pressure oxidation was found to be a most satisfactory method to decompose the sulphides and expose the gold particles. For cyanidation the pressure oxidation pulp has to be neutralized and stabilized with lime. It was found that thiourea can extract the gold directly from the pressure oxidation pulp without pH adjustment and oxidant addition. The main obstacles against the common use of thiourea are circumvented by a recently described control method of the emf during leaching.INTRODUCTION Amalgamation and cyanidation are the most conventional processes for gold extraction. The prerequisite for gold extraction is the possibility of gold surface to be contacted by mercury or by the cyanide solution. Encapsulated gold has little chance of contact and this leads to poor extractions.The reasons why a gold ore may be refractory are: micron or sub-micron size gold particles included in the sulphide minerals, such as pyrite and arsenopyrite; presence of and association with antimony, arsenic, tellurium and carbonaceous minerals. Some alternative processes, such as double oxidation(1,2), pretreatment with lime , H202, chlorine and Caro's acid, roasting and thiourea leach, have solved some of the problems of ""refractory"", but the sub-micron gold in sulphide minerals still shows little response. Roasting and the cyanidation of the calcine was one of the most successful approaches for this type of gold ore.There are two disadvantages to the roasting process: (1) the generation of sulphur, arsenic, antimony and mercury containing gases is undesirable and the control is extremely expensive; (2) gold particles might be fused in the roasted product and the oxidized base metals in the calcine might reduce the cyanidation efficiency. In recent years the pressure oxidation process has been considered as one of the more effective and satisfactory methods to decompose the sulphide minerals and expose the gold surface to the cyanide leach solution. The pollution problem could be better controlled and the gold extraction is more amenable."

Jan 1, 1985

By Janis A. Shandro

The mining sector is a major economic driver for Canadian, and British Columbian communities. In parallel strong commitments have been made by industry to the well-being and sustainability of associated communities. However, these dimensions are the least understood. Especially lacking are focused regional investigations that compare the well-being and sustainability of communities dependent on different resources sectors. It is hypothesized that this type of comparative analysis will help to foster a greater understanding of what makes a resource or mining community healthy and sustainable. This paper describes research that examined community-level indicators associated with well-being (e.g. education, income and employment) and sustainability (e.g. economic diversity). The indicators were derived from Canadian Census data for 31 British Columbia resource-based communities (with a focus on mining) during a period of time (1991 to 2001) when resource sectors experienced an economic downturn. Our findings identify that during this decade, mining communities differed significantly from other resource-based communities, and comparative analysis of census derived indictors illuminate challenges that mining communities in British Columbia face with respect to wellbeing and sustainability (such as economic diversity, unemployment, and population loss). To contribute to the mining sector?s efforts towards meeting their commitments to communities, this paper concludes by proposing strategic opportunities aimed at the enhancement of mining community sustainability for policy-makers, communities, and the mining industry to consider.

May 1, 2011

A rough simulated borehole has been developed for the installation and dynamic testing of rock bolts a the WASM Dynamic Test Facility. The rough simulated borehole is used for rock bolts that are sensitive to equipment installation technique or borehole geometry (particularly friction rock stabilisers and resin encapsulated bolts). An extensive axial test program has quantified a difference between the static and dynamic capacity (kN/m of embedment) for friction rock stabilisers once sliding starts. The 47mm split tube bolt has a 50% reduction in embedment capacity (but with significant variation) dissipating 2.7kJ/100mm of sliding per meter of embedment, and the Omega (inflatable) bolt had a 70% reduction in embedment capacity dissipating 6.2kJ/100mm of sliding per meter of embedment. The Omega bolt dynamic capacity remainder at least equivalent to the split tube bolt static capacity.

May 1, 2009

By G. Couture, J. -F. Dubé, F. Letarte-Lavoie

"The Xstrata Nickel Raglan concentrator, located in Quebec’s Nunavik region, has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high-grade nickel ore, the plant’s current capacity is 1.3 million tonnes per year due to various optimization projects. In 2011 and 2012, the Metallurgical group, with assistance from BBA, updated and optimized the variables affecting SAG throughput in order to optimize process stability while maintaining maximum plant throughput. This project consisted of reviewing the control strategy and completely updating the pre-existing Fuzzy Logic controller. This paper describes the successful update of the controller including a complete revision of control rules, a new process control strategy and the integration of new process variables, most notably mill rotational speed. It will also show how this new approach has provided a simple and robust way of delivering both an increase in throughput while reducing process variability.INTRODUCTIONThe Xstrata Nickel Raglan Mine concentrator is located in Northern Quebec along the 62th parallel. It has been in operation since 1997 and was originally designed to treat 800,000 tonnes of ore annually. The Raglan Agreement held with the Makivik Corporation and the Inuit communities limits the annual tonnage of ore that can be processed at 1.32 million tonnes.The ore is processed in a 24 foot variable speed, semi-autogenous grinding mill (SAG). The conversion from Autogenous Grinding (AG) to SAG was completed in 2006. Before the ore is processed by the SAG, its size is analyzed by a Wipfrag camera that provides a granulometry estimate. A cone crusher reduces the SAG’s discharge screen’s oversize material. A 14 foot diameter ball mill ensures final grinding before the flotation stage.Many control strategies were used at the SAG over the past few years. Fuzzy Logic was first used in 2007 in order to control tonnage feed to the SAG. This first version only measured the value of the variables without taking into account their rate of change. Revisions were made over the course of the last few years to improve controller performance. Other variables were added such as slurry density and crusher Closed Side Setting (CSS). The previous revision of the Fuzzy Logic was done in 2009 with a review of the rules only."

Jan 1, 2013