Search Documents

By C. J. Cohen, L. A. Dahners

"SUMMARYA method has been developed for surveying, drill holes without lowering into the hole any surveying equipment other than an etch tube. The orientation of the rods at the collar of the hole is maintained as the etch tube is lowered. The attitude of the etch ellipse in depth with respect to the rod orientation at the collar can then be observed. This relationship permits the bearing of the hole in depth to he calculated. The rod orientation is maintained during the lowering by means of a pair of alinement clamps. One clamp is fastened to the top of each rod as the rod is coupled and is removed when the alinement has been transferred to the other clamp at the top of the next succeeding rod. A particular advantage of this survey technique is that surveys can be readily made in magnetic country rock.PRINCIPLE OF THE TECHNIQUEAn axial lamina of the column of drill roes is the lamina in which one fiber would be the centerline of the rods. In the new survey technique, the rods are fed into the hole in such a manner that the axial lamina of each successive rod maintains its position at the collar of the hole. In depth, as the rods bend in following the drill hole, the axial laminae also bend. The lamina that was originally vertical will, in general, be tilted away from the vertical. The trace of this lamina is marked on the glass etch tube before the tube is lowered in the hole. The axial lamina that becomes vertical at the survey station is recognized as that axial lamina which contains the long axis of the etch ellipse. The angle between the lamina originally vertical and the lamina vertical at the survey station is thus measurable. When the vertical axial lamina at one survey station has been determined by the etch ellipse at that station, angle R between this lamina and the vertical axial lamina at the next survey station becomes measurable also. By moans of angle R, and dip angles D1 and D2 at the two stations, the change in bearing (z) of the drill hole between the two stations can be calculated."

Aug 1, 1944

By David E. Emerson

An improved method and apparatus for determining the impurities in helium by preconcentration and subsequent analysis by mass spectrometry are described. Preconcentration of the impurities is accomplished by passing a known volume of helium, at slightly above atmospheric pressure, through a metal coil and trap assembly immersed in liquid helium. The concentrated impurities are then analyzed by mass spectrometry. This method can detect impurities in the range of 0.01 to 600 ppm with an accuracy of better than ±0.05 ppm at the 1-ppm level. One operator can analyze 15 samples in an 8-hour day.

Jan 1, 1970

By H. E. Peterson

A study was undertaken by the Bureau of Mines to develop a simple, reliable test for field detection of selenium in rocks and soils. Two methods are described for qualitative detection of selenium, dependent upon its form of occurrence and the presence of interfering constituents in the sample. Both methods involve fusion of the sample in a test tube to form elemental selenium that will volatilize and condense as a red deposit on the cooler upper portion of the test tube. The methods are sensitive to 10 parts per million, (p.p.m.) equivalent to 0.001 percent, and can be made semiquantitative by using suitable standard samples. INTRODUCTION Although selenium is widely distributed in the United States, the known deposits are either so small or so low grade that they cannot be processed economically for selenium alone-4/ At present, commercial production is a byproduct of the smelting and refining of base-metal ores, particularly copper.5/ About 0.75 pound of selenium is recovered per ton of electrolytic copper, and small amounts are recovered by special treatment of assorted smelter dusts and fume products. Since selenium is a strategic metal in short supply, new sources are being sought by both Government and private interests.

Jan 1, 1957

By H. B. Humphrey, J. J. Forbes

"In accident prevention, a study of statistical data is necessary to determine primary causes of accidents to devise means to eliminate causes at the original sources. Explosions in coal mines of the United States during the 10 years ending December 31, 1931, ranked third in the causes of fatal accidents; they constituted 16.2 per cent of all fatal accidents in bituminous mines and 8.4 per cent of all fatal accidents in anthracite mines. A study of coal-mine explosions in Pennsylvania, with approximately 160,000 men employed in anthracite mines and about 145,000 in bituminous mines or about 205,000 out of -the approximately 525,000 men employed in all coal mines of the United States, should give information of value to all persons endeavoring to reduce or eliminate coal-mine explosions. This circular reviews explosions of gas or dust or of both in the coal mines of Pennsylvania to show the hazard of gas and dust, to point out the influence of certain factors in causing explosions, and to emphasize the efficacy of explosion-preventive measures.The data published annually by the State Department of Mines and of the United States Bureau of Mines were used in compiling the tables of explosions. Through the cooperation of W. H. Glasgow, secretary, Department of Mines of Pennsylvania, and his assistants, many doubtful cases were clarified, so that as far as recorded the history is comparatively complete. Figures used in compiling some of the tables were furnished by W. W. Adams, chief statistician, demographical division, United States Bureau of Mines.Anthracite in the Wyoming Basin of Pennsylvania was used locally by gunsmiths in 1755, by blacksmiths in 1769, and as domestic fuel in 1808.Mining and shipments developed slowly between 1806 and 1812, but more rapidly after that.Early mining along the outcrops gave essentially no trouble from gas, but by 1870, when State inspection was established, explosions were frequent; ventilation was crude and accumulations of gas were generally ""brushed"" or burned out.Table 1 lists 1,232 ignitions and explosions of gas in anthracite mines from 1870 to 1932, inclusive, every one of which was accompanied by loss of life. Some details are given of 110 representative cases in which five or more lives were lost or in which it appeared that some violence was present.During the period 1870 to 1932, inclusive, gas explosions caused 2,213 fatalities, or an average of about two deaths for each ignition or explosion. Records are not available as to the number injured in these and in other explosions where no deaths occurred, but from a study of explosion reports it appears probable that the number injured exceeds the number killed. In the 110 cases described, 599 were killed and 294 were injured. As shown in Table 2, fatalities from gas explosions averaged 8.3 percent of the total fatalities in Pennsylvania anthracite mines from 1870 to 1931, varying from 6.0 percent in 1931 to 13.1 percent in 1927."

May 1, 1933

By Robert W. Freedman

In the Bureau of Mines study, a filter with a 20-by 20-inch-square cross section was inserted into the exhaust ducting of a 4-stroke-cycle, 90-hp diesel engine, and the efficiency of removal of total particulate was measured gravimetrically as a function of time. Removal efficiencies were close to 90 pct during the main portion of several extended runs employing several combinations of filter beds. Variations in engine load had little effect on collection efficiency. Particle size as measured by a Bureau-developed online instrument centered on 0.07 m based on number count. Removal efficiency increased rather sharply for both larger and smaller particles.

Jan 1, 1979

By Charles A. Seitz

This Bureau of Mines report describes an automatic and continuous transducer-drift compensator. The compensator formed a part of the instrumentation used to indicate the saturation by hydrogen of a cryogenic, adsorption column. It has a variable delayed-response characteristic and will respond only to signals having rise times faster than component drift times. Zero drift due to varying ambient conditions and component aging is nullified. Equations relating the output as a function of the input signal are given.

Jan 1, 1981

By M. W. Von Bernewitz, E. H. Denny

The use of oxygen breathing apparatus during rescue and recovery operations at both coal and metal mines has become so commonplace that there is a tendency for the industry not to give such apparetus the full measure of credit that it deserves in any particular disaster , therefore , the data presented herein should give some idea of what has been done in this regard during the past 15 years that is , up to 1910 by the Technologic Branch of the U. S. Geological Survey , and thence ( to the end of 1922) by the U. S. Bureau of Mines .

Feb 1, 1923

By John R. Reeves

The development of an new industry, which must prepare its marketable products at or near the source of the raw material, and ship them to a market which may cover half a nation, is more or less influenced by a number of natural and cultural conditions such as (1) location of plants with respect to a large market, (2) climatic conditions, (3) transportation facilities, (4) labor supply, and (5) water supply. An effort is made in this pager to give in detail a number of the more important of these conditions as they affect, either favorably or unfavorably, the development of the oil-shale resources of southeastern Indiana. The utilization of the New Albany formation for the production of oil will be similar to a large scale low-grade ore proposition in which the raw material can be obtained in very large quantities at a relatively low cost. It appears, therefore, in considering the value of this shale or its economic position in relation to other oil shales, tie cost of mining and preparation for the retort are of prime importance.

Jan 1, 1923

By Clyde L. Brown

Recent developments in portable communication equipment for use in emergency recovery work following mine fires and explosions have wade possible a convenient and dependable means of directing rescue teams working under hazardous conditions. INTRODUCTION Mine rescue and recovery operations following; fires and explosions are frequently conducted under adverse conditions that require the use of oxygen breathing apparatus by members of a 5- or 6-man team. Conventional apparatus used for this purpose for many years was equipped with an oxygen supply adequate for at least 2 hours. The design of the apparatus is such that the nose passages are closed with a clamp, and breathing is accomplished through a mouthpiece connected to the apparatus by tubes and arranged to prevent inhaling air or gases from outside sources. The use of the mouthpiece has presented difficulties in the development of telephone communication because of the wearer's inability to speak while wearing the mouthpiece. The method of conducting operations of rescue teams requires a person to direct operations at a fresh-air base as close to the rescue team as possible. At least one standby rescue team and 2 or 3 other persons assigned to various tasks are stationed at the fresh-air base. An efficient and reliable means of communication between the director of operations and the rescue team is necessary for reasonably safe and efficient work in hazardous areas.

Jan 1, 1957

By Harry E. Tufft

Data were obtained by the writer from a number of the large coul-mine operators in Illinois, on the consumption and cost of timber used in their mines and the quality of the timber now being used as compared with former years. This information supplemented by comparative date for previous years published in bulletins of the filinois Coal Mining Investigation series, and other sources, is presented below. This survey is part of a cooperative study with the . S. Forest Service, of the mine timber situation, with particular regard to the economies to be derived by better selection, preparation, and storage of timber, and especially treatment with preservatives to prolong the life. Geo. S. Rice, chief mining engineer of the J. S. Bureau of Mines, under whose general direction the work was done, gave valuable advice and criticism. R. B. Miller, State Forester, contributed helpful data which he had recent- ly obtained in an independent study of the mine-timber situation in Illinois.

Apr 1, 1923

By J. Shawn Peterson, David S. Yantek, Adam K. Smith

Exposure to excessive noise over time can cause permanent hearing loss. Workers in the mining industry are frequently exposed to A-weighted sound levels in excess of 90 dB. The A-weighted sound level at the roof bolter operator’s location can exceed 100 dB while drilling. The National Institute for Occupational Safety and Health (NIOSH) measured the sound pressure at the roof bolter operator’s position and utilized a phased array of microphones with beamforming software to identify noise sources on a roof bolting machine while drilling. The test data indicates the sound level at the operator’s position is dominated by the 2000 Hz through 5000 Hz one-third­octave-band sound levels. The beamforming results indicate that the drilling noise is primarily from two areas: the portion of the drill steel just below the rock and the drill steel-chuck interface. This paper will discuss the methods used to identify the primary noise sources.

By Charles L. Kimbell

Available statistics on 1989 worldwide consumption of selected nonfuel minerals shown in table 5 show increases for 11 of 14 listed nonfuel mineral commodities with 1 unchanged from the 1988 level, a departure from the pattern of the past 2 years, in which each of the listed commodities registered gains. The 1989 results, however, were better than those for 1986 when only seven listed nonfuel mineral commodities recorded gains with one un- changed from 1985. Consumption of the two ferrous metal raw materials listed advanced as functions of increased output of pig iron and crude steel. The increase in iron ore consumption exceeded the increase in iron ore output, suggesting a slight drawdown of world iron ore inventories. The estimated in- crease in iron and steel scrap consumption was slightly greater than the minuscule increase in world steel production, but it is believed that there was little change in the ratio of iron ore to scrap in steel plant feed on a global basis.

Jan 1, 1992

Reduce the dust exposure to the operator of a longwall shearer with a novel foam spray system. Approach Discharge foam through the nozzles of a shearer drum so that foam and coal are better mixed. How It Works Bureau of Mines research showed that two very important principles for successful application of foam are: (1) moisture distribution and (2) degree of mixing. Foam can distribute a given quantity of moisture much more evenly over a large surface area. Successful Bureau tests of foam for dust control always involve a high degree of mixing between the foam and the material, Mixing, permits a greater distribution of foam throughout the mined product. The most suitable location of foam application would be at the point where the dust is generated, before the dust becomes airborne. Foam nozzles located in the cutter drum (pick face foaming or ejecting foam through scroll sprays) will suppress dust close to its source.

Jan 1, 1989

By C. M. Frost

The hydrodesulfurization characteristics of a Venezuelan topped crude oil and a Venezuelan reduced crude oil were determined at temperatures from 740° to 850° F, pressures from 800 to 1,600 psig, and space velocities from 1.0 to 2.0 Vo/Vc/hr. Kinetic calculations showed that under these conditions the desulfurization reaction was first order with respect to sulfur and had an average activation energy of 32.5 kcal/mo1. Catalyst life tests made at 750° F, with pressures of 800, 1,200, and 1,600 psig and space velocities of 1.0 and 1.25 Vo/Ve/hr, showed that the decrease in the relative activity of the catalyst was a logarithmic function of time or volume of oil processed and the amount of vanadium deposited on the catalyst. Comparative tests made with residual fuels prepared from a Wilmington, Calif., crude oil and a Wyoming asphaltic crude oil showed that catalyst life may be extended by processing fuel oil with a low metal content, but it may be shortened by the presence of large amounts of asphalt in the feed.

Jan 1, 1971

By R. E. Mussler

As part of an overall goal to develop technology that can maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines is evaluating a method for selectively extracting nickel and cobalt from low-grade domestic laterites. The method involves electrowinning to recover the metals in pure form; therefore, preliminary laboratory-scale electrowinning tests were conducted in both a nondiaphragm and a diaphragm cell to determine the effect of variables on energy efficiency under controlled conditions. Electrolytes were generally reagent-grade sulfate solutions that were prepared to simulate electrolyte that could be obtained by stripping nickel-and cobalt-rich solvent extraction reagents. Limited tests were conducted with electrolyte generated from laterite leach solutions. Electrical energy consumption in a nondiaphragm cell was 2.06 kwhr/lb Ni with the cell operated at 50° C, a cell feed of 90 g/l Ni, a pH of 3.5, an extraction of 3.2 g/l, and a cathode current density of 20 amp/ft2. The energy requirement decreased with increasing concentration and temperature, and increased with increasing. extraction and current density. At 50° C, energy consumption in the nondiaphragm cell was 21 pct greater than in the diaphragm cell, but it was only 5 pet greater at 65° C. For this reason and because of overall cost considerations, operation at 65° C with the nondiaphragm cell was preferred. Smooth sheets of cobalt were obtained by electrowinning in a nondiaphragm cell at selected temperatures from 50° to 85° C and with cobalt concentrations from 55 to 87 g/l. The energy consumption (1.48 kwhr/lb) was 22 pet lower with a cobalt concentration of 75 g/l and a cell temperature of 65° C than with a cobalt concentration of 55 g/l and a cell temperature of 50° C.

Jan 1, 1981

By W. T. Millar

Magnetite mines in the Sterling tract, Orange County, N. Y., were operated almost continuously from pre-Revolutionary days until 1923. The Red-Back mine, one of several in this tract, was discovered in 1780; operated briefly in 1880; and abandoned, presumably because the iron ore contained considerable sulfur. The mine is in rough, mountainous country, with altitudes ranging from 500 to 1,100 feet. The magnetite deposit occurs in complex metamorphosed pre-Cambrian formation and is thought to be a replacement of limestone by magnetite. A dip-needle survey, completed in 1916, traced magnetic anomalies for a mile along the outcrop. A preliminary examination of the Red-Back mine was made by W. T. Millar, Bureau of Mines engineer, in December 1942. The Bureau of Mines bored seven diamond-drill holes aggregating 2,727.6 feet during the winter of 1943-44. A zone of magnetite mineralization was intersected in each of the holes.

Jan 1, 1949

By H. E. Powell

The mineral dressing research here reported is part of a continuing program by the Bureau of Mines to develop new or improved concentration processes for oxidized or partly oxidized lead and zinc ores. A sample of low-grade sulfide-oxide, lead-zinc ore from Jasper County, Mo., containing galena, cerussite, pyromorphite, hemimorphite, smithsonite, and sphalerite was concentrated by froth flotation and tabling to a grade of 66 percent lead. Because of the presence of a high content of slime-size values, the overall recovery of lead was limited to 64 percent at this grade. Tests to recover the zinc by froth flotation and by gravity concentration did not give satisfactory results. INTRODUCTION Since its establishment, the Rolla Metallurgy Research Center has con-ducted studies of base metals as a part of its overall program (1, 2, 3, 4, 5,6,7).3/ This research has been, and is, directed to beneficiating complex and submarginal ores, to retreating rejects from commercial installations, and to developing fundamental data.

Jan 1, 1960

By Ernest R. Rodriguez, Allen D. Look

"INTRODUCTION The underground mine of the Miami Copper Co. has operated since 1927 without a fatality from blasting or the handling of explosives. To improve safety and efficiency, electrical blasting has been used exclusively since 1934. During the period January 1, 1934, to December 31, 1948, inclusive, over 4,000 tons of explosives were used to produce 60,925,071 tons of ore with 896,760 feet of development footage and 2,591,788 square feet of undercut area.The purpose of this paper is to recount the company's precautions to insure safe handling of explosives at this operation, where safety involves careful planning rather than ""trial and error.""GENERAL INFORMATIONThe Miami Copper Co. operates on underground mine in a large, low-grade, Porphyry copper deposit near Miami, Ariz. The deposit contains numerous fractures and planes of weakness, which contribute to ease of working the ore bodies by the block-caving method of mining.An individual stope-caving method is used with stoles 150 feet by 200 to 300 feet and 30- to 50-foot pillars between stapes. After the stope is undercut, the ore is drawn through the draw raises on the grizzly level, and thence through the transfer raises to the ore chutes on the haulage level.Access to the mine is by four active shafts, three of which are primarily for ventilation. No. 5 shaft is used for both hoisting and service. There are four operating levels in the mine. The elevations of the grizzly levels are governed by the contour of the bottom of the ore body and therefore vary in different locations in, the mine.Grizzly levels are on the 850, 900, and 975 levels. The 1,000 level is the haulage level. This mine operates in very low-grade ore and requires economical handling of large tonnages safely and efficiently."

May 1, 1950

By R. A. Guereca

The Bureau of Mines conducted an analysis to determine criteria for steady-state, laminar flow boundary conditions for a coiled-tube gas viscosimeter by comparing experimental data from a thick-walled, stainless steel capillary in a horizontal, straight-tube condition, with similar data taken after the same capillary was formed into a helix. Overlapping volumetric f10wrates and pressure drops are covered for both configurations at pressure levels of 28, 225, and 1,000 psia at 3000 K. Friction factor, Reynolds number, and Dean number correlation plots show conditions where the coi1ed-tube flow deviates from straight-tube flow. The coiled-tube data indicate departure from Poiseui11e steady-state laminar flow at a Reynolds number close to 390 and a Dean number of about 15. Below these conditions and consistent with the data reported, Dean's circulation appears negligible. For the particular coil used, a conservative upper limit of 10 is chosen for the Dean number corresponding to an upper limit of about 250 for the Reynolds number.

Jan 1, 1967

By Arthur L. Murray

"While serving as surgeon with rescue car No 11 of the U. S. Bureau of Mines, the writer visited the principal metal-mining camps of Utah during the latter part of 1919. In visiting the mines, meeting and conversing with miners, and talking over the medical situation with physicians in the various camps, the number of cases of lead poisoning encountered was great enough to attract attention.With a view to procuring more definite information as to the number and distribution of cases of lead poisoning throughout the State, a study of the records of the State Board of Health was undertaken. Utah had no ordinance re¬quiring the reporting of occupational diseases, so it was not possible to secure data an cases A study of the mortality records by years gave the following results.:Year Deaths from lead poisoning.1910,11911,01912,21913,11914,61915,41916,11917,31918,11919,2These few deaths would seem to indicate a fairly low case rate, but when it is realized that lead poisoning is rarely an immediate cause of death and that the train of sequelae in this disease frequently leads to chronic involvemeets of the digestive, nervous, circulatory or genito-urinary systems, it is apparent that the number of deaths showing lead poisoning as the cause can not be taken as an index of the cases prevalent. The time elapsing between the presence of the active signs of lead poisoning and the terminal illness from pathologic conditions excited by lead absorption may be years, and the initial cause, lead poisoning, is frequently lost sight if entirely, hence the death certificate shows no evidence of the primary cause."

Aug 1, 1921