Search Documents

By L. F. Willmott

The Bureau of Nines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipe- line for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

This appendix is composed of five sections, each of which is tabbed for ease of access. The sections are as follows: ? Fire incident report forms for underground mine fires. There is one form for each incident listed in Table II-1a. They are ordered chronologically with incident numbers corresponding to those in Table II-la. ? Fire incident report forms for surface mine fires. There is one form for each incident listed in Table II-lb. They are ordered chronologically with incident numbers corresponding to those in Table II-lb. ? Journal article report forms. There is one form for each article reviewed. They provide supplemental information to that contained in the fire incident report forms for selected fires. Index 11-14 keys the journal article report forms to the appropriate fire incident report forms. ? Non-reportable incident descriptions for underground mine fires. This is a listing of underground fires for which MSHA regulations do not require formal reports. ? Non-reportable incident descriptions for surface mines. This is a listing of surface fires for which MSHA regulations do not require formal reports. This appendix is intended to be used in conjunction with the tables and indexes contained in Volume II of this report and, as such, should be considered an integral part of Volume II. The indexes in the body of Volume II provide a means of ready reference to the underground and surface mine incident report forms. For those readers with interests other than those indexed, Tables II-la and II-1b can be used to locate specific incidents of interest. Complete incident information can then be obtained from the corresponding report forms in the first two sections of this appendix.

Jan 1, 1980

By Dale William Avery

Thirty mines and prospects were studied; 22 are within the Dolus Lakes RARE II area. Three properties within the area and one adjacent to it were determined to have indicated or inferred gold, silver, or molybdenum resources (fig. 1 and table 1) associated with quartz veins and shear zones or quartz-pyrite stockworks in granodiorite. Five other properties in the area and three just outside have potential for the discovery of gold and silver resources. Minor amounts of very fine-grained placer gold are in glacial outwash in and near the area. The John G. Carlisle Mine (fig. 1, no. 9) produced 120 oz (3.7 kg) of gold between 1897-1899. The Independence Mine produced 481 oz (15 kg) gold, 197 oz (6.1 kg) silver, and 189 lb (86 kg) of copper between 1926 and 1935. These mines are adjacent to the study area's northern boundary.

Jan 1, 1983

By Gustav Wirth

"ABSTRACTIn exothermic and endothermic catalytic reactions, control of the temperature is of utmost importance. Basic calculations are developed for determining catalyst volumes of various types of reactors that give particular temperature distributions, and the individual designs are compared.INTRODUCTIONA narrow range of permissible operating temperatures characterizes many, catalytic reactions, and yields of the desired product are reduced sharply if operating temperatures fall outside of this optimum range. In order to achieve close temperature control, reactors with internal heat exchange have been developed in which thin layers of catalyst are located between cooling surfaces.The temperature distribution for an exothermic reaction in such a thin catalyst layer is shown in figure 1. Reactive gases flow downward through the catalyst section, which is 2so wide. It is assumed that a constant amount of heat is generated per unit of bulk catalyst volume, and that this heat is entirely removed through the walls. Consequently, except for a short section at the entrance of the reactor, the heat of reaction is not available for raising the temperature of the gases. Thus, at all points equidistant from the axis, the temperature is the same throughout the entire reactor. At the middle of the gas stream, the temperature is designated as uo. Traveling radially from this point, the temperature decreases because of the removal of heat through the walls and reaches, in the vicinity of the cooling surface, the value u1. Over a relatively narrow zone of width, b, the temperature falls to the value u2 at the cooling surface. Because inadequate data are available on heat-transfer coefficients for a gas flowing through a porous bed, and also because the narrow zone, b, is probably without effect on the reaction by virtue of its low temperature, the temperature drop in this zone at the cooling wall was disregarded. The following calculations were made on the basis of the temperature drop (u0 - u1) resulting from heat conduction within the main body of the catalyst bed only."

Nov 1, 1950

By W. B. Tarpley

This program was conducted to demonstrate the unique advantages of suppressing methane ignition in underground mines by use of Energy & Minerals Research Company's thixogel fire extinguishing system, which stably suspends dry powder extinguishing agent in thixotropically gelled liquefied gas extinguishant. As anticipated, the project demonstrated thixogel system advantages of: 1) capability to disperse state-of-the-art powders in thixogelled Halons; 2) non-agglomerating stability for dependable expulsion; 3) stability in storage for long shelf life; 4) virtually in¬stantaneous dispersion; 5) expansive cloud formation; 6) reach and re-forming around obstacles; 7) at least twice the extinguishant effectiveness; and 8) compatibility of use with Fenwal bottles and MSHA canisters. Thus, it should prove a superior explosion/fire suppressant for coal face cutters and triggered barriers, as well as for motorized equipment, electrical equipment and the like.

Jan 1, 1981

By F. S. Kendorski

This report presents the results of a search for viable-self-drilling roof bolt concepts, detailed development, design, and manufacture of such bolts that drill their own holes, and testing in the laboratory and in the field in two different coal mines of three self-drilling roof bolts. Three new types of bolts were designed and tested, which drill their own holes and then anchor in continuous operation. These were a spring-actuated mechanical expansion shell, a slot and wedge, and a self-contained resin anchor bolt. Such bolts when fully developed for mine use would allow safer and remote installation of ground support and increase productivity. Recommendations are given for further work to improve drilling and anchorage performance.

Jan 1, 1979

By Alden H. Emery, J. J. Forbes

"IntroductionThe data contained in this paper were collected during the course of an investigation which covered 15 representative coal mines in 6 coal-mining States. The purpose of the investigation was to determine by atmospheric sampling how much dust was raised into the air during the various operations of coal mining, such as undercutting with machines, loading coal by hand, and transporting it from the working face to the surface. The data thus obtained were considered from two angles - namely, the possible physiological effect of inhalation and the explosion hazard of the dust. No attempt will be mode to discuss the former factor in this paper.CONDITIONS OF MININGThe mines in which this investigation was conducted were considered representative, and it is believed that the results obtained will suffice for the average dustiness encountered in most coal mines. .All of the coal mined was bituminous, from beds 30 to 120 inches thick. Only the ordinary room-and-pillar system of mining was employed. Daily production ranged from approximately 700 to 1500 tons and the men employed from 150 to 450. Coal was undercut by short-wall mining machines in all mines, with the exception of one in which pick mining was employed. Loading at the face was done by miners; none of the mines used mechanical loaders. Electric drills, both for brushing roof and for shooting coal, were commonly used although some roof work was done with jack-hammers and a. little of both with augers. Coal was hauled by motor, mule, or rope power in end-gate cars with capacities ranging from 1600 to 3600 pounds. With few exceptions, coal was won at the face by dry methods - that is to say, no water was employed fox wetting down the dust either during undercutting, loading, or transportation."

Feb 1, 1927

By C. Lurie

This final report describes the work performed by Gulton Battery Corporation under USBM Contract No. HO-112033, entitled "Research and Development on Lithium-Nickel Fluoride Batteries For Mint Life Support Equipment". The lithium-nickel fluoride couple was chosen For this investigation because of its high theoretical energy density (626 Wh/lb), its ability to operate at ambient temperatures and the fact that it showed promise as a secondary system. The theoretical energy density of the lithium-nickel fluoride couple is ten times greater than that of the widely used lead-acid battery and three times greater than the silver-zinc battery which has the highest theoretical energy density of the commercially available secondary systems. The experimental program first evaluated the cell components individually. The results of these studies then formed the basis for investigations of cell performance using experimental three-plate cells. These cells consisted of one nickel-fluoride and two lithium electrodes. All work was performed in a glove box under an argon atmosphere which was sufficiently pure to maintain the shiny appearance on freshly prepared lithium surfaces. The major portion of the work effort was concerned with the nickel fluoride electrode. Binder, conductive diluent, fabrication technique, as well as the nickel fluoride active material itself, were considered. Criteria for binder materials were established and six classes of materials encompassing thirteen binders were evaluated. The candidate materials were initially screened for appropriate chemical and physical properties and finally evaluated in three.-plate cells, Two epoxy powders emerged as the most promising binders. Two types of conductive diluent were evaluated. The first is a carbon black of low bulk density and high surface area. This material is a good conductive diluent; however, electrodes fabricated with it lacked good mechanical strength. It was hypothesized that a uni¬form, small particle size, low specific surface area would improve the mechanical properties of the electrodes. Therefore, two samples of graphicic materials, milled to uniform powders in the one-to-ten micron range were evaluated. Electrodes prepared with the graphitic materials had superior mechanical properties, However, their electrical performance was significantly poorer and voltage losses of 0.2 to 0.3 volts were observed. Several electrolyte solutions were evaluated. N-Methyl-2-Pyrrolidone was tested but found to be incompatible in the presence of lithium. Lithium perchlorate, lithium hexafluoroarsenate, and lithium bromide were tested as two-component electrolytes in propylene carbonate solvent and their performance compared with that of the single electrolyte solutions, Lithium perchlorate gave the best performance. Lithium hexafluoroarsenate was also evaluated in methyl formate and appears to give equivalent performance. The lithium perchlorate-propylene carbonate system is preferred as it is easier to handle and less expensive.

Jan 1, 1973

By F. L. Wideman

This report describes a computer program that is used for the calculation of the coordinates and elevations of subsidence survey pins located by intersection. This program was developed for the Federal Bureau of Mines by the Numerical Analysis Laboratory, University of Arizona. These calculations, although relatively simple, are both tedious and time-consuming when computed with a desk calculator and trigonometric tables. In this survey, a large number of pins were surveyed repeatedly, and it was evident that both time and money could be saved by using a digital computer.

Jan 1, 1962

By Glen C. Ware

The Bureau of Mines determined the factors involved in the corrosion of starting sheets used in the production of electrolytic zinc with the ultimate purpose of adapting zinc starting sheets to commercial practice . Under present practice , zinc is electrodeposited on aluminum cathodes and subsequently stripped for melting . The use of zinc instead of aluminum would eliminate the need to strip the deposit , thereby reducing the cost of handling and melting it , but zinc has not been suitable because it was too vulnerable to the corrosive attack of the electrolyte . Serious attack was found to be limited to the areas of the cathodes situated immediately above the surface of the electrolyte and to re - entrant corners . It was possible to avoid solution - level corrosion by immersing the starting sheets completely , exposing only a relatively heavy suspension member to solution - level attack . Zinc starting sheets could be made as reliable as aluminum and could be continued in residence for periods up to 39 days . Periods as long as a week were feasible under conditions similar to those found in commercial practice . A test of zirconium as a starting - sheet material showed that it promoted corrosion of the deposit to a lesser extent than aluminum and that the deposit adhered less tenaciously . These two properties lend themselves to the development of ways to strip deposits mechanically from zirconium starting sheets . Titanium was unsuitable for use as a starting - sheet material .

Jan 1, 1963

By Fredrick L. Johnson

In deposits of the John Muir Wilderness, tungsten is the principal metallic element. Gold, silver, copper, and molybdenum could be recovered as by-products from most of the tungsten deposits. More than 1 million tons (0.9 million t) of tungsten resources are estimated to be along the fringes of metasedimentary roof pendants. Gold-silver deposits and silver-copper-lead-zinc deposits with small resources are found at several localities. The association of metal deposits with the intrusive-metasedimentary rock contacts and the widespread existence of these contacts, suggests additional resources exist. The area has no known potential for coal, oil, gas, or geothermal energy.

Jan 1, 1981

By Richard Rittenhouse

This program was to develop a new base line system for automated continuous room and pillar type mining. The primary requirement estab¬lished for this machine is that the machine be capable of mining and bolting simultaneously. Additionally, this machine was to provide temporary and permanent roof control, have a productive - full - face semi-automatic mining system, leave a clean entry outby the machine, provide maximum operator protection, provide effective dust suppression and provide air scrubbing to restrict respirable dust to permissible levels. The machine has effectively demonstrated the ability to mine and bolt simultaneously. Additional above ground operation, testing, and time studies are recommended to further verify the machines abilities. Design improvements are recommended for future generation AES machines. These relate to marginal design areas such as side loading on vent duct lift cylinders, etc., that will not impair additional testing of the existing machine.

Jan 1, 1983

By Michael S. Miller

In 1984, at the request of Bureau of Land Management, the Bureau of Mines studied 8,500 acres of the 20,250-acre Seven Blackfoot Wilderness Study Area (WSA) consisting of all 3,950 acres of MT-024-657A and 4,550 acres of the 4,850 acre MT-024-657B in order to evaluate the mineral resources. Within this report these 8,500 acres are referred to as the study area. Located about 30 miles northwest of Jordan, MT, the study area is underlain by outcrops of Quaternary alluvium and Cretaceous to Paleocene sandstones, shales, clays, and coal. No mines or prospects were found in the study area. Except for some current interest in petroleum and natural gas, there has been no mineral exploration activity in the study area. The study area contains subeconomic clay, placer gold, and coal. Land within the study area is leased or under lease application for oil and gas.

Jan 1, 1986

By Forrest T. Moyer

INJURY experience and employment data are presented in this chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume II. The 1962 figures are preliminary summations which are subject to revision. They were compiled from all reports from producers received by the Bureau of Mines through April 15, 1963. The data for metal, nonmetal (except well and brine operations), stone, and sand and gravel operations were collected by a mandatory reporting system under the provisions of the act of September 26, 1961, Public Law 87-300 (75 Stat. 649). The act authorized the Secretary of the Interior to study the various aspects of safety in metal and nonmetal mines (excluding coal mines) and report the findings 2 years sub-sequent to the enactment of the law. Data on nonmetal well and brine plants and nonferrous reduction plants and refineries were reported voluntarily by the operators. METAL MINES Preliminary data for the metal mining industry comprise reports on 1,871 mines and pits. The combined fatal and nonfatal injury-frequency rate was 31.95 per million manhours in 1962, a decrease of 8 percent from the similar rate of 34.54 in 1961. Metal operations reported a total of 61 fatal and 3,201 nonfatal injuries.

Jan 1, 1963

By W. G. Phillips

This report presents results from a study whose objective was to evaluate noise control options for existing equipment used in metal and non-metal processing plants. This equipment performs 3 basic functions, crushing, grinding to a point where the product can be liberated from the waste, and agglomeration A the product. Specifically, the study was directed towards taconite processing since the extreme hardness of taconite results in high noise levels and in considerable maintenance of the processing equipment. Both of these factors make this process a very challenging noise control task. Plants processing other ores use similar equipment, consequently the results of these studies should he applicable to a wide variety of plants. The report presents the source diagnosis and potential retrofit noise control treatments for fine screens, mills, crusher sizing screens, and vacuum disc filters. Estimates are make of the noise reduction from each treatment. The report concludes with recommendations for future research on each piece of equipment.

Jan 1, 1978

By Henry Kreisinger, John Blizard, B. J. CROSS, C. E. Augustine

This report gives the results of 26 tests of a four-pass Edgemoor boiler fired with powdered coal at the Lakeside station of the Milwaukee Electric Railway & Light Co. The tests were made by the fuel section of the Bureau of Mines in cooperation with the research department of the Combustion Engineering Corporation and the operating department of the Milwaukee Electric Railway & Light Co. The object of the tests was to determine the thermal efficiencies and capacities obtainable by burning powdered coal under large central-station boilers, and the possibility of operating such boilers continuously at high efficiency and capacity without destructive effect on the furnaces and without difficulties in refuse removal. In any system for burning pulverized coal the furnace is the most important part because, to justify the cost of pulverizing, the powdered coal must be burned with higher efficiency than coal fired with mechanical stokers. In other words, it is the furnace that by giving higher thermal efficiency must pay for the installation, maintenance, and operation of the pulverizing equipment. No matter how simple the apparatus for the preparation of pulverized coal may be, or how simple the pulverizing process, unless the furnace is so designed that it can be operated continuously with high thermal efficiency, the whole system is a failure. For high thermal efficiency the coal must be burned almost completely with low excess air. But low excess air and complete combustion give high furnace temperature, which in turn causes erosion of the furnace lining and fusion of the ash; and removal of the fused ash is difficult. The necessity of complete combustion with low excess air thus brings with it these two important problems in the design of a furnace for burning powdered coal: 1, Prevention of erosion of the furnace lining; 2, easy removal of refuse from the furnace. For the purpose of solving these problems, the boiler tested was equipped with a furnace having hollow walls, through which about 60 per cent of the air needed for combustion passed before it entered the furnace. By passing through the hollow walls, the air cooled the furnace lining and prevented excessive erosion. A water screen was placed in the furnace about 3 feet above the bottom to keep the refuse deposited at the bottom from fusing and to make its removal easy. The design of the furnace, water screen, and burners was based on the experience gained in the previous cooperative tests1 with a smaller furnace, experimental water screen, and burners at the Oneida Street station of the Milwaukee Electric Railway & Light Co. The boiler tested had 13,057 square feet of heating surface. It was one of eight boilers fired with powdered coal, and was designated as boiler No. 8. The Lakeside station is the largest central station in the world that burns powdered coal exclusively. The coal used in the first five tests came from Illinois. The fuel in the other tests -:vas a mixture of Illinois and Pittsburgh coals.

Jan 1, 1925

By Sam S. Taylor

[The discovery of many oil fields in Illinois since 1936 and their rapid development have brought tine problem of brine disposal to the foreground in that State. The ultimate magnitude of the is not yet known, but already it is great enough to warrant technical investigation. The Bureau of Mines, therefore, has made a general survey of the methods of handling oil-field brines in Illinois and has studied in detail three subsurfaces disposal systems.]

Jan 1, 1940

By James S. Browning

[The objective of this project wan to determine the technical feasibility of recovering the associated copper, lead, and zinc from the pyrrhotite axe, of the Great Gossan lead, which has bon pined only for it:, sulfur and iron contents so far. The report constituted a description and discussion of small-scale Preliminary studies. This great pyrrhotite or body has strategic value, inasmuch it contains considerable quantities of zinc, copper, and lead, as well as the iron rend sulfur. The recovery of the: copper, lead, and zinc, associated with certain of the pyrrhotite ore bodies, could augment our domestic supply of these metals.]

Jan 1, 1953

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski County, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the eighth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is no followed by a description of each deposit developed in that half township. The 14 half township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations at those holes show on figure 13 in volume I. The descriptions of the deposits developed are followed by complete detailed logs at the drill holes. Many at the widely spaced exploratory holes did not discover bauxite of minable thickness and gra.de. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion covering that area.

Jan 1, 1948

By D. R. Corson

The Bureau of Mines instrumented an operating stope in a deep vein mine to determine the amount of wall closure and the magnitude of loads imposed on a backfilled stope. Hydraulic pressure cells used to monitor pressures in the fill) with bolt closure points to measure vein-wall movement and the procedure for their installation) are described) and the results of the laboratory calibration analysis of the reliability of these cells are given. An attempt to monitor density and moisture changes in the backfill with a nuclear density-moisture device was only partly successful) owing to either deformation of access tubing or relative displacements of the vertical vein walls relative to the emplaced tubes. Data from the instrumentation indicate vein-wall closure in excess of 20 inches and pressures within the fill approaching 600 psi. Analysis) incorporating field data with results of laboratory tests of the compressibility of timber and tests defining the constrained moduli of the fill) points out the limited restraint to vein closure offered by timber sets. Ground movement induced by mining activity could be more effectively con-trolled by the use of densely compacted backfill.

Jan 1, 1967