Search Documents

By D. L. Johnston

"The avenues and degree of participation by aboriginals in the Canadian minerals industry have changed significantly during the thirty years of the author's career in that industry.The typical 1950s cycle of mineral industry involvement of a local non-Europeanized aboriginal was as an individual employee. The employment relationship would begin with the best of intentions by both parties of permanence and terminate when the pioneering employee was unable to reconcile the attendance behaviour required by the employer and the social-sharing behaviour demanded by family and friends.Cominco Ltd. has been a mine operator and developer in the North since the 1920s. Cominco's early experiences with employment of non-Europeanized natives at the Con Mine in Yellowknife, Northwest Territories from 1938 to 1986 was a negative experience from both the employee and employer ends. A series of classic failures in employment of individual aboriginals was a large part of the history. A few Metis or natives from other areas were the permanent aboriginal employees at Con (2010). Racial prejudice was overt on the street in Yellowknife and, it can be assumed, in the workplace, as well.The history of aboriginal employment at the Pine Point, Northwest Territories operation (1964 to 1988) was somewhat better but also frustrating. The mine was equidistant (80 km) from the Dene communities of the Hay River Indian Reserve and Fort Resolution, both on Great Slave Lake. Despite a large aboriginal presence and many well-intentioned efforts, employment of aboriginals at Pine Point never got much beyond ten per cent. These would have been half local and half northern prairie aboriginals. One continuing success story was the railcar loading and covering crew led by Ed McKay, a local aboriginal. This predominantly aboriginal crew did its own recruiting and several are on Cominco pension."

Jan 1, 1995

By J. Béland, C. Giguère

"The auriferous mineralization at the Sigma-2 gold mine occurs in quartz-carbonate-tourmaline veins emplaced in a fractured granaphyre layer in the upper part of a differentiated gabbro-diorite sill. Kinematic indicators show that fracture planes were active as strike slip, dip-slip (reverse) and tensional faults.Measurements of attitudes of fractures and movement vectors indicate eight different sets that can be grouped into three systems: (I) an east-west oriented system includes a subvertical set and two other sets dipping north and south respectively; (2) a subhorizontal system of two conjugate sets bisected by a third tensional set; and (3)a system of sub vertical conjugate northeast and north-northwest trending sets.Kinematic analysis indicates that the subvertical set of the east west system was subjected to dextral strike-slip movement activated by a northwest-southeast compressive stress whereas the bulk deformation resulting from the remaining and subsequent seven sets can be explained by a protracted subhorizontal north-south compressive stress.The valuable gold mineralization is found principally in the fracture-filling veins of the subhorizontal system and subordinately in the other sets; among these other sets, the NE trending subvertical one is slightly more favourable.The over-all tectonic picture is that of an early mild dextral strike slip faulting in a ductile-brittle medium followed by a general flattening involving, first, a vertical and, later, a lateral extension by fracturing in a medium that had become brittle.The structural features are such that the differentiated sill could not be the source of the auriferous hydrothermal solutions."

Jan 1, 1990

By J. F. Hazzard, R. J. Chalaturnyk, C. Khazaei

"Various measurement, monitoring and verification (MMV) techniques are used to ensure the safety of operations in petroleum projects. One of these techniques is microseismic (MS) monitoring of the caprock. A challenge in MS monitoring of caprock is that unlike projects such as tunnelling in hard rocks, the number of recorded events are much smaller and also wide spread through the rock mass which makes interpretation of the physical meaning behind the events very difficult.In this paper, a numerical technique is introduced and validated for coupling a finite difference code, FLAC3D (Fast Lagrangian Analysis of Continua), with a discrete element code, PFC3D (Particle Flow Code). Then, a similar approach is adopted for modeling microseismic events in the caprock. For this purpose, the underburden, reservoir and overburden layers are modeled by FLAC3D. A rather small section of caprock above the reservoir is nulled in the FLAC3D model and substituted by a PFC3D inclusion. The reservoir pressures are then applied to the reservoir section of FLAC3D. Once the FLAC3D cycles, there will be induced pressures in the caprock due to its undrained response to the change in pressures within the reservoir. These induced pressures are transferred to PFC3D as boundary velocities. Then the PFC3D cycles and sends back the boundary forces to FLAC3D. This back and forth process continues until equilibrium is reached. During this process, there will be bond breakages within the PFC3D inclusion that can be regarded as MS events. An algorithm for recording the microseismic energies based on a change in local strains is also implemented. The results are then compared with real data. The effect of injection fluid temperature is also studied. No significant appearance of microseismic events was observed due to injection of CO2 in both cases (i.e. with or without considering temperature). However, this continuum/discontinuum approach seems promising for understanding the microseismic response of caprock in more detail and also using the MS data for validation of geomechanical models."

Jan 1, 2015

By G. Chung, W. Petruk, D. Doyle

"A series of tests was conducted on Carol Lake iron ore, which contains about 38 wt % hematite and 19 wt % magnetite, to establish a flowsheet for high weight yield by spirals. A pilot plant was run in parallel with the IOC concentrator to simultaneously test two flowsheets on the same feed material. The IOC concentrator processes the ore by treating it directly in a spiral circuit, whereas the pilot plant used a laconite flowsheet which had a low intensity magnetic separator (LIMS) at the front of the circuit. The LIMS produced a non-magnetic (hematite-rich) product and a magnetic (magnetite-rich) product prior to treating the ore in two separate spiral circuits. The results from about 150 tests were evaluated by chemical assays and materials balancing techniques, and a selected test was evaluated by the image analysis and materials balancing technique.The image analysis and materials balancing evaluation showed that a higher hematite recovery was obtained by the hematite spiral circuit than by the IOC concentrator spiral circuit, and a slightly lower magnetite recovery by the magnetite spiral circuit than by the IOC concentrator spiral circuit. Furthermore the hematite recovery by hematite spirals was higher than the magnetite recovery by magnetite spirals. The better hematite recovery was achieved because a higher liberation is obtained for hematite than for magnetite, and the hematite in the Carol Lake ore has a narrower grain size range than magnetite. Consequently, better spiral control can be maintained when processing a hematite-rich spiral feed, than when processing a magnetite-rich spiral feed. Since the feed to the IOC concentrator spiral is a mixture of hematite and magnetite, an intermediate hematite recovery is obtained by the IOC concentrator. INTRODUCTIONA study of characteristics that affect recoveries of hematite and magnetite from the Carol Lake ores of the Iron Ore Company of Canada (IOC), was carried out in connection with a project on designing a flowsheet for maximum weight yields. A pilot plant using a taconite flowsheet was run in parallel with the existing IOC concentrator which uses a classical iron ore flowsheet. About 150 tests were run to compare iron recoveries and weight yields by the spirals in the two flowsheets. Better iron recoveries were indicated for the taconite flowsheet, but the results were not consistent and the reasons for the observed differences were not apparent. The material from one test (Test 61), which gave better iron recoveries for the taconite flowsheet, was evaluated by the image analysis and materials balancing technique. A suite of samples was taken from 5 points in the IOC concentrator and from 8 points in a pilot plant (taconite flowsheet). The samples were analyzed to compare the behaviours of the Carol Lake hematite and magnetite in the spirals of the two flowsheets. The results provided a sound basis for further tests in designing a high weight yield flow sheet."

Jan 1, 1993

By B. N. Church, A. R. Pettipas

"The second vertical derivative method of processing aeromagnetic data from low level helicopter surveys yields results correiatable with the known geology and may be utilized to indicate possible targets for future exploration in the Silver Queen and Equity Silver mines areas, near Houston in central British Columbia . The principal zones of alteration associated with mineralization, known from detailed mapping, are further delineated and extended in a way not possible by a cursory examination of the original magnetic data.IntroductionThe second derivative method of processing aeromagnetic data is a long established procedure used to enhance the short wavelength content of the magnetic fields. Some recent exam pies of the use of the second derivative technique have been published by Chandler (p. 385), Sun Yunsheng et al. (p. 424) and Yarger (p. 223) in Hinze, 1985. According to theory, the ""second vertical derivative"" is closely related to the rate of curvature of magnetic (or gravity) fields and is particularly useful in resolving and sharpening local anomalies. The contours on second derivative maps may coincide with important features such as lithological boundaries, faults and mineralized zones.In the Houston area, central British Columbia, aeromagnetic data supplied by local mining companies provide a ready base for analyses. Examples are data sets for the Silver Queen and Equity Silver mines centred 35 km and 34 km south and southeast, respectively, from Houston (Fig. 1), (Cochrane, 1970 and Church, 1985)."

Jan 1, 1990

By A. Perucho, J. P. Harrison, A. Bedi, L. Alejano, L. Lamas, A. Sofianos, A. M. Ferrero, R. Migliazza, R. Olsson, J-F. Mathier

"In 2010, the Eurocode for Geotechnical Design, EN-1997-1:2004 (CEN, 2004), informally known as Eurocode 7 or EC7, became the Reference Design Code (RDC) for geotechnical design – including rock engineering design – within the European Union (EU). EC7 is one standard within the comprehensive Structural Eurocode suite, which as a whole has been also adopted by a number of other countries beyond the EU. EC7 is thus becoming a key design standard for geotechnical engineering worldwide.As part of the Structural Eurocode suite, EC7 requires designs to adhere to the principles of Limit State Design. However, it is not clear that current rock engineering design practice can satisfy this requirement. In addition, evidence is accumulating that EC7 is currently difficult to apply to, and may even be inappropriate for, rock engineering design. These issues may be due to the fact that the development of EC7 to date took place without any formal input from the international rock mechanics and rock engineering community.In early 2011 under the auspices of CEN (Comité Européen de Normalisation / European Committee for Standardisation), EC7 entered a formal period of maintenance which was aimed at improving the applicability and ease-of-use of the Code. This maintenance cycle will conclude in 2020 with the publication of a revised version of EC7.This paper describes a number of critical aspects for rock engineering in the context of EC7, inparticular the following:– the history of the Structural Eurocodes and the concepts they embody;– the nature of Limit State Design and the challenges and opportunities it poses for rock engineering design;– the formal means by which the Structural Eurocode maintenance cycle proceeds;– the plans currently being developed for improving EC7 with regard to rock engineering design and construction;– the unique and vital opportunity for the entire international rock mechanics and rock engineering community to comment on the Code and make suggestions for its improvement."

Jan 1, 2015

By J. Roth

"While not taking issue with the general thesis expressed in Dr. Ridge's analysis of the role of genetic concepts versus observational data in ore exploration (Ridge, 1983), the criticism could be offered that the author tends to slight the importance of conceptual (i.e. theoretical) models in mineral exploration.As a general rule, observational data in science lacks significance and utility without a theoretical construct to organize those observations. Theory in turn dictates what observations are made-and which ones are judged important. Thus, for example, prior to the elaboration-and acceptance- of the current model for volcanogenic base metal deposits, the structural aspect s of these deposits were most closely observed and studied by explorationists. The nature of the enclosing rocks and any attendant alteration was given minimal attention, and certainly didn't figure prominently as an exploration guide.Similarly, the importance of alteration features to exploration for porphyry copper-molybdenum deposits was only perceived when a theoretical model was developed to account for these aspects. Indeed, many of these porphyry copper deposits were regarded as epigenetic vein deposits by geologists of an earlier era observing and examining on a different physical scale-and with a different theoretical bias.In constructing and evaluating such conceptual models, explorationists primarily rely on observation data and proximate associations; speculative thoughts as to ultimate provenance or crustal evolution clearly play a subordinate role, as Dr. Ridge argues. This, however, should not obscure the fact that concepts and theories do indeed exert a major influence in mineral exploration."

Jan 1, 1983

By T. P. Riordon

"Major swings in the silver price since 1979, along with the ever constant fight to maintain ore reserves has forced United Keno Hill Mines Limited through several unique series of events in order to survive in the 80s.This paper is specifically meant to be a description of safety and productivity improvements achieved to ensure the survival of a silver mining community ill the Yukon. There are, however, other events and conditions that must be described to complete the story and this paper attempts to do that as well IntroductionUnited Keno Hill Mines Limited, a subsidiary of Falconbridge Limited, is the only silver producer in the Yukon. Operations are located in north central Yukon, in and around the small town of Elsa, latitude 62.5 °, about 275 road miles from Whitehorse. The Arctic Circle is about 185 miles due north of the town.Temperatures in 1986 ranged from a high of 28.5°C in July to a low of -37.0°C in November, however, much lower temperatures have been recorded in previous years. Due to the mountainous terrain the town of Elsa is completely in the shade from mid-November until early February, a period of about 12 weeks.The Elsa area, as is most of the north, is considered semiarid with an average precipitation level of about 15 inches. Vegetation, however, is quite abundant though slightly dwarfed at the townsite elevation of 3200 feet above sea level: Many of our operating and exploration portals as well as our open pits are above the tree line. Permafrost in the area has been recorded up to 400 feet below the surface."

Jan 1, 1988

"The South African Mineral Resource Committee (SAMREC), a Working Group of the SAMREC/SAMVAL Committee (SSC), under the joint auspices of the Southern African Institute of Mining and Metallurgy (SAIMM) and the Geological Society of South Africa (GSSA) developed the SAMREC Code. The Code sets out minimum standards, recommendations and guidelines for public reporting of exploration results, mineral resources and mineral reserves in South Africa. It is applicable to the reporting of all styles of solid mineralization or economic deposit. However, certain commodities, namely coal and diamonds, have specific additional reporting requirements. The Code does not apply to oil, gas or water."

Jan 1, 2003

By V. Evans

Mine lateral development advance rates currently average about 5 metres (16.5 ft.) per day. Granduc Tunnel hit 35.1 metres (115 ft.) on their best day, 12 km from the portal, single heading forty-three years ago. This Canadian mining record remains an excellent example of rapid drill and blast excavation with suggestions for improving current practice.

May 1, 2011

By R. L. Armstrong, C. I. Godwin, V. M. Kruan

"The Scheelite Dome tungsten-bearing skarn property, central Yukon Territory, is in metasediments in contact with a quartz monzonite intrusion. Contact metamorphism to biotite-muscovite- andalusite hornfels and calc-silicate hornfels is superimposed on low-grade regionally metamorphosed rocks represented by quartz-mica pelitic schist and muscovite-biotite pelitic schist.Metasediments are likely Precambrian in age, even though Rb-Sr whole-rock analyses indicate an early Paleozoic age (511±41 Ma); this apparently too young radiometric age is due to partial loss of radiogenic strontium during regional metamorphism. The minimum age of the quartz monzonite intrusion is Cretaceous at 90.4±2.6 Ma (K-Ar on biotite) and its initial 87Sr/86Sr ratio is 0.7121. The high initial ratio of the intrusion is due to the addition of radiogenic strontium from the metasedimentary country rocks and perhaps an underlying older basement.Scheelite-pyrrhotite-chalcopyrite mineralization occurs in diopside-zoisite skarn pods within the calc-silicate hornfels near the quartz monzonite intrusion. The source for lithophile tungsten is probably the same as for the granitic magma, namely Precambrian sialic basement.IntroductionThe Scheelite Dome tungsten skarn property is within the Mc-Questen map-area (NTS: 115P/16),28 km northwest of Mayo, Y.T., at latitude 63°47' north and longitude 136°15' west. The property can be reached by helicopter or by four-wheel- drive vehicle from Mayo.This paper summarizes the geology of the Scheelite Dome property, which has been described in a general way by Little (1959) and Cathro (1969). Geological mapping and sampling were done by the first author (nee Steffler) during June 1979. Field work was supplemented with detailed work at the Department of Geological Sciences of The University of British Columbia during 1979 and 1980 (Steffler, 1980). Whole-rock chemical analyses were done by Cominco Ltd."

Jan 1, 1982

By Maurizio Violo, Arjan Beqiraj, Umberto Masi

"Abstract - Four main podiform occurrences of chromite have been distinguished in the ultramafic Bulqiza massif, Albania; they are associated from the bottom to the top with: i) basal harzburgites (lower tectonite sequence), ii) dunitic lens-bearing harzbugites (middle-upper tectonite sequence), iii) layered chromitite-bearing dunites of transitional zone, and, iiii) the stratigraphically lowermost part of the magmatic section. However, only the occurrences hosted by rocks ii) and iii) are economically important.Chromite compositions similar to those of other podiform chromites are bimodal. Thus, chromites from occurrences ii) and iii) are richer in Cr than chromites from the other two occurrences. Accessory chromite disseminated throughout the massif is richer in Fe than orebody chromite, displaying similar range of the Cr/Cr+Al ratios, with accessory residue chromite matching the characteristic (Cr/Cr+Al >0.6) range of type-III Alpine peridotites. Both orebody and accessory chromites show compositional ranges correlating with host-rock compositions, i.e., the Cr-rich chromites are hosted by the most refractory ultramafic rocks. Therefore, the Cr/Cr+Al and Mg/Fetot (Cr/Fetot) ratios of chromite are useful for exploration of high-grade, metallurgical chromite ore at Bulqiza and in other massifs of similar geodynamic setting."

Jan 1, 2000

By Weimin Fu

Chondrite-normalized rare earth elements (REEs) profiles and high field strength elements (HFSEs) in rocks and minerals represent important tracers of geological processes. Of these the birdwing-shaped profile with negatively-sloped light REE ((La/Sm)N >1), positively-sloped heavy REE ((Tb/Yb)N <1), and strong negative Eu anomalies is commonly associated with large-scale hydrothermal systems or granitic intrusions. In a different way, severe deviation of Nb/Ta, Hf/Sm ratios from those of chondrite may also indicate hydrothermal signatures in the rocks involved as these ratios are generally stable and chondritic in normal magmatism as a result of their nearly identical ionic radii and charge. In this study, we present a typical setting where birdwing-shaped REE profiles together with Nb/Ta, Hf/Sm ratios unusually higher than those of chondrite, are systematically developed in a series of garnetite, quartzofeldspathic gneiss, Fe- or Mg-rich aluminous gneiss, and sulfides and magnetite. These units and associated Cu-Au mineralization form a VHMS-style hydrothermal system in the granulite-facies 1.4 Ga -1.35 Ga volcano-plutonic, arc-related Bondy gneiss complex (BGC), western Grenville Province, Canada. Outside the recognized hydrothermal system of the BGC, such REE profiles are not observed. Instead the surrounding felsic and mafic gneisses display primary trace element characteristics of island-arc magmas, suggesting that granulitefacies metamorphism did not modify significantly the trace element signatures of the protoliths. Although magmatic fractionation of accessory minerals can produce birdwing-shaped profiles, it cannot explain the extreme fractionation of isovalent trace elements (Nb-Ta) and the high Zr content of the hydrothermal rocks. Neither is it compatible with the lack of significant Nd depletion that would normally incur during this process. Following our study, we demonstrate that F-rich fluid and mineral phases enriched in LREEs and HREEs respectively must have been involved in the main hydrothermal alteration and REE fractionation process in the BGC. Preferential removal of REEs from the interstitial glass of the volcanic protoliths together with dissolution of plagioclase and subsequent external influx of HREEs and HFSEs can produce birdwing-shaped REE profiles. In turn, such profiles and/or unusual Nb/Ta, Hf/Sm ratios can be used as a sensitive marker of hydrothermally altered rocks in targeting mineral exploration.

May 1, 2003

By P. Chu, J. A. Finch, R. Li

"Bubble size plays a key role in flotation. In this paper, we examine the possibility of using passive acoustic sending to determine bubble size. Software was developed based on Short Time Fourier Transformation (STFT) to analyze the frequency of the acoustic signal emitted from the bubble formation event. Bubble size was determined from the Minnaert frequency. The acoustic-determined bubble size responded to reagent dosage, but was less sensitive than that given by imaging. The constraints of the current acoustic approach are discussed.INTRODUCTIONBubble size is an important factor affecting flotation performance. It determines the maximum available surface area for collecting and transporting mineral particles. Of interest for process control (Gorain, Franzidis, & Manlapig, 1995), it can be determined by several techniques, such as image analysis (Grau & Heiskanen, 2002; Hernandez-Aguilar, Gomez, & Finch, 2002); conductivity (Barigou & Greaves, 1992); drift flux analysis using gas rate and gas holdup measurements (Banisi & Finch, 1994); and optical sensors (Randall, Goodall, Fairlamb, Dold, & Connor, 1989). However, all these techniques have drawbacks.Acoustic analysis of the oscillatory behaviour of bubbles to extract bubble size is another possibility (Leighton & Walton, 1987; Pandit, Varley, Thorpe, & Davidson, 1992; Al-Masry, Ali, & Aqeel, 2005; Manasseh & Ooi, 2009; Leighton & White, 2012; Spencer et al., 2012). The fundamental basis is the work of Minnaert (1933) who first correlated the bubble size with its natural frequency, Equation 1:"

Jan 1, 2016

By L. S. Brooks

TIMBER HANDLING presents a problem for any mine where appreciable amounts are used. This problem is accentuated where the shaft compartments are too small to allow a loaded timber truck to be lowered in the mine cage. When Normetal Mining Corporation, Limited, found it necessary to resort to square-set mining it faced this problem of getting large quantities of timber down a shaft that was also required for hoisting ore. A &apos;timber car&apos; that could be suspended under the cage was developed to overcome this difficulty. Production started at the Normetal mine in 1937, at the rate of 250 tons per day. In 1938 a winze, known as No. 3 shaft, was sunk from the 800-foot level ?to the 1,385-foot level. This was later raised to surface and then deepened to 3,275 feet in three stages and became the main production shaft. The portion of the mine below the 3,070-foot level is serviced by a winze, locally referred to as No. 4 shaft, which has been developed for stoping down to the 3,990-foot level and which has been deepened to the 5,365-foot level. No. 3 shaft has two hoisting compartments, each 4 ft. 6 in. by 5 ft. 0 in. inside the timbers, through which the ?ore must be hoisted and timber and supplies lowered.

Jan 1, 1956

By G. Begin

"The expansion undertaken at Selbaie in 1985 necessitated an adaptation and expansion of the equipment maintenance system. This paper relates briefly the stages of transformation of the maintenance administrative structures, work methods and tools. The maintenance in a mechanized mine requires an expenditure level in the order of 20% of the total operating cost of the enterprise. Thus, the maintenance organization was modified to apply more computerized planning and follow-up, and the role of preventative maintenance was further advanced.IntroductionAs far as maintenance is concerned at Selbaie, the scenario described herein is a resume of the current situation. Although positive results have been obtained, this outline is in no way a detailed account of a fail-proof maintenance system.Once zone A-I was put into production, the expansion the mine experienced in 1985 had a direct impact on the equipment maintenance system. As centralized as it was in the beginning, the system is now partially decentralized.The over-all changes to the maintenance department demonstrate the flexibility required by organizations in new situations. In spite of the exceptional results obtained before the expansion, it became evident that both the maintenance and production sectors would have to be combined. In doing so, a more appropriate coordination of maintenance work could be obtained and the maintenance staff would obtain a more detailed knowledge of the equipment in each sector. In addition, by keeping the general and specialized departments centralized, it was possible to offset the negative effect s of a decentralized system, namely too much manpower."

Jan 1, 1990

By A. W. Davis

"The Red Rose mine is in the Rocher Deboule mountains about 8 miles east of Skeena Crossing and a like distance south of the town of Hazelton; the most northerly settlement on the Prince Rupert line of the Canadian National railway and 177 miles northeast by rail from Prince Rupert. The mine workings are on the north side of Balsam or Red Rose creek; a tributary of Juniper creek that drains via Kitseguecla river into the Skeena near Skeena Crossing. A truck road 11 miles long extends from Skeen a Crossing (elevation 650 feet) to the Red Rose mill (elevation 4; 100 feet). The mine workings lie between 5; 600 and 6; 300 feet above sea-level. Mine and mill are connected by a 1-mile aerial tramway and a tractor trail.The Red Rose claims were staked about 1910 by prospectors attracted to the district by the construction and near completion of the railway between Prince Rupert and Jasper. For a number of years interest centred in prospecting a sheared zone exposed in a ravine between elevations of 5,425 and 5,825 feet. Several adits were driven and some high gold assays were obtained in vein quartz in the sheared zone, but this work did not develop sufficient ore and the property finally closed down. In the early twenties of this century tungsten minerals were discovered in the northern extension of the vein, but nothing was done to test this deposit. Finally, in 1940, spurred by the wartime demand for tungsten, the Consolidated Mining and Smelting Company of Canada drilled the tungsten-bearing vein, and although results were none too encouraging, underground work was begun in June 1941. The latter work disclosed substantial amounts of ore. A small mill, subsequently enlarged, began operation early in January 1942 and by the autumn of 1943 some 1,194,000 pounds of tungsten concentrate had been recovered. Mining ceased in November 1943 because of orders from the Metals Controller that no more shipments would be permitted."

Jan 1, 1954

Everybody would agree that a good roadway leads to more efficient haulages by reducing haul times, smoother and safer operation for operator and less wear and tear on tires and equipment, thus improving availability and overall costs efficiency. There is a number of factors that come into play to achieve this especially when developing a mine. Excavations of Ramps and Headings: Operators should follow surveyors and layouts accurately while driving ramps. To maintain constant grades on ramps, which leads to better design control of water and easier grading of roadways. Dips and dives lead to needless over excavations and unnecessary cost and disposal of waste rock. When dressing a ramp some areas may require 2 to 3 feet of material to correct the dips and perfect to constant grade. You may ask yourself, is this all necessary? A small exercise is to follow a loaded haulage truck up ramp. At the first hump, grade change, notice the down shift and notice how far the truck travels to regain the up shift and his speed. The difference is remarkably noticeable when the grade is constant. All this leads to less driveline shock, less horsepower demand, better fuel efficiency and more productivity. Drill & Blast Patterns to control water for Ramp Headings: The drill pattern needs to allow for a ditch. A slight cross fall to form a ditch can easily be done with the lifters. The preferred side of the ditch is always the inside curve of the ramp as it has less tendency to erode roadbed material. On a level, the ditch is dictated by the sump location. A blasted ditch will eliminate water pounding and keep the roadbed dry. Water trapped in roadbed is the major cause of rollout and de-stability of roadbed. If the water is allowed to drain in the middle of the ramp it will cause erosion, movement and loss of fines and an increase in grading intervals.

Feb 1, 2008

By James F. Archibald

Testing has been accomplished to substantiate recent laboratory trials which have demonstrated that thin liner membranes, applied to rock core samples, can significantly enhance the structural performance of such rock materials. A range of Canadian polymer liner materials (MineguardTM, RockguardTM and RockWebTM) have been tested side-by-side to evaluate strength and other physical property improvements generated for two highly homogeneous, though differently sourced, granodioritic rock materials. Tests were conducted on physically similar core materials, utilizing 104 to 113 samples of each respective rock type. For both rock sample populations, cores were coated using linings at thicknesses varying between 1 and 7.3 mm, typical of the application range currently used underground by mines contemplating use of such membrane agents. Results of rock failure tests, following application of passive lining covers upon the very large sample populations of each rock type, have indicated that noticeable strength improvement and enhancement of post-yield failure characteristics can be developed by the entire range of spray-on liner materials evaluated. It is shown that all of the tested liner agent materials currently available can and do act to positively reinforce rock support capabilities of modeled core pillars. Where liner materials can be effectively placed underground, it is anticipated that they may provide similar benefit and be successfully used in partial replacement for either screen or shotcrete to provide advantageous area support for rock.

May 1, 2001

By J. H. Reiss, D. F. Bruhn, Idaho National Laboratory, Y. Jiao, D. W. Reed, Y. Fujita, D. L. Daubaras

"Bioleaching offers a potential approach for recovery of rare earth elements (REE) from recyclable materials, such as fluorescent lamp phosphors or degraded industrial catalysts. Microorganisms were enriched from REE-containing ores and recyclable materials with the goal of identifying strains capable of extracting REE from solid materials. Over 100 heterotrophic microorganisms were isolated and screened for their ability to produce organic acids capable of leaching REE. The ten most promising isolates were most closely related to Pseudomonas, Acinetobacter and Talaromyces. Of the acids produced, gluconic acid appeared to be the most effective at leaching REE (yttrium, lanthanum, cerium, europium, and terbium) from retorted phosphor powders (RPP), fluidized cracking catalyst (FCC), and europium-doped yttrium oxide (YOEu). The Acinetobacter isolate, BH1, was the most capable strain and able to leach 33% of the total REE content from the FCC material. These results support the continuing evaluation of gluconic acid-producing microbes for large-scale REE recovery from recyclable materials.INTRODUCTIONAn enhanced recovery, substitute, reuse or recycle paradigm is important for balancing the supply and demand of critical materials (DOE, 2011). The recovery of rare earth elements (REE) from recyclable materials is an important component in this model. REE are used in a variety of modern products. For example, neodymium, europium, terbium, dysprosium, and yttrium are important for applications such as permanent magnets, lamp phosphors, rechargeable batteries, etc. (Binnemans, Jones, Blanpain, Van Gerven, Yang, Walton, & Buchert, 2013; DOE, 2011; Graedel, Harper, Nassar, & Reck, 2013). Cerium and lanthanum are used in glass polishers and additives in fluidized cracking catalysts (FCC)."

Jan 1, 2016