Search Documents

By Solar D. Andrés

Several large open pit mines are facing the challenge to design and plan an underground transition to sustain the long term future of their operations. The desired underground method is Block Cave since its natural high productivity and low operating cost that could compete against the open pit cost to mine the final open pit pushbacks. It has been found at several operations where this transition is taking place that the pit limit at which transition is performed is rather deep. This aims to think that perhaps several transition projects have started late in the life of an operation producing an over stress in the transition project and reducing the flexibility in the design of the overall infrastructure and a substantial lost in the complete project NPV. Traditionally the approach to plan open pit underground transition consists of sequentially deciding the final pit using a Lerchs and Grossman type of optimization to find the overall maximum pit shell and then running block cave simulations to find the best footprint for the underground option. The research summarized in this paper is related to the development of an integer linear programming model that aims to compute simultaneously the maximum NPV of the combined option final limit open pit and block cave underground footprint. The model has been tested using two large block models representing two of the current operations in the process of transiting from open pit to underground operations. Finally, the integrated open pit underground transition model is going to be compared to the traditional sequential approach in order to define which method achieves the best NPV. The paper illustrates both case studies in depth.

Oct 1, 2009

By E. J. Schwarz, A. A. Winir

"Absolute magnetite contents were determined for asbestos specimens in various stages of milling by using a Faraday-type thermomagnetic balance. Comparison of these results with magnetic ratings (MR) supplied by the mining companies cooperating in this study reveals strong scatter. The main cause of this scatter is thought to be that the MR values were obtained in magnetic fields well below the saturating field of magnetite (5,000 oe). However, only the saturation moment is an intrinsic property and consequently must be used for the purpose of obtaining reliable estimates of the magnetite content. Curie points indicate that virtually pure magnetite and possibly Ni3Fe is present in all samples, and another phase, probably (Cr, Al) magnetite, is present in a few samples. The susceptibility in fields stronger than 5,000 oe is positive and falls in the normal paramagnetic range, whereas sy nthetic chrysotile exhibits weak diamagnetism. This suggests that, as a general rule, the least adulterated natural chrysotile concurs with the samples showing the smallest positive susceptibility above 5,000 oe. The magnetite appears to increase in quantity with a decrease in fibre length and to be somewhat more uniform in distribution for samples showing substantial fiberization (opening of the fibres)."

Jan 1, 1971

By Marc C. Bétournay

A number of successful proof-of-concept projects have been carried out to replace conventional power application, such as diesel and rechargeable batteries, in underground mine vehicles. This has led to the development of the world?s first fuelcell production vehicle, a mine locomotive. A mine loader project has also started and several other projects are planned. These projects are providing the mining industry with the required information to make this technology shift possible. The application of fuelcell power will yield several important benefits such as the elimination of underground diesel emissions, significant reduction in the primary extraction?s sector greenhouse gas emissions and support for a more productive scenario. This article reviews these successes, discusses ongoing and potential projects and presents the technology application benefits that could be possible for mining operations.

May 1, 2003

By Brian W. Mackenkzie, Jozef Lajzerowicz

This paper is intended to familiarize planners in the noncommunist world with the district planning approach used in eastern Europe for mining development. It deals generally with the basic nature of the district planning problem, the planning process for mining development and the state organization for the planning of mining districts. A number of applications of district planning techniques to both established and new eastern European mining districts are described.

Jan 1, 1971

By Renato Macciotta

The argillaceous formation known as the Opalinus Clay is host to the Mont Terri Underground Research Laboratory. The URL was developed to investigate the hydrogeological, geochemical and geotechnical properties of the formation. Underground excavations at the site are characterized by non-elastic and time-dependent deformations. Excavations trending perpendicular to the strike of the bedding presented relatively minor deformations, however, tunnels parallel to the strike of the bedding showed much larger non-elastic deformations. This paper presents an analysis of the measured response of a tunnel trending parallel to the strike of the bedding in Opalinus Clay. The measured convergence is compared to tunnel experience in weak rocks to assess the tunnel stability.

Jun 1, 2012

By D. G. Cerigo

"INTRODUCTIONAn interim report covering an uncompleted project on revenue mill optimization was presented at the invitation of Mr. C.S. Stevens, the Secretary of the Canadian Gold Metallurgists. The work described summarizes the preliminary work carried out at the Noranda Research Centre on computer mill optimization and is an attempt to arrive at a model of a circuit using the ""black box"" approach and hence by using economic factors related to concentrate dollar value to maximize revenue. The help and cooperation of Mr. J.D. Wild, Mr. M.J.S. Bennett of Noranda and Dr. A. Bobkowicz of McGill University is gratefully acknowledged.DERIVATION OF MODELHistorical data from the Normetal mill were used for the study. Normetal ore contains chalcopyrite, sphalerite, gold, silver, pyrite and pyrrhotite. For simplicity, data were chosen for days when only two concentrates had been derived, a copper concentrate which also contains the gold and silver, and a zinc concentrate. In these periods when pyrite concentrate was not produced, its circuit was used as an extra zinc scavenger unit. Figure I is a schematic drawing of the circuit and Table I explains the nomenclature.The mill had been operated to obtain a fixed grade of copper and zinc in the copper and zinc concentrates respectively, at the same time insuring acceptable recovery levels. The target grade for the copper and zinc concentrates had been derived by manual calculations based on past experience. The data used were 170 sets of daily mill reports, a sample of which is shown in Table II. The data consist of daily tonnages of feed, concentrates and tailings and their average compositions obtained by taking samples every twenty minutes from each stream and analyzing the daily composite samples."

Jan 1, 1967

By E. Dernedde

Industrial plants located in the province of Quebec, Canada, are subjected to large variations of the ambient air temperature, Building ventilation systems of these plants must have some flexibility in order to meet industrial hygiene standards (TLV for chemical substances, heat stress and cold stress) at any time of the year, The building ventilation of a bath treatment plant of an aluminium smelter in Quebec was examined under summer and winter conditions, Part of the plant has periodic emissions of hydrogen fluoride gas and heat from hot anode butts, CFD modeling was used to optimise the building ventilation of the bath treatment plant, The present study proposes a modified building ventilation system, which improves the internal environment, complies with industrial hygiene standards and also reduces heating costs by 20 % during winter.

Jan 1, 2005

By E. S. Moore

DEEP oxidation and-secondary enrichment of ore deposits, although so important in many parts of the world, are comparatively rare in the Canadian shield. Intensive glaciation during the Pleistocene epoch accounts for their rarity. Glaciation has cost Canada much in the destruction of not only enriched ore deposits, but placers that must have been developed near our numerous gold deposits during the long period of weathering that pre-ceded the Pleistocene. There seems to be a very common misconception regarding the average depth of rock that has been removed from the shield by glaciers. These bodies of ice are usually given credit for the removal of the greater portion of the thousands of feet of rock that we know has been eroded from this large area since Precambrian time. As a matter of fact, the average thickness of solid rock removed can be measured in tens rather than even hundreds of feet, although very deep erosion has resulted in some sections where the glacial ice has been constricted in depressions, such as deep valleys and lake basins. On the other hand, there are few areas within the shield where the glaciers have not disturbed practically all of the mantle rock and some feet of the underlying bed-rock. The chances of finding deeply oxidized cappings and enriched ore deposits are therefore comparatively few and these have been found chiefly where favourable structural and topographic conditions for their formation and preservation have existed. Faulting has been responsible for several of these deposits, and easily decomposed rocks, such as. sulphides and carbonates, have been very important factors. Topographic features, such as high and resistant hills, favourably situated with respect to the ore deposits have, in a few cases, played a part in providing protection from glacial erosion and in furnishing head for the descent of surface waters. At least four cases of oxidation to depths quite abnormal in the Canadian shield have so far been found in Ontario. These are the Helen and Josephine iron mines in the Michipicoten district, the Keeley silver mine in South Lor-rain, and the Ross gold mine in Hislop township, Cochrane district. A deeply oxidized zinc deposit of unusual interest occurs in the Precambrian rocks in New York State, not far from the Canadian border, and there arc the well-known iron deposits in the Lake Superior region of the United States.

Jan 1, 1938

By K. Ogawa, T. Yokoyama

Hydraulic fracturing technique, an applied technique to cause tensile fractures to rock by injecting water pressure to a certain closed section of the borehole, is a measurement method of in-situ rock stress. This technique has the highest track record for techniques used in sub 1000 meter. A feature of this technique is comparatively simple and easy for in-situ stress measurement, because the measurement is applicable when a drilled borehole is available. The predominant advantage of this method is that elastic constants such as Young’s modulus and Poisson’s ratio are not required for determining the value and direction of initial stress. The factors to determine the stress state are the water pressures of re-opening and shut-in of fractures around the borehole wall and its directions. With conventional methods, however, the accuracy of the derived stress states from the observation equations was often adversely affected by the lack of consideration of the remaining water pressure in fractures and insufficient stiffness of the pressurization system. We have developed a new hydraulic fracturing system based on a new test method concept overcoming these defects, and applied to a 300 meter deep borehole in granite. The most important improvement of the new system is an employment of a syringe pump which enables an accurate flow control of fluid with less than 1ml/min in the pressure of 30MPa. Therefore the new test system has a quick response for pressurising in the interval zone, and the measured data was confirmed extremely accurate.

Jan 1, 2015

By Nawshad Haque, Leanne Smith, Hal Aral, Joseph Cho, Warren Bruckard

"Water availability is one of the principal parameters in determining the feasibility of mining projects in arid and semi-arid regions. The volumetric water footprint (VWF) of a conceptual model of a copper flotation plant was found to be 2.45 kL/t Cu ore, compared with an actual measurement reported in the literature of 2.72 kL/t Cu ore. The flowsheet considered included mineral processing stages such as crushing, screening, grinding, classification, separation, flotation, thickening and filtration. The effect of a number of variables on the VWF was evaluated, including solid/liquid ratio, feed mass flowrate, ore loss, water loss, moisture content of ore, ore grade and water recycling. The use of seawater with recycling provided the most environmental and economic advantage among several scenarios evaluated. The study assumed a price of $1/kL freshwater, $4/kL for transport over a 200 km distance at 2,000 m altitude and $4/kL for water treatment. The water related cost of the desalinated seawater use scenario was A$493/t Cu concentrate, while the water related costs of fresh water and blended water scenarios were A$308/t and A$268/t Cu concentrate, respectively. The water related cost (fresh water scenario) accounted for 44% to 49% of the entire mining and processing costs that included drilling, blasting, loading, hauling, crushing, grinding and concentrating. The total overall cost was A$435/t Cu concentrate for the seawater with recycling, compared to A$451/t Cu concentrate for the fresh water with recycling case.INTRODUCTIONReducing the water footprint (WFP) by utilising alternative water sources has been a focus of mining projects due to increasing concerns about water scarcity and growing energy costs. The global mining industry can expect to experience fresh water shortages in the future, and saline or hyper-saline water may be the only available water source to process minerals in arid regions. Extensive studies on alternative water sources (e.g. seawater, desalinated seawater, blended water) and the reuse of process water have recently been conducted (Moreno, Aral, Cuevas, Monardes, Adaro, Norgate & Bruckard, 2011; Aral, Mead, Cuevas, Davey & Bruckard, 2010). Such studies provide sustainable and economic strategies for mines and concentrators in the arid or semi-arid regions of the world such as in Chile, Peru, Indonesia, and Portugal. More work, however, is needed to confirm water consumption data for different base metal flowsheets and use this data to develop water models that can lead to reduced WFPs and more sustainable water usage in the mining industry."

Jan 1, 2016

By Gonzalo Díaz, Diego Mesa, Willy Kracht

"It is well known that frothers affect the amount of water that is transferred to the froth, which has an effect on both the froth stability and the water recovery. On the other hand, since non-selective recovery by entrainment is directly related to water recovery, it can be said that frothers have an indirect effect on flotation selectivity. Recent research on this subject has shown that the non-selective recovery by entrainment, which is characterized by the entrainment factor, is frother dependent. In other words, the entrainment factor is not unique, but depends on frother type.Having different entrainment factors implies that for the same water recovery, the amount of undesired particles reporting to the concentrate may vary if one changes the frother type, which suggests, as a possible explanation, that it is not only the amount of water in the froth what is affected by frother type, but also the froth structure.The purpose of the current work is to study the effect of frother type on foam structure (two phase froth). A quasi-2D cell operated with a slot sparger was used to study the foam structure in the presence of three different frothers: Methyl Isobutyl Carbinol (MIBC), OrePrep®549, and Octanol at the same gas flow rate and reagent dosage. The foam structure was studied using image analysis, and an algorithm based on textural analysis was developed to classify the foams. The results show that it is possible to classify foams according to the frother used, which proves that frothers have an effect on the foam structure.INTRODUCTIONFrothers are usually dosed paying attention to froth stability, condition that is commonly estimated by sight, according to the operator's criteria and experience. This happens because there is not an established procedure or technique for frother characterization, generating qualitative descriptions such as “powerful” or “selective” frothers, which lack of scientific thoroughness and remain under subjective factors. Nevertheless, several works have been done in this line of research. Moyo et al. (2007) classified frothers based on their water-carrying capacity, proving that this characteristic is related with gas holdup and frother type. Previously, Trahar (1981) had related water recovery and gangue particles recovery, defining the entrainment value (ENT). Nowadays it is known that entrainment affects both hydrophilic and hydrophobic because it is not a selective process. In the last decade some studies (for example the one of Konopacka and Drzymala (2010)) delved into different entrainment behaviours dependent mainly on the flotation type (batch or continuous, agitated or columnar, etc.), but there were no studies on the effect of frother type regarding entrainment, since Rahal et al. (2001) argued that the ENT factor was independent of the frother type and concentration, and froth height."

Jan 1, 2016

By Donald O. Downing

"IntroductionThis paper provides an overview of the coal mining industry in Canada with a description of current circumstances. The Canadian industry is placed in a global context and the future prospects of the industry are described. The export market is very important to the future of Canadian coal production and the essential aspects of the market are explained. Future prospects are very much tied to metallurgical coal exports and some key characteristics of that market are discussed, including major technological changes in the industry. Stability in 1996The Canadian coal industry enjoyed another strong year in 1996 continuing a trend established over the last four years. The strength of the industry is based on a stable domestic industry and a relatively healthy inter- national market. The figures bear out these statements. In 1996 total production reached 75 million tonnes and consumption was 52 million tonnes. The major markets for coal in Canada are electricity generating stations (Alberta, Saskatchewan, Manitoba, Ontario, New Brunswick, Nova Scotia) and the steel industry in southern Ontario. Approximately 11 million tonnes of coal were imported and exports reached a new record of 34.5 million tonnes, mainly from western Canada. Canadian Coal FlowsCanada represents a unique case in the coal world because we both import and export coal (Fig. 1). The reason for this apparent dichotomy is Canada’s geography. Eastern Canadian coal markets are located closer to the eastern United States coal fields and are basically served by them. This is true for both thermal and metallurgical coal. Major imported coal users are the steel industry, electricity generators and other industry including the cement industry in southern Ontario, Quebec, New Brunswick, with a little coal imported into Manitoba. Only about 2.2 million tonnes of western Canadian coal move into the east, including both lignite and bituminous coal."

Jan 1, 1997

By Ken G. Kress

Syphons can be a simple, reliable and proven alternative to otherwise more complex pumping systems or low level outlet works. In a simple form they consist of a pipeline constructed over the top of an embankment or high topographic feature, connecting a source pond to a receiving pond or channel (see Photograph 1). The syphon action is initiated by removing air from the pipeline (priming) using simple devices which can be purchased ?off the shelf?. Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate or other devices. Repriming is not required even if the flow is stopped, provided the syphon is not drained. A limiting factor in considering a syphon as a design option is the maximum lift (i.e., vertical distance from source pond level to summit of syphon) which is approximately 9 metres, or less, dependent on syphon pipe features and site conditions. Pipeline syphons can be quickly constructed from readily available materials including steel, polyethylene and PVC pipe. They are particularly well suited to many of the unique conditions often encountered at minesites. This paper identifies situations that can sometimes be best resolved using pipeline syphons. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

May 1, 2001

By J. W. Matousek

"Computer modeling of smelting processes requires internally consistent equations for calculating the compositions of mattes and slags. That is, the sum of the calculated assays must total 100%. One set of equations that satisfies this requirement for copper produced under oxidizing conditions (pSO2>one atmosphere pressure) is given by the following:%[Fe] = 62.0 – 0.775%[Cu]%[S] = 28.0 – 0.00125%[Cu]2%[O] = 10.0 – 0.225%[Cu] + 0.00125 %[Cu]2Mattes containing nickel in appreciable quantities do not have the defined “white metal” end point of approximately 80 percent copper and 20 percent sulphur that is found in the copper system during the converting process. The above equations, however, are readily extended to nickel and nickel/copper mattes for any desired end product composition."

Jan 1, 1996

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018

By Guoxiang Chi

The Cornwallis Fold Belt in the Canadian Arctic Archipelago contains numerous Mississippi Valley-type (MVT) Zn- Pb occurrences and the world-class Polaris deposit. The occurrences are mainly hosted by the dolostone in the Thumb Mountain Formation which spreads over 25000 km2. Success in exploration requires further understanding of the genesis of these occurrences and an assessment of their parentage with the giant Polaris deposit. Syn-sulfide dolomites in regional occurrences share C-O-Sr isotopic characteristics similar with Polaris dolomites, indicating warm basinal brines enriched in 87Sr. The dolomites and sphalerites contain fluid inclusions with ice-melting temperature between ?45° and ?25°C, which is significantly lower than for most MVT districts in the world (?30° and ?10°C). These characteristics indicate that all the Cornwallis occurrences were produced by fluids of the same sources and/or aquifers. The deposit size was largely controlled by the rate and duration of the metal-carrying fluid flow, and by the availability of reduced sulfur at the site of mineralization.

May 1, 2001

By Michael Hopp

The beginning of the electroforming technology dates itself on the beginning of the industrial revolution 1800 to 1820 approximately. Basis was the existence of electricity in order to be able to drive the electro-form-process. With the development of the electroforming, big names of the science-history, like Michael Faraday (1791? 1867), Sir Humphry Davy (1778?1829), Max Schlöter (1878?1946), Werner von Siemens (1816?1892), and many others. Already about 1840, the first monograph originated to electroforming (38). While in the first years the electro-forming most extensive only to the coating of art - or other usefulness-objects was used. At the beginning of the 20th century the formation of objects from pure metals became more and more, later also from alloys to application. One of the first bigger electroforming factory, the ?Württembergische Metallwarenfabrik? was working 1894 in Geislingen / Steige, Germany. In the industrial application, the electroforming-technology is to be imagined away for miscellaneous coatingtasks and the form-body-preparation no longer today (18). A little bit confusing is the german name ?galvano-technology?. It based on the Italian physiologist and naturalist Luigi Galvani (1737 ? 1798). This technically seen is however wrong, right, the name is electroforming. The physical bases were founded mainly by Michael Faraday and Sir Humphry Davy.

Oct 1, 2003

By Barry D. Simmons

"A well-defined approach is essential to ensure the long-term success of a regional exploration program. Teck's approach in eastern Canada is designed to fulfill corporate objectives while recognizing certain unique parameters for exploration in the area. The elements of this approach include clearly defined objectives, technical considerations and personnel policies, all of which are equally important. The goal is a significant discovery before the mid-l990s and the company is confident that this target will be achieved.IntroductionAs one of Canada's oldest continuously operating mining companies, Teck Corporation traces its roots to Kirkland Lake, Ontario, with the development of the Teck-Hughes gold mine in 1913, later supplemented by production from the Lamaque gold mine in Val d'Or, Quebec. Control of the company was acquired by Temagami Mining Company, part of the Keevil Mining Group, in 1959. Credited as one of the first discoveries made using airborne geophysics, the Keevil Group had recently found the small but very high-grade copper deposits at Temagami, Ontario. These developments in eastern Canada formed a foundation for remarkable growth and Teck's present status as one of Canada's most successful and respected mining companies.Teck currently operates successful mining ventures across Canada and has international exposure through its association with Cominco Ltd., M.I.M. Holdings Limited and Metallgesellschaft AG. Operations in eastern Canada, however, remain an important component of Teck's ongoing success. The David Bell and Williams mines at Hernlo, Ontario, are Canada's lowest cost and largest gold operations, respectively. The Niobec Mine at Chicoutimi, Quebec, is North America's only significant producer of niobium. Teck maintains a 45070 interest in Golden Knight Resources Inc., part owner of the successful gold mining operation in the Casa Berardi area of northwestern Quebec. As a significant shareholder in Aur Resources Inc. and as a part owner, Teck is participating in the development of the Louvicourt deposit, a major base metal discovery at Val d'Or, Quebec."

Jan 1, 1992

By S. Mohammadnejad, M. Olizadeh, B. Mehrabi

A new method using a combination of comprehensive mineralogical and analytical approach which includes optical and electrical microscopy and several analytical techniques with diagnostic leaching has been used to characterize the associations and distribution of gold in a variety of minerals from the Zarshuran refractory gold ore, NW Iran. Zarshuran ore with an average of 7.9 g/t Au-grade and about 8% arsenic with gold recovery less than 20% in direct cyanidation is considered as high arsenic, high au-grade refractory gold ore. In most of the refractory ores, gold is associated with arsenopyrite and co-para genetic ore minerals, while in Zarshuran ore; gold is associated with orpiment, realgar and arsenian-pyrite. Considering its mineralogy and As content, it can be considered as the most difficult refractory ore for characterization and processing. Results from the mineralogical examination and diagnostic leaches indicate that there is only a small amount of free gold (17-19%) that is present in cyanide-soluble sulfo-arsenides compounds, predominantly orpiment and realgar. Diagnostic leaches also indicate that little gold is occluded within the silicate structure (14%). Overall, the gold is mostly included in sulfides, arsenic sulfides and sulfo-arsenides (50%). The results also have shown how the technique can be used to gain a good initial understanding of potential metallurgical problems for a refractory gold ore.

Jan 1, 2005

RÉSUMÉ L’estimation la plus précise possible des coûts de minage est d’extrême importance pour les études de préfaisabilité afin de diminuer les risques financiers des projets miniers. Les méthodologies existantes d’évaluation des coûts de minage ne permettent pas de les évaluer avec des marges d’erreur acceptables tout au long de l’évolution des projets miniers. Elles visent à évaluer les coûts unitaires de minage des études préliminaires de faisabilité, pour les principales méthodes d’exploitation, en prenant pour l’hypothèse que ces coûts dépendent principalement du taux d’extraction journalière. Si cette hypothèse peut être justifiée pour l’évaluation du coût d’opération, elle est fort discutable pour l’évaluation des coûts de minage. Pour démontrer que cette hypothèse est inadéquate nous avons analysé la méthode d’exploitation la plus populaire sur le continent nord-américain c’est à dire celle par chambres vides avec retrait horizontal (Hr – Horizontal retreat), ou « Longhole » et celle avec retrait vertical (VCr - Vertical Crater retreat). Il ressort de cette analyse que les coûts unitaires de minage dépendent principalement des conditions géotechniques du massif rocheux et de la largeur du gisement et non pas du taux d’extraction journalière du minerai.

Jan 1, 2010