Search Documents

By U. Storck

"Shaft sinking for exploitation of the deep potash beds in Saskatchewan involved great difficulties from the very first because of the need to exclude from the shaft the high-pressure water encountered in the overburden. Control of the troublesome Blairmore quicksands was achieved relatively quickly by use of the freezing method and by lining with cast iron tubbing. The unsolved problem remained, however, of sealing the water-bearing Devonian where the formations had extremely low permeability and were thus hard to grout. Long experience in German potash mines had shown that the permanency of the whole mine would be seriously endangered if large amounts of unsaturated salt water were allowed to flow in from the shaft wall and merely removed by pumping. The prevention of water movement and the resulting dissolution of salt in the overburden were known to be most important. In the Alwinsal shaft, water flow from the Devonian has been prevented by the use of a steel and concrete sandwich lining similar in principle to a kind of lining introduced a few years earlier, and for another reason, in German coal shafts. As its installation is neither more expensive nor more time consuming than that of cast iron tubbing lining, this same lining was also chosen as protection against the Blairmore quicksands. The great advantage of the steel lining, in addition to its relatively high strength, is the fact that it is possible to make the joints of the individual segments absolutely and permanently water-tight by means of tested welds. The virtual dryness of the Alwinsal shaft will also result in lower costs because significant corrosion of all its steel installations, including skips, cage and ropes, will be prevented."

Jan 1, 1968

By V. Maazallahi, A. Rouleau, A. Saeidi

"The geometry of the terrain topography before and after the failure are the essential factors for analyzing a landslide and for the design of remedial works. This paper presents a method to determine these factors, considering that the determination of the slide surface profile is difficult and costly using traditional methods and the pre-slide topography data is often not available. The presented method to locate the 3-dimensional geometry of the slide surface is based upon determining the slide surface in 2- dimensional vertical sections. This method utilizes post-slide topography of the area to determine the pre-slide topography and uses equations to estimate the pre-slide situation using a statistical process applied to points located on the sliding mass. This method is tested on the Maskun landslide in Iran. The results indicate the applicability of the proposed method to obtain the key factors for the back analysis of a landslide in a cost effective manner.INTRODUCTIONProbably the most reliable method of determining the strength of soil and rock mass is to back analyze a failed or failing slope (Caia et al. 2007; Wyllie & Mah, 2004). This method is used in geotechnics for estimating geotechnical parameters of the rock and soil mass (Sakurai et al., 2003; Frayssines and Hantz, 2009; Cepuritis et al. 2010), but it requires that the failure mode is well established and that there is complete and precise information available on the slide surface and the sliding mass (Sjöberg, 1996). Measurement of the slope profile before failure provides the basic information required for a back analysis (Hock & Bray, 1981). The post-slide topography is another key factor. The back analysis process for determining the actual strength parameters of soil or a decomposed rock mass after a landslide requires knowledge of the sliding mass geometry, both before and after the sliding event. Many studies are reported in the literature about the application of back analysis for determining geotechnical and geomechanical parameters of rock and soil mass (Sakurai et al., 2003; Cepuritis et al. 2010; Frayssines and Hantz, 2009, Hussain and Stark, 2011), but they generally present little information about the geometry of the slide surface, and the weight of rock and soil mass that slid, although these factors are the most important parameters for back analysis process. Liang and Xue-song (2012) determined the slip surface having the minimum factor of safety (called critical slip surface in deterministic analysis of slopes) and the slip surface with the minimum reliability index (called critical reliability slip surface), but they have not considered the actual profile and geometry of the slide surface. Rocscience (2013) proposes the back analysis option in the Slide software for slope stability study, but it requires an imposed slide surface as input; alternatively, one can estimate by a finite element analysis the surface with the minimum factor of safety. However, this estimated surface is very likely different from the actual sliding surface, considering the uncertainties in input data of the finite element method."

Jan 1, 2015

In most instances, the preferred mining methods in steeply dipping narrow vein deposits are selective methods such as cut and fill or shrinkage. The main advantage of these methods lies in the higher degree of control over dilution that can be achieved. However, where ore body geometry lends itself to it, high yield bulk methods can also be attractive. Higher productivity (and the associated lower costs) and lower worker exposure are some of the significant advantages that have made such methods so popular. The Lapa gold mine located in North-Western Quebec uses the long hole mining method (with cemented rock fill) very successfully despite challenging ground conditions. This paper focuses on the experience of the mine with regards to drilling and blasting practices. Firstly, the reasons that prompted the selection of this mining method at Lapa are examined. Secondly, the challenges that the difficult ground conditions found at Lapa pose to drilling and blasting are discussed. Finally, the results of trials of different drilling and blasting strategies that were performed at the mine are presented with particular emphasis on the lessons learned.

Aug 1, 2013

By J. Lee

As the usage of BIM increased in the construction industry, some construction owners started exploring the use of BIM for maintaining their facilities. Construction Operations Building Information Exchange (COBIE), a spreadsheet data format suggested in 2007 to manipulate building information, is considered as one of the solutions that would facilitate the process of transferring information from BIM to applications for facilities management. Several BIM and Computer Aided Facilities Management (CAFM) applications offer functions to export or import the COBIE data. To facilitate the process of generating the COBIE data out of Building Information Model, some add-in applications, such as COBIE Toolkit for Revit, also were developed. However, most of these applications handle a limited amount of COBIE data. Professionals using these add-in applications therefore sometimes end up spending a significant amount of time to add additional data manually to the COBIE data file. To automatically get a data-rich COBIE file, we developed a prototype application that extracts information from Revit, which is one of the BIM authoring tools, stores them in an external database, and then produces the COBIE file using information stored in the database. We applied our application to a pilot project and produced 8 COBIE worksheets automatically, which demonstrated a significant amount of time saving. This paper presents how our prototype application produces 8 COBIE data sets automatically. It also addresses our attempt to handle more COBIE data sets.

Aug 1, 2013

By Staff

One hundred thousand miles of flying over the North country without a single air casualty; much of it over virgin territory probably never before visited by white men; some of it over regions that abound with possibilities for minerals; all of it effective, for exploration and the establishment of bases and supply-stations, and for the carrying of men and their tools and provisions- this, briefly, is the record of Northern Aerial Minerals Exploration, Limited, a Canadian company organized Jess than nine months ago, which has been functioning, without interruption, during spring, summer, and now into winter. Our planes have ranged from the Alaskan boundary on the west to the Labrador coast on the east, and from the Transcontinental railway north to the Arctic circle. Our prospectors, carried on trips of hundreds, and occasionally thousands, of miles, have gone over large sections of country which were never before explored, and at the end of the prospecting season the Company finds itself in possession of several groups of important gold claims, which look most promising. In addition to this, we have been in contact with deposits of almost every known mineral.

Jan 1, 1929

By C. W. Hancher, B. D. Patton, W. W. Pitt

"There are a number of nitrate-containing wastewater sources, as concentrated as 30 wt % NO3 and as large as 2000 m3/day, in the nuclear fuel cycle. The biological reduction of nitrate in waste water to gaseous nitrogen, accompanied by the oxidation of a nutrient carbon source to gaseous carbon dioxide, is an ecologically sound and cost-effective method of nitrate waste disposal. These nitrate-containing wastewater sources can be successfully biologically denitrified to meet discharge standards in the range of 10 to 20 g N(NO3-)/m3 by the use of a fluidized bed bioreactor. The denitrification bacteria are a mixed culture derived from garden soil; the major strain is Pseudomonas. In the fluidized-bed bioreactor, the bacteria are allowed to attach to 0.25- to 0.50-mm-diam. coal fluidization particles, which are then fluidized by the upward flow of influent wastewater. Maintaining the bacteria-to-coal weight ratio at approximately 1:10 results in a bioreactor bacteria loading of greater than 20,000 g/m3,This paper describes the results of a bio denitrification R&D program based on the use of fluidized bioreactors capable of operating at nitrate levels of up to 7000 g/m3 and achieving denitrification rates as high as 80 g N(N03-) per day per litre of empty bioreactor volume. IntroductionThe discharge of wastewater containing nitrate at concentrations greater than stipulated by the Environmental Protection Agency (EPA) creates an environmental hazard and constitutes a civil and/ or criminal legal liability.(I.2) At present, we have three options: (1) recycle and reuse of nitrate streams the total economic and technical balance should be Closely examined; (2) use of an alternative acid, which may pose an entirely different set of problems ; or (3) disposal of nonreusable nitrate sources by an environmentally acceptable procedure."

Jan 1, 1980

By K. Soldenhoff, M. Fainerman-Melnikova

The use of strong base resins for uranium recovery is severely affected by the presence of chloride ions in solution. In areas where high-quality process water is not readily available, the use of saline water would extend the potential application for ion exchange in uranium processing. This study presents measurements of uranium uptake, using a wide range of commercially available weak base anionic exchangers, from solutions with chloride concentrations ranging from 2.5 to 22 g/L Cl. Out of 14 weak base anionic resins tested, 3 were identified that were not severely impacted by the presence of chloride and significantly outperformed a gel strong base resin typically used for uranium recovery in high-chloride environments. The uranium loading was sufficiently high for the consideration of development of the application of uranium recovery from uranium ores leached with seawater.

Jan 1, 2012

By Peter Hood

Data on world-wide geophysical activity in mining exploration programs are collected annually by the Society of Exploration Geophysicists' Geo-physical Activity Committee as part of a continuing service to the industry. The data are obtained by sending out questionnaires to all organizations which are known to be carrying out mining geophysical work; the organizations canvassed include mining companies, contractors, government departments and universities. The questionnaire is divided into three sections; namely, ground methods, airborne methods and research. The data compiled from the questionnaires show that world-wide utilization of mining geophysical methods reached a new high in 1967 with total expenditures of (U .S.) $32,323,240. This was divided as follows: ground methods, $18,106,785; airborne methods, $10,-123,405; and research, $4,093,050. For the ground methods, most money was spent on the induced polarization technique ($5,681,780); electromagne-tic methods were second in reported expenditures ($2,010,900). The total reported geophysical line mileage flown was 1,275,072 line miles, with aeromagnetic surveying being the most popular airborne method. The total amount spent on aeromagnetic surveys was $5,832,564 for 895,420 line miles. This gives an average cost of (U.S.)$6.50 per line mile.

Jan 1, 1968

By Pavel Vasak

Microseismic monitoring is becoming standard practice in the Canadian mining industry, particularly as mines get deeper. Full-waveform microseismic systems allow the operator to distinguish the event source mechanism, e.g., blast, shear slip or stress-induced fracture. At mine sites that heave a microseismic system operator blasts are manually identified by comparing the event waveform traces to the morning blast logs. However, this procedure is not routinely done at sites where a system operator is not present and this can lead to misinterpretation of the data at a later stage, particularly where the interpretation is outsourced, often many years later. It is critical to improve the microseismic data quality and consistency for processing and interpretation with a reliable technique to filter out blasts and blast related seismicity. This paper presents the development and implementation of a simple blast identification and filtering routine. The routine was developed specifically for Vale?s Creighton Mine about a decade ago, but is made sufficiently general so that it can be used at any mine site with an ESG (Engineering Seismology Group Canada) based full-waveform microseismic systems. The routine is strictly a post-processing procedure developed for use with the Access database data structure used by ESG. The algorithm was tested at Creighton Mine and a success rate of 80 to 90% was achieved, when compared to manual blast picks.

Oct 1, 2010

By P. M. Dranchuk

"""PLANET EARTH seen from space appears as a fragile and limited life-supporting system in a vast emptiness. That such a view is, in fact, an accurate one is now more widely accepted than it was not long ago, before Earth's problems of over-population, overconsumption, limited resources and environmental degradation attained the limelight. The danger is that a government and public now deluged by doomsday prophecies and bemused by equally confident reiterations that technology will cure all may hesitate in coming to grips with the problem, in the hope that, given time, it will go away."" With these words, Preston Cloud begins a recent editorial, in Science(l), in which he presents a brief resume of some of the findings of the Committee on Resources and Man of the National Academy of Science-National Research Council(20.Their report, which is based on a two-year study by an extremely competent group and consists of some 250 pages of text, is even more far-reaching and sobering than the report on Energy Resources(3). It begins by quoting Sir Macfarlane Burnet as follows:""There are three imperatives: to reduce war to a minimum; to stabilize human population, and to pre-vent the progressive destruction of the earth's irreplaceable resources.(4)"

Jan 1, 1971

By G. R. Heffernan

"IntroductionTHE PURPOSE of this paper is to give a •brief history of iron and steel in British Columbia, a quick look at the present operations of Western Canada Steel, Limited, a review of iron ore resources and iron and steel markets, and a projection of what the future might hold for the industry in British Columbia.From the Past to the PresentWhile the paper is entitled Past, Present, and Future, in covering the past, which we shall call the time prior to 1947, there is very little to be said. Small shipments of iron ore were made from the Texada deposits by the Puget Sound Iron Company from 1886 to 1907. Total ore shipped did not exceed 70,000 tons. Part of this is believed to have been used in building a United States battleship in 1907 in the Bremerton Naval Yards in Seattle, Washington.In 1914 a small steel mill was started on Lulu island, rolling bars from •box piles and used shafting. This mill operated spasmodically for a few years but finally burned down in 1921. The rolling mill stands were sold to China and are no doubt in operation in China today.In 1916 the City of Port Moody assisted in the financing of a mill which operated on re-roll rails, box piles, and steel ingots made in an experimental electric furnace in Port Moody. This furnace also produced small quantities of pig iron scrap. The backers of the Port Moody mill showed a great deal of enterprise and must have been a very forward looking group, since this was one of the first recorded applications of the electric furnace to small ingot production. Despite their enterprise, the operation was unsuccessful and terminated in 1921."

Jan 1, 1953

By C. H. Knight

"THE OBSERVATIONS that follow are confined to simple wet cyclones such as the cylindro-conical unit developed by the Dutch States Mines and marketed in America under the trademark 'Dorr-Clone'. Energy to do the work comes from the inlet velocity of the feed slurry, which is usually pumped' to the unit by a centrifugal pump.Such cyclones are simply classifiers of enormous capacity and depend for their separating effect on differences in rates of particle settlement. These particle settling rates, of course, vary with particle size, particle density, particle shape, pulp viscosity, and pulp density.The dilution of the overflow product affects both pulp viscosity and pulp density. In most operations, the temperature and the composition of the liquid -hence its viscosity --are fixed, but both pulp viscosity and pulp density can be changed by changing pulp dilution.Since the separating effect depends on differences in rates of particle setting, a perfect split with 100 per cent of the particles coarser than a given size in the underflow and 100 per cent of the finer sizes in the overflow is not possible. Just how far the separation departs from this perfection can be calculated rather exactly from the following principles, which also apply to mechanical classifiers. In removing or settling out of the overflow product all particles up to a specified size, some of the finer particles must settle out simultaneously."

Jan 1, 1955

By R. A. Wyman, F. E. Hanes

THE demand for high-quality aggregate is increasing in all phases of the construction industry and in all organizations associated with road building in Canada. The production of aggregate in Canada has increased almost continuously since the end of the war and has quadrupled since 1948. Increases during the past fifteen years can be accounted for by the expansion in all types of construction, particularly that of roads and highways. Total construction in 1959, based on preliminary estimates, has been valued at $7 billion, and an increase fore-cast for 1960 indicates optimism on the •construction horizon (1). Cement produced in Canada in 1959 amounted to 6.3 million tons. This is more than 2.5 times the 1948 production. Increased cement production indicates an increased use of concrete, and thus an increased need for aggregate. Natural sand and gravel deposits are gradually being depleted.

Jan 1, 1962

By C. Doyle, J. Brennan, C. Díaz, J. Hrepic, K. Cushnie

"In 1991/1992, INCO undertook a successful R&D program aimed at extending the lining lives of the top blown rotary converters (TBRCs)at its Copper Cliff Nickel Refinery (CCNR) and the electric furnace at INMETCO. At the laboratory scale, this effort was divided into three phases. In the first part, mineralogical work was performed on six refractories that were either currently being used to line these vessels or were considered suitable alternatives. In the second part, this mineralogical knowledge was used to help determine the compositions of slags that would not corrode the bricks at the operating temperature (1600°C) of the above furnaces. Finally, several important properties of the six refractories were measured to complete their evaluation as candidate linings. This paper reports the results of all three phases of the laboratory scale R&D work.The mineralogical work showed that rebonded fused grain magnesite-chrome (RFG-MC) bricks consist principally of periclase with minor amounts of free chromite and trace quantities of silicates monticellite and sometimes olivine. The bricks are principally held together by periclase-periclase direct bonding. Of note, the bulk of the chromite exists as exsolved precipitated blebs within the periclase grains. These likely redissolve at high temperature.Slags on the periclase liquidus coexist stably with these refractories. Examples are presented using CaO-MgO-Al2O3-SiO2 slags at~1600°C.Finally, the two refractories manufactured using close to 100% fused grain material generally outperformed the others in terms of physical properties and certainly were superior in their resistance to slag penetration damage."

Jan 1, 1997

By G. D. Garland

The influence of natural electric currents, induced in the earth by changes in the earth's magnetic field, on the electric logging of boreholes has not always been recognized. Measurements made with fixed electrodes of changes in the vertical potential gradient in a hole near Calmar, Alberta, have indicated the effect of earth currents related to magnetic disturbances. It is found that appreciable errors in self-potential logging could arise during periods of magnetic storms, but the precise pat-tern of disturbance in any area seems to depend on the local structural conditions. As the amplitude of the natural earth currents increases toward the auroral zone, it is suggested that periods of magnetic disturbance be avoided, if possible, when electric logs are taken in the northern part of the western sedimentary basin. NATURAL electrical currents flow continuously near the surface of the earth, apparently as a result of electromagnetic induction

Jan 1, 1962

By Howard W. Tipper, Richard B. Campbell

"The Quesnel Trough is underlain by a thick sequence of mainly Upper Triassic and Lower Jurassic volcanic-clastic and sedimentary rocks that lie between the highly deformed Proterozoic and Paleozoic rocks in the Omineca Geanticline to the east and the Upper Paleozoic Cache Creek Group in the Pinchi Geanticline to the west. Broad areas of the Trough between Kamloops and Williams Lake are covered by Eocene volcanics and sediments and by Miocene-Pliocene plateau lava. Granitic intrusions were apparently mainly confined to two major episodes; one about 200 m.y. ago (coeval with the Guichon batholith) and one about 100 m.y. ago. In addition, the region includes small granitic and syenitic intrusions, some porphyritic, that may be all or partly still younger. Exposures in the region are generally small and scattered, obscured by widespread, not necessarily thick glacial deposits. This, together with the extensive Tertiary cover, makes prospecting difficult. The part of the Quesnel Trough discussed here is the direct northwest-ward extension of the copper-rich Kamloops-Merritt-Princeton region. It contains the Boss Mountain molybdenum mine, related to a breccia zone induced in a batholith of the oldest group by a younger intrusion, and the Cariboo Bell copper deposit in Lower Jurassic volcanic-elastic rocks and syenitic intrusions. The Gibraltar deposit, in a 200-m.y. intrusion, is within the Pinchi Geanticline close to the margin of the Trough. Molybdenum prospects are mainly restricted within or near the 100-m.y. granitic rocks. Copper prospects, on the other hand, are most prominent in the volcanic-elastic rocks and in the 200-m.y.-old granitic rocks, although they can also be spatially related to younger intrusions. Copper thus has a wide potential distribution.The writers believe that the region is deserving of careful and comprehensive exploration by directly applying the knowledge and techniques developed in the important producing areas to the south. All of the major pre-Tertiary geological elements seem to have potential for mineral deposits; none should be ignored. A thorough knowledge of the thickness and distribution of the Tertiary rocks and the development of geophysical methods to ""see through"" them is of particular importance."

Jan 1, 1970

By D. B. Dreisinger, M. R. Tavakoli

"Vanadium has been produced from a variety of sources. This metal is known to make aqueous solutions of complex speciation as a function of vanadium concentration and pH. Considering the method of leaching, the impurities in the pregnant leach solution, and the planned vanadium product, different extractants and flowsheets can be applied for solution purification. This paper reviews the purification of vanadium leaching solution using organophosphorus, solvating, and amine extractants. This review focuses on vanadium separation from iron, molybdenum, and uranium, which are often present in vanadium resources such as primary ores, fly ashes, and spent catalysts.RÉSUMÉ Le vanadium est produit à partir de diverses sources. Ce métal est connu pour permettre des solutions aqueuses de spéciations complexes en fonction de la concentration du vanadium et du pH. En tenant compte de la méthode de lixiviation, des impuretés dans la solution mère de lixiviation et du produit de vanadium planifié, divers agents d’extraction et schémas de traitement peuvent être mis en oeuvre pour purifier la solution. Le présent article étudie la purification de la solution de lixiviation du vanadium au moyen d’extractants organophosphorés, solvants et aminés. L’étude cible la séparation du vanadium du fer, du molybdène et de l’uranium, lesquels sont souvent présents dans les ressources de vanadium telles que les minerais primaires, les cendres volantes et les catalyseurs usés."

Jan 1, 2016

By Dale Verran, Jared Orynik, Chad Sorba, David Bronkhorst

Denison Mines Corp. (“Denison”) has a 90% interest in the Wheeler River Uranium Project (“Wheeler River”) located along the eastern edge of the Athabasca Basin in northern Saskatchewan between the Key Lake mill and the McArthur River uranium mine. The project is host to the high-grade Phoenix and Gryphon uranium deposits, discovered by Denison in 2008 and 2014 respectively, which include combined Indicated Mineral Resources of 132.1 million pounds U3O8 (1,809,000 tonnes at an average grade of 3.3% U3O8). The Pre-Feasibility Study (“PFS”), completed in accordance with NI 43-101 in September 2018, is highlighted by the selection of the In-Situ Recovery (“ISR”) mining method for the development of the Phoenix deposit, with an estimated average operating cost of $4.33 (US$3.33) per pound U3O8. Phoenix is the highest-grade undeveloped uranium deposit known globally, including Indicated Mineral Resources of 166,000 tonnes at 19.1% U3O8 for 70.2 million pounds U3O8. The paper aims to provide a summary of Wheeler River and an overview of the proposed development of the Phoenix and Gryphon deposits according to the PFS completed for the Project. Further details regarding the PFS, including additional scientific and technical information are described in greater detail in the NI 43-101 Technical Report titled "Pre-Feasibility Study for the Wheeler River Uranium Project, Saskatchewan, Canada" dated October 30, 2018 with an effective date of September 24, 2018. A copy of this report is available on Denison's website and under its profile on SEDAR at www.sedar.com and on EDGAR at www.sec.gov/edgar.shtml.

Jan 1, 2020

"IntroductionNOTE.-All figures on the supply and consumption of coal in Canada cited in this paper were collected and reported by the Dominion Bureau of Statistics. The friendly and efficient co-operation of the officials of the Bureau. is the foundation upon which it has been my privilege to rely in the preparation of this and two earlier papers ( 1). My thanks are due also to our own staff on the Dominion Coal Board, who spared neither time nor effort in helping to prepare this paper.STATISTICS are comparatively dull and, to many people, coal statistics are duller than most. Coal is, however, the one basic mineral upon which our whole way of life depends and it may be well if attention is drawn to this fact by an occasional statistical review of the coal position in Canada. The recent furore over the oil and gas discoveries has so obscured the basic position of coal in many minds that a little basic coal information may be useful. It is for this reason that, for the third successive year, a factual survey of the coal position is being presented.In the previous papers (1) explanations have been given of the basic considerations in the preparation of these reports and some special phases of the overall picture have been examined. For these explanations, the earlier papers may be consulted."

Jan 1, 1952

By G. R. Phare

Explosives formulation is dictated by desired field performance, which in turn is dependent on such physical properties as strength, velocity of detonation, sensitivity, and water resistance. The design of explosives to obtain these properties is discussed with some reference to detonation and rock mechanics theory.

Jan 1, 1958