Search Documents

By William A. Hustrulid

A technical and economic evaluation of the potential for improving mining productivity through the use of underreamers in blastholes, specifically in relation to Minnesota taconite, Arizona surface copper and in situ mining operations is presented. Included are (1) a review of the drilling and blasting practices presently being used, (2) a discussion of current underreamer technology. (3) the presentation of a general economic cost model for underreaming, (4) the application of the model to surface taconite, surface copper and in situ mining, and (5) a summary discussion including required performance specifications, potential overall benefits, and recommendations for further development.

Jan 1, 1977

By B. W. Gandrud

This report, consisting mostly of float-and-sink data and washability curves, has been prepared in connection with an exhaustive study of coal preparation in Alabama conducted, by the U, S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators On the basis of the float-and-sink data, an attempt has been made to determine approximately the extent of ash and sulphur reduction obtainable under given conditions on coal from the mines which were sampled, In the coal-producing districts of Alabama a great deaf of attention has been given in recent years to the problem of improving preparation methods so as to obtain from various coal beds the best possible grade of washed coal. This is especially so where the washed coal is used for the making of metallurgical coke in by-product plants or where there are possibilities of using the coal for this purpose. In the manufacture of metallurgical coke, the sulphur content of the coal is a very important consideration. It is quite often the determining factor as to whether or not a certain coal can be used for coke making. In the studies which form the basis for this report, all samples have been analyzed for sulphur in order to obtain information regarding the possibilities of sulphur elimination as well as ash reduction, and the samples on which reports are made were obtained from beds that are characterized by rather high percentages of sulphur. In connection with the present investigations of coal preparation in Alabama a standardized method of interpreting float-and-sink data has been used extensively for predicting the ash and sulphur reduction and yields obtainable in a commercial washing plant from various sizes of raw coal and from the raw coal as a whole after a certain degree of crushing. This method, which will be explained in subsequent chapters, was used in interpreting the data contained in this report. The samples used for these washability studies were obtained from the following mines in the Warrior field of Alabama: Beltona mine on the Jefferson bed; Dolomite and Mulga mines on the Pratt bed; Coal Valley No. 163 and Coal Valley No. 11 mines on the Corona bed; Cedar Cove mine on the Carter bed.

Jan 1, 1932

By B. W. Candrud

This report, consisting mostly of float-and-sink data and washability curves, has been prepared in connection with an exhaustive study of coal preparation in Alabama conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators on the basis of the float-and-sink data, an attempt has been made to deter-mine approximately the extent of ash and sulphur reduction obtainable under given conditions on coal from the mines which were sampled. In the coal-producing districts of Alabama a great deal of attention has been given in recent years to the problem of improving preparation methods so as to obtain from various coal beds the best possible grade of washed coal. This is especially so where the washed coal is used for the making of metallurgical coke in by-product plants or where there are possibilities of using the coal for this purpose. In the manufacture of metallurgical coke, the sulphur content of the coal is a very important consideration. It is quite often the determining factor as to whether or not a certain coal can be used for coke making. In the studies which form the basis for this report, all samples have been analyzed for sulphur in order to obtain information regarding the possibilities of sulphur elimination as well as ash reduction, and the samples on which reports are made were obtained from beds that are characterized by rather high percentages of sulphur. In connection with the present investigations of coal preparation in Alabama a standardized method of interpreting float-and-sink data has been used extensively for predicting the ash and sulphur reduction and yields obtainable in a commercial washing plant from various sizes of raw coal and from the raw coal as a whole after a certain degree of crushing. This method, which will be explained in subsequent chapters, was used in interpreting the data contained in this report. The samples used for these washability studies were obtained from the following mines in the Warrior field of Alabama: Beltona mine on the Jefferson bed; Dolomite and Mulga mines on the Pratt bed; Coal Valley No. 16B and Coal Valley No. 11 mines on the Corona bed; Cedar Cove mine on the Carter bed.

Jan 1, 1932

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment ranges from $20,799,800 for the 1 .06- million-ton-per-year (MM tpy) mine to $84,027,500 for the 4.99-MM-tpy mine. Total capital investment ranges from $32,506,800 to $1 22,983,500 for the same mines. Corresponding selling prices for the coal range from $12.87 to $11.64 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1976

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 34,000 acres of the 58,040-acre Little Jacks Creek Wilderness Study Area (ID-111-6) in order to evaluate the mineralized resources. The study area is located in Owyhee County, 10, about 21 miles southwest from Bruneau. No mining districts are in the study area, nor were any mines or claims recorded or found. The northern half of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Little Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By John G. Palmer

Continued development of an especially impregnated silica gel capable of reversible chemical detection of carbon monoxide (CO) was reported. The affects of changes in mine-related ambient conditions on the detection catalyst's response were explored. Temperature, humidity, and several interfering gases were found to affect the detection catalyst. The interferents include hydrogen sulfide, nitrogen dioxide, acetylene (and methylacetylene), and ammonia. High humidity decreased the detection catalyst's sensitivity to carbon monoxide for some formulations. Increasing temperature generally decreased the reaction time of the detection catalyst with carbon monoxide. Badges and carriers for the visual presentation of the detection catalyst were constructed. Several variations of these devices included provisions for absorbants and filtering agents which help protect the detection catalyst from gaseous interferents. A variety of catalyst support agents were tested in an effort to find the most suitable. Included were alumina, magnesium oxide, magnesium silicate, and several forms of silica gel. In addi tion to free-flowing forms of these sorbents, thin layer chromatography plates coated with cellulose, alumina, and silica gel and newly developed PTFE entrained silica gels were examined. A limited physical, chemical, and mechanistic characterization of the detection catalyst and the materials used to prepare it has been carried out. Metal component ratio studies, spectral, analytical, pH, and rate measurements were done.

Jan 1, 1982

Electrical trailing cable used to power coal mining machinery is frequently damaged by tensile strain or crushing by mining machines running over the cable. A major problem is finding the exact location of a short or open in this cable so it may be repaired. A major problem is finding the exact location of a short or open in this cable so it may be repaired. FMC Corporation was awarded modification III to USBM Contract H0122011 to continue development and testing of cable fault locators, resulting in delivery of: 1. A prototype electrostatic/electromagnetic/ TDR transmitter and an electrostatic/electro-magnetic receiver sot that: o Locates cable faults by time domain reflectometry o Locates opens by detecting electrostatic signals o Locates shorts by electromagnetic coupling. 2. A prototype infrared detector and an infrared detector power supply that heats a shorted area by applying high current (at low voltage) and locating a short by infrared output. 3. Twelve production infrared detectors. 4. Detail drawings for all of the developed instruments.

Jan 1, 1973

By Michael Rieber

Commodity transportation by barge is possible on about 25,000 miles of navigable inland waterways in the contiguous 48 states. Barge operations are used chiefly for the movement of bulk raw materials ranging from farm products to iron ore, coal, and other bulky semi-finished as well as finished products such as steel, chemicals and petroleum [3,p.7-9]. The barge industry, unlike other transportation industries, is largely unregulated. This is because all liquid bulk commodities most dry bulk commodities transported by for-hire carriers and companies engaged in private transportation of their own commodities are exempted from Interstate Commerce Commission regulations. As a result, about 15 percent of the total ton-miles of barge traffic each year is under Interstate Commerce Commission regulation [13,p.14-25].

Jan 1, 1977

By Jonathan E. Ludlow

A field test was conducted to demonstrate and quantify the relationship between deep cutting and the creation of airborne respirable dust for longwall mining With a double-ended ranging drum shearer. The testing program was carried out on the 3 North longwall of North American Coal Company's Quarto No. y mine in Claringten, Ohio. Continuous recordings of the dust levels were made at both the midface and tail ate areas. Data were collected during 27 shifts during which time 81 complete mining, cycles took place. Both drum speed and the number of picks per line were varied systematically during the testing program to alter the depth of cut while the production rate was held constant by maintaining a constant haulage speed. The test results indicated that at the midface position, airborne respirable dust was strongly dependent upon the depth of cut as influenced by both the drum speed and number of picks. Drum speed had a much stronger effect than number of picks over the experimental range, since a halving of drum speed reduced dust levels by approximately 60 percent while removal of every other vane pick resulted in only a 2.1 percent reduction at constant production. At the tailgate position, however, neither effect was strongly apparent. A tendency for the slower drum speeds to he associated with reduced power consumption and higher haulage speeds (and therefore production rates) was also noted. It is recommended that longwall operators oper¬ate at the lowest available drum speed wherever possible.

Jan 1, 1981

By Spencee L. Willett

A sand and gravel deposit exists in the Wildrose Canyon Wilderness Study Area (WSA), Out it is limited to local use because of the distance from major markets and resulting high transportation costs. The WSA has no identified metallic minerals, oil, gas or other energy related deposits. INTRODUCTION The WSA encompasses 17,366 acres (7,028 ha) in the Panamint Range, Inyo County, California. Access to the area is by State Route 190, approximately 45 miles (72.4 km) east of Lone Pine, California and 16 miles (26 km) southwest of Stovepipe Wells, California (fig. 1).

Jan 1, 1983

By F. B. Tough, B. H. Scott

"Petroleum engineering is a comparatively new branch of engineering, with which few people, even petroleum operators and mining engineers, are thoroughly familiar. Petroleum engineers are responsible for the accurate keeping of well logs and all pertinent data upon formations encountered, for the careful analysis of such information, and recommendations as to most suitable places for drilling, for detailed study of methods of drilling, casing, and so on in order to obtain maximum production for a minimum cost.The Bureau of Hines has from time to time carried on work in all branches of petroleum engineering in the various fields of the United States. Such work is also being carried on extensively by the California State Mining Bureau, which has in its employ a number of men who have had, besides their technical training, actual experience in oil field work. This is about the only state at the present time which is carrying on this work in a definite way. It has therefore been the practice of the employees of the Bureau of Mines to go to other states and give such advice and assistance as might prove of value in development work and in prolonging the production of the fields."

Jan 1, 1920

By T. A. Sullivan

The work described in this report was undertaken to evaluate and develop techniques for determining the oxygen content of titanium and titanium alloys. Early investigations of volatilization techniques involving halogenation were unsuccessful. Later efforts were concentrated on evaluating vacuum fusion and inert-gas fusion techniques. Two vacuum fusion methods and an inert-gas fusion method were found to be satisfactory in the 0.02 to 1.00 pct., oxygen range. These methods are described in detail. The coefficient of variation by any of the three methods is approximately 5 pct, While the main portion of this paper is devoted to the vacuum and inert-gas fusion methods, a resume of other suggested methods for analyzing titanium for oxygen also is given. INTRODUCTION The Federal Bureau of Nines has conducted research on titanium metal since 1938. This research included development of the Kroll process for the production of titanium (2)4, various sodium reduction processes for making titanium metal and lower valent titanium chloride-sodium chloride mixtures (17), and a fused salt electrolytic process for Me production of high-purity titanium metal and the recovery of titanium by electrorefining from off-grade materials (20).

Jan 1, 1961

By Lisa A. McDonald

The environmental compliance process affects all aspects of hardrock-mining operations, from exploration through post-closure. The primary components of the environmental compliance process are requirements under the National Environmental Protection Act of 1969 (NEPA) and the permitting requirements associated with various other federal, state and local laws. This study considers the Greens Creek Mine and the development of two other projects (Alaska-Juneau & Kensington). These mines were used as the foundation for a case study of the impacts of the environmental compliance process on hardrock-mining activity in Southeast Alaska. The case study presents the institutional and legal requirements, followed by a discussion of the impact of this process on the production and timing of the three mines. The results of this preliminary study reveal some interesting findings, some expected and others unexpected, regarding the impact of the permitting process on the exploration, development and (proposed) operation of the three mining projects in the Juneau area. Determining the cost of compliance with these requirements is an important step in evaluating the appropriate course of action to protecting the environment while providing the necessary raw materials needed for society. This preliminary study highlights the initial starting point for such an analysis.

Jan 1, 1992

By David E. Swanson

The U.S. Bureau of Mines undertook a basic investigation of collimated abrasive water-jet behavior because a more complete understanding of the fundamental process may lead to further technical advances. Laboratory experiments used 2-mm water-jet nozzles and new entrainment apparatus to analyze collimated abrasive water jets operating under varied conditions. Maximum water pressure was 69 MPa to permit use of conventional hoses with a burst-to-operating-pressure ratio of 4. Nozzle and induction line pressures, abrasive induction rates, and jet reactive thrust forces were recorded for each operating condition. Average jet velocity and power were determined from component mass flow rates and reactive thrust force measurements. Relative velocity and cross-sectional distribution of abrasive particles were determined using impact analysis techniques. Other jet characteristics were determined photographically. Properties of free water jets, collimated water jets, and collimated air-water jets were determined for comparison.

Jan 1, 1989

By C. M. St. John

A series of analyses of possible mining excavations associated with the development of copper nickel deposits of the MINNAMAX site in Northeastern Minnesota is presented. Specific areas such as roof and pillar stability and excavution orientations are addressed. The majority of these analyses were conducted using a boundary element method but some cases were also analyzed using the finite element method. Comparable results were obtained using the two methods but the boundary element method required less data preparation time and computer run time. Results of the analyses, as well as indicating the capabilities of geotechnical numerical models, provide some insights into behavior around multiple excavations in jointed rock.

Jan 1, 1979

By R. K. Koch

The vapor pressures of liquid titanium and liquid platinum were studied under the Bureau of Mines program for the determination of thermochemical data on the transition elements. Beating was done in a 2-kw electron-beam furnace with a water-cooled copper crucible to contain the melt. Temperature was measured with a disappearing-filament brightness pyrometer. The vapor pressure data for liquid titanium in the range 2,008° to 2,379° K are represented by the least-squares derived equation [log p (atm) = 6.268 - 22, T] Two series of determinations were made on liquid platinum. Results of the first series are expressed by the least-squares derived equation [log p (atm) = 8.240 - 30,460T] for the range 2,0860 to 2,4200 K. Results of the second series are expressed by the least-squares derived equation [log p (atm) = 7.795 - 29,580 T] in the range 2,045° to 2,442° K. Third-law evaluations of each series gave mean standard heats of sublimation of 112.4 kcal/mole, 133.3 kcal/mole, and 133.8 kcal/mole for titanium first series on platinum, and second series on platinum, respectively. Second-law heats of sublimation and equations for heats, free energies, and entropies of vaporization were obtained from sigma plots of each data set.

Jan 1, 1969

By Oscar Lee, B. W. Gandrud, F. D. DeVaney

"IntroductionFlue dust which results from the smelting of ores containing appreciable quantities of fines is one of the troublesome products of iron blast-furnace practice. Gases issuing from the furnaces at a high velocity carry small particles of coke, ore and flux into dust-collecting chambers. These particles constitute the flue dust. Lasses of iron ore through the production of flue dust vary between wide limits in the different furnaces, and depend on a number of factors, such as size and design of furnace, amount of fines in the ore, the operating conditions and the blast pressure.Blast-furnace operators of the Birmingham district keenly realize this waste. The ores are comparatively low grade and require more fuel than is ordinarily used elsewhere. Hence the flue dust is low in iron content and high in coke. As a result it is not in suitable condition for direct sintering. In many other iron and steel centers direct sintering is a common practice. In the Birmingham district efforts have been made to prevent this loss by recharging the dust into the furnace, but, as might be expected, a material fine enough to be blown out once will very likely be carried over again.In general, the flue-dust losses in this district will average 250 pounds per ton of pig iron produced, but at times the losses at different furnaces are substantially higher or lower than this figure. On the basis of the present rate of pig-iron production, the annual loss of flue dust exceeds 300,000 tons. The iron content of the dust probably averages 25 per cent, therefore about 75,000 tons of iron is wasted yearly, or about 3 per cent of the iron mined is lost in flue dust."

Jul 1, 1926

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984

By Walter W. Fisher

A study of copper cementation on iron was initiated to determine the effect that deposited copper has upon subsequent cementation. A microscopic investigation of cementation on an iron surface showed that cupric ion precipitates predominately on a growing copper deposit attached to the iron surface. A kinetic study of the cementation process in a revolving drum showed that the cementation rate is enhanced by the copper deposit attached to the iron surface and by the discrete copper particles of a cement copper slurry. The kinetic study also indicated that the character of the deposit is affected by the major anion in the solution. The cementation process is visualized to occur as a series of electrochemical cells in which cupric ion precipitates on copper dendrites attached to the iron surface.

Jan 1, 1973