Search Documents

By H. C. Gunning

The Privateer is the major mine of the Zeballos mining camp; with a total production from May 1937 through the first half of 1946 of $5; 610; 423 from 139; 254 tons of ore. This includes a small production from the connected Prident mine. The entire operation was closed from October 1943 to November 1945.

Jan 1, 1954

By Robert J-M Ethier

"Sequential blasting has been introduced at Mines Gaspe to reduce the harmful effects associated with the instantaneously primed blasting method. Three stages of modifications had been tried to improve this method: trials of a rectangular pattern instead of the square one, trials of lengthened hole collars at the perimeter of the blast and trials of increased inter-row delay intervals from 35 to 50 ms. Results showed that improvements to the instantaneously primed blasting method were limited by the probability of increasing the number of bootlegs.Doing these modifications allowed the definition of a general approach to improvements before the sequential blasting method was introduced. This general approach included: planning of the mining sequence, following up on the drilling, loading and tying-in of each blast, compiling and evaluating blast results, comparing results from one bench to the other and moving along with one change at a time. This approach has permitted the successful introduction of the sequential blasting method in two steps: trials of blast by rows of delayed holes and trials of hole-by-hole blasts. The optimum result has been analyzed by high-speed camera and by computer blast simulations, The actual optimum sequential blast is obtained with a CORDLINE priming system using period 15, permitted in a large drilling pattern, with an intersequences delay interval of 230 ms and an inner-sequences delay interval of 50 ms.While these modifications were being introduced, a careful study of the drilling and blasting costs was made, which showed a sharp reduction of drilling cost per tonne. Even though there was an increased use of packaged slurry the blasting cost per tonne also dropped. The reduction in cost per tonne was explained by the fact that the average energy factor was maintained while the blasting pattern was expanded.The sequential blasting method, successfully introduced at Mines Gaspe, permits blasts of better quality, reduces the drilling requirements by more than 30% and helps to achieve improved productivity while minimizing costs."

Jan 1, 1984

By Steve Forgeron, Brendan MacKenzie, Kevin MacPherson

"The geological composition of strata immediately adjacent to coal seams has a significant effect on the safe and efficient extraction of coal from underground mines of the Sydney coalfield. Geological features such as paleo-sandstone river channels, seam splits, floor rolls, paleo-soils and stone-filled rupture features can rapidly alter the competency of immediate roof and floor strata, significantly reduce the height of the coal seam, cause rapid variations in seam gradient and influence the in situ and run-of-mine quality of the coal.The impact of these features on the over-all mining operation can be significantly reduced if mine management can be for-warned of their impending occurrence. Using the information acquired from boreholes, geological mapping, x-ray diffraction analyses, microscopic studies, geophysical logs and seismic surveys, sedimentary models have been constructed which enable the mine geologist to predict, with increasing accuracy, the future occurrence of deleterious geological features ahead of the working face."

Jan 1, 1986

By Michel Aubertin

Les activités minières peuvent produire de grandes quantités de roches stériles, qui sont typiquement entreposées dans des empilements de surface, au dessus la nappe phréatique. Ces haldes peuvent occuper une superficie de plusieurs dizaines d?hectares, et s?élever à plus de cent mètres. Pour des exploitations en roches dures, les roches stériles ont usuellement une granulométrie qui contient des particules de la taille d?un sol silteux jusqu?à des cailloux et blocs de taille métrique. La structure interne d?une halde construite sur une surface relativement plane comprend généralement deux zones principales. La première zone se trouve au coeur de l?empilement, et elle est formée par la présence de plusieurs stratifications subhorizontales (avec des couches denses et lâches) due à l?effet des équipements lourds qui compactent et brisent les grains. La deuxième zone se trouve aux endroits où les stériles ont été déversés en crête, par des camions ou des butoirs, ce qui induit une ségrégation des particules sur les flancs, le long de la pente. Selon la séquence de mise en place, la distribution granulométrique et la hauteur des bancs, un grano-classement plus ou moins développé se produit, avec les particules les plus grosses au bas de la pente et les particules plus fines au sommet ; on observe aussi une stratification inclinée due à l?avancement latéral du front de déposition. Ces éléments de la structure interne d?une halde influencent la distribution et le mouvement de l?eau (et de l?air). Pour évaluer la distribution des propriétés des matériaux dans une halde, on doit usuellement avoir recours à une combinaison de techniques qui fournissent des informations sur les caractéristiques hydrogéologiques et géochimiques des roches stériles. A cet égard, certaines techniques géophysiques sont particulièrement intéressantes car elles permettent une cartographie tridimensionnelle des variations des propriétés. Les informations obtenues de diverses techniques de mesures utilisées conjointement peuvent alors être employées afin de construire un modèle numérique qui permet d?analyser les écoulements non saturés de l?eau et le transport réactif des contaminants. De telles simulations aident à mieux comprendre la réponse de la halde dans son état actuel et futur, ce qui fournit des arguments pour ajuster la séquence de déposition pour élaborer le plan de fermeture et pour sélectionner la stratégie d?instrumentation et de suivi de l?empilement. La présentation inclura un survol des diverses techniques qui ont été développées afin de caractériser les propriétés des matériaux en laboratoire et sur le terrain, et pour obtenir un portrait global de la structure interne d?une halde. Des résultats additionnels sur la modélisation du transport réactif seront aussi montrés afin d?illustrer l?influence de la structure interne d?un empilement sur sa réponse hydro-géochimique et environnementale.

Nov 1, 2008

By Young C. Kim

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. However, no formal framework for a proper analysis has existed to date. This paper summarizes the material contained in the Design Chapter Supplement (5-3) of the Pit Slope Manual. The supplement describes the results of the research effort in which a formal economic analysis framework was developed and tested through a case study. The case study results have demonstrated the practicality of the developed procedure and the availability of required data under "real-life" conditions.

Jan 1, 1979

By J. Thiriar

The electrolytic tan/chouse at CCR was recognized by management as lagging behind modem refineries in terms of productivity, energy efficiency and controls. The operation was also burdened by high maintenance costs of cells, floors and electrolyte recirculation systems. A bench marking program was started in 1986 to evaluate processes and other technology by visiting major copper refineries in North America, Europe and Japan. The basic principles necessary to optimize the operation were defined, and a program called CCR 2000 was prepared for approval of the necessary capital investments. This paper describes the results obtained to date and outlines the remaining work to complete the modernization program, in particular, the control of electrolytes, the elimination of the Baltimore groove and studies to modernize the stripping operation or adopt permanent cathode technology.

Jun 1, 1993

By C. F. Hews, P. N. Calder

"MIROC and The Mining Industry The Mining Industry Research Organization of Canada (MIROC), incorporated in 1975, is a non-profit organization sponsored by member companies from within the Canadian mining industry. The Canadian mining industry is a world leader in technological development and in organizational and human resources development. A prime objective within the industry is to retain this leadership and also improve its competitive position worldwide.MIROC is dedicated to support the objectives of its member companies and their common interest, and the objectives of the industry. In this context: MIROC's mission is to encourage the formulation of ideas to improve mining technology and methods by any source, and to foster the development and testing of promising initiatives in progressive steps from the early stages of conceptual and feasibility research through manufacture to delivery of new technology to the mining industry. In so doing MIROC plays an important role in the development of individuals skilled in mining research. Management ApproachMIROC's research program is driven by member companies who have interests throughout Canada. The board of directors approve projects that are acceptable to its members. While MIROC's basic research funding is provided by its member companies, about 30% of its annual research budget is now derived from royalties generated from previous research activities."

Jan 1, 1994

By M. Cimenti

Fuel cells have tremendous potential as power sources but much fundamental research is still required. One key component of the research is the experimental set-up used. In particular, the placement of the reference electrode is extremely significant in measuring the half-cell overpotential of solid oxide fuel cells, since differences in area, misalignments, and also differences in the kinetics of the working and counter electrodes can cause both scaling errors and frequency distortions of the measured impedance. The impedance of thin solid electrolyte cells of different electrode geometries has been calculated using the finite element method and the results compared to experimental values obtained for the oxygen reduction reaction on platinum.

Jan 1, 2005

By Brian Lewis

"IntroductionThe ion exchange process is classed as a purification and concentration stage. In the uranium industry it is used to separate, and recover uranium, from a solution produced in the leach and subsequent solid washing circuit, that contains uranium as well as some impurities. The final product from this circuit is a solution, containing uranium at a 15 to 25 fold increase in concentration, with a chemical composition suitable for the ""Precipitation"" circuit.The process is a reversible chemical ""ION"" exchange, between a solution, and solid phase, with the ""resin"" being the solid phase. Various chemical changes in the solution phase will permit the resin to remove uranium from a solution or have the uranium removed from the resin back into a solution phase. The former loads uranium onto the resin, and is called the ""adsorption cycle"", and the removal or stripping is known as the ""elution cycle"".Ion Exchange resin is a semi-rigid polystyrene spherical bead, approximately 10 to 30 mesh. It is used by placing the resin in a vessel, so that a porous bed of resin is formed, through which the solution may flow.There are many different types of vessels, and systems used to hold the resin, but it is not the intention of this chapter to describe them all, but to describe two methods used in Elliot Lake. These are the ""fixed bed"", and ""moving bed"" systems, the condition of the bed during normal operation signifies the name of the system.Chemical and Physical Characteristicslon Exchange ResinThe resin used is a strange base Anionic resin, semi-rigid, and spherical in shape. The size of the wet resin is approximately 9007o between 20 and 40 mesh. Physically the beads of resin are broken early, but some have lasted over 15 years and are still in use."

Jan 1, 1989

By Elisabeth Kolar, Rik Catthoor, Frederik H. Kriel, Rossen Sedev, Gareth Hatch, Army Research Laboratory, Craig Priest, Scott Middlemas

"This paper reports solvent extraction of rare earth elements (REEs) carried out using a microfluidic device and considers the REE loading limit of the organic phase under laminar flow. The microfluidic device contacts aqueous and organic phase streams for a precisely defined contact time (subsecond resolution) and then separates them for offline analysis. Experiments are reported examining the effect of contact time on extraction. We focus on three REEs: one ‘light’ (Nd), one ‘mid’ (Dy), and one ‘heavy’ (Yb) REE, which are extracted using Cyanex® 572. It appears that loading limits may be locally exceeded in the organic phase near to the liquid-liquid interface, where third phase deposits are observed. Third phase formation was also observed close to the liquid-liquid interface in two-dimensional confinement, showing similar third phase adsorption on glass plates. It is also shown that, under microfluidic flow, a typical first ‘split’ between heavy REEs and light REEs can be carried out without exceeding loading limits.INTRODUCTIONMicrofluidic solvent extraction has emerged as a useful tool for studying extraction of metals in a mineral processing context (Ciceri, Mason, Harvie, Perera, & Stevens, 2013; Ciceri, Perera, & Stevens, 2011; Kriel et al., 2015; Mason, Ciceri, Harvie, Perera, & Stevens, 2013; Priest, Zhou, Klink, Sedev, & Ralston, 2012; Priest et al., 2011). The main advantages are the extremely well-defined and tunable flow behaviour, large surface-to-volume ratios, short contact times, and minimisation of sample and reagent amounts. Two main flow configurations have been studied to date: droplet-based and co-flowing streambased extraction. In the former, droplets are formed at a microchannel junction (usually a T-junction or flow-focusing junction) and flow downstream as plugs or ‘free’ droplets. In our case, stream-based extraction, the chip is a plate (often glass) with embedded microchannels (i.e. with cross-sections of tens of micrometres) that carry the aqueous and organic phases in contact without forming droplets. Thus, these chips play the role of a mixer in a conventional mixer-settler and phase separation takes place by branching the streams or collection in a vessel at the chip outlet. Stream-based extraction requires stable streams that are usually supported by a particular channel geometry (e.g. guide structure or small ‘pillars’) or surface chemistry, and flow parallel bounded by the liquid-liquid interface(Aota, Nonaka, Hibara, & Kitamori, 2006; Hibara et al., 2005; Hibara et al., 2002). Phases are disengaged downstream at a Y-junction, which is a qualitative difference between microfluidic and bulk extractions."

Jan 1, 2016

By J. G. Ross

A DESCRIPTION of the block-caving system of mining as practised at the King mine of Asbestos Corporation, Limited, Thetford Mines, Que., was presented. at the Annual Meeting of the Institute held in Quebec city, in April, 1934. The paper was published in the Transactions of the Institute for 1934. There has now been recovered, by this method, one million tons of ore, and a review of experience indicates that the method was well planned and has been executed smoothly. In approaching the problem of selecting the type of mining best adapted to this deposit, the method had to be one which would be low in cost, use no wood, and not disturb the surface immediately bounding the ore-body on two sides. Prior to 1931, block-caving had been considered but rejected, as it en-tailed disturbance of the surface area which lay within a 45° angle of the lowest contemplated workings, if the practice of such mines as Ray, Miami, Inspiration, and Morency, where this type of mining has been used extensively, was followed. At these properties there have been mined large tannages at outstanding low costs, but an extensive surface area has been disturbed in each case. In some instances, townsites in the mining area have had to be abandoned, and dwellings, not considered worth moving, have been allowed to fall into the depression. A study was made of the principles involved in the various types of block-caving, the existing information on ground movement, subsidence, etc., also being carefully analysed. Toward the end of 1931, a plan was conceived whereby the country adjoining ground being caved might be held permanently in place and undisturbed. The success of such a scheme was essential to the application of block-caving at the King mine on account of property boundaries, the Quebec Central Railway right-of-way, and expense of moving buildings. Study of existing data on caving and movement of rock, caused by sub-surface excavations of sufficient unsupported area to result in failure of the backs, indicated, in practically every instance, that such movements followed certain definite laws of mechanics.

Jan 1, 1936

By Z. Wu, L. N. Y. Wong

The present study develops the numerical manifold method (NMM) as a tool to investigate the progressive failure in rock slopes. The entire processes of the progressive slide surface development related to crack initiation, propagation, coalescence and degradation to eventual catastrophic failure are successfully captured. To overcome the limitation of the original NMM associated with an improper removal of the interface cohesion of the discontinuities, the displacement-dependent cohesion removal method is adopted. Simple examples of failure of rock slopes containing different arrangements of discontinuities are modeled and their results are compared with those based on the popular limit equilibrium method proposed by famous pioneers Jennings and Jaeger. In cases of coplanar non-persistent discontinuities, close results are obtained despite the differences in the consideration of the stress concentrations at the crack/discontinuity tips. In cases of non-coplanar discontinuities, since the influence of the tensile strength is considered by both the Jaegers model and the NMM, the Factor of Safety (SF) values are similar despite the difference in the failure path trajectories predicted by these two models. The results also reveal that the original NMM without the displacement-dependent cohesion removal method is always more conservative due to the improper removal of the interface cohesion. The displacementdependent cohesion method can to some extent alleviate such a limitation.

Jan 1, 2015

By Leopoldo Gutierrez, Sergio Castro, Lina M. Uribe, Janusz S. Laskowski

"The effect of sulfite and metabisulfite ions on the amyl xanthate flotation of copper-activated pyrite, in distilled water and seawater, has been studied by micro-flotation tests and redox potential measurements. The activation of pyrite was carried out varying copper ions concentration. It was found that in the presence of copper ions in solution, sulfite and metabisulfite are able to depress copper-activated pyrite at neutral or slightly acid pH. After the addition of sulfite or metabisulfite ions the resulting pH is more acidic with metabisulfite ions. A significant increase of the redox potential of the solution was observed as copper ions concentration increased. Then, the initial reducing conditions brought about by sulfite and metabisulfite ions, change abruptly to oxidizing conditions in the presence of copper ions. Under these oxidizing conditions, the metabisulfite showed to be an effective depressant for pyrite mainly in seawater. However, sulfite was a pyrite depressant in both distilled water and seawater. Based on these results, the pyrite depression by sulfoxy-depressants during the flotation of Cu/Mo ores in distilled water and seawater is discussed.INTRODUCTIONDepression of pyrite by sulfoxy-depressants (sulfite and metabisulfite) in the presence of copper ions is an important issue. This is particularly true when pyrite depression in the flotation of Cu/Mo sulfide ores is carried out in seawater. The use of lime in seawater must be avoided because the formation of magnesium hydroxy-complexes and precipitating magnesium hydroxide strongly depresses molybdenite flotation (Castro et al., 2014). In order to solve this problem, one large plant in Chile uses sodium metabisulfite (MBS) instead of lime to depress pyrite in seawater. In plant practice, this also improves molybdenite flotation since with the use of MBS the pyrite depression is carried out at pH 6-7, instead the pH 11-12 usually employed with lime.From a general point of view, pyrite exhibits some natural floatability over acidic pH ranges and may be partially floated without thiol collectors (a coating of sulfur/polysulfides has been claimed). Therefore, pyrite flotation with xanthates is usually high in the acidic pH region, but decreases greatly at alkaline pH (Leppinen, 1990; Fornasiero and Ralston, 1992; Zhang et al., 1997)."

Jan 1, 2016

By C. Arson

We modeled mode I fracture in shale with an equivalent damage zone (CDM), a cohesive zone (CZM) and discontinuous enrichment functions (XFEM). In the Differential Stress Induced Damage model (DSID model) used in the continuum approach the total work input is equal to the sum of the energy released by crack debonding, the energy dissipated by crack opening, and the elastic strain energy stored in the bulk outside of the damage zone. In CZM and XFEM, the overall stiffness of the rock mass in the process zone drops as soon as the fracture starts propagating (unstable fracture propagation), whereas rock elastic properties in the CDM equivalent damage zone evolve smoothly with the displacement imposed at the boundary of the domain. In the CZM and XFEM, fracture propagation stabilizes after a turning point: this point coincides with damage initiation in the DSID model. As a result, the total energy of the rock mass calculated with CDM is about twice as large as in CZM and XFEM. The relative energy components of the rock mass are in the same order of magnitude and follow the same trends in the three models. This numerical study compares the evolution of dissipated energy potentials during mode I fracture propagation, and is expected to provide a basis to predict the amount of energy released by discrete fracture growth vs. damage propagation in the fracture process zone.

Jan 1, 2015

By K. P. Plucknett, Z. Memarrashidi

WC-Co ‘hard metals’ are widely used in a variety of industrial applications due to their resistance to abrasive wear, in addition to their high hardness and toughness. However, in contrast to their mechanical properties, the corrosion response of these materials is relatively poor. In the current work the corrosion mechanisms of two WC-Co cermets are analysed, with 10 and 30 vol. % of the Co metal binder, in a 3.5 wt.% NaCl aqueous solution. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential, potentiodynamic polarisation and cyclic polarisation, together with systematic analysis of the post-corrosion solution chemistries using inductively coupled plasma optical emission spectroscopy. The corrosion potential and current density were determined, following Tafel extrapolation, allowing the calculation of the corrosion rates. It is demonstrated that continuous dissolution of the cobalt phase occurs during corrosion, which is a result of poor cermet passivation behaviour, and this response increases with the amount of binder in the cermet.

Jan 1, 2015

By A. D. Akerman, D. D. Young, G. R. Baiden

The development and maintenance of underground roadways are increasingly important aspects of the modern mining process. With the trend toward automation and track-less mining, roadbeds capable of with standing increased wheel loading have proven necessary to maintain high vehicle speed and reduced maintenance costs. Concrete has been used successfully on some roadways in order to obtain the required characteristics. However, this solution usually involves unacceptable expense. The objective of the Road Router project was to create a drift floor profiling machine capable of cutting a smooth surface out of the existing rock floor of development drifts and ramps. This surface would provide a durable, high strength, low rolling resistance roadbed that would allow for reduced operating cycle times and lower maintenance costs of scoops and haulage trucks. The Road Router has the potential to offer an alternative to concrete with substantial cost savings.

Jan 1, 1997

By W. J. D. Stone

"INTRODUCTION Over the past decade, a number of publications have described the advances in High Intensity Wet Magnetic Separation. A number of significant, but small capacity installations were made and are successfully operating. These were followed some three years ago by larger installations treating ilmenite gravity concentrates; at least one machine treating 25 tons per hour of new feed was installed and is successfully operating.However, this still did not result in general acceptance that High Intensity Wet Magnetic Separation could be applied on a large scale. Neither did it dispel the feeling that High Intensity Wet Magnetic Separation was ""expensive"" and hence, confined to small scale – high value applications suchas the cleaning of tin concentrates. In addition, there is the usual reluctance of being the ""guinea pig"" which has resulted in waiting to see ""someone else"" make the first large installation decision. Such a decision and installation has now been made.Therefore, the purpose of this paper is to show that High Intensity Wet Magnetic Separation has been commercially accepted on a large scale and to show its general application to the base metal mineral industry.Examples are confined to a few specifics due to the large volume of preliminary test data that is available. The art has now reached the stage where much of the preliminary work should be taken through to serious evaluation."

Jan 1, 1971

By John C. McKay

"The five papers which follow, under the heading of ""Technology Transfer-Universities to Industry"", were originally presented at the 20th Annual CIM Conference of Metallurgists in Hamilton, Ontario. They are a unique group of papers, unique because each paper is concerned with applied research done wholly or partly in a university environment and then translated into industrial practice.Universities can rightly be regarded as one of our nation's greatest resources-a veritable storehouse of knowledge and expertise. Yet, too often, this resource is overlooked or, at best, sparingly used by Canadian industry. Of course, university-based research cannot supplant industry-based research, nor vice versa; each type of research activity has its proper role in the over-all process of technology development.University-based scientists are best equipped to conceptualize, innovate, determine viability of basic premises and to verify these at the bench or small pilot-plant level. Industry based scientists are best equipped to develop ""bench-scale"" innovations into mature manufacturing practices. Thus, university-based scientists and industry-based scientists do not compete with, but rather complement, each other. Active, relevant university research enhances industrial research provided good communication between the two ""solitudes"" is continually nurtured.Good communication between industry and university is a prime objective of CSIRA/ACRIS (Canadian Steel Industry Research Association /Association Canadienne pour la Recherches dans d'Industrie Siderurgique), The directors of CSIRA/ACRIS foster improved communication by making regular visits to universities, by sponsoring projects and by providing lists to professors of uncharted areas where basic research is needed. More can be done to improve communication between industry and university, and it is the intent of the Association to do more.The five papers sponsored by CSIRA/ACRIS are examples of good communication and healthy cooperation. It is interesting to note when reading these papers that the cooperation arose, in each instance, as a result of different circumstances. However, there is a common thread and it is personal acquaintanceship-the university scientist/professor and the industry investigator/manager knew each other prior to the initiation of the project."

Jan 1, 1982

By F. McIntosh Galbraith

EMPLOYING geophysics to find ore was for a long time considered by the Canadian mining fraternity to be a performance of dubious value: in a category somewhere between the practice of sorcery, and using a divining rod to locate underground water. With increasing knowledge, however, and with constantly improving instruments, a solid speaking acquaintance with this adolescent science is becoming an integral part of the mining geologist's stock in trade. And quite properly so: for, in the established mining districts, the ore deposits which could be easily found, by ordinary prospecting methods, have already been located. There remain; however, in almost all of the principal mining camps, areas which are covered to varying depths by glacial debris; and it is here that the obvious opportunities exist for the successful application of geophysical methods. Geophysical results must always be considered in the closest possible relation to the local geology; and, in reality, the 'doodle-bugs' are simply additional tools for the geologist (in the same category with a plane table or a microscope). The Sudbury Basin is a shining example of precisely this state of affairs. Detailed geological mapping has not significantly altered the position of the outer norite contact as placed on Dr. Coleman's original map of the district. What detailed examination has done, of course, has been to reveal the accuracy with which the contact can be placed in different parts of the district, and to show up, in consequence, areas in which further work might reasonably be expected to disclose hitherto unknown or unsuspected ore. Viewed in this light, the proportion of the norite contact which is covered by substantial quantities of overburden is astonishingly large.

Jan 1, 1939

By Kosei Ishida

To achieve renovation work without noise, the authors developed techniques of manufacturing pre-cut interior finishing components for renovation work. In this paper, to achieve the system of pre-cut interior finishing components, the authors describe a measuring method of reinforced-concrete structure by 3D laser scanner and then describe a method of making a design of pre-cut interior finishing components with the polygon model. Using these two methods, the steps of manufacturing pre-cut interior finishing components consist of the following four steps: First, measure the building shape using a 3D laser scanner. Secondly, integrate a point cloud data and retrieve the markings on the floor. Then, create a polygon model of the building based on the point cloud data. Lastly, make a drywall design using a polygon model. To evaluate the technique feasibility of manufacturing pre-cut interior finishing components, the authors have conducted an experiment of the finishing interior work of the drywall. Using pre-cut interior finishing components, the authors have been able to achieve interior finishing work without noise.

Aug 1, 2013