Search Documents

By A. A. Angelov

This paper presents a unique method of monitoring the effectiveness of the planning process as well as the execution of mine plans. The method primarily determines the degree of deviation from the original mine plans by comparing actual mined areas to initially planned mining areas. The performance of mining operations is also measured by comparing actual and planned tonnages for a particular period. Once the degree of deviation from mine plans has been established the cause/s of the deviation can be determined through a simple fault tree analysis. Accurate identification of the reasons of deviation can aid the mine in selecting possible methods to correct the deviation. It is, however, beyond the scope of this paper to discuss the methods employed in correcting such deviations, as each mining operation will have unique causes of plan deviation and methods of remedying them. Deviations from the plan greatly affect the yields obtainable, which in turn affects the life of mine, thus having negative economic and financial implications. Accordingly, this paper presents a project management method which aims to reduce risk by improving planning systems to ensure optimum overall extraction of coal reserves.

Jan 1, 2010

By X. Q. Cao, D. S. Zhang, L. Q. Ma

To solve the support stability control problem for a coal face with large angles along both strike and dip (CLSD), the ’support-surrounding rock’ mechanical model has been developed, which takes into account the impact of the dip angle of the seam on the stability of the support in the strike direction. The mechanical relationships of the critical topple angle and critical slip angle of the support along the strike of the coal face with large dip angle and the support height, support resistance, friction coefficient, and other factors have been derived through the mechanical analysis of support stability in the strike direction of CLSDs in the free state, the operating state, and the special state. The research findings were applied to a fully mechanized CLSD in Xinji Coal Mine. The maximum underhand angle and overhand angle in strike are 42° and 25° respectively, and the maximum dip is 39°. It is calculated that during underhand mining and overhand mining, the critical support resistances for avoiding support toppling are 3723 kN and 1714 kN respectively, and the critical support resistances for avoiding slipping of the support are 7405 kN and 6606 kN respectively. Thus, the selection of type ZZ7600/18/38 hydraulic roof support for the coal face is justified. Measures to prevent sliding of the support and the installation of a limiting stop maintain the support runs in good condition and ensure safe and efficient mining of CLSD.

Jan 1, 2015

By C. Scheffer

This paper describes a model that can simulate the behaviour of a pneumatic intensifier that is generally referred to as an ?air pump? (AP). The AP is used in many South African underground mines, and utilizes compressed air with pressures between 0.3?0.6 MPa to pump water up to pressures of 12?18 MPa. The high pressure water is used in numerous underground mines to pressurize props and roof bolts that act as safety and roof support devices. The simulation model reproduces the intensifier's operation under various conditions and therefore can be used to investigate the AP's sensitivity towards environmental conditions, design parameters (such as spring stiffness, plunger diameter, nozzle diameter etc.) and operating conditions. Model validation by comparison with laboratory experiments showed good correlation. The model can subsequently be used to investigate design changes aimed at improving the AP's performance and reliability over a wider range of operating conditions.

Jan 1, 2005

By F. S. A. de Frey

The author would like to refer to his contribution to the paper `Design of pillar systems in South Africa' by Ozbay et al. 1. The authors agreed `wholeheartedly that further research, together with carefully planned field trials, in pursuit of this potentially highly rewarding concept' of the small span small pillar method is warranted. On 30 September 2010 the author went underground at the Kroondal Chrome Mine to observe how the concept of smaller spans was being applied. He was pleasantly surprised to find that the typical coal mine bord and pillar sytem was being used very successfully. Although the deepest mining was taking place at a depth of only 450 metres, Kroondal would be an ideal mine to do further research together with carefully planned field trials. At Crown Mines Gold Mine, where the author worked, he was informed that the first recorded rockburst took place at a depth of 635 metres below surface. The depth of the platinum and chrome mines is increasing, with the risk of an excalation in injuries and fatalities due to 'backbreaks' and siesmic activity. The rock engineer at Kroondal was not aware of backbreaks occuring on the mine. It is important that the rock engineers of the base mineral and gold mines get together and give more serious attention to the host rock environment in which the pillars are situated.

Jan 1, 2011

By Q. Cheng

This paper introduces the multi fractal interpolation method (MIM)developed for handling singularities in data analysis and for data interpolation. The MIM is a new moving average model for spatial mapping and interpolation. The model decomposes the raw data into two components: singular and nonsingular components. The former can be characterized by a localized singularity index that quantifies the scaling invariance property of measures from a multifractal point of view. The latter is a smooth component that can be estimated using ordinary kriging or other moving average models. The local singularity index characterizes the concave/convex properties of the neighbourhood values. The paper utilizes a binomial multiplicative cascade model todemonstrate the generation of one- and two-dimensional data with multi-scale singularities which can be modelled by asymmetrical multifractal distribution. It then introduces a generalized moving average mathematical model for analysing and interpolating data with singularities. Finally, it is demonstrated by a one-dimensional case study of de Wijs’ data from a profile in a zinc mine, that incorporation of spatial association and singularity can improve the interpolation result, especially for observed values with significant singularities.

Jan 1, 2015

By D. Malovichko

Seismic events and pillar failures observed in two platinum mines in the Rustenburg area, South Africa, were investigated. We studied the sources of approximately 300 largest seismic events recorded in 2009. Moment tensors of these events were estimated from amplitudes and polarities of P- and S-waves. The inverted mechanisms contain isotropic implosive components in many instances. Analyses of uncertainty of the moment tensor solutions confirmed the significance of the implosive component in general. Several documented cases of pillar failure were considered in detail. For each of these a seismic moment tensor was calculated from an elastic stress model assuming an instant removal of a failed pillar. The geometries and magnitudes of the theoretical seismic moment tensors are in agreement with the observed (i.e. inverted from seismic data). The results indicate that either pillar failure or fracturing in the proximity of the reef (within a fraction of the dominant wavelength of seismic waves) are responsible for a significant portion of the large events recorded in these mines.

Jan 1, 2012

By A. D. Pelton

The evolution of thermodynamic models of molten salts and slags, starting with Temkin in 1948, has culminated in today?s sublattice models. These modern models have permitted the development of large thermodynamic databases of model parameters, which can be used to calculate and predict accurately the properties of multicomponent solutions. The model parameters are mainly obtained by the critical evaluation and optimization of available thermodynamic and phase equilibrium data for binary and ternary subsystems. The models are then used to estimate the properties of multi component slags and salts from these assessed binary and ternary parameters. When used in conjunction with thermodynamic databases for solids and solid solutions (salts, oxides, sulphides, metals, etc.), other liquid solutions (such as liquid metals),and gases, these databases permit the calculation of complex multiphase equilibria in multicomponent systems, with applications in a wide variety of industries. These calculations can be performed with general commercial software for Gibbs energy minimization, which can also be incorporated into process simulation software packages. Keywords: slags, salts, solution models, thermodynamics, phase diagrams, oxide systems, molten salts

Jan 1, 2004

By W. P. Erasmus

This paper will focus on the use of the ?wet-mix? steel fibre re-in forced shotcrete as a permanent lining in deep shafts, assessing gold bearing reef. It will cover all aspects relating to the choice of this material covering the geological conditions through to the final quality control. All procedures are in line with ISO 9001,as JCI projects who manage the project, are an approved company therof.

Jan 1, 2001

By R. C. D. Phillis

The management of critical resource inventories is an important productivity lever and a significant risk factor?risk in the sense that poor resource availability lends itself to disempowerment of workers, unsafe work practices, wasted spending (high unit costs),and poor quality of work (including mining waste/rework). Most underground platinum mines experience lost blasts that directly lead to reduced productivity. In most surveyed shafts, 30% of lost blasts can be attributed to shortages of critical material and/or equipment. The problem is prevalent despite the existence of conventional transitory surface and underground stores. This paper discusses the introduction of buffer stores as a complementary materials storage system in order to improve health and safety in mines as well as reduce lost blasts. Both quantitative and qualitative results have shown that buffer stores result in dramatic improvements in productivity and are readily acceptable by stakeholders. Keywords Buffer stores, lost blast.

Jan 1, 2011

By V. Yahorava

Resin-in-pulp (RIP) technology has recently often been considered for the direct recovery of base metals and uranium from dense pulps. Implementation of RIP will eliminate the requirement for any solid-liquid separation downstream of leaching and has the potential to combine the recovery and purification steps, hence reducing both capital and operating costs. The recovery of the valuable metal is expected to be higher when RIP is used, especially where the leached solids are difficult to settle or filter, and to wash. The main concerns about the use of RIP for uranium recovery from dense pulps are the impact of silica on the resin?s metallurgical performance and the operating costs that would be associated with resin loss. Although a number of resin manufacturers have been developing much improved RIP-grade resins, it is critical that the most cost-effective resin be selected. Mintek currently is doing a significant amount of work on silica fouling of RIP-grade strong-base resins in acidic leach liquors and the effect it has on the performance of the resin, including its durability. This paper describes the results of the test work done on silica fouling and its impact on plant design input data. Resin durability test work was done using various laboratory techniques, but durability was also evaluated on a relatively large scale using actual pumps, screens, and mechanical agitation. Based on the results generated, a preliminary economical evaluation was done to estimate the impact of resin loss on the overall economic viability of a specific application. Keywords: resin-in-pulp, silica fouling, resin loss, equilibrium, kinetics, elution, durability, mechanical strength, resistance to attrition.

Jan 1, 2009

By B. Solar Menéndez, M. B. Díaz Aguado, I. Á. Fernández, C. González Nicieza

The analysis of subsidence due to the opening of an underground void (mining, water exploitation or civil works hole) is a problem usually hard to solve. First of all, it requires a predictive model, in order to define both the displacement magnitude and area affected by subsidence. Such model should be validated with measurements of the actual movements sustained on the surface, in order to adjust it properly and enable influence of future behaviour in a reliable way. Two different kinds of problems might arise. On one side, it is necessary to control and measure surface movements in a very exhaustive way during a long period of time, beginning before underground works take place and finishing years after they are over. Furthermore, three factors bring in errors, some times of magnitudes higher than the displacement magnitudes measured. These include: the fact that reliable and long-term information cannot always be achieved; the precision of measuring devices; and the design of the topographical network itself. In addition, the predictive models more widely used only apply to certain excavation geometries, mainly to horizontal holes. In light of this background, the Group of Rock Engineering, of the University of Oviedo Mining Department, has developed a working methodology and a specific software tool, Subsidence 3D, to estimate ground displacements and strains. The program will allow for predictive models to be defined and also allows the treatment of data related with topographical marks and its comparative analysis with calculated results. The software has been programmed using Visual C++. Graphical outputs however are generated using AutoCAD 2000. This paper mainly refers to a practical situation, an underground coalmine, remarking the main difficulties arisen during the study of the available information and proposing how to solve them. A predictive model in subsidence 3D was established and validated. The actual behaviour of the ground was that in the model.

Jan 1, 2003

By Y. I. Yang, Y. -B. Tang, D. -J. Ma

Chlorine-containing minerals are commonly present in coal. Associated minerals such as pyrite can undergo exothermic reactions. Consequently, it is of great significance to study the effect of inorganic chloride on the spontaneous combustion of coal. In this study, the effects of five inorganic chlorides (sodium chloride, magnesium chloride, potassium chloride, calcium chloride, and zinc chloride) on the spontaneous oxidation of coal were investigated. Analysis of the gaseous products of coal oxidization at low temperatures (323K to 453K) showed that the presence of inorganic chlorine in coal markedly decreases O2 consumption and the generation of CO and CO2. Samples of raw coal and chlorine-loaded coal were oxidized for 36 hours under the same experimental conditions. Infrared diffuse reflectance spectroscopy results showed that inorganic chloride can inhibit the oxidative decomposition of some functional structure components (methyl, methylene, methine, and hydroxy) in the coal. The influence of inorganic chloride on the oxidation characteristics of the functional groups in coal during spontaneous combustion was investigated using benzyl alcohol and 1-phenylpropanol as model compounds, which were tested under the same experimental conditions as the coal samples. The oxygen consumption of model compounds with and without the addition of inorganic chloride further suggested that inorganic chloride may hinder the oxygenolysis of these structures during low-temperature oxidation. This phenomenon can be attributed to the radical reaction from the perspective of radical chemistry. It can therefore be concluded that inorganic chlorides play an inhibitory role in the spontaneous combustion of coal.

Jan 1, 2015

By J. N. Van der Merwe

Due to the approaching depletion of reserves in the Witbank Coalfield, and the fact that the Waterberg Coalfield is as yet under developed, there is increasing pressure to extend the lives of the operating coal mines in the Witbank Coalfield. One potential source of coal is the old pillars, often small and at shallow depth, that were not left with secondary extraction in mind. At face value, some of these pillars appear to be suitable for secondary mining due to their high safety factors. However, it is known that over time, these pillars have scaled and the current sizes are smaller than the as-mined dimensions. It is also known that at shallow depth, the overburden is often less likely to fail during secondary mining, resulting in high abutment loads on the unmined pillars. The paper proposes a systematic method to pre-evaluate those old pillars for the possibility of stooping. The method consists of elements of fundamental methods and newly developed technology. In essence, it revolves around using empirical methods to estimate current pillar dimensions, followed by numerical modelling to investigate the probability of progressive pillar failure and then fundamental methods to determine the limits of applicability of the numerical model.

Jan 1, 2012

By M. Gous

Keywords: Pyrometallurgy, Namakwa Sands, ilmenite, DC arc furnace, titania slag, pig iron Namakwa Sands is a heavy minerals mining and beneficiation business in the Anglo Base Metals Division, and operates along the West Coast of South Africa. The business encompasses mining, mineral concentration, separation, and smelting operations. The smelting process comprises the carbonaceous reduction of ilmenite to produce titania slag with a TiO2 content of 86%, and iron with a carbon content of 2.5%. The Namakwa Sands smelter, situated near the Saldanha Bay harbour, commenced smelting operations in 1994, when a 25 MW DC arc furnace was commissioned. The smelting operations were expanded in 1999, with the commissioning of a second 35 MW DC arc furnace. Despite the fact that ilmenite smelting poses a technical challenge in terms of the high temperatures required, the physical characteristics of the slag, the constraints placed on the feedstock, and the tight product specifications, Namakwa Sands has continually increased slag production since 1995. High furnace feed-on utilisation and furnace stability, complemented by continuous improvement drives, will be the vehicle to drive performance in the short term, with longer-term performance enhancements due to strategic process development.

Jan 1, 2006

By G. V. R. Landman

It is self-evident that economic pressure demands that today?s mines stay ahead and stay competitive. The challenge, however, isto find fresh approaches to the pursuit of efficiency and operational effectiveness. Rather than focusing on individual activities in isolation, a process that can lead to poor investment decisions affecting other critical areas of operation, a key concept is optimization of the whole value-adding process of mining. This concept is often called ?mine to mill?. Whereas it is never easy to establish optimal conditions across a whole mining operation, the quality and consistency of the blasted rock strongly affects all operations. In many instances an inability to control rock breaking has been unchallenged, leading to significant investment in time and money to manage the consequences of poor and/or inconsistent rock breaking. This paper discusses how electronic initiation systems can play a major role in optimizing the whole mining operation. Electronically programmed detonators provide not only the ability to tightly control a key parameter, namely timing, but also the opportunity to extract blast data for a continuous improvement process. The ability to alter predictably, using feedback from the downstream processes, blasting variables such as fragmentation, throw, wall stability, and vibration, is a huge advantage. The current understanding of the effect of timing, accuracy, and scatter on rock fragmentation is reviewed and offers reasons why there is significant progress in controlling blast results. Two case studies are examined, which demonstrate the benefits of the technology on the economics of the operations under review.

Jan 1, 2010

By N. Sutcliffe

Refractories and slags play a vital role in the production of stainless steel. They are in intimate contact with the steel at temperature, and chemical reactions between the three can and do occur. These interactions can be beneficial, in the case of active tundish and ladle slags, and negative in the case of refractory erosion and slag entrapment. This paper presents the results of both plant trials and laboratory investigations of steel/refractory and slag/refractory interactions. The interaction mechanisms observed are described leading to selection criteria for new refractory products. Keywords: slags, steels, refractories, reaction mechanisms.

Jan 1, 2004

By R. A. Harris

In this study Pt-Al thin films were prepared via electron beam physical vapour deposition (EB-PVD) with an atomic concentration ratio of Pt25:Al75. These films were heat treated at temperatures ranging from 150°C to 650°C for annealing times from 4 to 60 minutes. The resulting microstructure of these thin films were obtained via secondary electron imaging used in conjunction with depth profiling with the aid of scanning auger microscopy (PHI 700).Elemental maps of the micrographs were obtained. Simulations, based on a chemical potential Monte Carlo method1, were run for various interaction parameters. From these simulations theoretical depth-profiles and proposed microstructures were obtained. These were compared to the experimentally measured depth profiles and elemental maps. Keywords Monte Carlo, chemical potential, depth profile, Pt-Al thin films.

Jan 1, 2011

By A. P. Squelch

The question of what stress condition exists in the hangingwall of tabular stopes remains topical and largely unanswered. Limited field data exist to quantify the situation and provide calibration for investigative computer modelling exercises. Work conducted in1989 and 1990 under a Chamber of Mines Research Organization (now the CSIR: Division of Mining Technology) programme of research into the behaviour and benefits of backfill may assist with this situation. The original work was motivated by the premise that the improved hangingwall stability in backfilled panels (identified by rockfall accident analyses) is due to a change in the hangingwall stress regime. Current, largely theoretical, studies into mechanisms of stope hangingwall behaviour and support interaction could benefit from considering these data. Keywords: Backfill, horizontal stress, stope hangingwall, hangingwall stability, support interaction.

Jan 1, 2002

By A. J. Vietti

A pilot plant paste thickening campaign was conducted at the Anglo Platinum Limited Mogalakwena South Concentrator plant in South Africa in order to determine the water saving capability of P&TT technology. In the process a simple water consumption model was developed for estimating the overall water consumption of the mine. The model indicates that for the Mogalakwena tailings, significant water savings are achieved by discharging thickened tailing directly to the TSF but only at densities where free water release at the TSF is close to zero. Keywords Paste, thickened tailings, thickener, water savings, water consumption.

Jan 1, 2011

By Mark Van Kleek

CONTENTS ?The Falcon C ?Data from a Production Trial ?Methodology ?Scale-up ?Test Results ?Circuit Configurations ?Conclusion

Jan 1, 2006